Abstract: This paper presents design trade-off and performance impacts of
the amount of pipeline phase of control path signals in a wormhole-switched
network-on-chip (NoC). The numbers of the pipeline phase of the control
path vary between two- and one-cycle pipeline phase. The control paths
consist of the routing request paths for output selection and the arbitration
paths for input selection. Data communications between on-chip routers are
implemented synchronously and for quality of service, the inter-router data
transports are controlled by using a link-level congestion control to avoid
lose of data because of an overflow. The trade-off between the area (logic
cell area) and the performance (bandwidth gain) of two proposed NoC router
microarchitectures are presented in this paper. The performance evaluation is
made by using a traffic scenario with different number of workloads under
2D mesh NoC topology using a static routing algorithm. By using a 130-nm
CMOS standard-cell technology, our NoC routers can be clocked at 1 GHz,
resulting in a high speed network link and high router bandwidth capacity
of about 320 Gbit/s. Based on our experiments, the amount of control path
pipeline stages gives more significant impact on the NoC performance than
the impact on the logic area of the NoC router.
Abstract: This paper focuses on the Mega-Sub Controlled
Structure Systems (MSCSS) performances and characteristics
regarding the new control principle contained in MSCSS subjected to
strong earthquake excitations. The adopted control scheme consists of
modulated sub-structures where the control action is achieved by
viscous dampers and sub-structure own configuration. The
elastic-plastic time history analysis under severe earthquake excitation
is analyzed base on the Finite Element Analysis Method (FEAM), and
some comparison results are also given in this paper. The result shows
that the MSCSS systems can remarkably reduce vibrations effects
more than the mega-sub structure (MSS). The study illustrates that the
improved MSCSS presents good seismic resistance ability even at 1.2g
and can absorb seismic energy in the structure, thus imply that
structural members cross section can be reduce and achieve to good
economic characteristics. Furthermore, the elasto-plastic analysis
demonstrates that the MSCSS is accurate enough regarding
international building evaluation and design codes. This paper also
shows that the elasto-plastic dynamic analysis method is a reasonable
and reliable analysis method for structures subjected to strong
earthquake excitations and that the computed results are more precise.
Abstract: In diversity rich environments, such as in Ultra-
Wideband (UWB) applications, the a priori determination of the
number of strong diversity branches is difficult, because of the considerably large number of diversity paths, which are characterized
by a variety of power delay profiles (PDPs). Several
Rake implementations have been proposed in the past, in order to reduce the number of the estimated and combined paths. To this
aim, we introduce two adaptive Rake receivers, which combine
a subset of the resolvable paths considering simultaneously the
quality of both the total combining output signal-to-noise ratio (SNR) and the individual SNR of each path. These schemes achieve
better adaptation to channel conditions compared to other known receivers, without further increasing the complexity. Their performance
is evaluated in different practical UWB channels, whose models are based on extensive propagation measurements. The
proposed receivers compromise between the power consumption,
complexity and performance gain for the additional paths, resulting in important savings in power and computational resources.
Abstract: Traffic congestion has become a major problem in
many countries. One of the main causes of traffic congestion is due
to road merges. Vehicles tend to move slower when they reach the
merging point. In this paper, an enhanced algorithm for traffic
simulation based on the fluid-dynamic algorithm and kinematic wave
theory is proposed. The enhanced algorithm is used to study traffic
congestion at a road merge. This paper also describes the
development of a dynamic traffic simulation tool which is used as a
scenario planning and to forecast traffic congestion level in a certain
time based on defined parameter values. The tool incorporates the
enhanced algorithm as well as the two original algorithms. Output
from the three above mentioned algorithms are measured in terms of
traffic queue length, travel time and the total number of vehicles
passing through the merging point. This paper also suggests an
efficient way of reducing traffic congestion at a road merge by
analyzing the traffic queue length and travel time.
Abstract: This study presents the improvement of thermal
performance of heat pipe using copper nanofluid with aqueous
solution of n-Butanol. The nanofluids kept in the suspension of
conventional fluids have the potential of superior heat transfer
capability than the conventional fluids due to their improved thermal
conductivity. In this work, the copper nanofluid which has a 40 nm
size with a concentration of 100 mg/lit is kept in the suspension of
the de-ionized (DI) water and an aqueous solution of n-Butanol and
these fluids are used as a working medium in the heat pipe. The study
discusses about the effect of heat pipe inclination, type of working
fluid and heat input on the thermal efficiency and thermal resistance.
The experimental results are evaluated in terms of its performance
metrics and are compared with that of DI water.
Abstract: This study was designed to formulate,
pharmaceutically evaluate a topical skin-care cream (w/o emulsion)
of Aloe Vera versus its vehicle (Base) as control and determine their
effects on Stratum Corneum (SC) water content and Transepidermal
water loss (TEWL). Base containing no extract and a Formulation
containing 3% concentrated extract of Aloe Vera was developed by
entrapping in the inner aqueous phase of w/o emulsion (cream).
Lemon oil was incorporated to improve the odor. Both the Base and
Formulation were stored at 8°C ±0.1°C (in refrigerator), 25°C±0.1°C,
40°C±0.1°C and 40°C± 0.1°C with 75% RH (in incubator) for a
period of 4 weeks to predict their stability. The evaluation parameters
consisted of color, smell, type of emulsion, phase separation,
electrical conductivity, centrifugation, liquefaction and pH. Both the
Base and Formulation were applied to the cheeks of 21 healthy
human volunteers for a period of 8 weeks Stratum corneum (SC)
water content and Transepidermal water loss (TEWL) were
monitored every week to measure any effect produced by these
topical creams. The expected organoleptic stability of creams was
achieved from 4 weeks in-vitro study period. Odor was disappeared
with the passage of time due to volatilization of lemon oil. Both the
Base and Formulation produced significant (p≤0.05) changes in
TEWL with respect to time. SC water content was significantly
(p≤0.05) increased by the Formulation while the Base has
insignificant (p 0.05) effects on SC water content. The newly
formulated cream of Aloe Vera, applied is suitable for improvement
and quantitative monitoring of skin hydration level (SC water
content/ moisturizing effects) and reducing TEWL in people with dry
skin.
Abstract: Six parameters, the effective diffusivity (De),
activation energy of De, pre-exponential factor of De, amount
(ASOW) of self-organized water species, and amplitude (α) of the
forced oscillation of the molecular mobility (1/tC) derived from the
forced cyclic temperature change operation, were characterized by
using six typical foods, squid, sardines, scallops, salmon, beef, and
pork, as a function of the correlation time (tC) of the water molecule-s
proton retained in the foods. Each of the six parameters was clearly
divided into the water species A1 and A2 at a specified value of tC
=10-8s (=CtC), indicating an anomalous change in the physicochemical
nature of the water species at the CtC. The forced oscillation of 1/tC
clearly demonstrated a characteristic mode depending on the food
shown as a three dimensional map associated with 1/tC, the amount of
self-organized water, and tC.
Abstract: The environment pollution with pesticides and heavy
metals is a recognized problem nowadays, with extension to the
global scale the tendency of amplification. Even with all the progress
in the environmental field, both in the emphasize of the effect of the
pollutants upon health, the linked studies environment-health are
insufficient, not only in Romania but all over the world also. We aim
to describe the particular situation in Romania regarding the
uncontrolled use of pesticides, to identify and evaluate the risk zones
for health and the environment in Romania, with the final goal of
designing adequate programs for reduction and control of the risk
sources. An exploratory study was conducted to determine the
magnitude of the pesticide use problem in a population living in
Saliste, a rural setting in Transylvania, Romania. The significant
stakeholders in Saliste region were interviewed and a sample from
the population living in Saliste area was selected to fill in a designed
questionnaire. All the selected participants declared that they used
pesticides in their activities for more than one purpose. They
declared they annually applied pesticides for a period of time
between 11 and 30 years, from 5 to 9 days per year on average,
mainly on crops situated at some distance from the houses but high
risk behavior was identified as the volunteers declared the use of
pesticides in the backyard gardens, near their homes, where children
were playing. The pesticide applicators did not have the necessary
knowledge about safety and exposure. The health data must be
correlated with exposure biomarkers in attempt to identify the
possible health effects of the pesticides exposure. Future plans
include educational campaigns to raise the awareness of the
population on the danger of uncontrolled use of pesticides.
Abstract: For Romania, the fulfilment of the obligations
undertaken as a member state of the European Union in accordance
with the Treaty of Accession requires the effective implementation of
sustainable development principles and practices, this being the only
reasonable development option, which adequately draws in on the
economic, social and environment resources. Achieving this
objective is based on a profound analysis of the realities in the
Romanian economy, which will reflect the existent situation and the
action directions for the future. The paper presents an analysis of the
Romanian economic performances compared to the EU economy,
based on the sustainable value (SV) model. The analysis highlighted
the considerable gap between Romania and the EU regarding the
sustainable capitalization of resources, the provided information
being useful to justify strategic development decisions at a micro and
macro levels.
Abstract: In this work, we propose a hybrid heuristic in order to
solve the Team Orienteering Problem (TOP). Given a set of points (or
customers), each with associated score (profit or benefit), and a team
that has a fixed number of members, the problem to solve is to visit a
subset of points in order to maximize the total collected score. Each
member performs a tour starting at the start point, visiting distinct
customers and the tour terminates at the arrival point. In addition,
each point is visited at most once, and the total time in each tour
cannot be greater than a given value. The proposed heuristic combines
beam search and a local optimization strategy. The algorithm was
tested on several sets of instances and encouraging results were
obtained.
Abstract: The 20th century has brought much development to the practice of Architecture worldwide, and technology has bridged inhabitation limits in many regions of the world with high levels of comfort and conveniences, most times at high costs to the environment. Throughout the globe, the tropical countries are being urbanized at an unprecedented rate and housing has become a major issue worldwide, in light of increased demand and lack of appropriate infra-structure and planning. Buildings and urban spaces designed in tropical cities have mainly adopted external concepts that in most cases do not fit the needs of the inhabitants living in such harsh climatic environment, and when they do, do so at high financial, environmental and cultural costs. Traditional architectural practices can provide valuable understanding on how self-reliance and autonomy of construction can be reinforced in rural-urban tropical environments. From traditional housing knowledge, it is possible to derive lessons for the development of new construction materials that are affordable, environmentally friendly, culturally acceptable and accesible to all.Specifically to the urban context, such solutions are of outmost importance, given the needs to a more democratic society, where access to housing is considered high in the agenda for development. Traditional or rural constructions are also ongoing through extensive changes eventhough they have mostly adopted climate-responsive building practices relying on local resources (with minimum embodied energy) and energy (for comfort and quality of life). It is important to note that many of these buildings can actually be called zero-energy, and hold potential answers to enable transition from high energy, high cost, low comfort urban habitations to zero/low energy habitations with high quality urban livelihood. Increasing access to modern urban lifestyels have also an effect on the aspirations from people in terms of performance, comfort and convenience in terms of their housing and the way it is produced and used. These aspirations are resulting in transitions from localresource dependent habitations- to non-local resource based highenergy urban style habitations. And such transitions are resulting in the habitations becoming increasingly unsuited to the local climatic conditions with increasing discomfort, ill-health, and increased CO2 emissions and local environmental disruption. This research studies one specific transition group in the context of 'water communities' in tropical-equatorial regions: Ribeirinhos housing typology (Amazonas, Brazil). The paper presents the results of a qualitative sustainability assessment of the housing typologies under transition, found at the Ribeirinhos communities.
Abstract: The calculation of buckling length factor (K) for steel
frames columns is a major and governing processes to determine the
dimensions steel frame columns cross sections during design. The
buckling length of steel frames columns has a direct effect on the cost
(weight) of using cross section. A new formula is required to
determine buckling length factor (K) by simplified way. In this
research a new formula for buckling length factor (K) was established
to determine by accurate method for a limited interval of columns
ends rigidity (GA, GB). The new formula can be used ease to
evaluate the buckling length factor without needing to complicated
equations or difficult charts.
Abstract: In this study concept of experimental design is
successfully applied for the determination of optimum condition to
produce PP/SWCNT (Polypropylene/Single wall carbon nanotube)
nanocomposite. Central composite design as one of experimental
design techniques is employed for the optimization and statistical
determination of the significant factors influencing on the tensile
modulus and yield stress as mechanical properties of this
nanocomposite. The significant factors are SWCNT weight fraction
and acid treatment time for functionalizing the nanoparticles.
Optimum conditions are in 0.7 % of SWCNT weight fraction and 210
min as acid treatment time for 1112.75 ± 28 MPa as maximum tensile
modulus and in 216 min and 0.65 % as acid treatment time and
SWCNT weight fraction respectively for 40.26 ± 0.3 MPa as
maximum yield stress. Also after setting new experiments for test
these optimum conditions, found excelent agreement with predicted
values.
Abstract: To evaluate genetic variation of wheat (Triticum aestivum) affected by heat and drought stress on eight Australian wheat genotypes that are parents of Doubled Haploid (HD) mapping populations at the vegetative stage, the water stress experiment was conducted at 65% field capacity in growth room. Heat stress experiment was conducted in the research field under irrigation over summer. Result show that water stress decreased dry shoot weight and RWC but increased osmolarity and means of Fv/Fm values in all varieties except for Krichauff. Krichauff and Kukri had the maximum RWC under drought stress. Trident variety was shown maximum WUE, osmolarity (610 mM/Kg), dry mater, quantum yield and Fv/Fm 0.815 under water stress condition. However, the recovery of quantum yield was apparent between 4 to 7 days after stress in all varieties. Nevertheless, increase in water stress after that lead to strong decrease in quantum yield. There was a genetic variation for leaf pigments content among varieties under heat stress. Heat stress decreased significantly the total chlorophyll content that measured by SPAD. Krichauff had maximum value of Anthocyanin content (2.978 A/g FW), chlorophyll a+b (2.001 mg/g FW) and chlorophyll a (1.502 mg/g FW). Maximum value of chlorophyll b (0.515 mg/g FW) and Carotenoids (0.234 mg/g FW) content belonged to Kukri. The quantum yield of all varieties decreased significantly, when the weather temperature increased from 28 ÔùªC to 36 ÔùªC during the 6 days. However, the recovery of quantum yield was apparent after 8th day in all varieties. The maximum decrease and recovery in quantum yield was observed in Krichauff. Drought and heat tolerant and moderately tolerant wheat genotypes were included Trident, Krichauff, Kukri and RAC875. Molineux, Berkut and Excalibur were clustered into most sensitive and moderately sensitive genotypes. Finally, the results show that there was a significantly genetic variation among the eight varieties that were studied under heat and water stress.
Abstract: This paper presents a systematic approach for the
design of power system stabilizer using genetic algorithm and
investigates the robustness of the GA based PSS. The proposed
approach employs GA search for optimal setting of PSS parameters.
The performance of the proposed GPSS under small and large
disturbances, loading conditions and system parameters is tested.
The eigenvalue analysis and nonlinear simulation results show the
effectiveness of the GPSS to damp out the system oscillations. It is
found tat the dynamic performance with the GPSS shows improved
results, over conventionally tuned PSS over a wide range of
operating conditions.
Abstract: In this paper a new embedded Singly Diagonally
Implicit Runge-Kutta Nystrom fourth order in fifth order method for
solving special second order initial value problems is derived. A
standard set of test problems are tested upon and comparisons on the
numerical results are made when the same set of test problems are
reduced to first order systems and solved using the existing
embedded diagonally implicit Runge-Kutta method. The results
suggests the superiority of the new method.
Abstract: Nanostructured materials have attracted many
researchers due to their outstanding mechanical and physical
properties. For example, carbon nanotubes (CNTs) or carbon
nanofibres (CNFs) are considered to be attractive reinforcement
materials for light weight and high strength metal matrix composites.
These composites are being projected for use in structural
applications for their high specific strength as well as functional
materials for their exciting thermal and electrical characteristics. The
critical issues of CNT-reinforced MMCs include processing
techniques, nanotube dispersion, interface, strengthening mechanisms
and mechanical properties. One of the major obstacles to the effective
use of carbon nanotubes as reinforcements in metal matrix
composites is their agglomeration and poor distribution/dispersion
within the metallic matrix. In order to tap into the advantages of the
properties of CNTs (or CNFs) in composites, the high dispersion of
CNTs (or CNFs) and strong interfacial bonding are the key issues
which are still challenging. Processing techniques used for synthesis
of the composites have been studied with an objective to achieve
homogeneous distribution of carbon nanotubes in the matrix.
Modified mechanical alloying (ball milling) techniques have emerged
as promising routes for the fabrication of carbon nanotube (CNT)
reinforced metal matrix composites. In order to obtain a
homogeneous product, good control of the milling process, in
particular control of the ball movement, is essential. The control of
the ball motion during the milling leads to a reduction in grinding
energy and a more homogeneous product. Also, the critical inner
diameter of the milling container at a particular rotational speed can
be calculated. In the present work, we use conventional and modified
mechanical alloying to generate a homogenous distribution of 2 wt.
% CNT within Al powders. 99% purity Aluminium powder (Acros,
200mesh) was used along with two different types of multiwall
carbon nanotube (MWCNTs) having different aspect ratios to
produce Al-CNT composites. The composite powders were processed
into bulk material by compaction, and sintering using a cylindrical
compaction and tube furnace. Field Emission Scanning electron
microscopy (FESEM), X-Ray diffraction (XRD), Raman
spectroscopy and Vickers macro hardness tester were used to
evaluate CNT dispersion, powder morphology, CNT damage, phase
analysis, mechanical properties and crystal size determination.
Despite the success of ball milling in dispersing CNTs in Al powder,
it is often accompanied with considerable strain hardening of the Al
powder, which may have implications on the final properties of the
composite. The results show that particle size and morphology vary
with milling time. Also, by using the mixing process and sonication
before mechanical alloying and modified ball mill, dispersion of the
CNTs in Al matrix improves.
Abstract: The fault detection and diagnosis of complicated
production processes is one of essential tasks needed to run the process
safely with good final product quality. Unexpected events occurred in
the process may have a serious impact on the process. In this work,
triangular representation of process measurement data obtained in an
on-line basis is evaluated using simulation process. The effect of using
linear and nonlinear reduced spaces is also tested. Their diagnosis
performance was demonstrated using multivariate fault data. It has
shown that the nonlinear technique based diagnosis method produced
more reliable results and outperforms linear method. The use of
appropriate reduced space yielded better diagnosis performance. The
presented diagnosis framework is different from existing ones in that it
attempts to extract the fault pattern in the reduced space, not in the
original process variable space. The use of reduced model space helps
to mitigate the sensitivity of the fault pattern to noise.
Abstract: This paper presents the application of a signal intensity independent registration criterion for non-rigid body registration of medical images. The criterion is defined as the weighted ratio image of two images. The ratio is computed on a voxel per voxel basis and weighting is performed by setting the ratios between signal and background voxels to a standard high value. The mean squared value of the weighted ratio is computed over the union of the signal areas of the two images and it is minimized using the Chebyshev polynomial approximation. The geometric transformation model adopted is a local cubic B-splines based model.
Abstract: Basic ingredients of concrete are cement, fine aggregate, coarse aggregate and water. To produce a concrete of certain specific properties, optimum proportion of these ingredients are mixed. The important factors which govern the mix design are grade of concrete, type of cement and size, shape and grading of aggregates. Concrete mix design method is based on experimentally evolved empirical relationship between the factors in the choice of mix design. Basic draw backs of this method are that it does not produce desired strength, calculations are cumbersome and a number of tables are to be referred for arriving at trial mix proportion moreover, the variation in attainment of desired strength is uncertain below the target strength and may even fail. To solve this problem, a lot of cubes of standard grades were prepared and attained 28 days strength determined for different combination of cement, fine aggregate, coarse aggregate and water. An artificial neural network (ANN) was prepared using these data. The input of ANN were grade of concrete, type of cement, size, shape and grading of aggregates and output were proportions of various ingredients. With the help of these inputs and outputs, ANN was trained using feed forward back proportion model. Finally trained ANN was validated, it was seen that it gave the result with/ error of maximum 4 to 5%. Hence, specific type of concrete can be prepared from given material properties and proportions of these materials can be quickly evaluated using the proposed ANN.