Abstract: Adsorption of a boron nitride nanotube (BNNT) was
examined toward ethylacetylene (C4H6) molecule by using density
functional theory (DFT) calculations at the B3LYP/6-31G (d) level,
and it was found that the adsorption energy (Ead) of ethylacetylene
the pristine nanotubes is about -1.60kcal/mol. But when nanotube has
been doped with Si and Al atoms, the adsorption energy of
ethylacetylene molecule was increased. Calculation showed that
when the nanotube is doping by Al, the adsorption energy is about -
24.19kcal/mol and also the amount of HOMO/LUMO energy gap
(Eg) will reduce significantly. Boron nitride nanotube is a suitable
adsorbent for ethylacetylene and can be used in separation processes
ethylacetylene. It is seem that nanotube (BNNT) is a suitable
semiconductor after doping, and the doped BNNT in the presence of
ethylacetylene an electrical signal is generating directly and therefore
can potentially be used for ethylacetylene sensors.
Abstract: In this paper cognitive radio is presented and the
spectrum overlay cognitive radio antenna system is detailed. A UWB
antenna with frequency reconfigurable characteristics is proposed.
The reconfigurability is achieved when the filter is integrated to the
feeding line of the single port overlay cognitive radio. When
activated, the filter can transform the UWB frequency response into a
reconfigurable narrowband one, which is suitable for the
communication operation of the CR system. Here single port overlay
cognitive radio antenna is designed and simulated using Ansoft High
Frequency Structure Simulator (HFSS).
Abstract: Photonic Crystal Fibers (PCFs) can be used in optical
communications as transmission lines. For this reason, the PCFs with
low confinement loss, low chromatic dispersion, and low nonlinear
effects are highly suitable transmission media. In this paper, we
introduce a new design of index-guiding nanostructured photonic
crystal fiber (IG-NPCF) with ultra-low chromatic dispersion, low
nonlinearity effects, and low confinement loss. Relatively low
dispersion is achieved in the wavelength range of 1200 to 1600nm
using the proposed design. According to the new structure of
nanostructured PCF presented in this study, the chromatic dispersion
slope is -30(ps/km.nm) and the confinement loss reaches below 10-7
dB/km. While in the wavelength range mentioned above at the same
time an effective area of more than 50.2μm2 is obtained.
Abstract: The main aim of a communication system is to
achieve maximum performance. In Cognitive Radio any user or
transceiver has ability to sense best suitable channel, while channel is
not in use. It means an unlicensed user can share the spectrum of a
licensed user without any interference. Though, the spectrum sensing
consumes a large amount of energy and it can reduce by applying
various artificial intelligent methods for determining proper spectrum
holes. It also increases the efficiency of Cognitive Radio Network
(CRN). In this survey paper we discuss the use of different learning
models and implementation of Artificial Neural Network (ANN) to
increase the learning and decision making capacity of CRN without
affecting bandwidth, cost and signal rate.
Abstract: Future flood can be predicted using the probable
maximum flood (PMF). PMF is calculated using the historical
discharge or rainfall data considering the other climatic parameters
remaining stationary. However climate is changing globally and the
key climatic variables are temperature, evaporation, rainfall and sea
level rise are likely to change. To develop scenarios to a basin or
catchment scale these important climatic variables should be
considered. Nowadays scenario based on climatic variables is more
suitable than PMF. Six scenarios were developed for a large Fitzroy
basin and presented in this paper.
Abstract: Proof of controlling crack width is a basic condition
for securing suitable performance in serviceability limit state. The
cracking in concrete can occur at any time from the casting of time to
the years after the concrete has been set in place. Most codes struggle
with offering procedure for crack width calculation. There is lack in
availability of design charts for designers to compute crack width
with ease. The focus of the study is to utilize design charts and
parametric equations in calculating crack width with minimum error.
The paper contains a simplified procedure to calculate crack width
for reinforced concrete (RC) sections subjected to bending with axial
tensile force following the guidelines of Euro code [DS EN-1992-1-1
& DS EN-1992-1-2]. Numerical examples demonstrate the
application of the suggested procedure. Comparison with parallel
analytical tools supports the validity of result and show the
percentage deviation of crack width in both the procedures. The
technique is simple, user friendly and ready to evolve for a greater
spectrum of section sizes and materials.
Abstract: Higher order ΔΣ Modulator (DSM) is basically an
unstable system. The approximate conditions for stability cannot be
used for the design of a DSM for industrial applications where risk is
involved. The existing second order, single stage, single bit, unity
feedback gain , discrete DSM cannot be used for the normalized full
range (-1 to +1) of an input signal since the DSM becomes unstable
when the input signal is above ±0.55. The stability is also not
guaranteed for input signals of amplitude less than ±0.55. In the
present paper, the above mentioned second order DSM is modified
with input signal dependent forward path gain. The proposed DSM is
suitable for industrial applications where one needs the digital
representation of the analog input signal, during each sampling
period. The proposed DSM can operate almost for the full range of
input signals (-0.95 to +0.95) without causing instability, assuming
that the second integrator output should not exceed the circuit supply
voltage, ±15 Volts.
Abstract: This paper describes a novel application of Fiber
Braggs Grating (FBG) sensors in the assessment of human postural
stability and balance on an unstable platform. In this work, FBG
sensor Stability Analyzing Device (FBGSAD) is developed for
measurement of plantar strain to assess the postural stability of
subjects on unstable platforms during different stances in eyes open
and eyes closed conditions on a rocker board. The studies are
validated by comparing the Centre of Gravity (CG) variations
measured on the lumbar vertebra of subjects using a commercial
accelerometer. The results obtained from the developed FBGSAD
depict qualitative similarities with the data recorded by commercial
accelerometer. The advantage of the FBGSAD is that it measures
simultaneously plantar strain distribution and postural stability of the
subject along with its inherent benefits like non-requirement of
energizing voltage to the sensor, electromagnetic immunity and
simple design which suits its applicability in biomechanical
applications. The developed FBGSAD can serve as a tool/yardstick to
mitigate space motion sickness, identify individuals who are
susceptible to falls and to qualify subjects for balance and stability,
which are important factors in the selection of certain unique
professionals such as aircraft pilots, astronauts, cosmonauts etc.
Abstract: Over the last few decades, oilfield service rolling
equipment has significantly increased in weight, primarily because of
emissions regulations, which require larger/heavier engines, larger
cooling systems, and emissions after-treatment systems, in some
cases, etc. Larger engines cause more vibration and shock loads,
leading to failure of electronics and control systems.
If the vibrating frequency of the engine matches the system
frequency, high resonance is observed on structural parts and mounts.
One such existing automated control equipment system comprising
wire rope mounts used for mounting computers was designed
approximately 12 years ago. This includes the use of an industrialgrade
computer to control the system operation. The original
computer had a smaller, lighter enclosure. After a few years, a newer
computer version was introduced, which was 10 lbm heavier. Some
failures of internal computer parts have been documented for cases in
which the old mounts were used. Because of the added weight, there
is a possibility of having the two brackets impact each other under
off-road conditions, which causes a high shock input to the computer
parts. This added failure mode requires validating the existing mount
design to suit the new heavy-weight computer.
This paper discusses the modal finite element method (FEM)
analysis and experimental modal analysis conducted to study the
effects of vibration on the wire rope mounts and the computer. The
existing mount was modelled in ANSYS software, and resultant
mode shapes and frequencies were obtained. The experimental modal
analysis was conducted, and actual frequency responses were
observed and recorded.
Results clearly revealed that at resonance frequency, the brackets
were colliding and potentially causing damage to computer parts. To
solve this issue, spring mounts of different stiffness were modeled in
ANSYS software, and the resonant frequency was determined.
Increasing the stiffness of the system increased the resonant
frequency zone away from the frequency window at which the engine
showed heavy vibrations or resonance. After multiple iterations in
ANSYS software, the stiffness of the spring mount was finalized,
which was again experimentally validated.
Abstract: The exact theoretical expression describing the
probability distribution of nonlinear sea-surface elevations derived
from the second-order narrowband model has a cumbersome form
that requires numerical computations, not well-disposed to theoretical
or practical applications. Here, the same narrowband model is reexamined
to develop a simpler closed-form approximation suitable
for theoretical and practical applications. The salient features of the
approximate form are explored, and its relative validity is verified
with comparisons to other readily available approximations, and
oceanic data.
Abstract: E-learning has become an efficient and widespread
means of education at all levels of human activities. Statistics is no
exception. Unfortunately the main focus in statistics teaching is
usually paid to the substitution in formulas. Suitable websites can
simplify and automate calculations and provide more attention and
time to the basic principles of statistics, mathematization of real-life
situations and following interpretation of results. We now introduce
our own web-site for hypothesis testing. Its didactic aspects, the
technical possibilities of the individual tools, the experience of use
and the advantages or disadvantages are discussed in this paper. This
web-site is not a substitute for common statistical software but should
significantly improve the teaching of statistics at universities.
Abstract: Software Architecture is the basic structure of
software that states the development and advancement of a software
system. Software architecture is also considered as a significant tool
for the construction of high quality software systems. A clean design
leads to the control, value and beauty of software resulting in its
longer life while a bad design is the cause of architectural erosion
where a software evolution completely fails. This paper discusses the
occurrence of software architecture erosion and presents a set of
methods for the detection, declaration and prevention of architecture
erosion. The causes and symptoms of architecture erosion are
observed with the examples of prescriptive and descriptive
architectures and the practices used to stop this erosion are also
discussed by considering different types of software erosion and their
affects. Consequently finding and devising the most suitable
approach for fighting software architecture erosion and in some way
reducing its affect is evaluated and tested on different scenarios.
Abstract: Axial flow fans, while incapable of developing high
pressures, they are well suitable for handling large volumes of air at
relatively low pressures. In general, they are low in cost and possess
good efficiency, and can have blades of airfoil shape. Axial flow fans
show good efficiencies, and can operate at high static pressures if
such operation is necessary. Our objective is to model and analyze
the flow through AXIAL FANS using CFD Software and draw
inference from the obtained results, so as to get maximum efficiency.
The performance of an axial fan was simulated using CFD and the
effect of variation of different parameters such as the blade number,
noise level, velocity, temperature and pressure distribution on the
blade surface was studied. This paper aims to present a final 3D CAD
model of axial flow fan. Adapting this model to the available
components in the market, the first optimization was done. After this
step, CFX flow solver is used to do the necessary numerical analyses
on the aerodynamic performance of this model. This analysis results
in a final optimization of the proposed 3D model which is presented
in this article.
Abstract: Many of the ever-growing elderly population require
exercise, such as running, for health management. One important
element of a runner’s training is the choice of shoes for exercise; shoes
are important because they provide the interface between the feet and
road. When we purchase shoes, we may instinctively choose a pair
after trying on many different pairs of shoes. Selecting the shoes
instinctively may work, but it does not guarantee a suitable fit for
running activities. Therefore, if we could select suitable shoes for each
runner from the viewpoint of brain activities, it would be helpful for
validating shoe selection. In this paper, we describe how brain
activities show different characteristics during particular task,
corresponding to different properties of shoes. Using five subjects, we
performed a verification experiment, applying weight, softness, and
flexibility as shoe properties. In order to affect the shoe property’s
differences to the brain, subjects run for 10 min. Before and after
running, subjects conducted a paced auditory serial addition task
(PASAT) as the particular task; and the subjects’ brain activities
during the PASAT are evaluated based on oxyhemoglobin and
deoxyhemoglobin relative concentration changes, measured by
near-infrared spectroscopy (NIRS). When the brain works actively,
oxihemoglobin and deoxyhemoglobin concentration drastically
changes; therefore, we calculate the maximum values of concentration
changes. In order to normalize relative concentration changes after
running, the maximum value are divided by before running maximum
value as evaluation parameters. The classification of the groups of
shoes is expressed on a self-organizing map (SOM). As a result,
deoxyhemoglobin can make clusters for two of the three types of
shoes.
Abstract: The Smart Help for persons with disability (PWD) is a
part of the project SMARTDISABLE which aims to develop relevant
solution for PWD that target to provide an adequate workplace
environment for them. It would support PWD needs smartly through
smart help to allow them access to relevant information and
communicate with other effectively and flexibly, and smart editor
that assist them in their daily work. It will assist PWD in knowledge
processing and creation as well as being able to be productive at the
work place. The technical work of the project involves design of a
technological scenario for the Ambient Intelligence (AmI) - based
assistive technologies at the workplace consisting of an integrated
universal smart solution that suits many different impairment
conditions and will be designed to empower the Physically disabled
persons (PDP) with the capability to access and effectively utilize the
ICTs in order to execute knowledge rich working tasks with
minimum efforts and with sufficient comfort level. The proposed
technology solution for PWD will support voice recognition along
with normal keyboard and mouse to control the smart help and smart
editor with dynamic auto display interface that satisfies the
requirements for different PWD group. In addition, a smart help will
provide intelligent intervention based on the behavior of PWD to
guide them and warn them about possible misbehavior. PWD can
communicate with others using Voice over IP controlled by voice
recognition. Moreover, Auto Emergency Help Response would be
supported to assist PWD in case of emergency. This proposed
technology solution intended to make PWD very effective at the
work environment and flexible using voice to conduct their tasks at
the work environment. The proposed solution aims to provide
favorable outcomes that assist PWD at the work place, with the
opportunity to participate in PWD assistive technology innovation
market which is still small and rapidly growing as well as upgrading
their quality of life to become similar to the normal people at the
workplace. Finally, the proposed smart help solution is applicable in
all workplace setting, including offices, manufacturing, hospital, etc.
Abstract: Components with sensory properties such as gentelligent components developed at the Collaborative Research Centre 653 offer a new angle in terms of the full utilization of the remaining service life as well as preventive maintenance. The developed methodology of component status driven maintenance analyzes the stress data obtained during the component's useful life and on the basis of this knowledge assesses the type of maintenance required in this case. The procedure is derived from the case-based reasoning method and will be explained in detail. The method's functionality is demonstrated with real-life data obtained during test runs of a racing car prototype.
Abstract: Today’s modern interconnected power system is
highly complex in nature. In this, one of the most important
requirements during the operation of the electric power system is the
reliability and security. Power and frequency oscillation damping
mechanism improve the reliability. Because of power system
stabilizer (PSS) low speed response against of major fault such as
three phase short circuit, FACTs devise that can control the network
condition in very fast time, are becoming popular. But FACTs
capability can be seen in a major fault present when nonlinear models
of FACTs devise and power system equipment are applied. To realize
this aim, the model of multi-machine power system with FACTs
controller is developed in MATLAB/SIMULINK using Sim Power
System (SPS) blockiest. Among the FACTs device, Static
synchronous series compensator (SSSC) due to high speed changes
its reactance characteristic inductive to capacitive, is effective power
flow controller. Tuning process of controller parameter can be
performed using different method. But Genetic Algorithm (GA)
ability tends to use it in controller parameter tuning process. In this
paper firstly POD controller is used to power oscillation damping.
But in this station, frequency oscillation dos not has proper damping
situation. So FOD controller that is tuned using GA is using that
cause to damp out frequency oscillation properly and power
oscillation damping has suitable situation.
Abstract: The extermination and proper disposal of
pharmaceutical wastes from expired and unused medications remains
a disputable issue due to their specific nature and characteristics.
Even though the hazards from these wastes are already well known in
terms of environment and human health, people still treat them as
usual wastes. At a national level, in many countries the management
of pharmaceutical and medical wastes has been one of the main
objectives in order to protect people’s health and the environment.
Even though many legal regulations exist in this respect, there has not
been a single law that would clearly explain the procedures of
returning medicines, ways of selection, treatment and extermination
of pharmaceutical wastes. This paper aims at analyzing the practices
of pharmaceutical waste management and treatment in some
European countries as well as a review of the legislation and official
guidelines in managing these kinds of wastes and protecting the
environment and human health. A suitable treatment and
management of expired medications and other similar wastes would
be in the interest of public health in the first place, as well as in the
interest of healthcare institutions and other bodies engaged in
environment protection.
Abstract: The electric power supplied by a photovoltaic power
generation systems depends on the solar irradiation and temperature.
The PV system can supply the maximum power to the load at a
particular operating point which is generally called as maximum
power point (MPP), at which the entire PV system operates with
maximum efficiency and produces its maximum power. Hence, a
Maximum power point tracking (MPPT) methods are used to
maximize the PV array output power by tracking continuously the
maximum power point. The proposed MPPT controller is designed
for 10kW solar PV system installed at Cape Institute of Technology.
This paper presents the fuzzy logic based MPPT algorithm. However,
instead of one type of membership function, different structures of
fuzzy membership functions are used in the FLC design. The
proposed controller is combined with the system and the results are
obtained for each membership functions in Matlab/Simulink
environment. Simulation results are decided that which membership
function is more suitable for this system.
Abstract: Yttrium oxide (Y2O3) films have been successfully
deposited with yttrium-ethylenediamine tetraacetic acid (EDTA·Y·H)
complexes prepared by various milling techniques. The effects of the
properties of the EDTA·Y·H complex on the properties of the
deposited Y2O3 films have been analyzed. Seven different types of the
raw EDTA·Y·H complexes were prepared by various commercial
milling techniques such as ball milling, hammer milling, commercial
milling, and mortar milling. The milled EDTA·Y·H complexes
exhibited various particle sizes and distributions, depending on the
milling method. Furthermore, we analyzed the crystal structure,
morphology and elemental distribution profile of the metal oxide films
deposited on stainless steel substrate with the milled EDTA·Y·H
complexes. Depending on the milling technique, the flow properties of
the raw powders differed. The X-ray diffraction pattern of all the
samples revealed the formation of Y2O3 crystalline phase, irrespective
of the milling technique. Of all the different milling techniques, the
hammer milling technique is considered suitable for fabricating dense
Y2O3 films.