Abstract: In this paper, reliable consensus of multi-agent systems
with sampled-data is investigated. By using a suitable
Lyapunov-Krasovskii functional and some techniques such as
Wirtinger Inequality, Schur Complement and Kronecker Product, the
results of such system are obtained by solving a set of Linear Matrix
Inequalities (LMIs). One numerical example is included to show the
effectiveness of the proposed criteria.
Abstract: Epidermal Growth Factor (EGF, Mw=6,045) has been
reported to have high efficiency of wound repair and anti-wrinkle
effect. However, the half-life of EGF in the body is too short to exert
the biological activity effectively when applied in free form. Growth
Factors can be stabilized by immobilization with carbohydrates from
thermal and proteolytic degradation. Low molecular weight chitosan
(LMCS) and its derivate prepared by hydrogen peroxide has high
solubility. LM6A6DC was successfully prepared as a reactive
carbohydrate for the stabilization of EGF by the reactions of LMCS
with alkalization, tosylation, azidation and reduction. The structure of
LM6A6DC was confirmed by FT-IR, 1H NMR and elementary
analysis. For enhancing the stability of free EGF, EGF was attached
with LM6A6DC by using water-soluble carbodiimide.
EGF-LM6A6DC conjugates did not show any cytotoxicity on the
Normal Human Dermal Fibroblast (NHDF) 3T3 proliferation at least
under 100 μg/ml. In the result, it was considered that LM6A6DC is
suitable to immobilize of growth factor.
Abstract: The paper deals with behaviour of the segment 50+ in
the financial market in the Czech Republic. This segment could be
said as the strong market power and it can be a crucial business
potential for financial business units. The main defined objective of
this paper is analysis of the customers´ behaviour of the segment 50-
60 years in the financial market in the Czech Republic and proposal
making of the suitable marketing approach to satisfy their demands in
the area of product, price, distribution and marketing communication
policy. This paper is based on data from one part of primary
marketing research. Paper determinates the basic problem areas as
well as definition of financial services marketing, defining the
primary research problem, hypothesis and primary research
methodology. Finally suitable marketing approach to selected sub
segment at age of 50-60 years is proposed according to marketing
research findings.
Abstract: The pursuit of the MPPT has led to the development of many kinds of controllers, one of which is the Fuzzy Logic controller, which has proven its worth. To further tune this controller this paper will discuss and analyze the use of Genetic Algorithms to tune the Fuzzy Logic Controller. It will provide an introduction to both systems, and test their compatibility and performance.
Abstract: The paper presents a practical three-phase PWM
inverter suitable for low voltage, low rating energy efficient systems.
The work in the paper is conducted with the view to establishing the
significance of the loss contribution from the PWM inverter in the
determination of the complete losses of a photovoltaic (PV) arraypowered
induction motor drive water pumping system. Losses
investigated include; conduction and switching loss of the devices
and gate drive losses. It is found that the PWM inverter operates at a
reasonable variable efficiency that does not fall below 92%
depending on the load. The results between the simulated and
experimental results for the system with or without a maximum
power tracker (MPT) compares very well, within an acceptable range
of 2% margin.
Abstract: Maize constitutes a major agrarian production for use
by the vast population but despite its economic importance; it has not
been produced to meet the economic needs of the country. Achieving
optimum yield in maize can meaningfully be supported by land
suitability analysis in order to guarantee self-sufficiency for future
production optimization. This study examines land suitability for
maize production through the analysis of the physicochemical
variations in soil properties and other land attributes over space using
a Geographic Information System (GIS) framework.
Physicochemical parameters of importance selected include slope,
landuse, physical and chemical properties of the soil, and climatic
variables. Landsat imagery was used to categorize the landuse,
Shuttle Radar Topographic Mapping (SRTM) generated the slope and
soil samples were analyzed for its physical and chemical components.
Suitability was categorized into highly, moderately and marginally
suitable based on Food and Agricultural Organisation (FAO)
classification, using the Analytical Hierarchy Process (AHP)
technique of GIS. This result can be used by small scale farmers for
efficient decision making in the allocation of land for maize
production.
Abstract: A Disaster Management System (DMS) is very important for countries with multiple disasters, such as Chile. In the world (also in Chile)different disasters (earthquakes, tsunamis, volcanic eruption, fire or other natural or man-made disasters) happen and have an effect on the population. It is also possible that two or more disasters occur at the same time. This meansthata multi-risk situation must be mastered. To handle such a situation a Decision Support System (DSS) based on multiagents is a suitable architecture. The most known DMSs are concernedwith only a singledisaster (sometimes thecombination of earthquake and tsunami) and often with a particular disaster. Nevertheless, a DSS helps for a better real-time response. Analyze the existing systems in the literature and expand them for multi-risk disasters to construct a well-organized system is the proposal of our work. The here shown work is an approach of a multi-risk system, which needs an architecture and well defined aims. In this moment our study is a kind of case study to analyze the way we have to follow to create our proposed system in the future.
Abstract: Fluid viscous damping systems are well suited for
many air vehicles subjected to shock and vibration. These damping
system work with the principle of viscous fluid throttling through the
orifice to create huge pressure difference between compression and
rebound chamber and obtain the required damping force. One
application of such systems is its use in aircraft door system to
counteract the door’s velocity and safely stop it. In exigency
situations like crash or emergency landing where the door doesn’t
open easily, possibly due to unusually tilting of fuselage or some
obstacles or intrusion of debris obstruction to move the parts of the
door, such system can be combined with other systems to provide
needed force to forcefully open the door and also securely stop it
simultaneously within the required time i.e. less than 8 seconds. In
the present study, a hydraulic system called snubber along with other
systems like actuator, gas bottle assembly which together known as
emergency power assist system (EPAS) is designed, built and
experimentally studied to check the magnitude of angular velocity,
damping force and time required to effectively open the door.
Whenever needed, the gas pressure from the bottle is released to
actuate the actuator and at the same time pull the snubber’s piston to
operate the emergency opening of the door. Such EPAS installed in
the suspension arm of the aircraft door is studied explicitly changing
parameters like orifice size, oil level, oil viscosity and bypass valve
gap and its spring of the snubber at varying temperature to generate
the optimum design case. Comparative analysis of the EPAS at
several cases is done and conclusions are made. It is found that
during emergency condition, the system opening time and angular
velocity, when snubber with 0.3mm piston and shaft orifice and
bypass valve gap of 0.5 mm with its original spring is used, shows
significant improvement over the old ones.
Abstract: Precise capture of plantar 3D surface of the foot at the
loading gait phases on rigid substrates was found to be valuable for
the assessment of the physiology, health and problems of the feet.
Photogrammetry, a precision 3D spatial data capture technique is
suitable for this type of dynamic application. In this research, the
technique is utilised to study the plantar deformation as a result of
having a strip of kinesiology tape on the plantar surface during the
loading phase of gait. For this pilot study, one healthy adult male
subject was recruited under the University’s human research ethics
guidelines for this preliminary study. The 3D plantar deformation
data with and without applying the tape were analysed. The results
and analyses are presented together with detailed findings.
Abstract: The characteristic requirement for producing
rectangular shape bottles was a uniform thickness of the plastic bottle
wall. Die shaping was a good technique which controlled the wall
thickness of bottles. An advance technology which was the finite
element method (FEM) for blowing parison to be a rectangular shape
bottle was conducted to reduce waste plastic from a trial and error
method of a die shaping and parison control method. The artificial
intelligent (AI) comprised of artificial neural network and genetic
algorithm was selected to optimize the die gap shape from the FEM
results. The application of AI technique could optimize the suitable
die gap shape for the parison blow molding which did not depend on
the parison control method to produce rectangular bottles with the
uniform wall. Particularly, this application can be used with cheap
blow molding machines without a parison controller therefore it will
reduce cost of production in the bottle blow molding process.
Abstract: Composite material based on Fe3Si micro-particles
and Mn-Zn nano-ferrite was prepared using powder metallurgy
technology. The sol-gel followed by autocombustion process was
used for synthesis of Mn0.8Zn0.2Fe2O4 ferrite. 3 wt.% of mechanically
milled ferrite was mixed with Fe3Si powder alloy. Mixed micro-nano
powder system was homogenized by the Resonant Acoustic Mixing
using ResodynLabRAM Mixer. This non-invasive homogenization
technique was used to preserve spherical morphology of Fe3Si
powder particles. Uniaxial cold pressing in the closed die at pressure
600 MPa was applied to obtain a compact sample. Microwave
sintering of green compact was realized at 800°C, 20 minutes, in air.
Density of the powders and composite was measured by
Hepycnometry. Impulse excitation method was used to measure
elastic properties of sintered composite. Mechanical properties were
evaluated by measurement of transverse rupture strength (TRS) and
Vickers hardness (HV). Resistivity was measured by 4 point probe
method. Ferrite phase distribution in volume of the composite was
documented by metallographic analysis.
It has been found that nano-ferrite particle distributed among
micro- particles of Fe3Si powder alloy led to high relative density
(~93%) and suitable mechanical properties (TRS >100 MPa, HV
~1GPa, E-modulus ~140 GPa) of the composite. High electric
resistivity (R~6.7 ohm.cm) of prepared composite indicate their
potential application as soft magnetic material at medium and high
frequencies.
Abstract: This paper describes an analysis of Yacht Simulator
international trends and also explains about Yacht. The results are
summarized as follows. Attached to the cockpit are sensors that feed
-back information on rudder angle, boat heel angle and mainsheet
tension to the computer. Energy expenditure of the sailor measure
indirectly using expired gas analysis for the measurement of VO2 and
VCO2. At sea course configurations and wind conditions can be preset
to suit any level of sailor from complete beginner to advanced sailor.
Abstract: PLA emerged as a promising polymer because of its
property as a compostable, biodegradable thermoplastic made from
renewable sources. PLA can be polymerized from monomers
(Lactide or Lactic acid) obtained by fermentation processes from
renewable sources such as corn starch or sugarcane. For PLA
synthesis, ring opening polymerization (ROP) of Lactide monomer is
one of the preferred methods. In the literature, the technique mainly
developed for ROP of PLA is based on metal/bimetallic catalyst (Sn,
Zn and Al) or other organic catalysts in suitable solvent. However,
the PLA synthesized using such catalysts may contain trace elements
of the catalyst which may cause toxicity. This work estimated the
usefulness and drawbacks of using different catalysts as well as effect
of alternative energies and future aspects for PLA production.
Abstract: A knowledge-based expert system with the acronym
RASPE is developed as an application tool to help decision makers in
construction companies make informed decisions about managing
risks in pipeline construction projects. Choosing to use expert
systems from all available artificial intelligence techniques is due to
the fact that an expert system is more suited to representing a
domain’s knowledge and the reasoning behind domain-specific
decisions. The knowledge-based expert system can capture the
knowledge in the form of conditional rules which represent various
project scenarios and potential risk mitigation/response actions. The
built knowledge in RASPE is utilized through the underlying
inference engine that allows the firing of rules relevant to a project
scenario into consideration. Paper provides an overview of the
knowledge acquisition process and goes about describing the
knowledge structure which is divided up into four major modules.
The paper shows one module in full detail for illustration purposes
and concludes with insightful remarks.
Abstract: In this paper, two options of anodic alumina barrier
layer thinning have been demonstrated. The approaches varied with
the duration of the voltage step. It was found that too long step of the
barrier layer thinning process leads to chemical etching of the
nanopores on their top. At the bottoms pores are not fully opened
what is disadvantageous for further applications in nanofabrication.
On the other hand, while the duration of the voltage step is controlled
by the current density (value of the current density cannot exceed
75% of the value recorded during previous voltage step) the pores are
fully opened. However, pores at the bottom obtained with this
procedure have smaller diameter, nevertheless this procedure
provides electric contact between the bare aluminum (substrate) and
electrolyte, what is suitable for template assisted electrodeposition,
one of the most cost-efficient synthesis method in nanotechnology.
Abstract: The aim of this study is to develop an anterior lumbar
interbody fusion (ALIF) PEEK cage suitable for Korean people. In this
study, CT images were obtained from Korean male (173cm, 71kg) and
3D Korean lumbar models were reconstructed based on the CT images
to investigate anatomical characteristics. Major design parameters of
anterior lumbar interbody fusion (ALIF) PEEK Cage were selected
using the morphological measurement information of the Korean
Lumbar models. Through finite element analysis and mechanical tests,
the developed ALIFPEEK Cage prototype was compared with the
Fidji Cage (Zimmer. Inc, USA) and it was found that the ALIF
prototype showed similar and/or superior mechanical performance
compared to the FidJi Cage. Also, clinical validation for the ALIF
PEEK Cage prototype was carried out to check predictable troubles in
surgical operations. Finally, it is considered that the convenience and
stability of the prototype was clinically verified.
Abstract: Numeracy, like Literacy is considered to be a core
value of modern societies. Most higher education institutions in
South Africa include being numerate as an important graduate
attribute. It is argued that a suitability numerate society contributes to
social justice, empowerment, financial and environmental
sustainability and a lack of numeracy practices can contribute to
disempowerment.
Numeracy is commonly misconstrued as a basic and simple
practice, similar in nature to basic arithmetic. This study highlights
the complexities of higher education numeracy practices by analyzing
a programme in a higher education institution in South Africa using
the New Literacies Studies perspective.
Abstract: Vegetation affects the mean and turbulent flow
structure. It may increase flood risks and sediment transport.
Therefore, it is important to develop analytical approaches for the bed
shear stress on vegetated bed, to predict resistance caused by
vegetation. In the recent years, experimental and numerical models
have both been developed to model the effects of submerged
vegetation on open-channel flow. In this paper, different analytic
models are compared and tested using the criteria of deviation, to
explore their capacity for predicting the mean velocity and select the
suitable one that will be applied in real case of rivers. The
comparison between the measured data in vegetated flume and
simulated mean velocities indicated, a good performance, in the case
of rigid vegetation, whereas, Huthoff model shows the best
agreement with a high coefficient of determination (R2=80%) and the
smallest error in the prediction of the average velocities.
Abstract: In Brazil, neonatal mortality rate is considered
incompatible with the country development conditions, and has been
a Public Health concern. Reduction in infant mortality rates has also
been part of the Millennium Development Goals, a commitment
made by countries, members of the Organization of United Nations
(OUN), including Brazil. Fetal mortality rate is considered a highly
sensitive indicator of health care quality. Suitable actions, such as
good quality and access to health services may contribute positively
towards reduction in these fetal and neonatal rates. With appropriate
antenatal follow-up and health care during gestation and delivery,
some death causes could be reduced or even prevented by means of
early diagnosis and intervention, as well as changes in risk factors
and interventions. Objectives: To study the quality of maternal and
infant health care based on fetal and neonatal mortality, as well as the
possible actions to prevent those deaths in Botucatu (Brazil).
Methods: Classification of prevention according to the International
Classification of Diseases and the modified Wigglesworth´s
classification. In order to evaluate adequacy, indicators of quality of
antenatal and delivery care were established by the authors. Results:
Considering fetal deaths, 56.7% of them occurred before delivery,
which reveals possible shortcomings in antenatal care, and 38.2% of
them were a result of intra- labor changes, which could be prevented
or reduced by adequate obstetric management. These findings were
different from those in the group of early neonatal deaths which were
also studied. Adequacy of health services showed that antenatal and
childbirth care was appropriate for 24% and 33.3% of pregnant
women, respectively, which corroborates the results of prevention.
These results revealed that shortcomings in obstetric and antenatal
care could be the causes of deaths in the study. Early and late
neonatal deaths have similar characteristics: 76% could be prevented
or reduced mainly by adequate newborn care (52.9%) and adequate
health care for gestational women (11.7%). When adequacy of care
was evaluated, childbirth and newborn care was adequate in 25.8%
and antenatal care was adequate in 16.1%. In conclusion, direct
relationship was found between adequacy and quality of care
rendered to pregnant women and newborns, and fetal and infant
mortality. Moreover, our findings highlight that deaths could be
prevented by an adequate obstetric and neonatal management.
Abstract: The aim of this work was to apply extractive
distillation for acetonitrile removal from water solutions, to validate
thermodynamic criterion based on excess Gibbs energy to entrainer
selection process for acetonitrile – water mixture separation and show
its potential efficiency at isothermal conditions as well as at isobaric
(conditions of real distillation process), to simulate and analyze an
extractive distillation process with chosen entrainers: optimize
amount of trays and feeds, entrainer/original mixture and reflux
ratios. Equimolar composition of the feed stream was chosen for the
process, comparison of the energy consumptions was carried out.
Glycerol was suggested as the most energetically and ecologically
suitable entrainer.