Abstract: Chloride resistance in Ultra High Performance
Concrete (UHPC) is determined in this paper. This work deals with
the one dimension chloride transport, which can be potentially
dangerous particularly for the durability of concrete structures. Risk
of reinforcement corrosion due to exposure to the concrete surface to
direct the action of chloride ions (mainly in the form de-icing salts or
groundwater) is dangerously increases. The measured data are
investigated depending on the depth of penetration of chloride ions
into the concrete structure. Comparative measurements with normal
strength concrete are done as well. The experimental results showed
that UHCP have improved resistance of chlorides penetration than
NSC and also chloride diffusion depth is significantly lower in
UHCP.
Abstract: In this study, the evaluation of thermal stability of the
micrometer-sized silica particle reinforced epoxy composite was
carried out through the measurement of thermal expansion coefficient
and Young’s modulus of the specimens. For all the specimens in this
study from the baseline to those containing 50 wt% silica filler, the
thermal expansion coefficients and the Young’s moduli were
gradually decreased down to 20% and increased up to 41%,
respectively. The experimental results were compared with fillervolume-
based simple empirical relations. The experimental results of
thermal expansion coefficients correspond with those of Thomas’s
model which is modified from the rule of mixture. However, the
measured result for Young’s modulus tends to be increased slightly.
The differences in increments of the moduli between experimental and
numerical model data are quite large.
Abstract: The reduction of greenhouse gases emissions is highly
discussed ecological theme at present. In addition to power industry
also main production sectors of binders, i.e. cement, air and hydraulic
lime are very sensitive to these questions. One of the possibilities
how CO2 emissions can be reduced directly at clinker burnout is
represented by partial substitution of lime with a material containing
limy ions at absence of carbonate group. Fluidised fly ash is one of
such potential raw materials where CaO can be found free and also
bound in anhydrite, CaSO4. At application of FBC (fluidized bed
combustion) fly ash with approximate 20% CaO content and its
dosing ratio to high percent lime 1:2, corresponding stechiometrically
to the preparation of raw material powder, approximately 0,37 t CO2
per 1 ton of one-component cement would be released at clinker
burnout compared to 0,46 t CO2 when orthodox raw materials are
used. The reduction of CO2 emissions thus could reach even 20%.
Abstract: In this study, first thermoplastic composite materials
/plates that have high ballistic impact resistance were produced. For
this purpose, the thermoplastic prepreg and the vacuum bagging
technique were used to produce a composite material. Thermoplastic
prepregs (resin-impregnated fiber) that are supplied ready to be used,
namely high-density polyethylene (HDPE) was chosen as matrix and
unidirectional glass fiber was used as reinforcement. In order to
compare the fiber configuration effect on mechanical properties,
unidirectional and biaxial prepregs were used. Then the
microstructural properties of the composites were investigated with
scanning electron microscopy (SEM) analysis. Impact properties of
the composites were examined by Charpy impact test and tensile
mechanical tests and then the effects of ultraviolet irradiation were
investigated on mechanical performance.
Abstract: The lactic acid bacteria (LAB) were isolated from
10 samples of fermented foods (Sa-tor-dong and Bodo) in South
locality of Thailand. The 23 isolates of lactic acid bacteria were
selected, which were exhibited a clear zone and growth on MRS
agar supplemented with CaCO3. All of lactic acid bacteria were
tested on morphological and biochemical. The result showed that
all isolates were Gram’s positive, non-spore forming but only
10 isolates displayed catalase negative. The 10 isolates including
BD1 .1, BD 1.2, BD 2.1, BD2.2, BD 2.3, BD 3.1, BD 4.1, BD 5.2,
ST 4.1 and ST 5.2 were selected for inhibition activity
determination. Only 2 strains (ST 4.1 and BD 2.3) showed
inhibition zone on agar, when using Escherichia coli sp. as target
strain. The ST 4.1 showed highest inhibition zone on agar, which
was selected for probiotic property testing. The ST4.1 isolate
could grow in MRS broth containing a high concentration of
sodium chloride 6%, bile salts 7%, pH 4-10 and vary temperature
at 15-45°C.
Abstract: With demand for primary energy continuously
growing, search for renewable and efficient energy sources has been
high on agenda of our society. One of the most promising energy
sources is biogas technology. Residues coming from dairy industry
and milk processing could be used in biogas production; however,
low efficiency and high cost impede wide application of such
technology. One of the main problems is management and conversion
of organic residues through the anaerobic digestion process which is
characterized by acidic environment due to the low whey pH (
Abstract: Estimation of a proportion has many applications in
economics and social studies. A common application is the estimation
of the low income proportion, which gives the proportion of people
classified as poor into a population. In this paper, we present this
poverty indicator and propose to use the logistic regression estimator
for the problem of estimating the low income proportion. Various
sampling designs are presented. Assuming a real data set obtained
from the European Survey on Income and Living Conditions, Monte
Carlo simulation studies are carried out to analyze the empirical
performance of the logistic regression estimator under the various
sampling designs considered in this paper. Results derived from
Monte Carlo simulation studies indicate that the logistic regression
estimator can be more accurate than the customary estimator under
the various sampling designs considered in this paper. The stratified
sampling design can also provide more accurate results.
Abstract: This paper reports the empirical investigation on the
effect of involuntary displacement of indigenous tribes on their sociocultural
and food practices. A descriptive research design using the
quantitative approach was applied and individual of indigenous tribes
as unit of analysis. Through a self-administered survey among two
selected Malaysia indigenous tribes, one hundred fifty questionnaires
were successfully collected. With the application of descriptive and
inferential statistic some useful insights pertaining to the issue
investigated was significantly obtained. Findings revealed that
improvement on the socio-culture, economy and knowledge is
apparent on the indigenous groups’ resulted from displacement
program. Displacement also has a slight impact on indigenous
groups’ food practices. These positive indications provide significant
implications, not only for the indigenous groups themselves, but also
for the responsible authorities.
Abstract: A total of 150 meat type chickens comprising 50 each
of Arbor Acre, Marshall and Ross were used for this study which
lasted for 10 weeks at the Federal University of Agriculture,
Abeokuta, Nigeria. Growth performance data were collected from the
third week through week 10 and data obtained were analysed using
the Generalized Linear Model Procedure. Heritability estimates (h2)
for body dimensions carried out on the chicken strains ranged from
low to high. Marshall broiler chicken strain had the highest h2 for
body weight 0.46±0.04, followed by Arbor Acre and Ross with h2
being 0.38±0.12 and 0.26±0.06, respectively. The repeatability
estimates for body weight in the three broiler strains were high, and it
ranged from 0.70 at week 4 to 0.88 at week 10. Relationships
between the body weight and linear body measurements in the broiler
chicken strains were positive and highly significant (p > 0.05).
Abstract: In this paper, we have proposed a numerical method
for solving fuzzy Fredholm integral equation of the second kind. In
this method a combination of orthonormal Bernstein and Block-Pulse
functions are used. In most cases, the proposed method leads to
the exact solution. The advantages of this method are shown by an
example and calculate the error analysis.
Abstract: In this paper, we propose a multi-agent intelligent
system that is used for monitoring the health conditions of elderly
people. Monitoring the health condition of elderly people is a
complex problem that involves different medical units and requires
continuous monitoring. Such expert system is highly needed in rural
areas because of inadequate number of available specialized
physicians or nurses. Such monitoring must have autonomous
interactions between these medical units in order to be effective. A
multi-agent system is formed by a community of agents that
exchange information and proactively help one another to achieve the
goal of elderly monitoring. The agents in the developed system are
equipped with intelligent decision maker that arms them with the
rule-based reasoning capability that can assist the physicians in
making decisions regarding the medical condition of elderly people.
Abstract: Voltage sags are the most common power quality
disturbance in the distribution system. It occurs due to the fault in the
electrical network or by the starting of a large induction motor and
this can be solved by using the custom power devices such as
Dynamic Voltage Restorer (DVR). In this paper DVR is proposed to
compensate voltage sags on critical loads dynamically. The DVR
consists of VSC, injection transformers, passive filters and energy
storage (lead acid battery). By injecting an appropriate voltage, the
DVR restores a voltage waveform and ensures constant load voltage.
The simulation and experimental results of a DVR using MATLAB
software shows clearly the performance of the DVR in mitigating
voltage sags.
Abstract: Malathion (ML) is a well known pesticide commonly
used in many agricultural and non-agricultural processes. Its toxicity
has been attributed primarily to the accumulation of acetylcholine
(Ach) at nerve junctions, due to the inhibition of acetylcholinesterase
(AChE). The aim of the current research was to study the protective
effect of the melissa plant extract against reproductive impairment
induced by malathion in 32 male albino rats, and the biological
experiment was divided into four groups (8 in each) that given
malathion (27 mg/kg; 1/50 of the LD50 for an oral dose) and/or
Melissa officinalis (MO) extract (200mg/kg/day) by gavages
technique. The sperm counts, sperm motility, sperm morphology,
FSH, LH, and testosterone levels had been determined in testes
homogenate at the end of the experiment. It is worthy to report that,
rats treated with melissa extract did not show a significant difference
when compared with the control group, while rats given malathion
alone had significantly lower sperm count, sperm motility, and
significantly higher abnormal sperm numbers, than the untreated
control rats as well as having significantly lower serum FSH, LH, and
testosterone levels compared with the control group. Administrations
of melissa extract restore all mentioned histological parameters
towards the control group and the melissa extract had a strong
positive protective effect against malathion toxicity. Results the of
biological parameters were confirmed by the histological
examination of rat testes and indicated that, both control and melissa
groups showing normal seminiferous tubules, while malathion group
testicular tissues had necrosis, edema in the seminiferous tubules and
degeneration of spermatogonial cells lining the seminiferous tubules
with incomplete spermatogenesis. The use of melissa against
malathion improved the histological picture and showing normal
seminiferous tubules with complete spermatogenesis and almost there
was no histopathological changes could be noted.
Abstract: In development of floating photovoltaic generation
system, finding a suitable place of installation is as important as
development of economically feasible and stable structure. Especially
since floating photovoltaic system has its facility floating on water
surface, it is extremely important to review the effects of weather
conditions such as wind, water flow and floating matters, various
factors (such as fogs) that can reduce generation efficiency, possibility
of connection with power system, and legal restrictions. The method of
investigating suitable area and resource for development of
tracking-type floating photovoltaic generation system was proposed in
this paper, which can be used for development of floating and ocean
photovoltaic system in the future.
Abstract: This paper aims at finding a suitable neural network
for monitoring congestion level in electrical power systems. In this
paper, the input data has been framed properly to meet the target
objective through supervised learning mechanism by defining normal
and abnormal operating conditions for the system under study. The
congestion level, expressed as line congestion index (LCI), is
evaluated for each operating condition and is presented to the NN
along with the bus voltages to represent the input and target data.
Once, the training goes successful, the NN learns how to deal with a
set of newly presented data through validation and testing
mechanism. The crux of the results presented in this paper rests on
performance comparison of a multi-layered feed forward neural
network with eleven types of back propagation techniques so as to
evolve the best training criteria. The proposed methodology has been
tested on the standard IEEE-14 bus test system with the support of
MATLAB based NN toolbox. The results presented in this paper
signify that the Levenberg-Marquardt backpropagation algorithm
gives best training performance of all the eleven cases considered in
this paper, thus validating the proposed methodology.
Abstract: Anultra-low power capacitor less low-dropout voltage
regulator with improved transient response using gain enhanced feed
forward path compensation is presented in this paper. It is based on a
cascade of a voltage amplifier and a transconductor stage in the feed
forward path with regular error amplifier to form a composite gainenhanced
feed forward stage. It broadens the gain bandwidth and thus
improves the transient response without substantial increase in power
consumption. The proposed LDO, designed for a maximum output
current of 100 mA in UMC 180 nm, requires a quiescent current of
69 )A. An undershot of 153.79mV for a load current changes from
0mA to 100mA and an overshoot of 196.24mV for current change of
100mA to 0mA. The settling time is approximately 1.1 )s for the
output voltage undershooting case. The load regulation is of 2.77
)V/mA at load current of 100mA. Reference voltage is generated by
using an accurate band gap reference circuit of 0.8V.The costly
features of SOC such as total chip area and power consumption is
drastically reduced by the use of only a total compensation
capacitance of 6pF while consuming power consumption of 0.096
mW.
Abstract: Composite materials have important assets compared
to traditional materials. They bring many functional advantages:
lightness, mechanical resistance and chemical, etc. In the present
study we examine the effect of a circular central notch and a precrack
on the tensile fracture of two woven composite materials. The tensile
tests were applied to a standardized specimen, notched and a
precarcked (orientation of the crack 0°, 45° and 90°). These tensile
tests were elaborated according to an experimental planning design of
the type 23.31 requiring 24 experiments with three repetitions. By the
analysis of regression, we obtained a mathematical model describing
the maximum load according to the influential parameters (hole
diameter, precrack length, angle of a precrack orientation). The
specimens precracked at 90° have a better behavior than those having
a precrack at 45° and still better than those having of the precracks
oriented at 0°. In addition the maximum load is inversely
proportional to the notch size.
Abstract: The paper presents the results of clusterization by
Kohonen self-organizing maps (SOM) applied for analysis of array of
Raman spectra of multi-component solutions of inorganic salts, for
determination of types of salts present in the solution. It is
demonstrated that use of SOM is a promising method for solution of
clusterization and classification problems in spectroscopy of multicomponent
objects, as attributing a pattern to some cluster may be
used for recognition of component composition of the object.
Abstract: The paper describes the experiments and the kinetic
parameters calculus of the gasoil hydrofining. They are presented
experimental results of gasoil hidrofining using Mo and promoted
with Ni on aluminum support catalyst. The authors have adapted a
kinetic model gasoil hydrofining. Using this proposed kinetic model
and the experimental data they have calculated the parameters of the
model. The numerical calculus is based on minimizing the difference
between the experimental sulf concentration and kinetic model
estimation.
Abstract: The article is devoted to the problem of political
discourse and its reflection on mass cognition. This article is
dedicated to describe the myth as one of the main features of political
discourse. The dominance of an expressional and emotional
component in the myth is shown. Precedent phenomenon plays an
important role in distinguishing the myth from the linguistic point of
view. Precedent phenomena show the linguistic cognition, which is
characterized by their fame and recognition. Four types of myths
such as master myths, a foundation myth, sustaining myth,
eschatological myths are observed. The myths about the national idea
are characterized by national specificity. The main aim of the
political discourse with the help of myths is to influence on the mass
consciousness in order to motivate the addressee to certain actions so
that the target purpose is reached owing to unity of forces.