Abstract: An analysis is carried out to investigate the effect of
magnetic field and heat source on the steady boundary layer flow and
heat transfer of a Casson nanofluid over a vertical cylinder stretching
exponentially along its radial direction. Using a similarity
transformation, the governing mathematical equations, with the
boundary conditions are reduced to a system of coupled, non –linear
ordinary differential equations. The resulting system is solved
numerically by the fourth order Runge – Kutta scheme with shooting
technique. The influence of various physical parameters such as
Reynolds number, Prandtl number, magnetic field, Brownian motion
parameter, thermophoresis parameter, Lewis number and the natural
convection parameter are presented graphically and discussed for non
– dimensional velocity, temperature and nanoparticle volume
fraction. Numerical data for the skin – friction coefficient, local
Nusselt number and the local Sherwood number have been tabulated
for various parametric conditions. It is found that the local Nusselt
number is a decreasing function of Brownian motion parameter Nb
and the thermophoresis parameter Nt.
Abstract: The progress of industry integrated circuits in recent
years has been pushed by continuous miniaturization of transistors.
With the reduction of dimensions of components at 0.1 micron and
below, new physical effects come into play as the standard simulators
of two dimensions (2D) do not consider. In fact the third dimension
comes into play because the transverse and longitudinal dimensions
of the components are of the same order of magnitude. To describe
the operation of such components with greater fidelity, we must
refine simulation tools and adapted to take into account these
phenomena. After an analytical study of the static characteristics of
the component, according to the different operating modes, a
numerical simulation is performed of field-effect transistor with
submicron gate MESFET GaInP. The influence of the dimensions of
the gate length is studied. The results are used to determine the
optimal geometric and physical parameters of the component for their
specific applications and uses.
Abstract: The California Bearing Ratio (CBR) has been
acknowledged as an important parameter to characterize the bearing
capacity of earth structures, such as earth dams, road embankments,
airport runways, bridge abutments and pavements. Technically, the
CBR test can be carried out in the laboratory or in the field. The CBR
test is time-consuming and is infrequently performed due to the
equipment needed and the fact that the field moisture content keeps
changing over time. Over the years, many correlations have been
developed for the prediction of CBR by various researchers,
including the dynamic cone penetrometer, undrained shear strength
and Clegg impact hammer. This paper reports and discusses some of
the results from a study on the prediction of CBR. In the current
study, the CBR test was performed in the laboratory on some finegrained
subgrade soils collected from various locations in Victoria.
Based on the test results, a satisfactory empirical correlation was
found between the CBR and the physical properties of the
experimental soils.
Abstract: This study is used as a definition method to the value
and function in manufacturing sector. In concurrence of discussion
about present condition of modeling method, until now definition of
1D-CAE is ambiguity and not conceptual. Across all the physic fields,
those methods are defined with the formulation of differential
algebraic equation which only applied time derivation and simulation.
At the same time, we propose semi-acausal modeling concept and
differential algebraic equation method as a newly modeling method
which the efficiency has been verified through the comparison of
numerical analysis result between the semi-acausal modeling
calculation and FEM theory calculation.
Abstract: Digital image correlation (DIC) is a contactless fullfield
displacement and strain reconstruction technique commonly
used in the field of experimental mechanics. Comparing with
physical measuring devices, such as strain gauges, which only
provide very restricted coverage and are expensive to deploy widely,
the DIC technique provides the result with full-field coverage and
relative high accuracy using an inexpensive and simple experimental
setup. It is very important to study the natural patterns effect on the
DIC technique because the preparation of the artificial patterns is
time consuming and hectic process. The objective of this research is
to study the effect of using images having natural pattern on the
performance of DIC. A systematical simulation method is used to
build simulated deformed images used in DIC. A parameter (subset
size) used in DIC can have an effect on the processing and accuracy
of DIC and even cause DIC to failure. Regarding to the picture
parameters (correlation coefficient), the higher similarity of two
subset can lead the DIC process to fail and make the result more
inaccurate. The pictures with good and bad quality for DIC methods
have been presented and more importantly, it is a systematic way to
evaluate the quality of the picture with natural patterns before they
install the measurement devices.
Abstract: Some regularities of formation of a new structural
state of the thermoplastic polymers - gradually oriented (stretched)
state (GOS) are discussed. Transition into GOS is realized by the
graded oriented stretching - by action of inhomogeneous mechanical
field on the isotropic linear polymers or by zone stretching that is
implemented on a standard tensile-testing machine with using a
specially designed zone stretching device (ZSD). Both technical
approaches (especially zone stretching method) allows to manage the
such quantitative parameters of gradually oriented polymers as a
range of change in relative elongation/orientation degree, length of
this change and profile (linear, hyperbolic, parabolic, logarithmic,
etc.). The possibility of obtaining functionally graded materials
(FGMs) by graded orientation method is briefly discussed. Uniaxial
graded stretching method should be considered as an effective
technological solution to create polymer materials with a
predetermined gradient of physical properties.
Abstract: This paper presents a novel statistical description of
the counterpoise effective length due to lightning surges, where the
(impulse) effective length had been obtained by means of regressive
formulas applied to the transient simulation results. The effective
length is described in terms of a statistical distribution function, from
which median, mean, variance, and other parameters of interest could
be readily obtained. The influence of lightning current amplitude,
lightning front duration, and soil resistivity on the effective length has
been accounted for, assuming statistical nature of these parameters. A
method for determining the optimal counterpoise length, in terms of
the statistical impulse effective length, is also presented. It is based on
estimating the number of dangerous events associated with lightning
strikes. Proposed statistical description and the associated method
provide valuable information which could aid the design engineer in
optimising physical lengths of counterpoises in different grounding
arrangements and soil resistivity situations.
Abstract: Negative pressure phenomenon appears in many
thermodynamic, geophysical and biophysical processes in the Nature
and technological systems. For more than 100 years of the laboratory
researches beginning from F. M. Donny’s tests, the great values of
negative pressure have been achieved. But this phenomenon has not
been practically applied, being only a nice lab toy due to the special
demands for the purity and homogeneity of the liquids for its
appearance. The possibility of creation of direct wave of negative
pressure in real heterogeneous liquid systems was confirmed
experimentally under the certain kinetic and hydraulic conditions.
The negative pressure can be considered as the factor of both useful
and destroying energies. The new approach to generation of the
negative pressure waves in impure, unclean fluids has allowed the
creation of principally new energy saving technologies and
installations to increase the effectiveness and efficiency of different
production processes. It was proved that the negative pressure is one
of the main factors causing hard troubles in some technological and
natural processes. Received results emphasize the necessity to take
into account the role of the negative pressure as an energy factor in
evaluation of many transient thermohydrodynamic processes in the
Nature and production systems.
Abstract: The effect of the inclusion of thyme and rosemary
essential oils into chitosan films, as well as the microbiological and
physical properties when storing chitosan film with and without the
mentioned inclusion was studied. The film forming solution was
prepared by dissolving chitosan (2%, w/v), polysorbate 80 (4% w/w
CH) and glycerol (16% w/w CH) in aqueous lactic acid solutions
(control). The thyme (TEO) and rosemary (REO) essential oils (EOs)
were included 1:1 w/w (EOs:CH) on their combination 50/50
(TEO:REO). The films were stored at temperatures of 5, 20, 33°C
and a relative humidity of 75% during four weeks. The films with
essential oil inclusion did not show an antimicrobial activity against
strains. This behavior could be explained because the chitosan only
inhibits the growth of microorganisms in direct contact with the
active sites. However, the inhibition capacity of TEO was higher than
the REO and a synergic effect between TEO:REO was found for S.
enteritidis strains in the chitosan solution.
Some physical properties were modified by the inclusion of
essential oils. The addition of essential oils does not affect the
mechanical properties (tensile strength, elongation at break, puncture
deformation), the water solubility, the swelling index nor the DSC
behavior. However, the essential oil inclusion can significantly
decrease the thickness, the moisture content, and the L* value of
films whereas the b* value increased due to molecular interactions
between the polymeric matrix, the loosing of the structure, and the
chemical modifications. On the other hand, the temperature and time
of storage changed some physical properties on the chitosan films.
This could have occurred because of chemical changes, such as
swelling in the presence of high humidity air and the reacetylation of
amino groups. In the majority of cases, properties such as moisture
content, tensile strength, elongation at break, puncture deformation,
a*, b*, chrome, 7E increased whereas water resistance, swelling
index, L*, and hue angle decreased.
Abstract: In situ modified cyclohexanone-formaldehyde resins
were prepared by addition of alendronic acid during resin
preparation. Clay nanocomposites in ketonic resins were achieved by
adding clay into the flask at the beginning of the resin preparation.
The prepared resins were used for the synthesis of fire resistant
polyurethanes foam. Both phosphorous containing modifier
compound alendronic acid and nanoclay increases fire resistance of
the cyclohexanone-formaldehyde resin thus polyurethane produced
from these resins. The effect of the concentrations of alendronic acid
and clay on the fire resistance and physical properties of
polyurethanes was studied.
Abstract: Food as perishable goods represents a specific and
sensitive part in the supply chain theory, since changing physical or
chemical characteristics considerably influence the approach to stock
management. The most delicate phase of this process is
transportation, where it becomes difficult to ensure the stable
conditions which limit deterioration, since the value of the
deterioration rate could be easily influenced by the mode of
transportation. The fuzzy definition of variables allows one to take
these variations into account. Furthermore, an appropriate choice of
the defuzzification method permits one to adapt results to real
conditions as far as possible. In this article those methods which take
into account the relationship between the deterioration rate of
perishable goods and transportation by ship will be applied with the
aim of (a) minimizing the total cost function, defined as the sum of
the ordering cost, holding cost, disposing cost and transportation
costs, and (b) improving the supply chain sustainability by reducing
environmental impact and waste disposal costs.
Abstract: Environmental impacts of six 3D printers using
various materials were compared to determine if material choice
drove sustainability, or if other factors such as machine type, machine
size, or machine utilization dominate. Cradle-to-grave life-cycle
assessments were performed, comparing a commercial-scale FDM
machine printing in ABS plastic, a desktop FDM machine printing in
ABS, a desktop FDM machine printing in PET and PLA plastics, a
polyjet machine printing in its proprietary polymer, an SLA machine
printing in its polymer, and an inkjet machine hacked to print in salt
and dextrose. All scenarios were scored using ReCiPe Endpoint H
methodology to combine multiple impact categories, comparing
environmental impacts per part made for several scenarios per
machine. Results showed that most printers’ ecological impacts were
dominated by electricity use, not materials, and the changes in
electricity use due to different plastics was not significant compared
to variation from one machine to another. Variation in machine idle
time determined impacts per part most strongly. However, material
impacts were quite important for the inkjet printer hacked to print in
salt: In its optimal scenario, it had up to 1/38th the impacts coreper
part as the worst-performing machine in the same scenario. If salt
parts were infused with epoxy to make them more physically robust,
then much of this advantage disappeared, and material impacts
actually dominated or equaled electricity use. Future studies should
also measure DMLS and SLS processes / materials.
Abstract: We have developed a new computer program in
Fortran 90, in order to obtain numerical solutions of a system
of Relativistic Magnetohydrodynamics partial differential equations
with predetermined gravitation (GRMHD), capable of simulating
the formation of relativistic jets from the accretion disk of matter
up to his ejection. Initially we carried out a study on numerical
methods of unidimensional Finite Volume, namely Lax-Friedrichs,
Lax-Wendroff, Nessyahu-Tadmor method and Godunov methods
dependent on Riemann problems, applied to equations Euler in
order to verify their main features and make comparisons among
those methods. It was then implemented the method of Finite
Volume Centered of Nessyahu-Tadmor, a numerical schemes that
has a formulation free and without dimensional separation of
Riemann problem solvers, even in two or more spatial dimensions,
at this point, already applied in equations GRMHD. Finally, the
Nessyahu-Tadmor method was possible to obtain stable numerical
solutions - without spurious oscillations or excessive dissipation -
from the magnetized accretion disk process in rotation with respect
to a central black hole (BH) Schwarzschild and immersed in a
magnetosphere, for the ejection of matter in the form of jet over a
distance of fourteen times the radius of the BH, a record in terms
of astrophysical simulation of this kind. Also in our simulations,
we managed to get substructures jets. A great advantage obtained
was that, with the our code, we got simulate GRMHD equations in
a simple personal computer.
Abstract: The thermal conductivity of a fluid can be
significantly enhanced by dispersing nano-sized particles in it, and
the resultant fluid is termed as "nanofluid". A theoretical model for
estimating the thermal conductivity of a nanofluid has been proposed
here. It is based on the mechanism that evenly dispersed
nanoparticles within a nanofluid undergo Brownian motion in course
of which the nanoparticles repeatedly collide with the heat source.
During each collision a rapid heat transfer occurs owing to the solidsolid
contact. Molecular dynamics (MD) simulation of the collision
of nanoparticles with the heat source has shown that there is a pulselike
pick up of heat by the nanoparticles within 20-100 ps, the extent
of which depends not only on thermal conductivity of the
nanoparticles, but also on the elastic and other physical properties of
the nanoparticle. After the collision the nanoparticles undergo
Brownian motion in the base fluid and release the excess heat to the
surrounding base fluid within 2-10 ms. The Brownian motion and
associated temperature variation of the nanoparticles have been
modeled by stochastic analysis. Repeated occurrence of these events
by the suspended nanoparticles significantly contributes to the
characteristic thermal conductivity of the nanofluids, which has been
estimated by the present model for a ethylene glycol based nanofluid
containing Cu-nanoparticles of size ranging from 8 to 20 nm, with
Gaussian size distribution. The prediction of the present model has
shown a reasonable agreement with the experimental data available
in literature.
Abstract: Liposome plays an important role in medical and
pharmaceutical science as e.g. nano scale drug carriers. Liposomes
are vesicles of varying size consisting of a spherical lipid bilayer and
an aqueous inner compartment. Magnet-driven liposome used for the
targeted delivery of drugs to organs and tissues. These liposome
preparations contain encapsulated drug components and finely
dispersed magnetic particles.
Liposomes are vesicles of varying size consisting of a spherical
lipid bilayer and an aqueous inner compartment that are generated in
vitro. These are useful in terms of biocompatibility, biodegradability,
and low toxicity, and can control biodistribution by changing the size,
lipid composition, and physical characteristics. Furthermore,
liposomes can entrap both hydrophobic and hydrophilic drugs and are
able to continuously release the entrapped substrate, thus being useful
drug carriers. Magnetic liposomes (MLs) are phospholipid vesicles
that encapsulate magneticor paramagnetic nanoparticles. They are
applied as contrast agents for magnetic resonance imaging (MRI).
The biological synthesis of nanoparticles using plant extracts plays
an important role in the field of nanotechnology. Green-synthesized
magnetite nanoparticles-protein hybrid has been produced by treating
Iron (III) / Iron (II) chloride with the leaf extract of Datura inoxia.
The phytochemicals present in the leaf extracts act as a reducing as
well stabilizing agents preventing agglomeration, which include
flavonoids, phenolic compounds, cardiac glycosides, proteins and
sugars.
The magnetite nanoparticles-protein hybrid has been trapped
inside the aqueous core of the liposome prepared by reversed phase
evaporation (REV) method using oleic and linoleic acid which has
been shown to be driven under magnetic field confirming the
formation magnetic liposome (ML). Chemical characterization of
stealth magnetic liposome has been performed by breaking the
liposome and release of magnetic nanoparticles. The presence iron
has been confirmed by colour complex formation with KSCN and
UV-Vis study using spectrophotometer Cary 60, Agilent.
This magnet driven liposome using nanoparticles-protein hybrid
can be a smart vesicles for the targeted drug delivery.
Abstract: In recent years, the compression of date (Phoenix
dactylifera L.) fruit powders (DP) to obtain date tablets (DT) has
been suggested as a promising form of valorization of non
commercial valuable date fruit (DF) varieties. To further improve
and characterize DT, the present study aims to investigate the
influence of the DP particle size and compression force on some
physical properties of DT. The results show that independently of
particle size, the hardness (y) of tablets increases with the increase of
the compression force (x) following a logarithmic law (y = a ln (bx)
where a and b are the constants of model). Further, a full factorial
design (FFD) at two levels, applied to investigate the erosion %,
reveals that the effects of time and particle size are the same in
absolute value and they are beyond the effect of the compression.
Regarding the disintegration time, the obtained results also by means
of a FFD show that the effect of the compression force exceeds 4
times that of the DP particle size. As final stage, the color parameters
in the CIELab system of DT immediately after their obtaining are
differently influenced by the size of the initial powder.
Abstract: The final step to complete the “Analytical Systems
Engineering Process” is the “Allocated Architecture” in which all
Functional Requirements (FRs) of an engineering system must be
allocated into their corresponding Physical Components (PCs). At
this step, any design for developing the system’s allocated
architecture in which no clear pattern of assigning the exclusive
“responsibility” of each PC for fulfilling the allocated FR(s) can be
found is considered a poor design that may cause difficulties in
determining the specific PC(s) which has (have) failed to satisfy a
given FR successfully. The present study utilizes the Axiomatic
Design method principles to mathematically address this problem and
establishes an “Axiomatic Model” as a solution for reaching good
alternatives for developing the allocated architecture. This study
proposes a “loss Function”, as a quantitative criterion to monetarily
compare non-ideal designs for developing the allocated architecture
and choose the one which imposes relatively lower cost to the
system’s stakeholders. For the case-study, we use the existing design
of U. S. electricity marketing subsystem, based on data provided by
the U.S. Energy Information Administration (EIA). The result for
2012 shows the symptoms of a poor design and ineffectiveness due to
coupling among the FRs of this subsystem.
Abstract: Safety is one of the most important considerations
when buying a new car. While active safety aims at avoiding
accidents, passive safety systems such as airbags and seat belts
protect the occupant in case of an accident. In addition to legal
regulations, organizations like Euro NCAP provide consumers with
an independent assessment of the safety performance of cars and
drive the development of safety systems in automobile industry.
Those ratings are mainly based on injury assessment reference values
derived from physical parameters measured in dummies during a car
crash test.
The components and sub-systems of a safety system are designed
to achieve the required restraint performance. Sled tests and other
types of tests are then carried out by car makers and their suppliers
to confirm the protection level of the safety system. A Knowledge
Discovery in Databases (KDD) process is proposed in order to
minimize the number of tests. The KDD process is based on the
data emerging from sled tests according to Euro NCAP specifications.
About 30 parameters of the passive safety systems from different data
sources (crash data, dummy protocol) are first analysed together with
experts opinions. A procedure is proposed to manage missing data
and validated on real data sets. Finally, a procedure is developed to
estimate a set of rough initial parameters of the passive system before
testing aiming at reducing the number of tests.
Abstract: The Smart Help for persons with disability (PWD) is a
part of the project SMARTDISABLE which aims to develop relevant
solution for PWD that target to provide an adequate workplace
environment for them. It would support PWD needs smartly through
smart help to allow them access to relevant information and
communicate with other effectively and flexibly, and smart editor
that assist them in their daily work. It will assist PWD in knowledge
processing and creation as well as being able to be productive at the
work place. The technical work of the project involves design of a
technological scenario for the Ambient Intelligence (AmI) - based
assistive technologies at the workplace consisting of an integrated
universal smart solution that suits many different impairment
conditions and will be designed to empower the Physically disabled
persons (PDP) with the capability to access and effectively utilize the
ICTs in order to execute knowledge rich working tasks with
minimum efforts and with sufficient comfort level. The proposed
technology solution for PWD will support voice recognition along
with normal keyboard and mouse to control the smart help and smart
editor with dynamic auto display interface that satisfies the
requirements for different PWD group. In addition, a smart help will
provide intelligent intervention based on the behavior of PWD to
guide them and warn them about possible misbehavior. PWD can
communicate with others using Voice over IP controlled by voice
recognition. Moreover, Auto Emergency Help Response would be
supported to assist PWD in case of emergency. This proposed
technology solution intended to make PWD very effective at the
work environment and flexible using voice to conduct their tasks at
the work environment. The proposed solution aims to provide
favorable outcomes that assist PWD at the work place, with the
opportunity to participate in PWD assistive technology innovation
market which is still small and rapidly growing as well as upgrading
their quality of life to become similar to the normal people at the
workplace. Finally, the proposed smart help solution is applicable in
all workplace setting, including offices, manufacturing, hospital, etc.
Abstract: Excavation and retaining walls are of challenging
issues in civil engineering. In this study, the behavior of one
important type of supporting systems called Contiguous Bored Pile
(CBP) retaining wall is investigated using a physical model. Besides,
a comparison is made between two modes of free end piles (soft bed)
and fixed end piles (stiff bed). Also a back calculation of effective
length (the real free length of pile) is done by measuring lateral
deflection of piles in different stages of excavation in both
aforementioned cases. Based on observed results, for the fixed end
mode, the effective length to free length ratio (Leff/L0) is equal to
unity in initial stages of excavation and less than 1 in its final stages
in a decreasing manner. While this ratio for free end mode, remains
constant during all stages of excavation and is always less than unity.