Abstract: The Yasuj city stream named the Beshar supply
water for different usages such as aquaculture farms , drinking,
agricultural and industrial usages. Fish processing plants
,Agricultural farms, waste water of industrial zones and hospitals
waste water which they are generate by human activity produce a
considerable volume of effluent and when they are released in to the
stream they can effect on the water quality and down stream aquatic
systems. This study was conducted to evaluate the effects of outflow
effluent from different human activity and point and non point
pollution sources on the water quality and health of the Beshar
river next to Yasuj. Yasuj is the biggest and most important city in
the Kohkiloye and Boyerahmad province . The Beshar River is one
of the most important aquatic ecosystems in the upstream of the
Karun watershed in south of Iran which is affected by point and non
point pollutant sources . This study was done in order to evaluate the
effects of human activities on the water quality and health of the
Beshar river. This river is approximately 190 km in length and
situated at the geographical positions of 51° 20' to 51° 48' E and 30°
18' to 30° 52' N it is one of the most important aquatic ecosystems of
Kohkiloye and Boyerahmad province in south-west Iran. In this
research project, five study stations were selected to examine water
pollution in the Beshar River systems. Human activity is now one of
the most important factors affecting on hydrology and water quality
of the Beshar river. Humans use large amounts of resources to sustain
various standards of living, although measures of sustainability are
highly variable depending on how sustainability is defined. The
Beshar river ecosystems are particularly sensitive and vulnerable to
human activities. The water samples were analyzed, then some
important water quality parameters such as pH, dissolve oxygen
(DO), Biochemical Oxygen Demand (BOD5), Chemical Oxygen
Demand (COD), Total Suspended Solids (TDS),Turbidity,
Temperature, Nitrates (NO3) and Phosphates (PO4) were estimated
at the two stations. The results show a downward trend in the water
quality at the down stream of the city. The amounts of
BOD5,COD,TSS,T,Turbidity, NO3 and PO4 in the down stream
stations were considerably more than the station 1. By contrast the
amounts of DO in the down stream stations were less than to the
station 1. However when effluent discharge consequence of human
activities are released into the Beshar river near the city, the quality
of river are decreases and the environmental problems of the river
during the next years are predicted to rise.
Abstract: Shadows add great amount of realism to a scene and
many algorithms exists to generate shadows. Recently, Shadow
volumes (SVs) have made great achievements to place a valuable
position in the gaming industries. Looking at this, we concentrate on
simple but valuable initial partial steps for further optimization in SV
generation, i.e.; model simplification and silhouette edge detection
and tracking. Shadow volumes (SVs) usually takes time in generating
boundary silhouettes of the object and if the object is complex then
the generation of edges become much harder and slower in process.
The challenge gets stiffer when real time shadow generation and
rendering is demanded. We investigated a way to use the real time
silhouette edge detection method, which takes the advantage of
spatial and temporal coherence, and exploit the level-of-details
(LOD) technique for reducing silhouette edges of the model to use
the simplified version of the model for shadow generation speeding
up the running time. These steps highly reduce the execution time of
shadow volume generations in real-time and are easily flexible to any
of the recently proposed SV techniques. Our main focus is to exploit
the LOD and silhouette edge detection technique, adopting them to
further enhance the shadow volume generations for real time
rendering.
Abstract: Pressures for urban redevelopment are intensifying in
all large cities. A new logic for urban development is required –
green urbanism – that provides a spatial framework for directing
population and investment inwards to brownfields and greyfields
precincts, rather than outwards to the greenfields. This represents
both a major opportunity and a major challenge for city planners in
pluralist liberal democracies. However, plans for more compact
forms of urban redevelopment are stalling in the face of community
resistance. A new paradigm and spatial planning platform is required
that will support timely multi-level and multi-actor stakeholder
engagement, resulting in the emergence of consensus plans for
precinct-level urban regeneration capable of more rapid
implementation. Using Melbourne, Australia as a case study, this
paper addresses two of the urban intervention challenges – where and
how – via the application of a 21st century planning tool ENVISION
created for this purpose.
Abstract: One of the main problems of suspended cable structures is initial shape change under the action of non uniform load. The problem can be solved by increasing of weight of construction or by using of prestressing. But this methods cause increasing of materials consumption of suspended cable structure. The cable truss usage is another way how the problem of shape change under the action of non uniform load can be fixed. The cable trusses with the vertical and inclined suspensions, cross web and single cable were analyzed as the main load-bearing structures of suspension bridge. It was shown, that usage of cable truss allows to reduce the vertical displacements up to 32% in comparison with the single cable in case of non uniformly distributed load. In case of uniformly distributed load single cable is preferable.
Abstract: The main goal of the study is to analyze all relevant properties of the electro hydraulic systems and based on that to make a proper choice of the neural network control strategy that may be used for the control of the mechatronic system. A combination of electronic and hydraulic systems is widely used since it combines the advantages of both. Hydraulic systems are widely spread because of their properties as accuracy, flexibility, high horsepower-to-weight ratio, fast starting, stopping and reversal with smoothness and precision, and simplicity of operations. On the other hand, the modern control of hydraulic systems is based on control of the circuit fed to the inductive solenoid that controls the position of the hydraulic valve. Since this circuit may be easily handled by PWM (Pulse Width Modulation) signal with a proper frequency, the combination of electrical and hydraulic systems became very fruitful and usable in specific areas as airplane and military industry. The study shows and discusses the experimental results obtained by the control strategy of neural network control using MATLAB and SIMULINK [1]. Finally, the special attention was paid to the possibility of neuro-controller design and its application to control of electro-hydraulic systems and to make comparative with other kinds of control.
Abstract: Plants are rich sources of bioactive compounds. In this study the photochemical screening of hexane, ethanolic and aqueous extracts of roots and latex of jojoba (Simmondsia chinensis) plant revealed the presence of saponins, tannins, alkaloids, steroids and glycosides. Ethanolic extract was found to be richer in these metabolites than hexane, aqueous extracts and latex. The extracts and latex displayed effective antimicrobial activity against Salmonella typhimurium, Bacillus cereus, Clostridium perfringens, Staphylococcus aureus, Escherichia coli, Candida albicans and Aspergillus flavus. The increase in volume of the extracts and latex caused more activity, as shown by zones of inhibition. Candida albicans growth was inhibited only by hexane extract. Jojoba latex was not effective against Candida albicans at 0.1 and 0.5 ml extracts concentration but showed 5mm zone of inhibition at (1.0 ml). Lower volume (0.1ml) of latex encouraged Aspergillus flavus growth, while at (1.00 ml) reduced its mycelial growth. Thus, jojoba root extracts and latex can be of potential natural antimicrobial agents.
Abstract: In this paper the Analytic Network Process (ANP) is
applied to the selection of photovoltaic (PV) solar power projects.
These projects follow a long management and execution process
from plant site selection to plant start-up. As a consequence, there are
many risks of time delays and even of project stoppage.
In the case study presented in this paper a top manager of an
important Spanish company that operates in the power market has to
decide on the best PV project (from four alternative projects) to
invest based on risk minimization. The manager identified 50 project
execution delay and/or stoppage risks.
The influences among elements of the network (groups of risks
and alternatives) were identified and analyzed using the ANP
multicriteria decision analysis method. After analyzing the results the
main conclusion is that the network model can manage all the
information of the real-world problem and thus it is a decision
analysis model recommended by the authors. The strengths and
weaknesses ANP as a multicriteria decision analysis tool are also
described in the paper.
Abstract: In this paper we are interested in Moufang-Klingenberg
planesM(A) defined over a local alternative ring A of dual numbers.
We introduce two new collineations of M(A).
Abstract: COPD is characterized by loss of elastic fibers from
small airways and alveolar walls, with the decrease in elastin
increasing with disease severity. It is unclear why there is a lack of
repair of elastic fibers. We have examined fibroblasts cultured from
lung tissue from normal and COPD subjects to determine if the
secretory profile explains lack of tissue repair. In this study,
fibroblasts were cultured from lung parenchyma of bronchial
carcinoma patients with varying degrees of COPD; controls
(non-COPD, n=5), mild COPD (GOLD 1, n=5) and moderate-severe
COPD (GOLD 2-3, n=12). Measurements were made of proliferation,
senescence-associated beta-galactosidase-1, mRNA expression of
IL-6, IL-8, MMP-1, tropoelastin and versican, and protein levels for
IL-6, IL-8, PGE2, tropoelastin, insoluble elastin, and versican. It was
found that GOLD 2-3 fibroblasts proliferated more slowly (p
Abstract: This paper presents a part of research on the
rheological properties of bitumen modified by thermoplastic namely
linear low density polyethylene (LLDPE), high density polyethylene
(HDPE) and polypropylene (PP) and its interaction with 80 pen base
bitumen. As it is known that the modification of bitumen by the use
of polymers enhances its performance characteristics but at the same
time significantly alters its rheological properties. The rheological
study of polymer modified bitumen (PMB) was made through
penetration, ring & ball softening point and viscosity test. The results
were then related to the changes in the rheological properties of
polymer modified bitumen. It was observed that thermoplastic
copolymer shows profound effect on penetration rather than
softening point. The viscoelastic behavior of polymer modified
bitumen depend on the concentration of polymer, mixing
temperature, mixing technique, solvating power of base bitumen and
molecular structure of polymer used. PP offer better blend in
comparison to HDPE and LLDPE. The viscosity of base bitumen was
also enhanced with the addition of polymer. The pseudoplastic
behavior was more prominent for HDPE and LLDPE than PP. Best
results were obtained when polymer concentration was kept below
3%
Abstract: Optical properties of sputter-deposited ZnS thin films
were investigated as potential replacements for CBD(chemical bath
deposition) CdS buffer layers in the application of CIGS solar cells.
ZnS thin films were fabricated on glass substrates at RT, 150oC, 200oC,
and 250oC with 50 sccm Ar gas using an RF magnetron sputtering
system. The crystal structure of the thin film is found to be zinc blende
(cubic) structure. Lattice parameter of ZnS is slightly larger than CdS
on the plane and thus better matched with that of CIGS. Within a
400-800 nm wavelength region, the average transmittance was larger
than 75%. When the deposition temperature of the thin film was
increased, the blue shift phenomenon was enhanced. Band gap energy
of the ZnS thin film tended to increase as the deposition temperature
increased. ZnS thin film is a promising material system for the CIGS
buffer layer, in terms of ease of processing, low cost, environmental
friendliness, higher transparency, and electrical properties
Abstract: Measurement of the quality of image compression is important for image processing application. In this paper, we propose an objective image quality assessment to measure the quality of gray scale compressed image, which is correlation well with subjective quality measurement (MOS) and least time taken. The new objective image quality measurement is developed from a few fundamental of objective measurements to evaluate the compressed image quality based on JPEG and JPEG2000. The reliability between each fundamental objective measurement and subjective measurement (MOS) is found. From the experimental results, we found that the Maximum Difference measurement (MD) and a new proposed measurement, Structural Content Laplacian Mean Square Error (SCLMSE), are the suitable measurements that can be used to evaluate the quality of JPEG200 and JPEG compressed image, respectively. In addition, MD and SCLMSE measurements are scaled to make them equivalent to MOS, given the rate of compressed image quality from 1 to 5 (unacceptable to excellent quality).
Abstract: The substrate heater designed for this investigation is a front side substrate heating system. It consists of 10 conventional tungsten halogen lamps and an aluminum reflector, total input electrical power of 5 kW. The substrate is heated by means of a radiation from conventional tungsten halogen lamps directed to the substrate through a glass window. This design allows easy replacement of the lamps and maintenance of the system. Within 2 to 6 minutes the substrate temperature reaches 500 to 830 C by varying the vertical distance between the glass window and the substrate holder. Moreover, the substrate temperature can be easily controlled by controlling the input power to the system. This design gives excellent opportunity to deposit many deferent films at deferent temperatures in the same deposition time. This substrate heater was successfully used for Chemical Vapor Deposition (CVD) of many thin films, such as Silicon, iron, etc.
Abstract: Mycotoxin (aflatoxins) contamination of peanuts is a
great concern for human health. A total of 72 samples of unripe,
roasted, and salty peanuts were collected randomly from Pothohar
plateau of Pakistan for the assessment of aflatoxin. Samples were
dried, ground and extracted by acetonitrile (84%). The filtered
extracts were cleaned up by MycoSep-226 and analyzed by high
performance liquid chromatography with flourescence detector.
Quantification limit of Aflatoxin was 1 μg/kg and 70% Recovery was
observed in spiked samples in the range 1–10 μg/kg. The screening
of mycotoxins indicated that aflatoxins were present in most of the
samples being detected in 82%, in concentrations from 14.25 μg/kg
to 98.80 μg/kg. Optimal conditions for mycotoxin production and
fungal growth are frequently found in the crop fields as well as in
store houses. Human exposure of such toxin can be controlled by
pointed out such awareness and implemented the regulations.
Abstract: In the present study, the effect of ferrous sulfate concentration and total solids on bioleaching of heavy metals from sewage sludge has been examined using indigenous iron-oxidizing microorganisms. The experiments on effects of ferrous sulfate concentrations on bioleaching were carried out using ferrous sulfate of different concentrations (5-20 g L-1) to optimize the concentration of ferrous sulfate for maximum bioleaching. A rapid change in the pH and ORP took place in first 2 days followed by a slow change till 16th day in all the sludge samples. A 10 g L-1 ferrous sulfate concentration was found to be sufficient in metal bioleaching in the following order: Zn: 69%>Cu: 52%>Cr: 46%>Ni: 45. Further, bioleaching using 10 g/L ferrous sulfate was found to be efficient up to 20 g L-1 sludge solids concentration. The results of the present study strongly indicate that using 10 g L-1 ferrous sulfate indigenous iron-oxidizing microorganisms can bring down pH to a value needed for significant metal solubilization.
Abstract: The procurement and cost management approach adopted for mechanical and electrical (M&E) services in Malaysian construction industry have been criticized for its inefficiency. The study examined early cost estimating practices adopted for mechanical and electrical services (M&E) in Malaysia so as to understand the level of compliance of the current techniques with best practices. The methodology adopted for the study is a review of bidding documents used on both completed and on – going building projects awarded between 2008 – 2010 under 9th Malaysian Plan. The analysis revealed that, M&E services cost cannot be reliably estimated at pre-contract stage; the bidding techniques adopted for M&E services failed to provide uniform basis for contractors to submit tender; detailed measurement of items were not made which could complicate post contract cost control and financial management. The paper concluded that, there is need to follow a structured approach in determining the pre-contract cost estimate for M&E services which will serve as a virile tool for post contract cost control.
Abstract: The use of new technologies such internet (e-mail, chat
rooms) and cell phones has steeply increased in recent years.
Especially among children and young people, use of technological
tools and equipments is widespread. Although many teachers and
administrators now recognize the problem of school bullying, few are
aware that students are being harassed through electronic
communication. Referred to as electronic bullying, cyber bullying, or
online social cruelty, this phenomenon includes bullying through email,
instant messaging, in a chat room, on a website, or through
digital messages or images sent to a cell phone. Cyber bullying is
defined as causing deliberate/intentional harm to others using internet
or other digital technologies. It has a quantitative research design nd
uses relational survey as its method. The participants consisted of
300 secondary school students in the city of Konya, Turkey. 195
(64.8%) participants were female and 105 (35.2%) were male. 39
(13%) students were at grade 1, 187 (62.1%) were at grade 2 and 74
(24.6%) were at grade 3. The “Cyber Bullying Question List"
developed by Ar─▒cak (2009) was given to students. Following
questions about demographics, a functional definition of cyber
bullying was provided. In order to specify students- human values,
“Human Values Scale (HVS)" developed by Dilmaç (2007) for
secondary school students was administered. The scale consists of 42
items in six dimensions. Data analysis was conducted by the primary
investigator of the study using SPSS 14.00 statistical analysis
software. Descriptive statistics were calculated for the analysis of
students- cyber bullying behaviour and simple regression analysis was
conducted in order to test whether each value in the scale could
explain cyber bullying behaviour.
Abstract: The objective of this research was to identify the
vegetation-soil relationships in Nodushan arid rangelands of Yazd. 5
sites were selected for measuring the cover of plant species and soil
attributes. Soil samples were taken in 0-10 and 10-80 cm layers. The
species studied were Salsola tomentosa, Salsola arbuscula, Peganum
harmala, Zygophylum eurypterum and Eurotia ceratoides. Canonical
correspondence analysis (CCA) was used to analyze the data. Based
on the CCA results, 74.9 % of vegetation-soil variation was explained
by axis 1-3. Axis 1, 2 and 3 accounted for 27.2%, 24.9 % and 22.8%
of variance respectively. Correlation between axis 1, 2, 3 and speciesedaphic
variables were 0.995, 0.989, 0.981 respectively. Soil texture,
lime, salinity and organic matter significantly influenced the
distribution of these plant species. Determination of soil-vegetation
relationships will be useful for managing and improving rangelands
in arid and semi arid environments.
Abstract: In this paper is described a new conception of the
Cartesian robot for automated assembly and also disassembly
process. The advantage of this conception is the utilization the
Cartesian assembly robot with its all peripheral automated devices for
assembly of the assembled product. The assembly product in the end
of the lifecycle can be disassembled with the same Cartesian
disassembly robot with the use of the same peripheral automated
devices and equipment. It is a new approach to problematic solving
and development of the automated assembly systems with respect to
lifecycle management of the assembly product and also assembly
system with Cartesian robot. It is also important to develop the
methodical process for design of automated assembly and
disassembly system with Cartesian robot. Assembly and disassembly
system use the same Cartesian robot input and output devices,
assembly and disassembly units in one workplace with different
application. Result of design methodology is the verification and
proposition of real automated assembly and disassembly workplace
with Cartesian robot for known verified model of assembled actuator.
Abstract: This study shows palynomorphological description of
pollen grains of Lamium garganicum, species of the family Labiatae.
Fresh material of this plant is taken in Mount Llogara, in Albania. By
comparison made between palinomorphological characteristics of
pollen grains of Lamium garganicum with those of Lamium
maculatum and Lamium purpureum, showed that granules have
similarities in the number of furrows. The pollen grains of Lamium
garganicum were larger in length and width than those of Lamium
maculatum and almost equal with those of Lamium purpureum.
Furrows are longer than those of pollen grains in Lamium maculatum
and shorter than those of Lamium purpureum. The layer of exine of
Lamium garganicum was thinner than that of two others. The
sculpture of exine was fine reticulate, where reticulas were uniform
whereas in Lamium purpureum was verrucate, with small verrucae; in
Lamium maculatum was reticulate.