Abstract: Bottom ash from Municipal Solid Waste Incineration
(MSWI) can be viewed as a typical granular material because these
industrial by-products result from the incineration of various
domestic wastes. MSWI bottom ash is mainly used in road
engineering in substitution of the traditional natural aggregates. As
the characterization of their mechanical behavior is essential in order
to use them, specific studies have been led over the past few years. In
the first part of this paper, the mechanical behavior of MSWI bottom
ash is studied with triaxial tests. After, analysis of the experiment
results, the simulation of triaxial tests is carried out by using the
software package CESAR-LCPC. As the first approach in modeling
of this new class material, the Mohr-Coulomb model was chosen to
describe the evolution of material under the influence of external
mechanical actions.
Abstract: The paper presents a method in which the expert
knowledge is applied to fuzzy inference model. Even a less
experienced person could benefit from the use of such a system, e.g.
urban planners, officials. The analysis result is obtained in a very
short time, so a large number of the proposed locations can also be
verified in a short time. The proposed method is intended for testing
of locations of car parks in a city. The paper shows selected examples
of locations of the P&R facilities in cities planning to introduce the
P&R. The analyses of existing objects are also shown in the paper
and they are confronted with the opinions of the system users, with
particular emphasis on unpopular locations. The results of the
analyses are compared to expert analysis of the P&R facilities
location that was outsourced by the city and the opinions about
existing facilities users that were expressed on social networking
sites. The obtained results are consistent with actual users’ feedback.
The proposed method proves to be good, but does not require the
involvement of a large experts team and large financial contributions
for complicated research. The method also provides an opportunity to
show the alternative location of P&R facilities. Although the results
of the method are approximate, they are not worse than results of
analysis of employed experts. The advantage of this method is ease of
use, which simplifies the professional expert analysis. The ability of
analyzing a large number of alternative locations gives a broader
view on the problem. It is valuable that the arduous analysis of the
team of people can be replaced by the model's calculation. According
to the authors, the proposed method is also suitable for
implementation on a GIS platform.
Abstract: Searching the “Island of stability” is a topic of
extreme interest in theoretical as well as experimental modern
physics today. This “island of stability” is spanned by superheavy
elements (SHE's) that are produced in the laboratory. SHE's are
believed to exist primarily due to the “magic” stabilizing effects of
nuclear shell structure. SHE synthesis is extremely difficult due to
their very low production cross section, often of the order of pico
barns or less. Stabilizing effects of shell closures at proton number
Z=82 and neutron number N=126 are predicted theoretically. Though
stabilizing effects of Z=82 have been experimentally verified, no
concluding observations have been made with N=126, so far. We
measured and analyzed the total evaporation residue (ER) cross
sections for a number of systems with neutron number around 126 to
explore possible shell closure effects in ER cross sections, in this
work.
Abstract: Maintenance and design engineers have great concern
for the functioning of rotating machineries due to the vibration
phenomenon. Improper functioning in rotating machinery originates
from the damage to rolling element bearings. The status of rolling
element bearings require advanced technologies to monitor their
health status efficiently and effectively. Avoiding vibration during
machine running conditions is a complicated process. Vibration
simulation should be carried out using suitable sensors/ transducers to
recognize the level of damage on bearing during machine operating
conditions. Various issues arising in rotating systems are interlinked
with bearing faults. This paper presents an approach for fault
diagnosis of bearings using neural networks and time/frequencydomain
vibration analysis.
Abstract: Currently, there are few user friendly Weigh-in-
Motion (WIM) data analysis softwares available which can produce
traffic input data for the recently developed AASHTOWare pavement
Mechanistic-Empirical (ME) design software. However, these
softwares have only rudimentary Quality Control (QC) processes.
Therefore, they cannot properly deal with erroneous WIM data. As
the pavement performance is highly sensible to the quality of WIM
data, it is highly recommended to use more refined QC process on
raw WIM data to get a good result. This study develops a userfriendly
software, which can produce traffic input for the ME design
software. This software takes the raw data (Class and Weight data)
collected from the WIM station and processes it with a sophisticated
QC procedure. Traffic data such as traffic volume, traffic distribution,
axle load spectra, etc. can be obtained from this software; which can
directly be used in the ME design software.
Abstract: In India, most of the pavement is laid by bituminous
road and the consumption of binder is high for pavement construction
and also modified binders are used to satisfy any specific pavement
requirement. Since the binders are visco-elastic material which is
having the mechanical properties of binder transition from viscoelastic
solid to visco-elastic fluid. In this paper, two different
protocols were used to measure the viscosity property of binder using
a Brookfield Viscometer and there is a need to find the appropriate
mixing and compaction temperatures of various types of binders
which can result in complete aggregate coating and adequate field
density of HMA mixtures. The aim of this work is to find the
transition temperature from Non-Newtonian behavior to Newtonian
behavior of the binder by adopting a steady shear protocol and the
shear rate ramp protocol. The transition from non-Newtonian to
Newtonian can occur through an increase of temperature and shear of
the material. The test has been conducted for unmodified binder VG
30. The transition temperature was found in the unmodified binder
VG is 120oC. Therefore, the application of both modified binder and
unmodified binder in the pavement construction needs to be studied
properly by considering temperature and traffic loading factors of the
respective project site.
Abstract: Cochlear Implantation (CI) which became a routine
procedure for the last decades is an electronic device that provides a
sense of sound for patients who are severely and profoundly deaf.
The optimal success of this implantation depends on the electrode
technology and deep insertion techniques. However, this manual
insertion procedure may cause mechanical trauma which can lead to
severe destruction of the delicate intracochlear structure.
Accordingly, future improvement of the cochlear electrode implant
insertion needs reduction of the excessive force application during
the cochlear implantation which causes tissue damage and trauma.
This study is examined tool-tissue interaction of large prototype scale
digit embedded with distributive tactile sensor based upon cochlear
electrode and large prototype scale cochlea phantom for simulating
the human cochlear which could lead to small scale digit
requirements. The digit, distributive tactile sensors embedded with
silicon-substrate was inserted into the cochlea phantom to measure
any digit/phantom interaction and position of the digit in order to
minimize tissue and trauma damage during the electrode cochlear
insertion. The digit have provided tactile information from the digitphantom
insertion interaction such as contact status, tip penetration,
obstacles, relative shape and location, contact orientation and
multiple contacts. The tests demonstrated that even devices of such a
relative simple design with low cost have potential to improve
cochlear implant surgery and other lumen mapping applications by
providing tactile sensory feedback information and thus controlling
the insertion through sensing and control of the tip of the implant
during the insertion. In that approach, the surgeon could minimize the
tissue damage and potential damage to the delicate structures within
the cochlear caused by current manual electrode insertion of the
cochlear implantation. This approach also can be applied to other
minimally invasive surgery applications as well as diagnosis and path
navigation procedures.
Abstract: The statistical study has become indispensable for various fields of knowledge. Not any different, in Geotechnics the study of probabilistic and statistical methods has gained power considering its use in characterizing the uncertainties inherent in soil properties. One of the situations where engineers are constantly faced is the definition of a probability distribution that represents significantly the sampled data. To be able to discard bad distributions, goodness-of-fit tests are necessary. In this paper, three non-parametric goodness-of-fit tests are applied to a data set computationally generated to test the goodness-of-fit of them to a series of known distributions. It is shown that the use of normal distribution does not always provide satisfactory results regarding physical and behavioral representation of the modeled parameters.
Abstract: The purpose of this study is analyzing the relationship
between trust and social capital of people with using Social Network
Analysis. In this study, two aspects of social capital will be focused:
Bonding, homophilous social capital (BoSC), and Bridging,
heterophilous social capital (BrSC). These two aspects diverge each
other regarding to the social theories. The other concept of the study
is Trust (Tr), namely interpersonal trust, willing to ascribe good
intentions to and have confidence in the words and actions of other
people. In this study, the sample group, 61 people, was selected from
a private firm from the defense industry. The relation between
BoSC/BrSC and Tr is shown by using Social Network Analysis
(SNA) and statistical analysis with Likert type-questionnaire. The
results of the analysis show the Cronbach’s alpha value is 0.756 and
social capital values (BoSC/BrSC) is not correlated with Tr values of
the people.
Abstract: Result from the constant dwindle in natural resources,
the alternative way to reduce the costs in our daily life would be urgent
to be found in the near future. As the ancient technique based on the
theory of solar chimney since roman times, the double-skin façade are
simply composed of two large glass panels in purpose of daylighting
and also natural ventilation in the daytime. Double-skin façade is
generally installed on the exterior side of buildings as function as the
window, so there is always a huge amount of passive solar energy the
façade would receive to induce the airflow every sunny day. Therefore,
this article imposes a domestic double-skin window for residential
usage and attempts to improve the volume flow rate inside the cavity
between the panels by the frame geometry design, the installation of
outlet guide plate and the solar energy collection system. Note that the
numerical analyses are applied to investigate the characteristics of flow
field, and the boundary conditions in the simulation are totally based
on the practical experiment of the original prototype. Then we
redesign the prototype from the knowledge of the numerical results
and fluid dynamic theory, and later the experiments of modified
prototype will be conducted to verify the simulation results. The
velocities at the inlet of each case are increase by 5%, 45% and 15%
from the experimental data, and also the numerical simulation results
reported 20% improvement in volume flow rate both for the frame
geometry design and installation of outlet guide plate.
Abstract: The occurrences of precipitation, also commonly
referred as rain, in the form of "convective" and "stratiform" have
been identified to exist worldwide. In this study, the radar return
echoes or known as reflectivity values acquired from radar scans
have been exploited in the process of classifying the type of rain
endured. The investigation use radar data from Malaysian
Meteorology Department (MMD). It is possible to discriminate the
types of rain experienced in tropical region by observing the vertical
characteristics of the rain structure. .Heavy rain in tropical region
profoundly affects radiowave signals, causing transmission
interference and signal fading. Required wireless system fade margin
depends on the type of rain. Information relating to the two
mentioned types of rain is critical for the system engineers and
researchers in their endeavour to improve the reliability of
communication links. This paper highlights the quantification of
percentage occurrences over one year period in 2009.
Abstract: Environmental concerns about the scarcity of marine
resources are critical driving forces for firms aiming to prepare their
supply chains for sustainability. Building on previous work, this
paper highlights the implementation of good practices geared towards
sustainable operations in the seafood department, which were
pursued in an exploratory retailer case. Outcomes of the adopted
environmentally and socially acceptable fish retailing strategies,
ranged from traceability, to self-certification and eco-labelling. The
consequences for business were, as follows: stronger collaboration
and trust across the chain of custody, improvement of sponsors’
image and of consumers’ loyalty and, progress in the Greenpeace
retailers’ evaluation ranking.
Abstract: In this study, Brillouin Gain Spectrum (BGS) is
experimentally analyzed in the Brillouin Optical Time Domain
Reflectometry (BOTDR) and Brillouin Optical Time Domain
Analyzer (BOTDA). For this purpose, the signal level of the
microwave generator is varied and the effects of BGS are
investigated. In the setups, 20 km conventional single mode fiber is
used to both setups and laser wavelengths are selected around 1550
nm. To achieve best results, it can be used between 5 dBm to 15 dBm
signal level of microwave generator for BOTDA and BOTDR setups.
Abstract: Computer education is referred to as the knowledge
and ability to use computers and related technology efficiently, with a
range of skills covering levels from basic use to advance. Computer
continues to make an ever-increasing impact on all aspect of human
endeavours such as education. With numerous benefits of computer
education, what are the insights of students on computer education?
This study investigated the perception of senior secondary school
students on computer education in Federal Capital Territory (FCT),
Abuja, Nigeria. A sample of 7500 senior secondary schools students
was involved in the study, one hundred (100) private and fifty (50)
public schools within FCT. They were selected by using simple
random sampling technique. A questionnaire [PSSSCEQ] was
developed and validated through expert judgement and reliability coefficient
of 0.84 was obtained. It was used to gather relevant data on
computer education. Findings confirmed that the students in the FCT
had positive perception on computer education. Some factors were
identified that affect students’ perception on computer education. The
null hypotheses were tested using t-test and ANOVA statistical
analyses at 0.05 level of significance. Based on these findings, some
recommendations were made which include competent teachers
should be employed into all secondary schools. This will help
students to acquire relevant knowledge in computer education,
technological supports should be provided to all secondary schools;
this will help the users (students) to solve specific problems in
computer education and financial supports should be provided to
procure computer facilities that will enhance the teaching and the
learning of computer education.
Abstract: In this paper, a linear mixed model which has two
random effects is broken up into two models. This thesis gets
the parameter estimation of the original model and an estimation’s
statistical qualities based on these two models. Then many important
properties are given by comparing this estimation with other general
estimations. At the same time, this paper proves the analysis of
variance estimate (ANOVAE) about σ2 of the original model is equal
to the least-squares estimation (LSE) about σ2 of these two models.
Finally, it also proves that this estimation is better than ANOVAE
under Stein function and special condition in some degree.
Abstract: Lightweight and efficient structures have the aim to
enhance the efficiency of the components in various industries.
Toward this end, composites are one of the most widely used
materials because of durability, high strength and modulus, and low
weight. One type of the advanced composites is grid-stiffened
composite (GSC) structures, which have been extensively considered
in aerospace, automotive, and aircraft industries. They are one of the
top candidates for replacing some of the traditional components,
which are used here. Although there are a good number of published
surveys on the design aspects and fabrication of GSC structures, little
systematic work has been reported on their material modification to
improve their properties, to our knowledge. Matrix modification
using nanoparticles is an effective method to enhance the flexural
properties of the fibrous composites. In the present study, a silanecoupling
agent (3-glycidoxypropyltrimethoxysilane/3-GPTS) was
introduced onto the silica (SiO2) nanoparticle surface and its effects
on the three-point flexural response of isogrid E-glass/epoxy
composites were assessed. Based on the Fourier Transform Infrared
Spectrometer (FTIR) spectra, it was inferred that the 3-GPTS
coupling agent was successfully grafted onto the surface of SiO2
nanoparticles after modification. Flexural test revealed an
improvement of 16%, 14%, and 36% in stiffness, maximum load and
energy absorption of the isogrid specimen filled with 3 wt.% 3-
GPTS/SiO2 compared to the neat one. It would be worth mentioning
that in these structures, considerable energy absorption was observed
after the primary failure related to the load peak. In addition, 3-
GPTMS functionalization had a positive effect on the flexural
behavior of the multiscale isogrid composites. In conclusion, this
study suggests that the addition of modified silica nanoparticles is a
promising method to improve the flexural properties of the gridstiffened
fibrous composite structures.
Abstract: Background modeling and subtraction in video
analysis has been widely used as an effective method for moving
objects detection in many computer vision applications. Recently, a
large number of approaches have been developed to tackle different
types of challenges in this field. However, the dynamic background
and illumination variations are the most frequently occurred problems
in the practical situation. This paper presents a favorable two-layer
model based on codebook algorithm incorporated with local binary
pattern (LBP) texture measure, targeted for handling dynamic
background and illumination variation problems. More specifically,
the first layer is designed by block-based codebook combining with
LBP histogram and mean value of each RGB color channel. Because
of the invariance of the LBP features with respect to monotonic
gray-scale changes, this layer can produce block wise detection results
with considerable tolerance of illumination variations. The pixel-based
codebook is employed to reinforce the precision from the output of the
first layer which is to eliminate false positives further. As a result, the
proposed approach can greatly promote the accuracy under the
circumstances of dynamic background and illumination changes.
Experimental results on several popular background subtraction
datasets demonstrate very competitive performance compared to
previous models.
Abstract: Polymeric composites are being increasingly used as
repair material for repairing critical infrastructures such as building,
bridge, pressure vessel, piping and pipeline. Technique in repairing
damaged pipes is one of the major concerns of pipeline owners.
Considerable researches have been carried out on the repair of
corroded pipes using composite materials. This article attempts a
short review of the subject matter to provide insight into various
techniques used in repairing corroded pipes, focusing on a wide range
of composite repair systems. These systems including pre-cured
layered, flexible wet lay-up, pre-impregnated, split composite sleeve
and flexible tape systems. Both advantages and limitations of these
repair systems were highlighted. Critical technical aspects have been
discussed through the current standards and practices. Research gaps
and future study scopes in achieving more effective design
philosophy are also presented.
Abstract: This experimental study consists of a characterization
of epoxy grout where an amount of 2% of graphene nanoplatelets
particles were added to commercial epoxy resin to evaluate their
behavior regarding neat epoxy resin. Compressive tests, tensile tests
and flexural tests were conducted to study the effect of graphene
nanoplatelets on neat epoxy resin. By comparing graphene-based and
neat epoxy grout, there is no significant increase of strength due to
weak interface in the graphene nanoplatelets/epoxy composites.
From this experiment, the tension and flexural strength of graphenebased
epoxy grouts is slightly lower than ones of neat epoxy grout.
Nevertheless, the addition of graphene has produced more consistent
results according to a smaller standard deviation of strength.
Furthermore, the graphene has also improved the ductility of the
grout, hence reducing its brittle behaviour. This shows that the
performance of graphene-based grout is reliably predictable and able
to minimise sudden rupture. This is important since repair design of
damaged pipeline is of deterministic nature.
Abstract: The major environmental risk of soil pollution is the
contamination of groundwater by infiltration of organic and inorganic
pollutants which can cause a serious menace. To prevent this risk and
to protect the groundwater, we proceeded in this study to test the
reliability of a biosolid as barrier to prevent the migration of very
dangerous pollutants as ‘Cadmium’ through the different soil layers. In this study, we tried to highlight the effect of several parameters
such as: turbidity (different cycle of Hydration/Dehydration),
rainfall, effect of initial Cd(II) concentration and the type of soil.
These parameters allow us to find the most effective manner to
integrate this barrier in the soil. From the results obtained, we found a
significant effect of the barrier. Indeed, the recorded passing
quantities are lowest for the highest rainfall; we noted also that the
barrier has a better affinity towards higher concentrations; the most
retained amounts of cadmium has been in the top layer of the two
types of soil tested, while the lowest amounts of cadmium are
recorded in the bottom layers of soils.