Abstract: There is not much effective guideline on development of design parameters selection on spring back for advanced high strength steel sheet metal in U-channel process during cold forming process. This paper presents the development of predictive model for spring back in U-channel process on advanced high strength steel sheet employing Response Surface Methodology (RSM). The experimental was performed on dual phase steel sheet, DP590 in Uchannel forming process while design of experiment (DoE) approach was used to investigates the effects of four factors namely blank holder force (BHF), clearance (C) and punch travel (Tp) and rolling direction (R) were used as input parameters using two level values by applying Full Factorial design (24 ). From a statistical analysis of variant (ANOVA), result showed that blank holder force (BHF), clearance (C) and punch travel (Tp) displayed significant effect on spring back of flange angle (β2 ) and wall opening angle (β1 ), while rolling direction (R) factor is insignificant. The significant parameters are optimized in order to reduce the spring back behavior using Central Composite Design (CCD) in RSM and the optimum parameters were determined. A regression model for spring back was developed. The effect of individual parameters and their response was also evaluated. The results obtained from optimum model are in agreement with the experimental values.
Abstract: In this study, we demonstrate the production of natural gas hydrates from permeable marine sediments with simultaneous mechanisms for methane recovery and methane-air or methane-air/carbon dioxide replacement. The simultaneous melting happens until the chemical potentials become equal in both phases as natural gas hydrate depletion continues and self-regulated methane-air replacement occurs over an arbitrary point. We observed certain point between dissociation and replacement mechanisms in the natural gas hydrate reservoir, and we call this boundary as critical methane concentration. By the way, when carbon dioxide was added, the process of chemical exchange of methane by air/carbon dioxide was observed in the natural gas hydrate. The suggested process will operate well for most global natural gas hydrate reservoirs, regardless of the operating conditions or geometrical constraints.
Abstract: Steady three-dimensional and two free surface waves
generated by moving bodies are presented, the flow problem to be
simulated is rich in complexity and poses many modeling challenges
because of the existence of breaking waves around the ship hull, and
because of the interaction of the two-phase flow with the turbulent
boundary layer. The results of several simulations are reported. The
first study was performed for NACA0012 of hydrofoil with different
meshes, this section is analyzed at h/c= 1, 0345 for 2D. In the second
simulation a mathematically defined Wigley hull form is used to
investigate the application of a commercial CFD code in prediction of
the total resistance and its components from tangential and normal
forces on the hull wetted surface. The computed resistance and wave
profiles are used to estimate the coefficient of the total resistance for
Wigley hull advancing in calm water under steady conditions. The
commercial CFD software FLUENT version 12 is used for the
computations in the present study. The calculated grid is established
using the code computer GAMBIT 2.3.26. The shear stress k-ωSST
model is used for turbulence modeling and the volume of fluid
technique is employed to simulate the free-surface motion. The
second order upwind scheme is used for discretizing the convection
terms in the momentum transport equations, the Modified HRIC
scheme for VOF discretization. The results obtained compare well
with the experimental data.
Abstract: In order to address construction project requirements
and specifications, scholars and practitioners need to establish
taxonomy according to a scheme that best fits their need. While
existing characterization methods are continuously being improved,
new ones are devised to cover project properties which have not been
previously addressed. One such method, the Project Definition Rating
Index (PDRI), has received limited consideration strictly as a
classification scheme. Developed by the Construction Industry
Institute (CII) in 1996, the PDRI has been refined over the last two
decades as a method for evaluating a project's scope definition
completeness during front-end planning (FEP). The main
contribution of this study is a review of practical project classification
methods, and a discussion of how PDRI can be used to classify
projects based on their readiness in the FEP phase. The proposed
model has been applied to 59 construction projects in Ontario, and
the results are discussed.
Abstract: Steady three-dimensional and two free surface waves
generated by moving bodies are presented, the flow problem to be
simulated is rich in complexity and poses many modeling challenges
because of the existence of breaking waves around the ship hull, and
because of the interaction of the two-phase flow with the turbulent
boundary layer. The results of several simulations are reported. The
first study was performed for NACA0012 of hydrofoil with different
meshes, this section is analyzed at h/c= 1, 0345 for 2D. In the second
simulation a mathematically defined Wigley hull form is used to
investigate the application of a commercial CFD code in prediction of
the total resistance and its components from tangential and normal
forces on the hull wetted surface. The computed resistance and wave
profiles are used to estimate the coefficient of the total resistance for
Wigley hull advancing in calm water under steady conditions. The
commercial CFD software FLUENT version 12 is used for the
computations in the present study. The calculated grid is established
using the code computer GAMBIT 2.3.26. The shear stress k-ωSST
model is used for turbulence modeling and the volume of fluid
technique is employed to simulate the free-surface motion. The
second order upwind scheme is used for discretizing the convection
terms in the momentum transport equations, the Modified HRIC
scheme for VOF discretization. The results obtained compare well
with the experimental data.
Abstract: The novel 3D SnO cabbages self-assembled by
nanosheets were successfully synthesized via template-free
hydrothermal growth method under facile conditions. The XRD
results manifest that the as-prepared SnO is tetragonal phase. The
TEM and HRTEM results show that the cabbage nanosheets are
polycrystalline structure consisted of considerable single-crystalline
nanoparticles. Two typical Raman modes A1g=210 and Eg=112 cm-1
of SnO are observed by Raman spectroscopy. Moreover, galvanostatic
cycling tests has been performed using the SnO cabbages as anode
material of lithium ion battery and the electrochemical results suggest
that the synthesized SnO cabbage structures are a promising anode
material for lithium ion batteries.
Abstract: The nanoindentation behaviour and phase
transformation of annealed single-crystal silicon wafers are examined.
The silicon specimens are annealed at temperatures of 250, 350 and
450ºC, respectively, for 15 minutes and are then indented to maximum
loads of 30, 50 and 70 mN. The phase changes induced in the indented
specimens are observed using transmission electron microscopy
(TEM) and micro-Raman scattering spectroscopy (RSS). For all
annealing temperatures, an elbow feature is observed in the unloading
curve following indentation to a maximum load of 30 mN. Under
higher loads of 50 mN and 70 mN, respectively, the elbow feature is
replaced by a pop-out event. The elbow feature reveals a complete
amorphous phase transformation within the indented zone, whereas
the pop-out event indicates the formation of Si XII and Si III phases.
The experimental results show that the formation of these crystalline
silicon phases increases with an increasing annealing temperature and
indentation load. The hardness and Young’s modulus both decrease as
the annealing temperature and indentation load are increased.
Abstract: The system for analyzing and eliciting public
grievances serves its main purpose to receive and process all sorts of
complaints from the public and respond to users. Due to the more
number of complaint data becomes big data which is difficult to store
and process. The proposed system uses HDFS to store the big data
and uses MapReduce to process the big data. The concept of cache
was applied in the system to provide immediate response and timely
action using big data analytics. Cache enabled big data increases the
response time of the system. The unstructured data provided by the
users are efficiently handled through map reduce algorithm. The
processing of complaints takes place in the order of the hierarchy of
the authority. The drawbacks of the traditional database system used
in the existing system are set forth by our system by using Cache
enabled Hadoop Distributed File System. MapReduce framework
codes have the possible to leak the sensitive data through
computation process. We propose a system that add noise to the
output of the reduce phase to avoid signaling the presence of
sensitive data. If the complaints are not processed in the ample time,
then automatically it is forwarded to the higher authority. Hence it
ensures assurance in processing. A copy of the filed complaint is sent
as a digitally signed PDF document to the user mail id which serves
as a proof. The system report serves to be an essential data while
making important decisions based on legislation.
Abstract: Among various active filters, shunt active filter is a
viable solution for reactive power and harmonics compensation. In
this paper, the SRF plan is used to generate current reference for
compensation and conventional PI controllers were used as the
controller to compensate the reactive power. The design of the closed
loop controllers is reserved simple by modeling them as first order
systems. Computationally uncomplicated and efficient SVM system
is used in the present work for better utilization of dc bus voltage.
The rating of shunt active filter has been finalized based on the
reactive power demand of the selected reactive load. The proposed
control and SVM technique are validated by simulating in MATLAB
software.
Abstract: In this paper, the dependence of soliton pulses with
respect to phase in a 10Gbps, single channel, dispersion
uncompensated telecommunication system was studied. The
characteristic feature of periodic soliton interaction was noted at the
Interaction point (I=6202.5Km) in one collision length of L=12405.1
Km. The interaction point is located for 10Gbps system with an
initial relative spacing (qo) of soliton as 5.28 using Perturbation
theory. It is shown that, when two in-phase solitons are launched,
they interact at the point I=6202.5 Km, but the interaction could be
restricted with introduction of different phase initially. When the
phase of the input solitons increases, the deviation of soliton pulses at
the ‘I’ also increases. We have successfully demonstrated this effect
in a telecommunication set-up in terms of Quality factor (Q), where
the Q=0 for in-phase soliton. The Q was noted to be 125.9, 38.63,
47.53, 59.60, 161.37, and 78.04 for different phases such as 10o, 20o,
30o, 45o, 60o and 90o degrees respectively at Interaction point (I).
Abstract: The 5th generation of mobile networks is term used in
various research papers and projects to identify the next major phase
of mobile telecommunications standards. 5G wireless networks will
support higher peak data rate, lower latency and provide best
connections with QoS guarantees.
In this article, we discuss various promising technologies for 5G
wireless communication systems, such as IPv6 support, World Wide
Wireless Web (WWWW), Dynamic Adhoc Wireless Networks
(DAWN), BEAM DIVISION MULTIPLE ACCESS (BDMA), Cloud
Computing, cognitive radio technology and FBMC/OQAM.
This paper is organized as follows: First, we will give introduction
to 5G systems, present some goals and requirements of 5G. In the
next, basic differences between 4G and 5G are given, after we talk
about key technology innovations of 5G systems and finally we will
conclude in last Section.
Abstract: We present a gas-liquid microfluidic system as a
reactor to obtain magnetite nanoparticles with an excellent degree of
control regarding their crystalline phase, shape and size. Several
types of microflow approaches were selected to prevent nanomaterial
aggregation and to promote homogenous size distribution. The
selected reactor consists of a mixer stage aided by ultrasound waves
and a reaction stage using a N2-liquid segmented flow to prevent
magnetite oxidation to non-magnetic phases. A milli-fluidic reactor
was developed to increase the production rate where a magnetite
throughput close to 450 mg/h in a continuous fashion was obtained.
Abstract: This study focuses on a novel method for dispersion
and distribution of reinforcement under high intensive shear stress to
produce metal composites. The polyacrylonitrile (PAN)-based short
carbon fiber (Csf) and Nextel 610 alumina fiber were dispersed under
high intensive shearing at mushy zone in semi-solid of A356 by a
novel method. The bundles and clusters were embedded by
infiltration of slurry into the clusters, thus leading to a uniform
microstructure. The fibers were embedded homogenously into the
aluminum around 576-580°C with around 46% of solid fraction.
Other experiments at 615°C and 568°C which are contained 0% and
90% solid respectively were not successful for dispersion and
infiltration of aluminum into bundles of Csf. The alumina fiber has
been cracked by high shearing load. The morphologies and
crystalline phase were evaluated by SEM and XRD. The adopted
thixo-process effectively improved the adherence and distribution of
Csf into Al that can be developed to produce various composites by
thixomixing.
Abstract: This paper describes an optimization tool-based
design strategy for a Current Mode Logic CML divide-by-2 circuit.
Representing a building block for output frequency generation in a
RFID protocol based-frequency synthesizer, the circuit was designed
to minimize the power consumption for driving of multiple loads
with unbalancing (at transceiver level). Implemented with XFAB
XC08 180 nm technology, the circuit was optimized through
MunEDA WiCkeD tool at Cadence Virtuoso Analog Design
Environment ADE.
Abstract: Software fault prediction models are created by using
the source code, processed metrics from the same or previous version
of code and related fault data. Some company do not store and keep
track of all artifacts which are required for software fault prediction.
To construct fault prediction model for such company, the training
data from the other projects can be one potential solution. Earlier we
predicted the fault the less cost it requires to correct. The training
data consists of metrics data and related fault data at function/module
level. This paper investigates fault predictions at early stage using the
cross-project data focusing on the design metrics. In this study,
empirical analysis is carried out to validate design metrics for cross
project fault prediction. The machine learning techniques used for
evaluation is Naïve Bayes. The design phase metrics of other projects
can be used as initial guideline for the projects where no previous
fault data is available. We analyze seven datasets from NASA
Metrics Data Program which offer design as well as code metrics.
Overall, the results of cross project is comparable to the within
company data learning.
Abstract: Intermetallic materials are among advanced
technology materials that have outstanding mechanical and physical
properties for high temperature applications. Especially creep
resistance, low density and high hardness properties stand out in such
intermetallics. The microstructure, mechanical properties of %88Ni-
%10Cr and %2Mn powders were investigated using specimens
produced by tube furnace sintering at 900-1300°C temperature. A
composite consisting of ternary additions, a metallic phase, Fe, Cr
and Mn have been prepared under Ar shroud and then tube furnace
sintered. XRD, SEM (Scanning Electron Microscope), were
investigated to characterize the properties of the specimens.
Experimental results carried out for composition %88Ni-%10Cr and
%2Mn at 1300°C suggest that the best properties as 138,80HV and
6,269/cm3 density were obtained at 1300°C.
Abstract: An important problem for the CaSO4/CaSO4･1/2H2O
Chemical heat pump (CHP) is that the material is deactivated through
repetitive reaction between hydration and dehydration in which the
crystal phase of the material is transformed from III-CaSO4 to
II-CaSO4. We investigated suppression on the phase change by adding
a sulfated compound. The most effective material was MgSO4. MgSO4
doping increased the durability of CaSO4 in the actual CHP repetitive
cycle of hydration/dehydration to 3.6 times that of undoped CaSO4.
The MgSO4-doped CaSO4 showed a higher phase transition
temperature and activation energy for crystal transformation from
III-CaSO4 to II-CaSO4. MgSO4 doping decreased the crystal lattice
size of CaSO4･1/2H2O and II-CaSO4 to smaller than that of undoped
CaSO4. Modification of the crystal structure is considered to be related
to the durability change in CaSO4 resulting from MgSO4 doping.
Abstract: Sol-enhanced Zn-Ni-Al2O3 nanocomposite coatings
were electroplated on mild steel by our newly developed solenhanced
electroplating method. In this method, transparent Al2O3 sol
was added into the acidic Zn-Ni bath to produced Zn-Ni-Al2O3nanocomposite
coatings. The chemical composition, microstructure and
mechanical properties of the composite and alloy coatings deposited
at two different agitation speed were investigated. The structure of all
coatings was single γ-Ni5Zn21 phase. The composite coatings possess
refined crystals with higher microhardness compared to Zn-Ni alloy
coatings. The wear resistance of Zn-Ni coatings was improved
significantly by incorporation of alumina nano particles into the
coatings. Higher agitation speed provided more uniform coatings
with smaller grain sized and slightly higher microhardness.
Considering composite coatings, high agitation speeds may facilitate
co-deposition of alumina in the coatings.
Abstract: This article presents two methods for the
compensation of harmonics generated by a nonlinear load. The first is
the classic method P-Q. The second is the controller by modern
method of artificial intelligence specifically fuzzy logic. Both
methods are applied to a shunt Active Power Filter (sAPF) based on a
three-phase voltage converter at five levels NPC topology. In
calculating the harmonic currents of reference, we use the algorithm
P-Q and pulse generation, we use the intersective PWM. For
flexibility and dynamics, we use fuzzy logic. The results give us clear
that the rate of Harmonic Distortion issued by fuzzy logic is better
than P-Q.
Abstract: Chitosan functionalized Fe3O4-Au core shell
nanoparticles have been prepared using a two-step wet chemical
approach using NaBH4 as reducing agent for formation of Au in
ethylene glycol. X-ray diffraction studies shows individual phases of
Fe3O4 and Au in the as prepared samples with crystallite size of 5.9
and 11.4 nm respectively. The functionalization of the core-shell
nanostructure with Chitosan has been confirmed using Fourier
transform infrared spectroscopy along with signatures of octahedral
and tetrahedral sites of Fe3O4 below 600cm-1. Mössbauer
spectroscopy shows decrease in particle-particle interaction in
presence of Au shell (72% sextet) than pure oleic coated Fe3O4
nanoparticles (88% sextet) at room temperature. At 80K, oleic acid
coated Fe3O4 shows only sextets whereas the Chitosan functionalized
Fe3O4 and Chitosan functionalized Fe3O4@Au core shell show
presence of 5 and 11% doublet, respectively.