Abstract: As we make progressive products for good works, and
future industries want to get higher speed and resolution from various
developments in the robotics as well as precise control system, the
concept of control feedback is getting more important. Within a range
of industrial developments, the concept is most responsible for the
high reliability of a device. We explain an efficient analyzing method
of a rotary encoder such as an incremental type encoder and absolute
type encoder using the LabVIEW program
Abstract: Under the difficult access to finance of SMEs, they expect that its relationship with the banks shall constitute a real help to access appropriate financing, at reasonable costs and requirements, given the possibility of mutually beneficial and long lasting relation. The literature, but also the research we have carried on, is centered on such determinants as concentration and the length of the relationship, but at the same time, there is little certainty that banks are responding positively to them. Furthermore, although the trust is considered as being a fundamental element of bank relationship – see the case house bank – SMEs find that the banks finance them looking rather on collaterals and covenants than to trust. Moreover, a positive behavior, such as prompt or advance repayments of loans, doesn-t generate any positive feedback from the banks side. All these show a deep un-satisfaction of the SMEs concerning their relationship banking.
Abstract: Atherosclerosis is the condition in which an artery
wall thickens as the result of a build-up of fatty materials such as
cholesterol. It is a syndrome affecting arterial blood vessels, a
chronic inflammatory response in the walls of arteries, in large part
due to the accumulation of macrophage white blood cells and
promoted by low density (especially small particle) lipoproteins
(plasma proteins that carry cholesterol and triglycerides) without
adequate removal of fats and cholesterol from the macrophages by
functional high density lipoproteins (HDL). It is commonly referred
to as a hardening or furring of the arteries. It is caused by the
formation of multiple plaques within the arteries.
Abstract: The low power wireless sensor devices which usually
uses the low power wireless private area network (IEEE 802.15.4)
standard are being widely deployed for various purposes and in
different scenarios. IPv6 low power wireless private area network
(6LoWPAN) was adopted as part of the IETF standard for the
wireless sensor devices so that it will become an open standard
compares to other dominated proprietary standards available in the
market. 6LoWPAN also allows the integration and communication of
sensor nodes with the Internet more viable. This paper presents a
comparative study on different available IPv6 platforms for wireless
sensor networks including open and close sources. It also discusses
about the platforms used by these stacks. Finally it evaluates and
provides appropriate suggestions which can be use for selection of
required IPv6 stack for low power devices.
Abstract: In accordance with environmental impacts contended in Kyoto Protocol, the study aims to explore the different administrative and non-administrative measurements that industrial countries, such as America, German, Japan, Korea, Holland and British take to face with the increasing Global Warming phenomena. By large, these measurements consist of versatile dimensions, including of education and advocating, economical instruments, research developments and instances, restricted instruments, voluntary contacts, exchangeable permit for carbon-release and public investments. The results of discussion for the study are as follows: both economical impacts as well as reformations for nations that are affected via Kyoto Protocol, and human testifying for variables of global surroundings in the age of Kyoto Protocol.
Abstract: Anxiety is a common disorder that attacks many people in society and often accompanied by physiological sensations such as tachycardia, chest pain, shortness of breath, insensitivity and etc. The purpose of this study is to characterize the putative anxiolytic-like effects of DEV (dichloromethane extracts of valerian) using the elevated plus maze (EPM) in rats. DEV was dissolved in DMSO and orally administered at different doses to adult male wistar rats, 0.5, 1.5 and 3 hours before behavioral evaluation in an EPM respectively. Control rats were treated with an equal volume of DMSO. Single treatment of DEV (at 0.1,0.2. 0.3, and 0.4 g/kg) significantly increased time-spent and arm entries into open arms of EPM versus control groups (p
Abstract: The study aimed to identify the logical structure of
data and particularities of developing and testing a website designed
for selling farm products through online auctions.
The research is based on a short literature review in the field and
exploratory trials of some successful models from other industries, in
order to identify the advantages of using such tool, as well as the
optimal structure and functionality of an auction portal. In the last
part, the study focuses on the results of testing the website by the
potential beneficiaries.
Conclusions of the study underlines that the particularities of some
agricultural products could raise difficulties in the process of selling
them through online auctions, but the use of such system it is
perceived to bring significant improvements in the supply chain.
The results of scientific investigations require a more detailed
study regarding the importance of using quality standards for
agricultural products sold via online auction, the impact that
implementation of an online payment system could have on trade
with agricultural products and problems which could arise in using
the website in different countries.
Abstract: Aims for this study: first, to compare the expertise
level in data analysis, communication and information technologies
in undergraduate psychology students. Second, to verify the factor
structure of E-ETICA (Escala de Experticia en Tecnologias de la Informacion, la Comunicacion y el Análisis or Data Analysis,
Communication and Information'Expertise Scale) which had shown
an excellent internal consistency (α= 0.92) as well as a simple factor
structure. Three factors, Complex, Basic Information and
Communications Technologies and E-Searching and Download
Abilities, explains 63% of variance. In the present study, 260
students (119 juniors and 141 seniors) were asked to respond to
ETICA (16 items Likert scale of five points 1: null domain to 5: total
domain). The results show that both junior and senior students report
having very similar expertise level; however, E-ETICA presents a
different factor structure for juniors and four factors explained also
63% of variance: Information E-Searching, Download and Process;
Data analysis; Organization; and Communication technologies.
Abstract: The effect of plant growth-promoting rhizobacteria
(PGPR) on seed germination, seedling growth and yield of field
grown maize were evaluated in three experiments. In these
experiments six bacterial strains include P.putida strain R-168,
P.fluorescens strain R-93, P.fluorescens DSM 50090, P.putida
DSM291, A.lipoferum DSM 1691, A.brasilense DSM 1690 were
used. Results of first study showed seed Inoculation significantly
enhanced seed germination and seedling vigour of maize. In second
experiment, leaf and shoot dry weight and also leaf surface area
significantly were increased by bacterial inoculation in both sterile
and non-sterile soil. The results showed that inoculation with
bacterial treatments had a more stimulating effect on growth and
development of plants in nonsterile than sterile soil. In the third
experiment, Inoculation of maize seeds with all bacterial strains
significantly increased plant height, 100 seed weight, number of seed
per ear and leaf area .The results also showed significant increase in
ear and shoot dry weight of maize.
Abstract: This study was conducted using the data collected at the mouth of Jen-Gen River to investigate and analyze chromium (Cr) contained in the sediments, and to evaluate the accumulation of Cr and the degree of its potential risk. The results show that samples collected at all monitoring stations near the mouth of Jen-Gen River contain 92–567 mg/kg of Cr with average of 366±166 mg/kg. The spatial distribution of Cr reveals that the Cr concentration is relatively high in the river mouth region, and gradually diminishes toward the harbor region. This indicates that upstream industrial and municipal wastewater discharges along the river bank are major sources of pollution. The accumulation factor and potential ecological risk index indicate that the sedimentation at Jen-Gen River mouth has the most serious degree of Cr accumulation and the highest ecological potential risk.
Abstract: In the framework of the image compression by
Wavelet Transforms, we propose a perceptual method by
incorporating Human Visual System (HVS) characteristics in the
quantization stage. Indeed, human eyes haven-t an equal sensitivity
across the frequency bandwidth. Therefore, the clarity of the
reconstructed images can be improved by weighting the quantization
according to the Contrast Sensitivity Function (CSF). The visual
artifact at low bit rate is minimized. To evaluate our method, we use
the Peak Signal to Noise Ratio (PSNR) and a new evaluating criteria
witch takes into account visual criteria. The experimental results
illustrate that our technique shows improvement on image quality at
the same compression ratio.
Abstract: Unmanned aerial vehicles (UAVs) performing their
operations for a long time have been attracting much attention in
military and civil aviation industries for the past decade. The
applicable field of UAV is changing from the military purpose only to
the civil one. Because of their low operation cost, high reliability and
the necessity of various application areas, numerous development
programs have been initiated around the world. To obtain the optimal
solutions of the design variable (i.e., sectional airfoil profile, wing
taper ratio and sweep) for high performance of UAVs, both the lift and
lift-to-drag ratio are maximized whereas the pitching moment should
be minimized, simultaneously. It is found that the lift force and
lift-to-drag ratio are linearly dependent and a unique and dominant
solution are existed. However, a trade-off phenomenon is observed
between the lift-to-drag ratio and pitching moment. As the result of
optimization, sixty-five (65) non-dominated Pareto individuals at the
cutting edge of design spaces that are decided by airfoil shapes can be
obtained.
Abstract: Information and Communications Technologies (ICT) has been integrated in education in many developing and developed countries alike, but the use of ICT in Tanzanian schools is dismal. Many Tanzanian secondary schools have no computers. The few schools with computers use them primarily for secretarial services and computer literacy training. The Tanzanian education system at other levels like secondary school level has to undergo substantial transformation, underscored by the growing application of new information and communication technology. This paper presents the e-readiness survey result from secondary schools in Tanzania. The paper also suggests how Tanzania can make use of the few present ICT resources to support and improve teaching and learning functions to improve performance and acquisition of knowledge by using e-Learning Management System (e-LMS).
Abstract: to simulate the phenomenon of electronic transport in semiconductors, we try to adapt a numerical method, often and most frequently it’s that of Monte Carlo. In our work, we applied this method in the case of a ternary alloy semiconductor GaInP in its cubic form; The Calculations are made using a non-parabolic effective-mass energy band model. We consider a band of conduction to three valleys (ΓLX), major of the scattering mechanisms are taken into account in this modeling, as the interactions with the acoustic phonons (elastic collisions) and optics (inelastic collisions). The polar optical phonons cause anisotropic collisions, intra-valleys, very probable in the III-V semiconductors. Other optical phonons, no polar, allow transitions inter-valleys. Initially, we present the full results obtained by the simulation of Monte Carlo in GaInP in stationary regime. We consider thereafter the effects related to the application of an electric field varying according to time, we thus study the transient phenomenon which make their appearance in ternary material
Abstract: Higher capacities of power plants together with
increased awareness on environmental considerations have led to
taller height of stacks. It is seen that strong wind can result in falling
of stacks. So, aerodynamic consideration of stacks is very important
in order to save the falling of stacks. One stack is not enough in
industries and power sectors and two or three stacks are required for
proper operation of the unit. It is very important to arrange the stacks
in proper way to resist their downfall. The present experimental
study concentrates on the mutual effect of three nearby stacks on
each other at three different arrangements, viz. linear, side-by-side
and triangular. The experiments find out the directions of resultant
forces acting on the stacks in different configurations so that proper
arrangement of supports can be made with respect to the wind
directionality obtained from local meteorological data. One can also
easily ascertain which stack is more vulnerable to wind in
comparison to the others for a particular configuration. Thus, this
study is important in studying the effect of wind force on three stacks
in different arrangements and is very helpful in placing the supports
in proper places in order to avoid failing of stack-like structures due
to wind.
Abstract: The aim of this paper is to confirm the effect of key
design parameters, the punch radius and punch angle, on rupture of the
expansion tube using a finite element analysis with a ductile damage
model. The results of the finite element analysis indicated that the
expansion ratio of the tube was mainly affected by the radius of the
punch. However, the rupture was more affected by the punch angle
than the radius of the punch. The existence of a specific punch angle,
at which rupture did not occur, even if the radius of the punch was
increased, was found.
Abstract: This paper presents a novel approach for the design of
microwave circuits using Adaptive Network Fuzzy Inference
Optimizer (ANFIO). The method takes advantage of direct synthesis
of subsections of the amplifier using very fast and accurate ANFIO
models based on exact simulations using ADS. A mapping from
course space to fine space known as space mapping is also used. The
proposed synthesis approach takes into account the noise and
scattering parameters due to parasitic elements to achieve optimal
results. The overall ANFIO system is capable of designing different
LNAs at different noise and scattering criteria. This approach offers
significantly reduced time in the design of microwave amplifiers
within the validity range of the ANFIO system. The method has been
proven to work efficiently for a 2.4GHz LNA example. The S21 of
10.1 dB and noise figure (NF) of 2.7 dB achieved for ANFIO while
S21 of 9.05 dB and NF of 2.6 dB achieved for ANN.
Abstract: In our modern society electricity is vital to our health,
safety, comfort and well-being. While our daily use of electricity is
often taken for granted, public concern has arisen about potential
adverse health effects from electric and magnetic – electromagnetic –
fields (EMFs) produced by our use of electricity.
This paper aims to compare between the measured magnetic field
values and the simulated models for the indoor medium to low
voltage (MV/LV) distribution substations.
To calculate the magnetic flux density in the substations,
interactive software SUBCALC is used which is based on closed
form solution of the Biot-Savart law with 3D conductor model.
The comparison between the measured values and the simulated
models was acceptable. However there were some discrepancies, as
expected, may be due to the current variation during measurements.
Abstract: The use of synthetic retardants in polymeric insulated
cables is not uncommon in the high voltage engineering to study
electrical treeing phenomenon. However few studies on organic
materials for the same investigation have been carried. .This paper
describes the study on the effects of Oil Palm Empty Fruit Bunch
(OPEFB) microfiller on the tree initiation and propagation in silicone
rubber with different weight percentages (wt %) of filler to insulation
bulk material. The weight percentages used were 0 wt % and 1 wt %
respectively. It was found that the OPEFB retards the propagation of
the electrical treeing development. For tree inception study, the
addition of 1(wt %) OPEFB has increase the tree inception voltage of
silicone rubber. So, OPEFB is a potential retardant to the initiation
and growth of electrical treeing occurring in polymeric materials for
high voltage application. However more studies on the effects of
physical and electrical properties of OPEFB as a tree retardant
material are required.
Abstract: Circular knitting machine makes the fabric with more than two knitting tools. Variation of yarn tension between different knitting tools causes different loop length of stitches duration knitting process. In this research, a new intelligent method is applied to control loop length of stitches in various tools based on ideal shape of stitches and real angle of stitches direction while different loop length of stitches causes stitches deformation and deviation those of angle. To measure deviation of stitch direction against variation of tensions, image processing technique was applied to pictures of different fabrics with constant front light. After that, the rate of deformation is translated to needed compensation of loop length cam degree to cure stitches deformation. A fuzzy control algorithm was applied to loop length modification in knitting tools. The presented method was experienced for different knitted fabrics of various structures and yarns. The results show that presented method is useable for control of loop length variation between different knitting tools based on stitch deformation for various knitted fabrics with different fabric structures, densities and yarn types.