Abstract: Heat transfer from two cam shape cylinder in tandem
arrangement had been studied numerically.
The distance between the centers of cylinders (L) is allowed to
vary to change the longitudinal pitch ratio (L/Deq). The equivalent
diameter of the cylinder (Deq) is 27.6 mm and longitudinal pitch ratio
varies in range 2
Abstract: The research investigates the effects of super plasticizer and molarity of sodium hydroxide alkaline solution on the workability, microstructure and compressive strength of self compacting geopolymer concrete (SCGC). SCGC is an improved way of concreting execution that does not require compaction and is made by complete elimination of ordinary Portland cement content. The parameters studied were superplasticizer (SP) dosage and molarity of NaOH solution. SCGC were synthesized from low calcium fly ash, activated by combinations of sodium hydroxide and sodium silicate solutions, and by incorporation of superplasticizer for self compactability. The workability properties such as filling ability, passing ability and resistance to segregation were assessed using slump flow, T-50, V-funnel, L-Box and J-ring test methods. It was found that the essential workability requirements for self compactability according to EFNARC were satisfied. Results showed that the workability and compressive strength improved with the increase in superplasticizer dosage. An increase in strength and a decrease in workability of these concrete samples were observed with the increase in molarity of NaOH solution from 8M to 14M. Improvement of interfacial transition zone (ITZ) and micro structure with the increase of SP and increase of concentration from 8M to 12M were also identified.
Abstract: Mercury is a natural occurring element and present in
various concentrations in the environment. Due to its toxic effects, it
is desirable to research mercury sensitive materials to adsorb
mercury. This paper describes the preparation of Au nanoparticles for
mercury adsorption by using a microwave (MW)-polyol method in
the presence of three different Sodium Chloride (NaCl)
concentrations (10, 20 and 30 mM). Mixtures of spherical, triangular,
octahedral, decahedral particles and 1-D product were obtained using
this rapid method. Sizes and shapes was found strongly depend on the
concentrations of NaCl. Without NaCl concentration, spherical,
triangular plates, octahedral, decahedral nanoparticles and 1D
product were produced. At the lower NaCl concentration (10 mM),
spherical, octahedral and decahedral nanoparticles were present,
while spherical and decahedral nanoparticles were preferentially form
by using 20 mM of NaCl concentration. Spherical, triangular plates,
octahedral and decahedral nanoparticles were obtained at the highest
NaCl concentration (30 mM). The amount of mercury adsorbed using
20 ppm mercury solution is the highest (67.5 %) for NaCl
concentration of 30 mM. The high yield of polygonal particles will
increase the mercury adsorption. In addition, the adsorption of
mercury is also due to the sizes of the particles. The sizes of particles
become smaller with increasing NaCl concentrations (size ranges, 5-
16 nm) than those synthesized without addition of NaCl (size ranges
11-32 nm). It is concluded that NaCl concentrations affects the
formation of sizes and shapes of Au nanoparticles thus affects the
mercury adsorption.
Abstract: New nondestructive technique, namely an inverse technique based on vibration tests, to characterize nonlinear mechanical properties of adhesive layers in sandwich composites is developed. An adhesive layer is described as a viscoelastic isotropic material with storage and loss moduli which are both frequency dependent values in wide frequency range. An optimization based on the planning of experiments and response surface technique to minimize the error functional is applied to decrease considerably the computational expenses. The developed identification technique has been tested on aluminum panels and successfully applied to characterize viscoelastic material properties of 3M damping polymer ISD-112 used as a core material in sandwich panels.
Abstract: The deficit of power for electricity demand reaches
almost 30% for consumers in the last few years. This reflects with
continually increasing the price of electricity, and today the price for
small industry is almost 110Euro/MWh. The high price is additional
problem for the owners in the economy crisis which is reflected with
higher price of the goods.
The paper gives analyses of the energy needs for real agro
complex in Macedonia, private vinery with capacity of over 2 million
liters in a year and with self grapes and fruits fields. The existing
power supply is from grid with 10/04 kV transformer. The
geographical and meteorological condition of the vinery location
gives opportunity for including renewable as a power supply option
for the vinery complex.
After observation of the monthly energy needs for the vinery, the
base scenario is the existing power supply from the distribution grid.
The electricity bill in small industry has three factors: electricity in
high and low tariffs in kWh and the power engaged for the
technological process of production in kW. These three factors make
the total electricity bill and it is over 110 Euro/MWh which is the
price near competitive for renewable option. On the other side
investments in renewable (especially photovoltaic (PV)) has tendency
of decreasing with price of near 1,5 Euro/W. This means that
renewable with PV can be real option for power supply for small
industry capacities (under 500kW installed power).
Therefore, the other scenarios give the option with PV and the last
one includes wind option. The paper presents some scenarios for
power supply of the vinery as the followings:
• Base scenario of existing conventional power supply from the
grid
• Scenario with implementation of renewable of Photovoltaic
• Scenario with implementation of renewable of Photovoltaic and
Wind power
The total power installed in a vinery is near 570 kW, but the
maximum needs are around 250kW. At the end of the full paper some
of the results from scenarios will be presented. The paper also
includes the environmental impacts of the renewable scenarios, as
well as financial needs for investments and revenues from renewable.
Abstract: An experiment was conducted to determine the effect
of the rearing system on growth performance, carcass yield,
hematological parameters, and feather pecking damage of Thai
indigenous chickens. Three hundred and sixty 1-d-old chicks were
randomly assigned to 2 treatments: indoor treatment and outdoor
access treatment. In the indoor treatment, the chickens were housed
in floor pens (5 birds/m2). In the outdoor access treatment, the
chickens were housed in a similar indoor house; in addition, they also
had an outdoor grass paddock (1 bird/m2). All birds were provided
with same diet and were raised for 16 wk of age. The results showed
that growth performance and carcass yield were not different among
treatment (P>0.05). Outdoor access had no effect on hematological
parameters (P>0.05). However, the feather pecking damage of the
chickens in the outdoor access treatment was lower than that of the
chickens in the indoor treatment (P
Abstract: This paper presents a new ultra-wideband (UWB) bandpass filter (BPF) with sharp roll-off and dual-notched bands. The filter consists of a triangle ring multi-mode resonator (MMR) with the stub-loaded resonator (SLR) for controlling the two transmission zeros at 2.8 / 11 GHz, the embedded open-circuited stub and the asymmetric tight coupled input/output (I/O) lines for introducing the dual notched bands at 5.2 / 6.8 GHz. The attenuation slope in the lower and higher passband edges of the proposed filter show 160- and 153-dB/GHz, respectively. This study mainly provides a simple method to design a UWB bandpass filter with high passband selectivity and dual-notched bands for satisfying the Federal Communications Commission (FCC-defined) indoor UWB specification
Abstract: The concept of e-Learning is now emerging in Sub Saharan African countries like Tanzania. Due to economic constraints and other social and cultural factors faced by these countries, the use of Information and Communication Technology (ICT) is increasing at a very low pace. The digital divide threat has propelled the Government of Tanzania to put in place the national ICT Policy in 2003 which defines the direction of all ICT activities nationally. Among the main focused areas is the use of ICT in education, since for the development of any country, there is a need of creating knowledge based society. This paper discusses the initiatives made so far to introduce the use of ICT tools to some secondary schools using open source software in e-content development to facilitate a self-learning environment
Abstract: A steady two-phase flow model has been developed to simulate the drying process of porous particle in a pneumatic conveying dryer. The model takes into account the momentum, heat and mass transfer between the continuous phase and the dispersed phase. A single particle model was employed to calculate the evaporation rate. In this model the pore structure is simplified to allow the dominant evaporation mechanism to be readily identified at all points within the duct. The predominant mechanism at any time depends upon the pressure, temperature and the diameter of pore from which evaporating is occurring. The model was validated against experimental studies of pneumatic transport at low and high speeds as well as pneumatic drying. The effects of operating conditions on the dryer parameters are studied numerically. The present results show that the drying rate is enhanced as the inlet gas temperature and the gas flow rate increase and as the solid mass flow rate deceases. The present results also demonstrate the necessity of measuring the inlet gas velocity or the solid concentration in any experimental analysis.
Abstract: Continuously growing needs for Internet applications
that transmit massive amount of data have led to the emergence of
high speed network. Data transfer must take place without any
congestion and hence feedback parameters must be transferred from
the receiver end to the sender end so as to restrict the sending rate in
order to avoid congestion. Even though TCP tries to avoid
congestion by restricting the sending rate and window size, it never
announces the sender about the capacity of the data to be sent and
also it reduces the window size by half at the time of congestion
therefore resulting in the decrease of throughput, low utilization of
the bandwidth and maximum delay. In this paper, XCP protocol is
used and feedback parameters are calculated based on arrival rate,
service rate, traffic rate and queue size and hence the receiver
informs the sender about the throughput, capacity of the data to be
sent and window size adjustment, resulting in no drastic decrease in
window size, better increase in sending rate because of which there is
a continuous flow of data without congestion. Therefore as a result of
this, there is a maximum increase in throughput, high utilization of
the bandwidth and minimum delay. The result of the proposed work
is presented as a graph based on throughput, delay and window size.
Thus in this paper, XCP protocol is well illustrated and the various
parameters are thoroughly analyzed and adequately presented.
Abstract: Current mode circuits like current conveyors are
getting significant attention in current analog ICs design due to their
higher band-width, greater linearity, larger dynamic range, simpler
circuitry, lower power consumption and less chip area. The second
generation current controlled conveyor (CCCII) has the advantage of
electronic adjustability over the CCII i.e. in CCCII; adjustment of the
X-terminal intrinsic resistance via a bias current is possible. The
presented approach is based on the CMOS implementation of second
generation positive (CCCII+), negative (CCCII-) and dual Output
Current Controlled Conveyor (DOCCCII) and its application as
Universal filter. All the circuits have been designed and simulated
using 65nm CMOS technology model parameters on Cadence
Virtuoso / Spectre using 1V supply voltage. Various simulations have
been carried out to verify the linearity between output and input
ports, range of operation frequency, etc. The outcomes show good
agreement between expected and experimental results.
Abstract: Genetic Algorithms (GAs) are direct searching
methods which require little information from design space. This
characteristic beside robustness of these algorithms makes them to be
very popular in recent decades. On the other hand, while this method
is employed, there is no guarantee to achieve optimum results. This
obliged designer to run such algorithms more than one time to
achieve more reliable results. There are many attempts to modify the
algorithms to make them more efficient. In this paper, by application
of fractal dimension (particularly, Box Counting Method), the
complexity of design space are established for determination of
mutation and crossover probabilities (Pm and Pc). This methodology
is followed by a numerical example for more clarification. It is
concluded that this modification will improve efficiency of GAs and
make them to bring about more reliable results especially for design
space with higher fractal dimensions.
Abstract: Plastics occupy wide place in the applications of
automotive, electronics and house goods. Especially reinforced
plastics become popular because of their high strength besides their
advantages of low weight and easy manufacturability. In this study,
mechanical and morphological properties of polypropylene (PP) and
high density polyethylene (HDPE) matrix composites reinforced with
surface modified nano titan dioxide (TiO2) particles were
investigated. Surface modification was made by coating the nano
powders with maleic anhydride grafted styrene ethylene butylene
styrene (SEBS-g-MA) and silane, respectively. After surface
modification, PP/TiO2 and HDPE/TiO2 composites were obtained by
using twin screw extruder at titan dioxide loading of 1 wt.%, 3 wt.%
and 5 wt.%. Effects of surface modification were determined by
thermal and morphological analysis. SEBS-g-MA provided bridging
effect between TiO2 particles and polymer matrix while silane was
effective as a dispersant. Depending on that, homogenous structures
without agglomeration were obtained. Mechanical tests were
performed on the injection moldings of the composites for obtaining
the impact strength, tensile strength, stress at break, elongation and
elastic modulus. Reinforced HDPE and PP moldings gave higher
tensile strength and elastic modulus due to the rigid structure of TiO2.
Slight increment was seen in stress at break. Elongation and impact
strength decreased due to the stiffness of the nano titan dioxide.
Abstract: This research is to design and implement a new kind
of agitators called differential agitator. The Differential Agitator is an
electro- mechanic set consists of two shafts. The first shaft is the
bearing axis while the second shaft is the axis of the quartet upper
bearing impellers group and the triple lower group which are called
as agitating group. The agitating group is located inside a cylindrical
container equipped especially to contain square directors for the
liquid entrance and square directors called fixing group for the liquid
exit. The fixing group is installed containing the agitating group
inside any tank whether from upper or lower position. The agitating
process occurs through the agitating group bearing causing a lower
pressure over the upper group leading to withdrawing the liquid from
the square directors of the liquid entering and consequently the liquid
moves to the denser place under the quartet upper group. Then, the
liquid moves to the so high pressure area under the agitating group
causing the liquid to exit from the square directors in the bottom of
the container. For improving efficiency, parametric study and shape
optimization has been carried out. A numerical analysis,
manufacturing and laboratory experiments were conducted to design
and implement the differential agitator. Knowing the material
prosperities and the loading conditions, the FEM using ANSYS11
was used to get the optimum design of the geometrical parameters of
the differential agitator elements while the experimental test was
performed to validate the advantages of the differential agitators to
give a high agitation performance of lime in the water as an example.
In addition, the experimental work has been done to express the
internal container shape in the agitation efficiency. The study ended
up with conclusions to maximize agitator performance and optimize
the geometrical parameters to be used for manufacturing the
differential agitator
Abstract: Commercial infrastructures intended for use as leisure
retreats such as golf and ski resorts have been extensively developed in many rural areas of Japan. However, following the burst of the economic bubble in the 1990s, several existing resorts faced tough
management decisions and some were forced to close their business.
In this study, six alternative management options for restructuring the
existing golf courses (park, cemetery, biofuel production, reforestation,
pasturing and abandonment) are examined and their environmental
and economic impacts are quantitatively assessed. In addition,
restructuring scenarios of these options and an ex-ante assessment
model are developed. The scenario analysis by Monte Carlo simulation shows a clear trade-off between GHG savings and benefit/cost (B/C) ratios, of which “Restoring Nature" scenario
absorbs the most CO2 among the four scenarios considered, but its B/C
ratio is the lowest. This study can be used to select or examine options
and scenarios of golf course management and rural environmental
management policies.
Abstract: In this paper, we focus on the fusion of images from
different sources using multiresolution wavelet transforms. Based on
reviews of popular image fusion techniques used in data analysis,
different pixel and energy based methods are experimented. A novel
architecture with a hybrid algorithm is proposed which applies pixel
based maximum selection rule to low frequency approximations and
filter mask based fusion to high frequency details of wavelet
decomposition. The key feature of hybrid architecture is the
combination of advantages of pixel and region based fusion in a
single image which can help the development of sophisticated
algorithms enhancing the edges and structural details. A Graphical
User Interface is developed for image fusion to make the research
outcomes available to the end user. To utilize GUI capabilities for
medical, industrial and commercial activities without MATLAB
installation, a standalone executable application is also developed
using Matlab Compiler Runtime.
Abstract: The optical properties of InGaN/GaN laser diode based on quaternary alloys stopper and superlattice layers are numerically studied using ISE TCAD (Integrated System Engineering) simulation program. Improvements in laser optical performance have been achieved using quaternary alloy as superlattice layers in InGaN/GaN laser diodes. Lower threshold current of 18 mA and higher output power and slope efficiency of 22 mW and 1.6 W/A, respectively, at room temperature have been obtained. The laser structure with InAlGaN quaternary alloys as an electron blocking layer was found to provide better laser performance compared with the ternary AlxGa1-xN blocking layer.
Abstract: This paper argues that increased uncertainty, in certain
situations, may actually encourage investment. Since earlier studies
mostly base their arguments on the assumption of geometric Brownian
motion, the study extends the assumption to alternative stochastic
processes, such as mixed diffusion-jump, mean-reverting process, and
jump amplitude process. A general approach of Monte Carlo
simulation is developed to derive optimal investment trigger for the
situation that the closed-form solution could not be readily obtained
under the assumption of alternative process. The main finding is that
the overall effect of uncertainty on investment is interpreted by the
probability of investing, and the relationship appears to be an invested
U-shaped curve between uncertainty and investment. The implication
is that uncertainty does not always discourage investment even under
several sources of uncertainty. Furthermore, high-risk projects are not
always dominated by low-risk projects because the high-risk projects
may have a positive realization effect on encouraging investment.
Abstract: This paper attempts to discuss the evolution of the
retrieval techniques focusing on development, challenges and trends
of the image retrieval. It highlights both the already addressed and
outstanding issues. The explosive growth of image data leads to the
need of research and development of Image Retrieval. However,
Image retrieval researches are moving from keyword, to low level
features and to semantic features. Drive towards semantic features is
due to the problem of the keywords which can be very subjective and
time consuming while low level features cannot always describe high
level concepts in the users- mind.
Abstract: Thisresearch paper is dedicated to an actual issue in Latvia and in the whole European Union – development of the secondary materials management. The goal of this paper is to research the development of the secondary materials management in Latvia as a result to point out its main positive aspects and problems. In this research paper the author regards following issues: significance of the secondary materials management, current situation of the waste generation and utilization in Latvia comparing with other EU Member States, main problems and positive aspects of the secondary materials management in Latvia. The research author concludes that in last ten years a great work is done to develop the secondary materials market. Nevertheless following improvements are necessary: implementation of the packaging deposit system, development of the separate waste collection, increasing of the recycling capacity.