Abstract: Applying a rigorous process to optimize the elements
of a supply-chain network resulted in reduction of the waiting time
for a service provider and customer. Different sources of downtime
of hydraulic pressure controller/calibrator (HPC) were causing
interruptions in the operations. The process examined all the issues to
drive greater efficiencies. The issues included inherent design issues
with HPC pump, contamination of the HPC with impurities, and the
lead time required for annual calibration in the USA.
HPC is used for mandatory testing/verification of formation
tester/pressure measurement/logging-while drilling tools by oilfield
service providers, including Halliburton.
After market study andanalysis, it was concluded that the current
HPC model is best suited in the oilfield industry. To use theexisting
HPC model effectively, design andcontamination issues were
addressed through design and process improvements. An optimum
network is proposed after comparing different supply-chain models
for calibration lead-time reduction.
Abstract: Minimum Quantity Lubrication (MQL) technique
obtained a significant attention in machining processes to reduce
environmental loads caused by usage of conventional cutting fluids.
Recently nanofluids are finding an extensive application in the field
of mechanical engineering because of their superior lubrication and
heat dissipation characteristics. This paper investigates the use of a
nanofluid under MQL mode to improve grinding characteristics of
Ti-6Al-4V alloy. Taguchi-s experimental design technique has been
used in the present investigation and a second order model has been
established to predict grinding forces and surface roughness.
Different concentrations of water based Al2O3 nanofluids were
applied in the grinding operation through MQL setup developed in
house and the results have been compared with those of conventional
coolant and pure water. Experimental results showed that grinding
forces reduced significantly when nano cutting fluid was used even at
low concentration of the nano particles and surface finish has been
found to improve with higher concentration of the nano particles.
Abstract: Iran is one of the greatest producers of date in the
world. However due to lack of information about its viscoelastic
properties, much of the production downgraded during harvesting
and postharvesting processes. In this study the effect of temperature
and moisture content of product were investigated on stress
relaxation characteristics. Therefore, the freshly harvested date
(kabkab) at tamar stage were put in controlled environment chamber
to obtain different temperature levels (25, 35, 45, and 55 0C) and
moisture contents (8.5, 8.7, 9.2, 15.3, 20, 32.2 %d.b.). A texture
analyzer TAXT2 (Stable Microsystems, UK) was used to apply
uniaxial compression tests. A chamber capable to control temperature
was designed and fabricated around the plunger of texture analyzer to
control the temperature during the experiment. As a new approach a
CCD camera (A4tech, 30 fps) was mounted on a cylindrical glass
probe to scan and record contact area between date and disk.
Afterwards, pictures were analyzed using image processing toolbox
of Matlab software. Individual date fruit was uniaxially compressed
at speed of 1 mm/s. The constant strain of 30% of thickness of date
was applied to the horizontally oriented fruit. To select a suitable
model for describing stress relaxation of date, experimental data were
fitted with three famous stress relaxation models including the
generalized Maxwell, Nussinovitch, and Pelege. The constant in
mentioned model were determined and correlated with temperature
and moisture content of product using non-linear regression analysis.
It was found that Generalized Maxwell and Nussinovitch models
appropriately describe viscoelastic characteristics of date fruits as
compared to Peleg mode.
Abstract: The ideal sinc filter, ignoring the noise statistics, is often
applied for generating an arbitrary sample of a bandlimited signal by
using the uniformly sampled data. In this article, an optimal interpolator is proposed; it reaches a minimum mean square error (MMSE)
at its output in the presence of noise. The resulting interpolator is
thus a Wiener filter, and both the optimal infinite impulse response
(IIR) and finite impulse response (FIR) filters are presented. The
mean square errors (MSE-s) for the interpolator of different length
impulse responses are obtained by computer simulations; it shows that
the MSE-s of the proposed interpolators with a reasonable length are
improved about 0.4 dB under flat power spectra in noisy environment with signal-to-noise power ratio (SNR) equal 10 dB. As expected,
the results also demonstrate the improvements for the MSE-s with various fractional delays of the optimal interpolator against the ideal
sinc filter under a fixed length impulse response.
Abstract: Lean production (or lean management respectively)
gained popularity in several waves. The last three decades have been
filled with numerous attempts to apply these concepts in companies.
However, this has only been partially successful. The roots of lean
production can be traced back to Toyota-s just-in-time production.
This concept, which according to Womack-s, Jones- and Roos-
research at MIT was employed by Japanese car manufacturers,
became popular under its international names “lean production",
“lean-manufacturing" and was termed “Schlanke Produktion" in
Germany. This contribution shows a review about lean production in
Germany over the last thirty years: development, trial & error and
implementation as well.
Abstract: One of the biggest drawbacks of the wireless
environment is the limited bandwidth. However, the users sharing
this limited bandwidth have been increasing considerably. SDMA
technique which entails using directional antennas allows to increase
the capacity of a wireless network by separating users in the medium.
In this paper, it has been presented how the capacity can be enhanced
while the mean delay is reduced by using directional antennas in
wireless networks employing TDMA/FDD MAC. Computer
modeling and simulation of the wireless system studied are realized
using OPNET Modeler. Preliminary simulation results are presented
and the performance of the model using directional antennas is
evaluated and compared consistently with the one using
omnidirectional antennas.
Abstract: This paper discusses a new model of Islamic code of
ethics for directors. Several corporate scandals and local (example
Transmile and Megan Media) and overseas corporate (example
Parmalat and Enron) collapses show that the current corporate
governance and regulatory reform are unable to prevent these events
from recurring. Arguably, the code of ethics for directors is under
research and the current code of ethics only concentrates on binding
the work of the employee of the organization as a whole, without
specifically putting direct attention to the directors, the group of
people responsible for the performance of the company. This study
used a semi-structured interview survey of well-known Islamic
scholars such as the Mufti to develop the model. It is expected that
the outcome of the research is a comprehensive model of code of
ethics based on the Islamic principles that can be applied and used by
the company to construct a code of ethics for their directors.
Abstract: In this research, the use of light beam size to design the adjustable mirror bender is presented. The focused beam line characterized by its size towards the synchrotron light beam line is investigated. The COSMOSWorks is used in all simulation components of curvature adjustment system to analyze in finite element method. The results based on simulation covers the use of applied forces during adjustment of the mirror radius are presented.
Abstract: This paper and its companion (Part 2) deal with
modeling and optimization of two NP-hard problems in production
planning of flexible manufacturing system (FMS), part type selection
problem and loading problem. The part type selection problem and
the loading problem are strongly related and heavily influence the
system-s efficiency and productivity. The complexity of the problems
is harder when flexibilities of operations such as the possibility of
operation processed on alternative machines with alternative tools are
considered. These problems have been modeled and solved
simultaneously by using real coded genetic algorithms (RCGA)
which uses an array of real numbers as chromosome representation.
These real numbers can be converted into part type sequence and
machines that are used to process the part types. This first part of the
papers focuses on the modeling of the problems and discussing how
the novel chromosome representation can be applied to solve the
problems. The second part will discuss the effectiveness of the
RCGA to solve various test bed problems.
Abstract: Image restoration involves elimination of noise. Filtering techniques were adopted so far to restore images since last five decades. In this paper, we consider the problem of image restoration degraded by a blur function and corrupted by random noise. A method for reducing additive noise in images by explicit analysis of local image statistics is introduced and compared to other noise reduction methods. The proposed method, which makes use of an a priori noise model, has been evaluated on various types of images. Bayesian based algorithms and technique of image processing have been described and substantiated with experimentation using MATLAB.
Abstract: Human amniotic membrane (HAM) is a useful
biological material for the reconstruction of damaged ocular surface.
The processing and preservation of HAM is critical to prevent the
patients undergoing amniotic membrane transplant (AMT) from cross
infections. For HAM preparation human placenta is obtained after an
elective cesarean delivery. Before collection, the donor is screened
for seronegativity of HCV, Hbs Ag, HIV and Syphilis. After
collection, placenta is washed in balanced salt solution (BSS) in
sterile environment. Amniotic membrane is then separated from the
placenta as well as chorion while keeping the preparation in BSS.
Scrapping of HAM is then carried out manually until all the debris is
removed and clear transparent membrane is acquired. Nitrocellulose
membrane filters are then placed on the stromal side of HAM, cut
around the edges with little membrane folded towards other side
making it easy to separate during surgery. HAM is finally stored in
solution of glycerine and Dulbecco-s Modified Eagle Medium
(DMEM) in 1:1 ratio containing antibiotics. The capped borosil vials
containing HAM are kept at -80°C until use. This vial is thawed to
room temperature and opened under sterile operation theatre
conditions at the time of surgery.
Abstract: In the present paper, the three-dimensional
temperature field of tool is determined during the machining and
compared with experimental work on C45 workpiece using carbide
cutting tool inserts. During the metal cutting operations, high
temperature is generated in the tool cutting edge which influence on
the rate of tool wear. Temperature is most important characteristic of
machining processes; since many parameters such as cutting speed,
surface quality and cutting forces depend on the temperature and high
temperatures can cause high mechanical stresses which lead to early
tool wear and reduce tool life. Therefore, considerable attention is
paid to determine tool temperatures. The experiments are carried out
for dry and orthogonal machining condition. The results show that
the increase of tool temperature depends on depth of cut and
especially cutting speed in high range of cutting conditions.
Abstract: Physiological activity of the pineal gland with specific
responses in the reproductive territory may be interpreted by
monitoring the process parameters used in poultry practice in
different age batches of laying hens. As biological material were
used 105 laying hens, clinically healthy, belonging to ALBO SL-
2000 hybrid, raised on ground, from which blood samples were taken
at the age of 12 and 28 weeks. The haematological examinations
were concerned to obtain the total number of erythrocytes and
leukocytes and the main erythrocyte constant (RBC, PCV, MCV,
MCH, MCHC and WBC). The results allow the interpretation of the
reproductive status through the dynamics of the presented values.
Abstract: Many factors affect the success of Machine Learning
(ML) on a given task. The representation and quality of the instance
data is first and foremost. If there is much irrelevant and redundant
information present or noisy and unreliable data, then knowledge
discovery during the training phase is more difficult. It is well known
that data preparation and filtering steps take considerable amount of
processing time in ML problems. Data pre-processing includes data
cleaning, normalization, transformation, feature extraction and
selection, etc. The product of data pre-processing is the final training
set. It would be nice if a single sequence of data pre-processing
algorithms had the best performance for each data set but this is not
happened. Thus, we present the most well know algorithms for each
step of data pre-processing so that one achieves the best performance
for their data set.
Abstract: Lean manufacturing is a production philosophy made
popular by Toyota Motor Corporation (TMC). It is globally known as
the Toyota Production System (TPS) and has the ultimate aim of
reducing cost by thoroughly eliminating wastes or muda. TPS
embraces the Just-in-time (JIT) manufacturing; achieving cost
reduction through lead time reduction. JIT manufacturing can be
achieved by implementing Pull system in the production.
Furthermore, TPS aims to improve productivity and creating
continuous flow in the production by arranging the machines and
processes in cellular configurations. This is called as Cellular
Manufacturing Systems (CMS). This paper studies on integrating the
CMS with the Pull system to establish a Big Island-Pull system
production for High Mix Low Volume (HMLV) products in an
automotive component industry. The paper will use the build-in JIT
system steps adapted from TMC to create the Pull system production
and also create a shojinka line which, according to takt time, has the
flexibility to adapt to demand changes simply by adding and taking
out manpower. This will lead to optimization in production.
Abstract: Recently research on human wayfinding has focused
mainly on mental representations rather than processes of
wayfinding. The objective of this paper is to demonstrate the
rationality behind applying multi-agent simulation paradigm to the
modeling of rescuer team wayfinding in order to develop
computational theory of perceptual wayfinding in crisis situations
using image schemata and affordances, which explains how people
find a specific destination in an unfamiliar building such as a
hospital. The hypothesis of this paper is that successful navigation is
possible if the agents are able to make the correct decision through
well-defined cues in critical cases, so the design of the building
signage is evaluated through the multi-agent-based simulation. In
addition, a special case of wayfinding in a building, finding one-s
way through three hospitals, is used to demonstrate the model.
Thereby, total rescue time for rescue operation during building fire is
computed. This paper discuses the computed rescue time for various
signage localization and provides experimental result for
optimization of building signage design. Therefore the most
appropriate signage design resulted in the shortest total rescue time in
various situations.
Abstract: this study was carried out to investigate the changes in
quality parameters of rye bread packaged in different polymer films
during convection air-flow thermal treatment process. Whole loafs of
bread were placed in polymer pouches, which were sealed in reduced
pressure air ambiance, bread was thermally treated in
at temperature +(130; 140; and 150) ± 5 ºC within 40min, as long as
the core temperature of the samples have reached accordingly
+80±1 ºC. For bread packaging pouches were used: anti-fog
Mylar®OL12AF and thermo resistant combined polymer material.
Main quality parameters was analysed using standard methods:
temperature in bread core, bread crumb and crust firmness value,
starch granules volume and microflora. In the current research it was
proved, that polymer films significantly influence rye bread quality
parameters changes during thermal treatment. Thermo resistant
combined polymer material film could be recommendable for
packaged rye bread pasteurization, for maximal bread quality
parameter keeping.
Abstract: Rule Discovery is an important technique for mining
knowledge from large databases. Use of objective measures for
discovering interesting rules leads to another data mining problem,
although of reduced complexity. Data mining researchers have
studied subjective measures of interestingness to reduce the volume
of discovered rules to ultimately improve the overall efficiency of
KDD process.
In this paper we study novelty of the discovered rules as a
subjective measure of interestingness. We propose a hybrid approach
based on both objective and subjective measures to quantify novelty
of the discovered rules in terms of their deviations from the known
rules (knowledge). We analyze the types of deviation that can arise
between two rules and categorize the discovered rules according to
the user specified threshold. We implement the proposed framework
and experiment with some public datasets. The experimental results
are promising.
Abstract: The automatic transmission (AT) is one of the most
important components of many automobile transmission systems. The
shift quality has a significant influence on the ride comfort of the
vehicle. During the AT shift process, the joint elements such as the
clutch and bands engage or disengage, linking sets of gears to create a
fixed gear ratio. Since these ratios differ between gears in a fixed gear
ratio transmission, the motion of the vehicle could change suddenly
during the shift process if the joint elements are engaged or disengaged
inappropriately, additionally impacting the entire transmission system
and increasing the temperature of connect elements.The objective was
to establish a system model for an AT powertrain using
Matlab/Simulink. This paper further analyses the effect of varying
hydraulic pressure and the associated impact on shift quality during
both engagment and disengagement of the joint elements, proving that
shift quality improvements could be achieved with appropriate
hydraulic pressure control.
Abstract: This research focuses on the effect of weight
percentage variation and size variation of MgFeSi added,
gating system design and reaction chamber design on inmold
process. By using inmold process, well-known problem of
fading is avoided because the liquid iron reacts with
magnesium in the mold and not, as usual, in the ladle. During
the pouring operation, liquid metal passes through the
chamber containing the magnesium, where the reaction of the
metal with magnesium proceeds in the absence of atmospheric
oxygen [1].In this paper, the results of microstructural
characteristic of ductile iron on this parameters are mentioned.
The mechanisms of the inmold process are also described [2].
The data obtained from this research will assist in producing
the vehicle parts and other machinery parts for different
industrial zones and government industries and in transferring
the technology to all industrial zones in Myanmar. Therefore,
the inmold technology offers many advantages over traditional
treatment methods both from a technical and environmental,
as well as an economical point of view. The main objective of
this research is to produce ductile iron castings in all industrial
sectors in Myanmar more easily with lower costs. It will also
assist the sharing of knowledge and experience related to the
ductile iron production.