Abstract: A wireless sensor network (WSN) is a collection of
sensor nodes organized into a cooperative network. These nodes
communicate through a wireless antenna. Reduction in physical size
and multiband operation is an important requirement of WSN
antenna. Fractal antenna is used for miniaturization and multiband
operation. The self-similar or self-affine and space filling property of
fractal geometry increases the effective electrical length of the
antenna, reduces the size and make them frequency independent. This
paper elaborates on Dual band fractal antenna with Coplanar
Waveguide (CPW) feed for WSN. The proposed antenna is designed
on a FR4 substrate with the dimension of 27mm x 28.5mm x 1.6mm,
resonates at 2.4GHz and 5.2GHz with a return loss less than -10dB.
The design and simulation process is carried out using IE3D
simulation software. The simulated and measured results are found in
good agreement.
Abstract: This research focuses on the optimization of glazed
surfaces and the assessment of possible solar gains in industrial
buildings. Existing window rating methods for single windows were
evaluated and a new method for a simple analysis of energy gains and
losses by single windows was introduced. Furthermore extensive
transient building simulations were carried out to appraise the
performance of low cost polycarbonate multi-cell sheets in
interaction with typical buildings for industrial applications. Mainly
energy saving potential was determined by optimizing the orientation
and area of such glazing systems in dependency on their thermal
qualities. Moreover the impact on critical aspects such as summer
overheating and daylight illumination was considered to ensure the
user comfort and avoid additional energy demand for lighting or
cooling. Hereby the simulated heating demand could be reduced by
up to 1/3 compared to traditional architecture of industrial halls using
mainly skylights.
Abstract: Novel bio-based polymer electrolyte was synthesized
with LiClO4 as the main source of charge carrier. Initially,
polyurethane-LiClO4 polymer electrolytes were synthesized via
prepolymerization method with different NCO/OH ratios and labelled
them as PU1, PU2, PU3 and PU4. Fourier transform infrared (FTIR)
analysis indicates the co-ordination between Li+ ion and polyurethane
in PU1. Differential scanning calorimetry (DSC) analysis indicates
PU1 has the highest glass transition temperature (Tg) corresponds to
the most abundant urethane group which is the hard segment in PU1.
Scanning electron microscopy (SEM) shows the good miscibility
between lithium salt and the polymer. The study found that PU1
possessed the greatest ionic conductivity and the lowest activation
energy, Ea. All the polyurethanes exhibited linear Arrhenius
variations indicating ion transport via simple lithium ion hopping in
polyurethane. This research proves the NCO content in polyurethane
plays an important role in affecting the ionic conductivity of this
polymer electrolyte.
Abstract: The effect of trucks on the level of service is
determined by considering passenger car equivalents (PCE) of trucks.
The current version of Highway Capacity Manual (HCM) uses a
single PCE value for all tucks combined. However, the composition
of truck traffic varies from location to location; therefore, a single
PCE value for all trucks may not correctly represent the impact of
truck traffic at specific locations. Consequently, present study
developed separate PCE values for single-unit and combination
trucks to replace the single value provided in the HCM on different
freeways. Site specific PCE values, were developed using concept of
spatial lagging headways (that is the distance between rear bumpers
of two vehicles in a traffic stream) measured from field traffic data.
The study used data from four locations on a single urban freeway
and three different rural freeways in Indiana. Three-stage-leastsquares
(3SLS) regression techniques were used to generate models
that predicted lagging headways for passenger cars, single unit trucks
(SUT), and combination trucks (CT). The estimated PCE values for
single-unit and combination truck for basic urban freeways (level
terrain) were: 1.35 and 1.60, respectively. For rural freeways the
estimated PCE values for single-unit and combination truck were:
1.30 and 1.45, respectively. As expected, traffic variables such as
vehicle flow rates and speed have significant impacts on vehicle
headways. Study results revealed that the use of separate PCE values
for different truck classes can have significant influence on the LOS
estimation.
Abstract: Theoretical optimization of a copper-water negative
inclination heat pipe with internal composite wick structure had been
performed, regarding a new introduced parameter: the ratio between
the coarse mesh wraps and the fine mesh wraps of the composite
wick. Since in many cases, the design of a heat pipe matches specific
thermal requirements and physical limitations, this work
demonstrates the optimization of a 1m length, 8mm internal diameter
heat pipe without an adiabatic section, at a negative inclination angle
of -10º. The optimization is based on a new introduced parameter, LR:
the ratio between the coarse mesh wraps and the fine mesh wraps.
Abstract: In the present work, the effects of additives, including
contents of the added antioxidants and type of the selected metallic
stearates (either calcium stearate (CaSt) or zinc stearate (ZnSt)), on
the thermal stabilities of carbon black (CB)/high density polyethylene
(HDPE) compounds were studied. The results showed that the AO
contents played a key role in the thermal stabilities of the CB/HDPE
compounds — the higher the AO content, the higher the thermal
stabilities. Although the CaSt-containing compounds were slightly
superior to those with ZnSt in terms of the thermal stabilities, the
remaining solid residue of CaSt after heated to the temperature of 600
°C (mainly calcium carbonate (CaCO3) as characterized by the X-ray
diffraction (XRD) technique) seemed to catalyze the decomposition
of CB in the HDPE-based compounds. Hence, the quantification of
CB in the CaSt-containing compounds with a muffle furnace gave an
inaccurate CB content — much lower than actual value. However,
this phenomenon was negligible in the ZnSt-containing system.
Abstract: Polyethylene (PE), Polypropylene (PP), Polyethylene
(vinyl acetate) (EVA) and PE-ionomer nanocomposite samples were
prepared by mixing of the polymer with organofilized
montmorillonite fillers Cloisite 93A and Dellite 67G. The amount of
each modified montmorillonite (MMT) was fixed to 5% (w/w). The
twin-screw kneader was used for the compounding of polymer matrix
and chosen nanofillers. The level of MMT exfoliation was studied by
the transmission electron microscopy (TEM) observations. The
mechanical properties of prepared materials were evaluated by
dynamical mechanical analysis at 30°C and by the measurement of
tensile properties (stress and strain at break).
Abstract: OEE has been used in many industries as measure of
performance. However due to limitations of original OEE, it has been
modified by various researchers. OEE for mining application is
special version of classic equation, carries these limitation over. In
this paper it has been aimed to modify the OEE for mining
application by introducing the weights to the elements of it and
termed as Mine Production index (MPi). As a special application of
new index MPishovel has been developed by authors. This can be used
for evaluating the shovel effectiveness. Based on analysis, utilization
followed by performance and availability were ranked in this order.
To check the applicability of this index, a case study was done on
four electrical and one hydraulic shovel in a Swedish mine. The
results shows that MPishovel can evaluate production effectiveness of
shovels and can determine effectiveness values in optimistic view
compared to OEE. MPi with calculation not only give the
effectiveness but also can predict which elements should be focused
for improving the productivity.
Abstract: Information and Communication Technologies (ICTs)
are pervasive nowadays, including in education where they are
expected to improve the performance of learners. However, the hope
placed in ICTs to find viable solutions to the problem of poor
academic performance in schools in the developing world has not yet
yielded the expected benefits. This problem serves as a motivation to
this study whose aim is to examine the perceptions of educators on
the advantages and disadvantages of e-learning. This aim will be
subdivided into two types of research objectives. Objectives on the
identification and design of theories and models will be achieved
using content analysis and literature review. However, the objective
on the empirical testing of such theories and models will be achieved
through the survey of educators from different schools in the
Pinetown District of the South African Kwazulu-Natal province.
SPSS is used to quantitatively analyse the data collected by the
questionnaire of this survey using descriptive statistics and Pearson
correlations after assessing the validity and the reliability of the data.
The main hypothesis driving this study is that there is a relationship
between the demographics of educators’ and their adherence to
learning theories on one side, and their perceptions on the advantages
and disadvantages of e-learning on the other side, as argued by
existing research; but this research views these learning theories
under three perspectives: educators’ adherence to self-regulated
learning, to constructivism, and to progressivism. This hypothesis
was fully confirmed by the empirical study except for the
demographic factor where teachers’ level of education was found to
be the only demographic factor affecting the perceptions of educators
on the advantages and disadvantages of e-learning.
Abstract: This paper presents a new method to design nonlinear
feedback linearization controller for PEMFCs (Polymer Electrolyte
Membrane Fuel Cells). A nonlinear controller is designed based on
nonlinear model to prolong the stack life of PEMFCs. Since it is
known that large deviations between hydrogen and oxygen partial
pressures can cause severe membrane damage in the fuel cell,
feedback linearization is applied to the PEMFC system so that the
deviation can be kept as small as possible during disturbances or load
variations. To obtain an accurate feedback linearization controller,
tuning the linear parameters are always important. So in proposed
study NSGA (Non-Dominated Sorting Genetic Algorithm)-II method
was used to tune the designed controller in aim to decrease the
controller tracking error. The simulation result showed that the
proposed method tuned the controller efficiently.
Abstract: The effect of Zn2+, Mg2+, and Ba2+ on Saccharomyces
pastorianus performance was evaluated in this study at independent
and three variable combinations. After 96 h of fermentation, high
wort fermentability (%F) = 29.53 was obtained in medium containing
900:4 ppm Mg2+ + Ba2+. Increased ethanol yield 7.35 %(v/v) and
7.13 %(v/v) were obtained in media containing 900:4 ppm Mg2+ +
Ba2+ and 12:900 ppm Zn2+ + Mg2+. Decrease %F = 22.54 and ethanol
yield 6.18 % (v/v) was obtained in medium containing 12:4 ppm Zn2+
+ Ba2+. In media containing the individual ions, increased %F =
27.94 and 26.03 were recorded for media containing 700 ppm Mg2+
and 2 ppm Ba2+ , with ethanol yield of 7.88% (v/v) and 7.62% (v/v)
respectively. Reduced %F and ethanol yield was observed for 10 ppm
Zn2+ and 4 ppm Ba2+ media. The impact of Ba2+ at 1 and 2 ppm was
significant.
Abstract: This study was conducted to evaluate the manganese
removal from aqueous solution using Banana peels activated carbon
(BPAC). Batch experiments have been carried out to determine the
influence of parameters such as pH, biosorbent dose, initial metal ion
concentrations and contact times on the biosorption process. From
these investigations, a significant increase in percentage removal of
manganese 97.4% is observed at pH value 5.0, biosorbent dose 0.8 g,
initial concentration 20 ppm, temperature 25 ± 2°C, stirring rate 200
rpm and contact time 2h. The equilibrium concentration and the
adsorption capacity at equilibrium of the experimental results were
fitted to the Langmuir and Freundlich isotherm models; the Langmuir
isotherm was found to well represent the measured adsorption data
implying BPAC had heterogeneous surface. A raw groundwater
samples were collected from Baharmos groundwater treatment plant
network at Embaba and Manshiet Elkanater City/District-Giza,
Egypt, for treatment at the best conditions that reached at first phase
by BPAC. The treatment with BPAC could reduce iron and
manganese value of raw groundwater by 91.4% and 97.1%,
respectively and the effect of the treatment process on the
microbiological properties of groundwater sample showed decrease
of total bacterial count either at 22°C or at 37°C to 85.7% and 82.4%,
respectively. Also, BPAC was characterized using SEM and FTIR
spectroscopy.
Abstract: The effect of particle size on shear strength of
granular materials are investigated using direct shear tests. Small
direct shear test (60 mm by 60 mm by 24 mm deep) were conducted
for particles passing the sieves with opening size of 2.36 mm.
Meanwhile, particles passing the standard 20 mm sieves were tested
using large direct shear test (300 mm by 300 mm by 200 mm deep).
The large direct shear tests and the small direct shear tests carried out
using the same shearing rate of 0.09 mm/min and similar normal
stresses of 100, 200 and 300 kPa. The results show that the peak and
residual shear strength increases as particle size increases.
Abstract: This paper focuses on the presentation of results
which were obtained as a part of the project FR-TI 3/742: “System of
Lightweight Materials for Finishing of Buildings with Waste Raw
Materials”. Attention was paid to the light weighting of polymermodified
mortars applicable as adhesives, screeds and repair mortars.
In terms of repair mortars, they were ones intended for the sanitation
of aerated concrete.
Abstract: One- and two-dimensional carbon nanostructures with
sp2 hybridization of carbon atoms (single walled carbon nanotubes
and graphene) are promising materials in future electronic and
spintronics devices due to specific character of their electronic
structure. In this paper we present a comparative study of graphene
and single-wall carbon nanotubes by Raman spectro-microscopy in
strong magnetic field. This unique method allows to study changes in
electronic band structure of the two types of carbon nanostructures
induced by a strong magnetic field.
Abstract: WiMAX is a telecommunications technology and it is
specified by the Institute of Electrical and Electronics Engineers Inc.,
as the IEEE 802.16 standard. The goal of this technology is to
provide a wireless data over long distances in a variety of ways. IEEE
802.16 is a recent standard for mobile communication. In this paper,
we provide an overview of various key management algorithms to
provide security for WiMAX.
Abstract: This paper presents a hybrid three phase rectifier for
high power factor application. This rectifier is composed by zero
voltage transition (ZVT) and zero current transition (ZCT) boost
converter with three phase diode bridge rectifier, in parallel with a six
pulse three phase pulse width modulation (PWM) controlled rectifier.
The proposed topology is capable of high power factor with DC
output voltage regulation by providing sinusoidal input. Also, it
increases the overall efficiency of the new hybrid rectifier to 94.56%
and the total harmonic distortion of the hybrid structure varies from
0% to 16% at nominal output power. This topology was simulated in
MATLAB/SIMULINK environment and the output waveforms
presented with experimental result.
Abstract: The objective of the study was to select the survival of
probiotic strains when exposed to acidic and bile salts condition. Four
probiotic strains Lactobacillus casei subsp. rhamnosus TISTR 047,
Lactobacillus casei TISTR 1500, Lactobacillus acidophilus TISTR
1338 and Lactobacillus plantarum TISTR 1465 were cultured in
MRS broth and incubated at 35ºC for 15 hours before being inoculated
into acidic condition 5 M HCl, pH 2 for 2 hours and bile salt 0.3%,
pH 5.8 for 8 hour. The survived probiotics were counted in MRS agar.
Among four stains, Lactobacillus casei subsp. rhamnosus TISTR 047
was the highest tolerance specie. Lactobacillus casei subsp.
rhamnosus TISTR 047 reduced 6.74±0.07 log CFU/ml after growing
in acid and 5.52±0.05 log CFU/ml after growing in bile salt. Then,
double emulsion of microorganisms was chosen to encapsulate before
spray drying. Spray drying was done with the inlet temperature 170ºC
and outlet temperature 80ºC. The results showed that the survival of
encapsulated Lactobacillus casei subsp. rhamnosus TISTR 047 after
spray drying decreased from 9.63 ± 0.32 to 8.31 ± 0.11 log CFU/ml
comparing with non-encapsulated, 9.63 ± 0.32 to 4.06 ± 0.08 log
CFU/ml. Therefore, Lactobacillus casei subsp. rhamnosus TISTR 047
would be able to survive in gastrointestinal and spray drying condition.
Abstract: Advances technology in the field of photogrammetry
replaces analog cameras with reflection on aircraft GPS/IMU system
with a digital aerial camera. In this system, when determining the
position of the camera with the GPS, camera rotations are also
determined by the IMU systems. All around the world, digital aerial
cameras have been used for the photogrammetry applications in the
last ten years. In this way, in terms of the work done in
photogrammetry it is possible to use time effectively, costs to be
reduced to a minimum level, the opportunity to make fast and
accurate.
Geo-referencing techniques that are the cornerstone of the GPS /
INS systems, photogrammetric triangulation of images required for
balancing (interior and exterior orientation) brings flexibility to the
process. Also geo-referencing process; needed in the application of
photogrammetry targets to help to reduce the number of ground
control points. In this study, the use of direct and indirect georeferencing
techniques on the accuracy of the points was investigated
in the production of photogrammetric mapping.
Abstract: Persea declinata (Bl.) Kosterm is a member of the
Lauraceae family, widely distributed in Southeast Asia. It is from the
same genus with avocado (Persea americana Mill), which is widely
consumed as food and for medicinal purposes. In the present study,
we examined the anticancer properties of Persea declinata (Bl.)
Kosterm bark methanolic crude extract (PDM). PDM exhibited a
potent antiproliferative effect in MCF-7 human breast cancer cells,
with an IC50 value of 16.68 .g/mL after 48h of treatment. We
observed that PDM caused cell cycle arrest and subsequent apoptosis
in MCF-7 cells, as exhibited by increased population at G0/G1 phase,
higher lactate dehydrogenase (LDH) release, and DNA
fragmentation. Mechanistic studies showed that PDM caused
significant elevation in ROS production, leading to perturbation of
mitochondrial membrane potential, cell permeability, and activation
of caspases-3/7. On the other hand, real-time PCR and Western blot
analysis showed that PDM treatment increased the expression of the
proapoptotic molecule, Bax, but decreased the expression of
prosurvival proteins, Bcl-2 and Bcl-xL, in a dose-dependent manner.
These findings imply that PDM could inhibit proliferation in MCF-7
cells via cell cycle arrest and apoptosis induction, indicating its
potential as a therapeutic agent worthy of further development.