Abstract: The database reverse engineering problems and
solving processes are getting mature, even though, the academic
community is facing the complex problem of knowledge transfer,
both in university and industrial contexts. This paper presents a new
CASE tool developed at the University of Jordan which addresses an
efficient support of this transfer, namely UJ-CASE-TOOL. It is a
small and self-contained application exhibiting representative
problems and appropriate solutions that can be understood in a
limited time. It presents an algorithm that describes the developed
academic CASE tool which has been used for several years both as
an illustration of the principles of database reverse engineering and
as an exercise aimed at academic and industrial students.
Abstract: This paper presents a method of reducing the feedback
delay time of DWA(Data Weighted Averaging) used in sigma-delta
modulators. The delay time reduction results from the elimination of
the latch at the quantizer output and also from the falling edge
operation. The designed sigma-delta modulator improves the timing
margin about 16%. The sub-circuits of sigma-delta modulator such as
SC(Switched Capacitor) integrator, 9-level quantizer, comparator, and
DWA are designed with the non-ideal characteristics taken into
account. The sigma-delta modulator has a maximum SNR (Signal to
Noise Ratio) of 84 dB or 13 bit resolution.
Abstract: One of the most attractive and important field of chaos theory is control of chaos. In this paper, we try to present a simple framework for chaotic motion control using the feedback linearization method. Using this approach, we derive a strategy, which can be easily applied to the other chaotic systems. This task presents two novel results: the desired periodic orbit need not be a solution of the original dynamics and the other is the robustness of response against parameter variations. The illustrated simulations show the ability of these. In addition, by a comparison between a conventional state feedback and our proposed method it is demonstrated that the introduced technique is more efficient.
Abstract: We present here the results for a comparative study of
some techniques, available in the literature, related to the relevance
feedback mechanism in the case of a short-term learning. Only one
method among those considered here is belonging to the data mining
field which is the K-nearest neighbors algorithm (KNN) while the
rest of the methods is related purely to the information retrieval field
and they fall under the purview of the following three major axes:
Shifting query, Feature Weighting and the optimization of the
parameters of similarity metric. As a contribution, and in addition to
the comparative purpose, we propose a new version of the KNN
algorithm referred to as an incremental KNN which is distinct from
the original version in the sense that besides the influence of the
seeds, the rate of the actual target image is influenced also by the
images already rated. The results presented here have been obtained
after experiments conducted on the Wang database for one iteration
and utilizing color moments on the RGB space. This compact
descriptor, Color Moments, is adequate for the efficiency purposes
needed in the case of interactive systems. The results obtained allow
us to claim that the proposed algorithm proves good results; it even
outperforms a wide range of techniques available in the literature.
Abstract: This paper presents how the real-time chatter
prevention can be realized by feedback of acoustic cutting signal, and
the efficacy of the proposed adaptive spindle speed tuning algorithm is
verified by intensive experimental simulations. A pair of
microphones, perpendicular to each other, is used to acquire the
acoustic cutting signal resulting from milling chatter. A real-time
feedback control loop is constructed for spindle speed compensation
so that the milling process can be ensured to be within the stability
zone of stability lobe diagram. Acoustic Chatter Signal Index (ACSI)
and Spindle Speed Compensation Strategy (SSCS) are proposed to
quantify the acoustic signal and actively tune the spindle speed
respectively. By converting the acoustic feedback signal into ACSI,
an appropriate Spindle Speed Compensation Rate (SSCR) can be
determined by SSCS based on real-time chatter level or ACSI.
Accordingly, the compensation command, referred to as Added-On
Voltage (AOV), is applied to increase/decrease the spindle motor
speed. By inspection on the precision and quality of the workpiece
surface after milling, the efficacy of the real-time chatter prevention
strategy via acoustic signal feedback is further assured.
Abstract: Computer-mediated communication technologies which provide for virtual communities have typically evolved in a cross-dichotomous manner, such that technical constructs of the technology have evolved independently from the social environment of the community. The present paper analyses some limitations of current implementations of computer-mediated communication technology that are implied by such a dichotomy, and discusses their inhibiting effects on possible developments of virtual communities. A Socio-Technical Indicator Model is introduced that utilizes integrated feedback to describe, simulate and operationalise increasing representativeness within a variety of structurally and parametrically diverse systems. In illustration, applications of the model are briefly described for financial markets and for eco-systems. A detailed application is then provided to resolve the aforementioned technical limitations of moderation on the evolution of virtual communities. The application parameterises virtual communities to function as self-transforming social-technical systems which are sensitive to emergent and shifting community values as products of on-going communications within the collective.
Abstract: This paper discusses site selection process for
biological soil conservation planning. It was supported by a valuefocused
approach and spatial multi-criteria evaluation techniques. A
first set of spatial criteria was used to design a number of potential
sites. Next, a new set of spatial and non-spatial criteria was
employed, including the natural factors and the financial costs,
together with the degree of suitability for the Bonkuh watershed to
biological soil conservation planning and to recommend the most
acceptable program. The whole process was facilitated by a new
software tool that supports spatial multiple criteria evaluation, or
SMCE in GIS software (ILWIS). The application of this tool,
combined with a continual feedback by the public attentions, has
provided an effective methodology to solve complex decisional
problem in biological soil conservation planning.
Abstract: In this paper we present an energy efficient match-line
(ML) sensing scheme for high-speed ternary content-addressable
memory (TCAM). The proposed scheme isolates the sensing unit of
the sense amplifier from the large and variable ML capacitance. It
employs feedback in the sense amplifier to successfully detect a
match while keeping the ML voltage swing low. This reduced voltage
swing results in large energy saving. Simulation performed using
130nm 1.2V CMOS logic shows at least 30% total energy saving in
our scheme compared to popular current race (CR) scheme for
similar search speed. In terms of speed, dynamic energy, peak power
consumption and transistor count our scheme also shows better
performance than mismatch-dependant (MD) power allocation
technique which also employs feedback in the sense amplifier.
Additionally, the implementation of our scheme is simpler than CR
or MD scheme because of absence of analog control voltage and
programmable delay circuit as have been used in those schemes.
Abstract: The current paper presents the findings of a research
study on learners- barriers and motivators engaged into blended
programs in a workplace context. In this study, the participants were
randomly assigned to one of four parallel e-learning courses, each of
which was delivered using a different learning strategy. Data were
collected through web-based and telephone surveys developed by the
researchers. The results showed that vague instruction, time
management, and insufficient feedback were the top-most barriers to
blended learning. The major motivators for blended learning included
content relevance, flexibility in time, and the ability to work at own
pace.
Abstract: In the present work, an attempt has been made to
understand the feasibility of using UHF technique for identification
of any corona discharges/ arcing in insulating material due to water
droplets. The sensors of broadband type are useful for identification
of such discharges. It is realised that arcing initiated by liquid droplet
radiates UHF signals in the entire bandwidth up to 2 GHz. The
frequency content of the UHF signal generated due to corona/arcing
is not much varied in epoxy nanocomposites with different weight
percentage of clay content. The exfoliated/intercalated properties
were analysed through TEM studies. It is realized that corona
initiated discharges are of intermittent process. The hydrophobicity
of the material characterized through contact angle measurement. It
is realized that low Wt % of nanoclay content in epoxy resin reduces
the surface carbonization due to arcing/corona discharges. The results
of the study with gamma irradiated specimen indicates that contact
angle, discharge inception time and evaporation time of the liquid are
much lower than the virgin epoxy nanocomposite material.
Abstract: The IEEE802.16 standard which has emerged as
Broadband Wireless Access (BWA) technology, promises to deliver
high data rate over large areas to a large number of subscribers in the
near future. This paper analyze the effect of overheads over capacity
of downlink (DL) of orthogonal frequency division multiple access
(OFDMA)–based on the IEEE802.16e mobile WiMAX system with
and without overheads. The analysis focuses in particular on the
impact of Adaptive Modulation and Coding (AMC) as well as
deriving an algorithm to determine the maximum numbers of
subscribers that each specific WiMAX sector may support. An
analytical study of the WiMAX propagation channel by using Cost-
231 Hata Model is presented. Numerical results and discussion
estimated by using Matlab to simulate the algorithm for different
multi-users parameters.
Abstract: A model-free robust control (MFRC) approach is proposed for position control of robot manipulators in the state space. The control approach is verified analytically to be robust subject to uncertainties including external disturbances, unmodeled dynamics, and parametric uncertainties. There is a high flexibility to work on different systems including actuators by the use of the proposed control approach. The proposed control approach can guarantee the robustness of control system. A PUMA 560 robot driven by geared permanent magnet dc motors is simulated. The simulation results show a satisfactory performance for control system under technical specifications. KeywordsModel-free, robust control, position control, PUMA 560.
Abstract: In this paper, we propose a robust controller design method for discrete-time systems with sector-bounded nonlinearities and time-varying delay. Based on the Lyapunov theory, delaydependent stabilization criteria are obtained in terms of linear matrix inequalities (LMIs) by constructing the new Lyapunov-Krasovskii functional and using some inequalities. A robust state feedback controller is designed by LMI framework and a reciprocally convex combination technique. The effectiveness of the proposed method is verified throughout a numerical example.
Abstract: Powerline Communications –PLC– as an alternative
method for broadband networking, has the advantage of transmitting
over channels already used for electrical distribution or even
transmission. But these channels have been not designed with usual
wired channels requirements for broadband applications such as
stable impedance or known attenuation, and the network have to
reject noises caused by electrical appliances that share the same
channel. Noise control standards are difficult to complain or simply
do not exist on Latin-American environments. This paper analyzes
PLC throughput for home connectivity by probing noisy channel
scenarios in a PLC network and the statistical results are shown.
Abstract: The seismic feedback experiences in Algeria have
shown higher percentage of damages for non-code conforming
reinforced concrete (RC) buildings. Furthermore, the vulnerability of
these buildings was further aggravated due to presence of many
factors (e.g. weak the seismic capacity of these buildings, shorts
columns, Pounding effect, etc.).
Consequently Seismic risk assessments were carried out on
populations of buildings to identify the buildings most likely to
undergo losses during an earthquake. The results of such studies are
important in the mitigation of losses under future seismic events as
they allow strengthening intervention and disaster management plans
to be drawn up.
Within this paper, the state of the existing structures is assessed using
"the vulnerability index" method. This method allows the
classification of RC constructions taking into account both, structural
and non structural parameters, considered to be ones of the main
parameters governing the vulnerability of the structure. Based on
seismic feedback from past earthquakes DPM (damage probability
matrices) were developed too.
Abstract: This paper presents the development and application of an adaptive neuro fuzzy inference system (ANFIS) based intelligent hybrid neuro fuzzy controller for automatic generation control (AGC) of two-area interconnected thermal power system with reheat non linearity. The dynamic response of the system has been studied for 1% step load perturbation in area-1. The performance of the proposed neuro fuzzy controller is compared against conventional proportional-integral (PI) controller, state feedback linear quadratic regulator (LQR) controller and fuzzy gain scheduled proportionalintegral (FGSPI) controller. Comparative analysis demonstrates that the proposed intelligent neuro fuzzy controller is the most effective of all in improving the transients of frequency and tie-line power deviations against small step load disturbances. Simulations have been performed using Matlab®.
Abstract: In this paper, a fibre laser at 546 nm has been studied
for a signal power of -30 dB. Er3+-doped ZBLAN fibre has been used
by upconversion pumping of a 980 nm laser diode. Gain saturation
effect has been investigated in detail. Laser performance has also been
discussed. An efficiency of 35% has been calculated with a length of 5
mm fibre laser. Results show that Er3+-doped ZBLAN is a promising
candidate for optical amplification at 546 nm.
Abstract: A low cost Short Message System (SMS) based Home security system equipped with motion, smoke, temperature, humidity and light sensors has been studied and tested. The sensors are controlled by a microprocessor PIC 18F4520 through the SMS having password protection code for the secure operation. The user is able to switch light and the appliances and get instant feedback. Also in cases of emergencies such as fire or robbery the system will send alert message to occupant and relevant civil authorities. The operation of the home security has been tested on Vodafone- Fiji network and Digicel Fiji Network for emergency and feedback responses for 25 samples. The experiment showed that it takes about 8-10s for the security system to respond in case of emergency. It takes about 18-22s for the occupant to switch and monitor lights and appliances and then get feedback depending upon the network traffic.
Abstract: In this paper present a sensorless maximum wind power extraction for variable speed constant frequency (VSCF) wind power generation systems with a doubly-fed induction generators (DFIG), to ensure stability and to impose the ideal feedback control solution despite of model uncertainties , using the principles of an active and reactive power controller (DPC) a robust sliding mode power control has been proposed to guarantees fast response times and precise control actions for control the active and reactive power independently. The simulation results in MATLAB/Simulink platform confirmed the good dynamic performance of power control approach for DFIGbased variable speed wind turbines.
Abstract: The Brazilian Agricultural Products Wholesale Market fits well as example of residues generating system, reaching 750 metric tons per month of total residues, from which 600 metric tons are organic material and 150 metric tons are recyclable materials. Organic material is basically composed of fruit, vegetables and flowers leftovers from the products commercialization. The recyclable compounds are generate from packing material employed in the commercialization process. This research work devoted efforts in carrying quantitative analysis of the residues generated in the agricultural enterprise at its final destination. Data survey followed the directions implemented by the Residues Management Program issued by the agricultural enterprise. It was noticed from that analysis the necessity of changing the logistics applied to the recyclable material collecting process. However, composting process was elected as the organic compounds destination which is considered adequate for a material composed of significant percentage of organic matter far higher than wood, cardboard and plastics contents.