Abstract: The study examined the effect of Bonny Light whole
crude oil (WC) and its water soluble fraction (WSF) on the activities
of antioxidant enzymes (catalase (CAT) and superoxide dismutase
(SOD)) and crude mitochondria ATPases in the radicle of
germinating bean (Vigna unguiculata). The percentage germination,
level of lipid peroxidation, antioxidant enzyme and mitochondria
Ca2+ and Mg2+ ATPase activities were measured in the radicle of
bean after 7, 14 and 21 days post germination. Viable bean seeds
were planted in soils contaminated with 10ml, 25ml and 50ml of
whole crude oil (WC) and its water soluble fraction (WSF) to obtain
2, 5 and 10% v/w crude oil contamination. There was dose dependent
reduction of the number of bean seeds that germinated in the
contaminated soils compared with control (p
Abstract: This study was conducted to investigate the effect of
the antioxidant activity of germinated African Yam Bean (AYB) on
oxidative stress markers in alloxan induced diabetic rat. Rats were
randomized into three groups; control, diabetic and germinated AYB
– treated diabetic rats. The Total phenol and flavonoid content and
DPPH radical scavenging activity before and after germination were
investigated. The glucose level, lipid peroxidation and reduced
glutathione of the animals were also determined using standard
technique for four weeks. Germination increased the total phenol,
flavonoid and antioxidant activity of AYB extract by 19.14%,
32.28% and 57.25% respectively. The diabetic rats placed on
germinated AYB diet had a significant decrease in the blood glucose
and lipid peroxidation with a corresponding increase in glutathione
(p
Abstract: Thin ZnO films are deposited on glass substrates via
sol–gel method and dip-coating. The films are prepared from zinc
acetate dehydrate as a starting reagent. After that the as-prepared
ZnO sol is aged for different periods (0, 1, 3, 5, 10, 15 and 30 days).
Nanocrystalline thin films are deposited from various sols. The
effect ZnO sols aging time on the structural and photocatalytic
properties of the films is studied. The films surface is studied by
Scanning Electron Microscopy. The effect of the aging time of the
starting solution is studied in the photocatalytic degradation of
Reactive Black 5 (RB5) by UV-vis spectroscopy. The experiments
are conducted upon UV-light illumination and in complete darkness.
The variation of the absorption spectra shows the degradation of RB5
dissolved in water, as a result of the reaction, occurring on the surface
of the films and promoted by UV irradiation. The initial
concentrations of dye (5, 10 and 20 ppm) and the effect of the aging
time are varied during the experiments. The results show, that the
increasing aging time of starting solution with respect to ZnO
generally promotes photocatalytic activity. The thin films obtained
from ZnO sol, which is aged 30 days have best photocatalytic
degradation of the dye (97,22%) in comparison with the freshly
prepared ones (65,92%). The samples and photocatalytic
experimental results are reproducible. Nevertheless, all films exhibit
a substantial activity in both UV light and darkness, which is
promising for the development of new ZnO photocatalysts by sol-gel
method.
Abstract: The concept of urban transformation came about
through interventions aimed at bringing socially and economically
problematic areas of cities into use. The issue of urban transformation
arose frequently during the post-2000 period in particular, and legal
regulations on this matter were also developed in Turkey. Urban
transformation project would be a focal point for the formation of the
city in the near future. Izmir, which is third largest city of Turkey, is
an important trade and port city. But, assessment of the current
situation shows that, the majority of existing residential areas was
formed with squatters and unplanned settlements in Izmir city center.
Therefore an important part of these areas have significant problems
in terms of the quality of life, safety and environmental quality. In
this study, the central policies in Turkey and local policies in Đzmir
about urban transformation will be considered. In addition, urban
renewal projects that are being implemented in Izmir were discussed
and suggestions will be developed in accordance with this policy.
Abstract: Analyzing DNA microarray data sets is a great
challenge, which faces the bioinformaticians due to the complication
of using statistical and machine learning techniques. The challenge
will be doubled if the microarray data sets contain missing data,
which happens regularly because these techniques cannot deal with
missing data. One of the most important data analysis process on
the microarray data set is feature selection. This process finds the
most important genes that affect certain disease. In this paper, we
introduce a technique for imputing the missing data in microarray
data sets while performing feature selection.
Abstract: Currently, there is excessively growing information
about places on Facebook, which is the largest social network but
such information is not explicitly organized and ranked. Therefore
users cannot exploit such data to recommend places conveniently and
quickly. This paper proposes a Facebook application and an Android
application that recommend places based on the number of check-ins
of those places, the distance of those places from the current location,
the number of people who like Facebook page of those places, and
the number of talking about of those places. Related Facebook data is
gathered via Facebook API requests. The experimental results of the
developed applications show that the applications can recommend
places and rank interesting places from the most to the least. We have
found that the average satisfied score of the proposed Facebook
application is 4.8 out of 5. The users’ satisfaction can increase by
adding the app features that support personalization in terms of
interests and preferences.
Abstract: Since columns are the most important elements of the
structures, failure of one column in a critical location can cause a
progressive collapse. In this respect, the repair and strengthening of
columns is a very important subject to reduce the building failure and
to keep the columns capacity. Twenty columns with different
parameters is tested and analysis. Eleven typical confined reinforced
concrete (RC) columns with different types of techniques are
assessment. And also, four confined concrete columns with plastic
tube (PVC) are tested with and with four paralleling tested of
unconfined plain concrete. The techniques of confined RC columns
are mortar strengthening, Steel rings strengthening, FRP
strengthening. Moreover, the technique of confined plain concrete
(PC) column is used PVC tubes. The columns are tested under
uniaxial compressive loads studied the effect of confinement on the
structural behavior of circular RC columns. Test results for each
column are presented in the form of crack patterns, stress-strain
curves. Test results show that confining of the RC columns using
different techniques of strengthening results significant improvement
of the general behavior of the columns and can used in construction.
And also, tested confined PC columns with PVC tubes results shown
that the confined PC with PVC tubes can be used in economical
building. The theoretical model for predicted column capacity is
founded with experimental factor depends on the confined techniques
used and the strain reduction.
Abstract: A knowledge-based expert system with the acronym
RASPE is developed as an application tool to help decision makers in
construction companies make informed decisions about managing
risks in pipeline construction projects. Choosing to use expert
systems from all available artificial intelligence techniques is due to
the fact that an expert system is more suited to representing a
domain’s knowledge and the reasoning behind domain-specific
decisions. The knowledge-based expert system can capture the
knowledge in the form of conditional rules which represent various
project scenarios and potential risk mitigation/response actions. The
built knowledge in RASPE is utilized through the underlying
inference engine that allows the firing of rules relevant to a project
scenario into consideration. Paper provides an overview of the
knowledge acquisition process and goes about describing the
knowledge structure which is divided up into four major modules.
The paper shows one module in full detail for illustration purposes
and concludes with insightful remarks.
Abstract: Modelling of the earth's surface and evaluation of
urban environment, with 3D models, is an important research topic.
New stereo capabilities of high resolution optical satellites images,
such as the tri-stereo mode of Pleiades, combined with new image
matching algorithms, are now available and can be applied in urban
area analysis. In addition, photogrammetry software packages gained
new, more efficient matching algorithms, such as SGM, as well as
improved filters to deal with shadow areas, can achieve more dense
and more precise results.
This paper describes a comparison between 3D data extracted
from tri-stereo and dual stereo satellite images, combined with pixel
based matching and Wallis filter. The aim was to improve the
accuracy of 3D models especially in urban areas, in order to assess if
satellite images are appropriate for a rapid evaluation of urban
environments.
The results showed that 3D models achieved by Pleiades tri-stereo
outperformed, both in terms of accuracy and detail, the result
obtained from a Geo-eye pair. The assessment was made with
reference digital surface models derived from high resolution aerial
photography. This could mean that tri-stereo images can be
successfully used for the proposed urban change analyses.
Abstract: Solar energy is a good option among renewable
energy resources due to its easy availability and abundance. The
simplest and most efficient way to utilize solar energy is to convert it
into thermal energy and this can be done with the help of solar
collectors. The thermal performance of such collectors is poor due to
less heat transfer from the collector surface to air. In this work,
experimental investigations of single pass solar air heater having
triangular duct and provided with roughness element on the underside
of the absorber plate. V-shaped ribs are used for investigation having
three different values of relative roughness pitch (p/e) ranges from 4-
16 for a fixed value of angle of attack (α), relative roughness height
(e/Dh) and a relative gap distance (d/x) values are 60°, 0.044 and 0.60
respectively. Result shows that considerable augmentation in heat
transfer has been obtained by providing roughness.
Abstract: The dielectric properties and ionic conductivity of
novel "ceramic state" polymer electrolytes for high capacity lithium
battery are characterized by Radio frequency and Microwave
methods in two broad frequency ranges from 50 Hz to 20 KHz and 4
GHz to 40 GHz. This innovative solid polymer electrolyte which is
highly ionic conductive (10-3 S/cm at room temperature) from -40oC
to +150oC can be used in any battery application. Such polymer
exhibits properties more like a ceramic rather than polymer. The
various applied measurement methods produced accurate dielectric
results for comprehensive analysis of electrochemical properties and
ion transportation mechanism of this newly invented polymer
electrolyte. Two techniques and instruments employing air gap
measurement by Capacitance Bridge and in-waveguide measurement
by vector network analyzer are applied to measure the complex
dielectric spectra. The complex dielectric spectra are used to
determine the complex alternating current electrical conductivity and
thus the ionic conductivity.
Abstract: Teachers can play a huge role in encouraging students
to use computers and can affect students’ attitudes towards
computers. So understanding teachers’ beliefs and their use of
computers is an important way to create effective motivational
systems for teachers to use computers in the classroom in an effective
way. A qualitative study (6 focus group) was carried out among
Saudi High school teachers, both male and female, to examine their
attitudes towards computers and to find out their computer skills and
usage. The study showed a gender differences in that females were
less likely to attend computer workshops, females also had less
computer skills, and they have more negative attitudes towards
computers than males. Also the study found that low computer skills
in the classroom made students unlikely to have the lessons presented
using computers. Furthermore, the study found some factors that
effected teachers’ attitudes towards computers. These factors were
computer experience and confidence as much having skills and good
experience in computer use, the role and importance of computers
had become in their life and in teaching as well.
Abstract: One image is worth more than thousand words.
Images if analyzed can reveal useful information. Low level image
processing deals with the extraction of specific feature from a single
image. Now the question arises: What technique should be used to
extract patterns of very large and detailed image database? The
answer of the question is: “Image Mining”. Image Mining deals with
the extraction of image data relationship, implicit knowledge, and
another pattern from the collection of images or image database. It is
nothing but the extension of Data Mining. In the following paper, not
only we are going to scrutinize the current techniques of image
mining but also present a new technique for mining images using
Genetic Algorithm.
Abstract: In this paper, two options of anodic alumina barrier
layer thinning have been demonstrated. The approaches varied with
the duration of the voltage step. It was found that too long step of the
barrier layer thinning process leads to chemical etching of the
nanopores on their top. At the bottoms pores are not fully opened
what is disadvantageous for further applications in nanofabrication.
On the other hand, while the duration of the voltage step is controlled
by the current density (value of the current density cannot exceed
75% of the value recorded during previous voltage step) the pores are
fully opened. However, pores at the bottom obtained with this
procedure have smaller diameter, nevertheless this procedure
provides electric contact between the bare aluminum (substrate) and
electrolyte, what is suitable for template assisted electrodeposition,
one of the most cost-efficient synthesis method in nanotechnology.
Abstract: The belief of a heavenly God is enshrined to all
Abrahamic religions which form the three major religions of the
world today. Muslims believe in Allah who is above the seven
heavens. The youth in the United Arab Emirates (UAE) study Islamic
courses as part of their high school curriculum and are required to
take at least one Islamic course at the university level to gain credit
hours towards their general education (GENED). This paper provides
an insight of what the youth studying in the UAE think of where
Allah is. Our analysis shows that a big number of Muslim youth were
not sure, especially those from the Middle Eastern and Arab countries
bringing to conclusion that this subject needs to be revisited again in
the course work.
Abstract: The well been of human beings on construction site is
very important, many man power had been lost through accidents
which kills or make workers physically unfit to carry out construction
activities, these in turn have multiple effects on the whole economy.
Thus it is necessary to put all safety items and regulations in place
before construction activities can commence. This study was carried
out in Ondo state of Nigeria to known and analyse the state of health
and safety of construction workers in the state. The study was done
using first hand observation method, 50 construction project sites
were visited in 10 major towns of Ondo state, questionnaires were
distributed and the results were analysed. The result show that
construction workers are being exposed to a lot of construction site
hazards due to lack of inadequate safety programmes and nonprovision
of appropriate safety materials for workers on site. From the
data gotten for each site visited and the statistical analysis, it can be
concluded that occurrence of accident on construction sites depends
significantly on the available safety facilities on the sites. The result of
the regression statistics show that the level of significant of the
dependence of occurrence of accident on the availability of safety
items on site is 0.0362 which is less than 0.05 maximum significant
level required. Therefore a vital way of sustaining our building
strategy is by given a detail attention to provision of adequate health
and safety items on construction sites which will reduce the
occurrence of accident, loss of man power and death of skilled
workers among others.
Abstract: Background: The effectiveness of mirror therapy
(MT) has been investigated in acute hemiplegia. The present study
examines whether MT, given during chronic stroke, was more
effective in promoting motor recovery of the lower extremity and
walking speed than standard rehabilitation alone. Methods: The study
enrolled 30 patients with chronic stroke. Fifteen patients each were
assigned to the treatment group and the control group. All patients
received a conventional rehabilitation program for a 4-week period.
In addition to this rehabilitation program, patients in the treatment
group received mirror therapy for 4 weeks, 5 days a week. Main
measures: Passive ankle joint dorsiflexion range of motion, gait
speed, Brunnstrom stages of motor recovery, plantar flexor muscle
tone by Modified Ashworth Scale. Results: No significant difference
was found in the outcome measures among groups before treatment.
When compared with standard rehabilitation, mirror therapy
improved Ankle ROM, Brunnstrom stages and waking speed
(p < 0.05). However, there were no significant differences between
two groups on MAS (P > 0.05).Conclusion: Mirror therapy combined
with a conventional stroke rehabilitation program enhances lowerextremity
motor recovery and walking speed in chronic stroke
patients.
Abstract: Sandwich structure composites produced by epoxy
core and aluminium skin were developed as potential building
materials. Interface bonding between core and skin was controlled by
varying kenaf content. Five different weight percentage of kenaf
loading ranging from 10 wt% to 50 wt% were employed in the core
manufacturing in order to study the mechanical properties of the
sandwich composite. Properties of skin aluminium with epoxy were
found to be affected by drying time of the adhesive. Mechanical
behavior of manufactured sandwich composites in relation with
properties of constituent materials was studied. It was found that 30
wt% of kenaf loading contributed to increase the flexural strength and
flexural modulus up to 102 MPa and 32 GPa, respectively. Analysis
were done on the flatwise and edgewise compression test. For
flatwise test, it was found that 30 wt% of fiber loading could
withstand maximum force until 250 kN, with compressive strength
results at 96.94 MPa. However, at edgewise compression test, the
sandwich composite with same fiber loading only can withstand 31
kN of the maximum load with 62 MPa of compressive strength
results.
Abstract: Fiber Bragg optic sensor is embedded in composite
material to detect and monitor the damage that occurs in composite
structures. In this paper, we deal with the mode-Ι delamination to
determine the material strength to crack propagation, using the
coupling mode theory and T-matrix method to simulate the FBGs
spectrum for both uniform and non-uniform strain distribution. The
double cantilever beam test is modeled in FEM to determine the
longitudinal strain. Two models are implemented, the first is the
global half model, and the second is the sub-model to represent the
FBGs with higher refined mesh. This method can simulate damage in
composite structures and converting strain to a wavelength shifting in
the FBG spectrum.
Abstract: This study was carried out to evaluate the nutritional
composition of the African River Prawn (Macrobrachium
vollenhovenii) in relation to Chokor (traditional) and Altona
(improved traditional) drying techniques used in the preservation and
processing of prawns by carrying out proximate composition
analysis. The value obtained for the proximate analysis of Chokor
and Altona smoke dried prawns were; Moisture (14.90% and
15.15%), Dry matter (85.10% and 84.85%), Protein (55.80% and
58.87%), Crude fat (1.95% and 1.98%), Crude fibre (21.40% and
13.11%), Carbohydrate (0.54% and 0.54%) and Ash (19.76% and
15.86%) respectively. The proximate mineral composition of Chokor
and Altona smoke dried prawns were; Calcium (5.66% and 4.20%)
and Phosphorus (9. 22% and 6.34%) respectively. Result shows there
was no loss of nutritional value with respect to Chokor and Altona
drying techniques used in the processing of prawns.