Abstract: The manufacturing technology of band cotton is very
delicate and depends to choice of certain parameters such as torsion
of warp yarn.
The fabric elasticity is achieved without the use of any elastic
material, chemical expansion, artificial or synthetic and it’s capable
of creating pressures useful for therapeutic treatments.
Before use, the band is subjected to treatments of specific
preparation for obtaining certain elasticity, however, during its
treatment, there are some regression parameters. The dependence of
manufacturing parameters on the quality of the chemical treatment
was confirmed.
The aim of this work is to improve the properties of the fabric
through the development of manufacturing technology appropriately.
Finally for the treatment of the strip pancake 100% cotton, a
treatment method is recommended.
Abstract: This article presents summary on preparation and
characterization of zinc, copper, cadmium and cobalt chromite
nanocrystals, embedded in an amorphous silica matrix. The
ZnCr2O4/SiO2, CuCr2O4/SiO2, CdCr2O4/SiO2 and CoCr2O4/SiO2
nanocomposites were prepared by a conventional sol-gel method
under acid catalysis. Final heat treatment of the samples was carried
out at temperatures in the range of 900−1200 ◦C to adjust the
phase composition and the crystallite size, respectively. The resulting
samples were characterized by Powder X-ray diffraction (PXRD),
High Resolution Transmission Electron Microscopy (HRTEM),
Raman/FTIR spectroscopy and magnetic measurements. Formation
of the spinel phase was confirmed in all samples. The average size of
the nanocrystals was determined from the PXRD data and by direct
particle size observation on HRTEM; both results were correlated.
The mean particle size (reviewed by HRTEM) was in the range from
∼4 to 46 nm. The results showed that the sol-gel method can be
effectively used for preparation of the spinel chromite nanoparticles
embedded in the silica matrix and the particle size is driven by the
type of the cation A2+ in the spinel structure and the temperature
of the final heat treatment. Magnetic properties of the nanocrystals
were found to be just moderately modified in comparison to the bulk
phases.
Abstract: The organizations of European and Czech critical
infrastructure have specific position, mission, characteristics and
behaviour in European Union and Czech state/business environments,
regarding specific requirements for regional and global security
environments. They must respect policy of national security and
global rules, requirements and standards in all their inherent and
outer processes of supply - customer chains and networks. A
controlling is generalized capability to have control over situational
policy. This paper aims and purposes are to introduce the controlling
as quite new necessary process attribute providing for critical
infrastructure is environment the capability and profit to achieve its
commitment regarding to the effectiveness of the quality
management system in meeting customer/ user requirements and also
the continual improvement of critical infrastructure organization’s
processes overall performance and efficiency, as well as its societal
security via continual planning improvement via DYVELOP
modelling.
Abstract: This paper attempts to evaluate the effect of fire
damage on concrete by using nonlinear resonance vibration method,
one of the nonlinear nondestructive method. Concrete exhibits not
only nonlinear stress-strain relation but also hysteresis and discrete
memory effect which are contained in consolidated materials.
Hysteretic materials typically show the linear resonance frequency
shift. Also, the shift of resonance frequency is changed according to
the degree of micro damage. The degree of the shift can be obtained
through nonlinear resonance vibration method. Five exposure
scenarios were considered in order to make different internal micro
damage. Also, the effect of post-fire-curing on fire-damaged concrete
was taken into account to conform the change in internal damage.
Hysteretic nonlinearity parameter was obtained by amplitudedependent
resonance frequency shift after specific curing periods. In
addition, splitting tensile strength was measured on each sample to
characterize the variation of residual strength. Then, a correlation
between the hysteretic nonlinearity parameter and residual strength
was proposed from each test result.
Abstract: Load Forecasting plays a key role in making today's
and future's Smart Energy Grids sustainable and reliable. Accurate
power consumption prediction allows utilities to organize in advance
their resources or to execute Demand Response strategies more
effectively, which enables several features such as higher
sustainability, better quality of service, and affordable electricity
tariffs. It is easy yet effective to apply Load Forecasting at larger
geographic scale, i.e. Smart Micro Grids, wherein the lower available
grid flexibility makes accurate prediction more critical in Demand
Response applications. This paper analyses the application of
short-term load forecasting in a concrete scenario, proposed within the
EU-funded GreenCom project, which collect load data from single
loads and households belonging to a Smart Micro Grid. Three
short-term load forecasting techniques, i.e. linear regression, artificial
neural networks, and radial basis function network, are considered,
compared, and evaluated through absolute forecast errors and training
time. The influence of weather conditions in Load Forecasting is also
evaluated. A new definition of Gain is introduced in this paper, which
innovatively serves as an indicator of short-term prediction
capabilities of time spam consistency. Two models, 24- and
1-hour-ahead forecasting, are built to comprehensively compare these
three techniques.
Abstract: Metal-enhanced Luminescence of silicon nanocrystals
(SiNCs) was determined using two different particle sizes of silver
nanoparticles (AgNPs). SiNCs have been characterized by scanning
electron microscopy (SEM), high resolution transmission electron
microscopy (HRTEM), Fourier transform infrared spectroscopy
(FTIR) and X-ray photoelectron spectroscopy (XPS). It is found that
the SiNCs are crystalline with an average diameter of 65 nm and FCC
lattice. AgNPs were synthesized using photochemical reduction of
AgNO3 with sodium dodecyl sulphate (SDS). The enhanced
luminescence of SiNCs by AgNPs was evaluated by confocal Raman
microspectroscopy. Enhancement up to x9 and x3 times were
observed for SiNCs that mixed with AgNPs which have an average
particle size of 100 nm and 30 nm, respectively. Silver NPs-enhanced
luminescence of SiNCs occurs as a result of the coupling between the
excitation laser light and the plasmon bands of AgNPs; thus this
intense field at AgNPs surface couples strongly to SiNCs.
Abstract: Diabetes is a growing health problem in worldwide.
Especially, the patients with Type 1 diabetes need strict glycemic
control because they have deficiency of insulin production. This
paper attempts to control blood glucose based on body mathematical
body model. The Bergman minimal mathematical model is used to
develop the nonlinear controller. A novel back-stepping based sliding
mode control (B-SMC) strategy is proposed as a solution that
guarantees practical tracking of a desired glucose concentration. In
order to show the performance of the proposed design, it is compared
with conventional linear and fuzzy controllers which have been done
in previous researches. The numerical simulation result shows the
advantages of sliding mode back stepping controller design to linear
and fuzzy controllers.
Abstract: Artemisia species, which are medically beneficial, are
widespread in temperate regions of both Northern and Southern
hemispheres among which Iran is located. About 35 species of
Artemisia are indigenous in Iran among them some are widespread in
all or most provinces, yet some are restricted to some specific
regions. In this review paper, initially, GC-Mass results of some
experiments done in different provinces of Iran are mentioned among
them some compounds are common among species, some others are
mostly restricted to other species; after that, medical advantages
based on some researches on species of this genus are reviewed;
different qualities such as anti-leishmania, anti-bacteria, antiviral as
well as anti-proliferative could be mentioned.
Abstract: Nonalcoholic fatty liver disease (NAFLD) has
increased in conjunction with obesity. The accuracy of risk factors
for detecting NAFLD in obese adolescents has not undergone a
formal evaluation. The aim of this study was to evaluate predictors of
NAFLD among Egyptian female obese adolescents. The study
included 162 obese female adolescents. All were subjected to
anthropometry, biochemical analysis and abdominal ultrasongraphic
assessment. Metabolic syndrome (MS) was diagnosed according to
the IDF criteria. Significant association between presence of MS and
NAFLD was observed. Obese adolescents with NAFLD had
significantly higher levels of ALT, triglycerides, fasting glucose,
insulin, blood pressure and HOMA-IR, whereas decreased HDL-C
levels as compared with obese cases without NAFLD. Receiver–
operating characteristic (ROC) curve analysis shows that ALT is a
sensitive predictor for NAFLD, confirming that ALT can be used as a
marker of NAFLD.
Abstract: Due to reduced stiffness, research on second
generation titanium alloys for implant applications, like the
metastable β-titanium alloy Ti-15Mo, become more and more
important in the recent years. The machinability of these alloys is
generally poor leading to problems during implant production and
comparably large production costs. Therefore, in the present study,
Ti-15Mo was alloyed with 0.8 wt.-% of the rare earth metals
lanthanum (Ti-15Mo+0.8La) and neodymium (Ti-15Mo+0.8Nd) to
improve its machinability. Their microstructure consisted of a
titanium matrix and micrometer-size particles of the rare earth metals
and two of their oxides. The particles stabilized the microstructure as
grain growth was minimized. As especially the ductility might be
affected by the precipitates, the behavior of Ti-15Mo+0.8La and Ti-
15Mo+0.8Nd was investigated during static and dynamic
deformation at elevated temperature to develop a processing route.
The resulting mechanical properties (static strength and ductility)
were similar in all investigated alloys.
Abstract: In the present work, the effect of load and sliding
distance on the performance tribology of commercially used
aluminium-silicon engine block and piston was evaluated at ambient
conditions with humidity of 80% under dry sliding conditions using a
pin-on-disc with two different loads of 5N and 20N yielding applied
pressure of 0.30MPa and 1.4MPa, respectively, at sliding velocity of
0.29ms-1 and with varying sliding distance ranging from 260m-
4200m. Factors and conditions that had significant effect were
identified. The results showed that the load and the sliding distance
affect the wear rate of the alloys and the wear rate increased with
increasing load for both the alloys. Wear rate also increases almost
linearly at low loads and increase to a maximum then attain a plateau
with increasing sliding distance. For both applied loads the piston
alloy showed the better performance due to higher Ni and Mg
content. The worn surface and wear debris was characterized by
optical microscope, SEM and EDX analyzer. The worn surface was
characterized by surface with shallow grooves at loads while the
groove width and depth increased as the loads increases. Oxidative
wear was found to be the predominant mechanisms in the dry sliding
of Al-Si alloys at low loads.
Abstract: The aim of the paper was to elaborate a novel calculator BasWilCalc, that allows to estimate the actual amount of biomass on the basket willow plantations. The proposed method is based on the results of field experiment conducted during years 2011-2013 on basket willow plantation in the south-western part of Poland. As input data the results of destructive measurements of the diameter, length and weight of willow stems and non-destructive biometric measurements of diameter in the middle of stems and their length during the growing season performed at weekly intervals were used. Performed analysis enabled to develop the algorithm which, due to the fact that energy plantations are of known and constant planting structure, allows to estimate the actual amount of willow basket biomass on the plantation with a given probability and accuracy specified by the model, based on the number of stems measured and the age of the plantation.
Abstract: The mathematical analysis on radiation obtained and
the development of the solar photovoltaic (PV) array groundwater
pumping is needed in the rural areas of Thohoyandou for sizing and
power performance subject to the climate conditions within the area.
A simple methodology approach is developed for the directed
coupled solar, controller and submersible ground water pump system.
The system consists of a PV array, pump controller and submerged
pump, battery backup and charger controller. For this reason, the
theoretical solar radiation is obtained for optimal predictions and
system performance in order to achieve different design and
operating parameters. Here the examination of the PV schematic
module in a Direct Current (DC) application is used for obtainable
maximum solar power energy for water pumping. In this paper, a
simple efficient photovoltaic water pumping system is presented with
its theoretical studies and mathematical modeling of photovoltaics
(PV) system.
Abstract: This paper is about method to produce a stable and
accurate constant output pulse width regardless of the amplitude,
period and pulse width variation of the input signal source. The pulse
generated is usually being used in numerous applications as the
reference input source to other circuits in the system. Therefore, it is
crucial to produce a clean and constant pulse width to make sure the
system is working accurately as expected.
Abstract: Calcium phosphate coating (CaP) has been employed
for protein delivery, but the typical direct protein adsorption on the
coating led to low incorporation content and fast release of the
protein from the coating. By using bovine serum albumin (BSA) as a
model protein, rapid biomimetic co-precipitation between calcium
phosphate and BSA was employed to control the distribution of BSA
within calcium phosphate coating during biomimetic formation on
titanium surface for only 6 h at 50oC in an accelerated calcium
phosphate solution. As a result, the amount of BSA incorporation and
release duration could be increased by using a rapid biomimetic coprecipitation
technique. Up to 43 fold increases in the BSA
incorporation content and the increase from 6 h to more than 360 h in
release duration compared to typical direct adsorption technique were
observed depending on the initial BSA concentration used during coprecipitation
(1, 10 and 100 μg.ml-1). From x-ray diffraction and
Fourier transform infrared spectroscopy studies, the coating
composition was not altered with the incorporation of BSA by this
rapid biomimetic co-precipitation and mainly comprised octacalcium
phosphate and hydroxyapatite. However, the microstructure of
calcium phosphate crystals changed from straight, plate-like units to
curved, plate-like units with increasing BSA content.
Abstract: To mimic the natural circumstances of cell growth in an organism, we present three-dimensional (3D) scaffolds fabricated by microfluidics for cultivation. This work investigates the cellular behaviors of rat cardiomyocytes in gelatin 3D scaffolds compared to those on 2D control, such as proliferation, viability and morphology. We found that the scaffolds may induce skeletal differentiation of H9c2 cells.
Abstract: In Capitalism all economic activity rests upon a set of
core institutional foundations, main from which are privately owned
capital assets and profit. How these core institutional foundations are
working in former soviet countries, in particular in Travel and
Tourism Industry of Georgia?
The role of Travel and Tourism as a key pillar of economic growth
is being increasingly recognized by governments in all regions of the
world. For the last few years Georgia succeeded in the World Bank
and IFC “Doing Business” rankings. Despite of that, during decades
totally different statistical data of the tourism sector were provided by
the different State bodies; economic parameters were published few,
or not published at all.
The frequency and extent of property rights violation in Georgia
has repeatedly been the subject of concern for the last decade. Total
value of abrogated by the former Georgian Government private
property is estimated approximately in US$4-5 billion.
Thus, if economic profitability is unknown and property rights are
not protected – that means that the main institutional foundations of
capitalism in Georgia, are not working properly yet, that cause
management problems at all levels of the national Travel and
Tourism industry of Georgia.
Abstract: The purpose of this research is to study of consumer
perception and understanding consumer buying behavior that related
between satisfied and factors affecting the purchasing. Methodology
can be classified between qualitative and quantitative approaches for
the qualitative research were interviews from middlemen who bought
organic vegetables, and middlemen related to production and
marketing system. A questionnaire was utilized as a tool to collect
data. Statistics utilized in this research included frequency,
percentage, mean, standard deviation, and multiple regression
analysis. The result show the reason to decision buying motives is
Fresh products of organic vegetables is the most significant factor on
individuals’ income, with a b of –.143, t = –2.470, the price of
organic vegetables is the most significant factor on individuals’
income, with a b of .176, t = 2.561, p value = .011. The results show
that most people with higher income think about the organic products
are expensive and have negative attitudes towards organic vegetable
as individuals with low and medium income level. Therefore,
household income had a significant influence on the purchasing
decision.
Abstract: The purpose of this research was to identify factors
that influenced the success of e-commerce implementation within
SMEs businesses. In order to achieve the objectives of this research,
the researcher collected data from random firms in Thailand, both the
users and those who are not using the e-commerce. The data was
comprised of the results of 310 questionnaires, as well as 10
interviews with owner/managers of businesses who are currently
using e-commerce successfully. The data were analyzed by using
descriptive statistics, which included frequency, percentages, mean,
and the standard deviation of pertinent factors. Independent t-test and
one-way ANOVA test were also used. The findings of this research
revealed that 50% of all the firms surveyed had e-commerce website,
whereas, over 20% of all firms surveyed had developing an ecommerce
strategy. The result findings also indicate that
organizational factors, technological factors and environment factors
as significant factors effecting success of e-commerce
implementation in SMEs. From the hypotheses testing, the findings
revealed that the different level of support use ecommerce by
owner/manager had different success in e-commerce implementation.
Moreover, the difference in e-commerce management approach
affected the success in terms of higher total sales for the business or
higher number of retained or returning customers.
Abstract: The success of any retail business is predisposed by its
swift response and its knack in understanding the constraints and the
requirements of customers. In this paper a conceptual design model
of an automated customer-friendly supermarket has been proposed.
In this model a 10-sided, space benefited, regular polygon shaped
gravity shelves have been designed for goods storage and effective
customer-specific algorithms have been built-in for quick automatic
delivery of the randomly listed goods. The algorithm is developed
with two main objectives, viz., delivery time and priority. For
meeting these objectives the randomly listed items are reorganized
according to the critical-path of the robotic arm specific to the
identified shop and its layout and the items are categorized according
to the demand, shape, size, similarity and nature of the product for an
efficient pick-up, packing and delivery process. We conjectured that
the proposed automated supermarket model reduces business
operating costs with much customer satisfaction warranting a winwin
situation.