Abstract: We propose a decoy-pulse protocol for frequency-coded implementation of B92 quantum key distribution protocol. A direct extension of decoy-pulse method to frequency-coding scheme results in security loss as an eavesdropper can distinguish between signal and decoy pulses by measuring the carrier photon number without affecting other statistics. We overcome this problem by optimizing the ratio of carrier photon number of decoy-to-signal pulse to be as close to unity as possible. In our method the switching between signal and decoy pulses is achieved by changing the amplitude of RF signal as opposed to modulating the intensity of optical signal thus reducing system cost. We find an improvement by a factor of 100 approximately in the key generation rate using decoy-state protocol. We also study the effect of source fluctuation on key rate. Our simulation results show a key generation rate of 1.5×10-4/pulse for link lengths up to 70km. Finally, we discuss the optimum value of average photon number of signal pulse for a given key rate while also optimizing the carrier ratio.
Abstract: Accurate timing alignment and stability is important
to maximize the true counts and minimize the random counts in
positron emission tomography So signals output from detectors must
be centering with the two isotopes to pre-operation and fed signals
into four units of pulse-processing units, each unit can accept up to
eight inputs. The dual source computed tomography consist two units
on the left for 15 detector signals of Cs-137 isotope and two units on
the right are for 15 detectors signals of Co-60 isotope. The gamma
spectrum consisting of either single or multiple photo peaks. This
allows for the use of energy discrimination electronic hardware
associated with the data acquisition system to acquire photon counts
data with a specific energy, even if poor energy resolution detectors
are used. This also helps to avoid counting of the Compton scatter
counts especially if a single discrete gamma photo peak is emitted by
the source as in the case of Cs-137. In this study the polyenergetic
version of the alternating minimization algorithm is applied to the
dual energy gamma computed tomography problem.
Abstract: To simulate expected climate change, we implemented a two-factor (temperature and soil moisture) field design in a forest in Ontario, Canada. To manipulate moisture input, we erected rain-exclusion structures. Under each structure, plots were watered with one of three treatments and thermally controlled with three heat treatments to simulate changes in air temperature and rainfall based on the climate model (GCM) predictions for the study area. Environmental conditions (including untreated controls) were monitored tracking air temperature, soil temperature, soil moisture, and photosynthetically active radiation. We measured rainfall and relative humidity at the site outside the rain-exclusion structures. Analyses of environmental conditions demonstrates that the temperature manipulation was most effective at maintaining target temperature during the early part of the growing season, but it was more difficult to keep the warmest treatment at 5º C above ambient by late summer. Target moisture regimes were generally achieved however incoming solar radiation was slightly attenuated by the structures.
Abstract: Structural and UV/Visible optical properties can be
useful to describe a material for the CIGS solar cell active layer,
therefore, this work demonstrates the properties like surface
morphology, X-ray Photoelectron Spectroscopy (XPS) bonding
energy (EB) core level spectra, UV/Visible absorption spectra,
refractive index (n), optical energy band (Eg), reflection spectra for
the Cu25 (In16Ga9) Se40Te10 (CIGST-1) and Cu20 (In14Ga9) Se45Te12
(CIGST-2) chalcogenide compositions. Materials have been
exhibited homogenous surface morphologies, broading /-or diffusion
of bonding energy peaks relative elemental values and a high
UV/Visible absorption tendency in the wave length range 400 nm-
850 nm range with the optical energy band gaps 1.37 and 1.42
respectively. Subsequently, UV/Visible reflectivity property in the
wave length range 250 nm to 320 nm for these materials has also
been discussed.
Abstract: Gluconic acid is one of interesting chemical products
in industries such as detergents, leather, photographic, textile, and
especially in food and pharmaceutical industries. Fermentation is an
advantageous process to produce gluconic acid. Mathematical
modeling is important in the design and operation of fermentation
process. In fact, kinetic data must be available for modeling. The
kinetic parameters of gluconic acid production by Aspergillus niger
in batch culture was studied in this research at initial substrate
concentration of 150, 200 and 250 g/l. The kinetic models used were
logistic equation for growth, Luedeking-Piret equation for gluconic
acid formation, and Luedeking-Piret-like equation for glucose
consumption. The Kinetic parameters in the model were obtained by
minimizing non linear least squares curve fitting.
Abstract: Effect of temperature and light was investigated on a
thin film of organic semiconductor formyl-TIPPCu(II) deposited on a
glass substrate with preliminary evaporated gold electrodes. The
electrical capacitance and resistance of the fabricated device were
evaluated under the effect of temperature and light. The relative
capacitance of the fabricated sensor increased by 4.3 times by rising
temperature from 27 to 1870C, while under illumination up to 25000
lx, the capacitance of the Au/formyl-TIPPCu(II)/Au photo capacitive
sensor increased continuously by 13.2 times as compared to dark
conditions.
Abstract: A facile vapour deposition method of synthesis of vertically aligned ZnO nanowires on carbon seed layer was developed. The received samples were investigated on electronic microscope JSM-6490 LA JEOL and x-ray diffractometer X, pert MPD PRO. The photoluminescence spectra (PL) of obtained ZnO samples at a room temperature were studied using He-Cd laser (325 nm line) as excitation source.
Abstract: Roadways in Amman city face many problems consequent upon poor drainage systems. Evaluation tools are necessary to identify those roads needing improvement in their drainage system, and those needing regular maintenance. This work aims at evaluating drainage conditions in selected roadways in Amman city with the intent of identifying the problems encountered in their drainage systems. Three sites in the vicinity of Amman city have been selected and then inspected via several field visits to determine the state of their existing drainage systems and define the major problems encountered in these systems. The evaluation tool used in this study is based on visual inspection supported by photographs that depicted the defined problems. Following the field assessment, the drainage system in each road was rated as excellent, fair, good, or poor. The study reveals that more than 60% of the roadways in the selected sites were in poor drainage conditions, which lead to tremendous environmental problems. This assessment serves as a guide for local decision makers to help plan for the maintenance of Amman city roadways drainage systems, and propose ways of managing the associated problems.
Abstract: ZnO nanocrystals with mean diameter size 14 nm
have been prepared by precipitation method, and examined as
photocatalyst for the UV-induced degradation of insecticide diazinon
as deputy of organic pollutant in aqueous solution. The effects of
various parameters, such as illumination time, the amount of
photocatalyst, initial pH values and initial concentration of
insecticide on the photocatalytic degradation diazinon were
investigated to find desired conditions. In this case, the desired
parameters were also tested for the treatment of real water containing
the insecticide. Photodegradation efficiency of diazinon was
compared between commercial and prepared ZnO nanocrystals. The
results indicated that UV/ZnO process applying prepared
nanocrystalline ZnO offered electrical energy efficiency and
quantum yield better than commercial ZnO. The present study, on the
base of Langmuir-Hinshelwood mechanism, illustrated a pseudo
first-order kinetic model with rate constant of surface reaction equal
to 0.209 mg l-1 min-1 and adsorption equilibrium constant of 0.124 l
mg-1.
Abstract: We developed an effective microfluidic device for photoreactions with low reflectance and good heat conductance. The performance of this microfluidic device was tested by carrying out a photoreactive synthesis of benzopinacol and acetone from benzophenone and 2-propanol. The yield reached 36% with an irradiation time of 469.2 s and was improved by more than 30% when compared to the values obtained by the batch method. Therefore, the microfluidic device was found to be effective for improving the yields of photoreactions.
Abstract: In the recent years, high dynamic range imaging has
gain popularity with the advancement in digital photography. In this
contribution we present a subjective evaluation of various tone
production and tone mapping techniques by a number of participants.
Firstly, standard HDR images were used and the participants were
asked to rate them based on a given rating scheme. After that, the
participant was asked to rate HDR image generated using linear and
nonlinear combination approach of multiple exposure images. The
experimental results showed that linearly generated HDR images
have better visualization than the nonlinear combined ones. In
addition, Reinhard et al. and the exponential tone mapping operators
have shown better results compared to logarithmic and the Garrett et
al. tone mapping operators.
Abstract: This paper presents Simulated Annealing based
approach to estimate solar cell model parameters. Single diode solar
cell model is used in this study to validate the proposed approach
outcomes. The developed technique is used to estimate different
model parameters such as generated photocurrent, saturation current,
series resistance, shunt resistance, and ideality factor that govern the
current-voltage relationship of a solar cell. A practical case study is
used to test and verify the consistency of accurately estimating
various parameters of single diode solar cell model. Comparative
study among different parameter estimation techniques is presented
to show the effectiveness of the developed approach.
Abstract: For the electrical metrics that describe photovoltaic
cell performance are inherently multivariate in nature, use of a
univariate, or one variable, statistical process control chart can have
important limitations. Development of a comprehensive process
control strategy is known to be significantly beneficial to reducing
process variability that ultimately drives up the manufacturing cost
photovoltaic cells. The multivariate moving average or MMA chart,
is applied to the electrical metrics of photovoltaic cells to illustrate
the improved sensitivity on process variability this method of control
charting offers. The result show the ability of the MMA chart to
expand to as any variables as needed, suggests an application
with multiple photovoltaic electrical metrics being used in
concert to determine the processes state of control.
Abstract: This paper presents a model for the characterization
and selection of beeswaxes for use as base substitute tissue for the
manufacture of objects suitable for external radiotherapy using
megavoltage photon beams. The model of characterization was
divided into three distinct stages: 1) verification of aspects related to
the origin of the beeswax, the bee species, the flora in the vicinity of
the beehives and procedures to detect adulterations; 2) evaluation of
physical and chemical properties; and 3) evaluation of beam
attenuation capacity. The chemical composition of the beeswax
evaluated in this study was similar to other simulators commonly
used in radiotherapy. The behavior of the mass attenuation coefficient
in the radiotherapy energy range was comparable to other simulators.
The proposed model is efficient and enables convenient assessment
of the use of any particular beeswax as a base substitute tissue for
radiotherapy.
Abstract: The surface water used in this study was collected from the Chao Praya River at the lower part at the Nonthaburi bridge. It was collected and used throughout the experiment. TOC (also known as DOC) in the range between 2.5 to 5.6 mg/l were investigated in this experiment. The use of conventional treatment methods such as FeCl3 and PAC showed that TOC removal was 65% using FeCl3 and 78% using PAC (powder activated carbon). The advanced oxidation process alone showed only 35% removal of TOC. Coupling advanced oxidation with a small amount of PAC (0.05g/L) increased efficiency by upto 55%. The combined BAC with advanced oxidation process and small amount of PAC demonstrated the highest efficiency of up to 95% of TOC removal and lower sludge production compared with other methods.
Abstract: To distinguish small retinal hemorrhages in early
diabetic retinopathy from dust artifacts, we analyzed hue, lightness,
and saturation (HLS) color spaces. The fundus of 5 patients with
diabetic retinopathy was photographed. For the initial experiment, we
placed 4 different colored papers on the ceiling of a darkroom. Using
each color, 10 fragments of house dust particles on a magnifier were
photographed. The colored papers were removed, and 3 different
colored light bulbs were suspended from the ceiling. Ten fragments of
house dust particles on the camera-s object lens were photographed.
We then constructed an experimental device that can photograph
artificial eyes. Five fragments of house dust particles under the ocher
fundus of the artificial eye were photographed. On analyzing HLS
color space of the dust artifact, lightness and saturation were found to
be highly sensitive. However, hue was not highly sensitive.
Abstract: In a lowland dipterocarp forest, we assessed the impact of canopy openness (CO) and the resultant changes under different logging systems using hemispherical photography. CO was assessed in a primary forest and two forests logged selectively using reduced impact logging. At one site, 3-m-wide strip cutting was conducted for line planting. From the comparison of CO among the three sites, we found significant changes caused by logging. However, no significant difference was observed between the two logged sites. Strip cutting treatment did not affect CO. One year after, significant canopy closure occurred in both of the logged sites. Canopy closure was significant regardless of the disturbance element, logging gap, skid trail, or strip cutting line. Significant establishment of seedlings within a year was observed in the strip cutting line. Seedling establishment seemed to contribute to rapid canopy closure and prospected to affect to the survival and growth of planted trees.
Abstract: ZnO nanostructures including nanowires, nanorods,
and nanoneedles were successfully deposited on GaAs substrates,
respectively, by simple two-step chemical method for the first time. A
ZnO seed layer was firstly pre-coated on the O2-plasma treated
substrate by sol-gel process, followed by the nucleation of ZnO
nanostructures through hydrothermal synthesis. Nanostructures with
different average diameter (15-250 nm), length (0.9-1.8 μm), density
(0.9-16×109 cm-2) were obtained via adjusting the growth time and
concentration of precursors. From the reflectivity spectra, we
concluded ordered and taper nanostructures were preferential for
photovoltaic applications. ZnO nanoneedles with an average diameter
of 106 nm, a moderate length of 2.4 μm, and the density of 7.2×109
cm-2 could be synthesized in the concentration of 0.04 M for 18 h.
Integrated with the nanoneedle array, the power conversion efficiency
of single junction solar cell was increased from 7.3 to 12.2%,
corresponding to a 67% improvement.
Abstract: The paper presents a modelling methodology for
small scale multi-source renewable energy systems. Using historical
site-specific weather data, the relationships of cost, availability and
energy form are visualised as a function of the sizing of photovoltaic
arrays, wind turbines, and battery capacity. The specific dependency
of each site on its own particular weather patterns show that unique
solutions exist for each site. It is shown that in certain cases the
capital component cost can be halved if the desired theoretical
demand availability is reduced from 100% to 99%.
Abstract: Considering complexity of products, new geometrical
design and investment tolerances that are necessary, measuring and
dimensional controlling involve modern and more precise methods.
Photo digitizing method using two cameras to record pictures and
utilization of conventional method named “cloud points" and data
analysis by the use of ATOUS software, is known as modern and
efficient in mentioned context. In this paper, benefits of photo
digitizing method in evaluating sampling of machining processes
have been put forward. For example, assessment of geometrical
integrity surface in 5-axis milling process and measurement of
carbide tool wear in turning process, can be can be brought forward.
Advantages of this method comparing to conventional methods have
been expressed.