Abstract: This paper investigates the characteristics of wall
pressure fluctuations in naturally developing boundary layer flows
on axisymmetric bodies experimentally. The axisymmetric body has
a modified ellipsoidal blunt nose. Flush-mounted microphones are
used to measure the wall pressure fluctuations in the boundary layer
flow over the body. The measurements are performed in a low noise
wind tunnel. It is found that the correlation between the flow regime
and the characteristics of the pressure fluctuations is distinct. The
process from small fluctuation in laminar flow to large fluctuation in
turbulent flow is investigated. Tollmien-Schlichting wave (T-S wave)
is found to generate and develop in transition. Because of the T-S
wave, the wall pressure fluctuations in the transition region are higher
than those in the turbulent boundary layer.
Abstract: Bottom ash from Municipal Solid Waste Incineration
(MSWI) can be viewed as a typical granular material because these
industrial by-products result from the incineration of various
domestic wastes. MSWI bottom ash is mainly used in road
engineering in substitution of the traditional natural aggregates. As
the characterization of their mechanical behavior is essential in order
to use them, specific studies have been led over the past few years. In
the first part of this paper, the mechanical behavior of MSWI bottom
ash is studied with triaxial tests. After, analysis of the experiment
results, the simulation of triaxial tests is carried out by using the
software package CESAR-LCPC. As the first approach in modeling
of this new class material, the Mohr-Coulomb model was chosen to
describe the evolution of material under the influence of external
mechanical actions.
Abstract: Result from the constant dwindle in natural resources,
the alternative way to reduce the costs in our daily life would be urgent
to be found in the near future. As the ancient technique based on the
theory of solar chimney since roman times, the double-skin façade are
simply composed of two large glass panels in purpose of daylighting
and also natural ventilation in the daytime. Double-skin façade is
generally installed on the exterior side of buildings as function as the
window, so there is always a huge amount of passive solar energy the
façade would receive to induce the airflow every sunny day. Therefore,
this article imposes a domestic double-skin window for residential
usage and attempts to improve the volume flow rate inside the cavity
between the panels by the frame geometry design, the installation of
outlet guide plate and the solar energy collection system. Note that the
numerical analyses are applied to investigate the characteristics of flow
field, and the boundary conditions in the simulation are totally based
on the practical experiment of the original prototype. Then we
redesign the prototype from the knowledge of the numerical results
and fluid dynamic theory, and later the experiments of modified
prototype will be conducted to verify the simulation results. The
velocities at the inlet of each case are increase by 5%, 45% and 15%
from the experimental data, and also the numerical simulation results
reported 20% improvement in volume flow rate both for the frame
geometry design and installation of outlet guide plate.
Abstract: Issues relating to the destructive phenomena that can
damage people and goods have returned to the centre of debate in
Italy with the increase in catastrophic episodes in recent years in a
country which is highly vulnerable to hydrological risk.
Environmental factors and geological and geomorphological
territorial characteristics play an important role in determining the
level of vulnerability and the natural tendency to risk. However, a
territory has also been subjected to the requirements of and
transformations of society and this brings other relevant factors. The
reasons for the increase in destructive phenomena are often to be
found in the territorial development models adopted. Stewardship of
the landscape and management of risk are related issues. This study aims to summarize the most relevant elements about
this connection and at the same time to clarify the role of
environmental risk assessment as a tool to aid in the sustainable
management of landscape. Finally, the study reflects on how regional
and urban planners deal with environmental risk and which aspects
should be monitored in order to adopt responsible and useful
interventions.
Abstract: This paper describes the development of new class of
epoxy based rice husk filled jute reinforced composites. Rice husk
flour is added in 0%, 1%, 3%, 5% by weight. Epoxy resin and
triethylenetetramine (T.E.T.A) is used as matrix and hardener
respectively. It investigates the mechanical properties of the
composites and a comparison is done for monolithic jute composite
and the filled ones. The specimens are prepared according to the
ASTM standards and experimentation is carried out using INSTRON
8801. The result shows that with the increase of filler percentage the
tensile properties increases but compressive and flexural properties
decreases.
Abstract: This paper focuses on the mathematical modeling for
solidification of Al alloy in a cube mold cavity to study the
solidification behavior of casting process. The parametric
investigation of solidification process inside the cavity was
performed by using computational solidification/melting model
coupled with Volume of fluid (VOF) model. The implicit filling
algorithm is used in this study to understand the overall process from
the filling stage to solidification in a model metal casting process.
The model is validated with past studied at same conditions. The
solidification process is analyzed by including the effect of pouring
velocity as well as natural convection from the wall and geometry of
the cavity. These studies show the possibility of various defects
during solidification process.
Abstract: As one of the convenient and noninvasive sensing
approaches, the automatic limb girth measurement has been applied
to detect intention behind human motion from muscle deformation.
The sensing validity has been elaborated by preliminary researches
but still need more fundamental studies, especially on kinetic
contraction modes. Based on the novel fabric strain sensors, a soft
and smart limb girth measurement system was developed by the
authors’ group, which can measure the limb girth in-motion.
Experiments were carried out on elbow isometric flexion and elbow
isokinetic flexion (biceps’ isokinetic contractions) of 90°/s, 60°/s, and
120°/s for 10 subjects (2 canoeists and 8 ordinary people). After
removal of natural circumferential increments due to elbow position,
the joint torque is found not uniformly sensitive to the limb
circumferential strains, but declining as elbow joint angle rises,
regardless of the angular speed. Moreover, the maximum joint torque
was found as an exponential function of the joint’s angular speed.
This research highly contributes to the application of the automatic
limb girth measuring during kinetic contractions, and it is useful to
predict the contraction level of voluntary skeletal muscles.
Abstract: Rivers have transient storage or dead zones where
injected pollutants or solutes are entrapped for considerable period of
time, known as residence time, before being released into the main
flowing zones of rivers. In this study, a new empirical expression for
residence time, implementing genetic programming on published
dispersion data, has been derived. The proposed expression uses few
hydraulic and geometric characteristics of rivers which are normally
known to the authorities. When compared with some reported
expressions, based on various statistical indices, it can be concluded
that the proposed expression predicts the residence time of pollutants
in natural rivers more accurately.
Abstract: Large quantities of solid wastes being generated
worldwide from sources such as household, domestic, industrial,
commercial and construction demolition activities, leads to
environmental concerns. Utilization of these wastes in making
building construction materials can reduce the magnitude of the
associated problems. When these waste products are used in place of
other conventional materials, natural resources and energy are
preserved and expensive and/or potentially harmful waste disposal is
avoided. Recycling which is regarded as the third most preferred waste
disposal option, with its numerous environmental benefits, stand as a
viable option to offset the environmental impact associated with the
construction industry. This paper reviews the results of laboratory tests and important
research findings, and the potential of using these wastes in building
construction materials with focus on sustainable development.
Research gaps, which includes; the need to develop standard mix
design for solid waste based building materials; the need to develop
energy efficient method of processing solid waste use in concrete; the
need to study the actual behavior or performance of such building
materials in practical application and the limited real life application
of such building materials have also been identified. A research is being proposed to develop an environmentally
friendly, lightweight building block from recycled waste paper,
without the use of cement, and with properties suitable for use as
walling unit. This proposed research intends to incorporate,
laboratory experimentation and modeling to address the identified
research gaps.
Abstract: Biochar can be produced from the waste matter and its
application has been associated with returning of carbon in large
amounts into the soil. The impacts of this material on physical and
chemical properties of soil have been described. The biggest part of
the research work is dedicated to the hypothesis of this material’s
toxic effects on the soil life regarding its effect on the soil biological
component. At present, it has been worked on methods which could
eliminate these undesirable properties of biochar. One of the
possibilities is to mix biochar with organic material, such as compost,
or focusing on the natural processes acceleration in the soil. In the
experiment has been used as the addition of compost as well as the
elimination of toxic substances by promoting microbial activity in
aerated water environment. Biochar was aerated for 7 days in a
container with a volume of 20 l. This way modified biochar had six
times higher biomass production and reduce mineral nitrogen
leaching. Better results have been achieved by mixing biochar with
compost.
Abstract: Ensuring of continuity of business is basic strategy of
every company. Continuity of organization activities includes
comprehensive procedures that help in solving unexpected situations
of natural and anthropogenic character (for example flood, blaze,
economic situations). Planning of continuity operations is a process
that helps identify critical processes and implement plans for the
security and recovery of key processes. The aim of this article is to
demonstrate application of system approach to managing business
continuity called business continuity management systems in military
issues. This article describes the life cycle of business continuity
management which is based on the established cycle PDCA (Plan-
Do-Check-Act). After this is carried out by activities which are
making by University of Defence during activation of forces and
means of the integrated rescue system in case of emergencies -
accidents at a nuclear power plant in Czech Republic. Activities of
various stages of deployment earmarked forces and resources are
managed and evaluated by using MCMS application (Military
Continuity Management System).
Abstract: Durian skin is a newly explores natural fibre
potentially reinforced polyolefin for diverse applications. In this
work, investigation on the effect of coupling agent, maleic anhydride
polypropylene (MAPP) on the mechanical, morphological, and
thermal properties of polypropylene (PP) reinforced with durian skin
fibre (DSF) was conducted. The presence of 30 wt% DSF
significantly reduced the tensile strength of PP-DSF composite.
Interestingly, even though the same trend goes to PP-DSF with the
presence of MAPP, the reduction is only about 4% relative to
unreinforced PP and 18% higher than PP-DSF without MAPP
(untreated composite or UTC). The used of MAPP in treated
composite (TC) also increased the tensile modulus, flexural
properties and degradation temperature. The enhanced mechanical
properties are consistent with good interfacial interaction as
evidenced under scanning electron microscopy.
Abstract: In this article was evaluated the protective effect of
the alternative concrete obtained from the binary mixture of fly ash,
and iron and steel slag. After mixing the cement with aggregates,
structural steel was inserted in the matrix cementitious. The study
was conducted comparatively with specimens exposed to natural
conditions free of chloride ion. The chloride ion effect on the
specimens accelerated under controlled conditions (3.5% NaCl and
25°C temperature). The impedance data were acquired in a range of 1
mHz to 100 kHz.
Abstract: Nature constantly changes as a result of human
necessities. This change mostly feels in natural water sources which
are reconstructed with an effect of dams and motorways. In other
respects, visual quality of the landscape gets a new and different
character during and after the construction of dams and motorways.
Changing and specialization new landscapes will be very important
to protection-usage balance to explore sustainable usage facilities.
The main cause of the selection of Artvin city is that it has very
important geographical location and one of the most attraction points
in the World with its biodiversity, conservation areas and natural
landscape characteristics. Many hydroelectric station and 7 dams are
situated, 3 of them have already been built on the Çoruh River in the
province of Artvin. As a result of dams, motorways route were reshaped
and the ways which have already changed because of
elevation is directly affected several of natural destruction. In
contrast, many different reservoirs in Coruh Basin provide new vista
point that has high visual quality. In this study, we would like to
evaluate with sustainable landscape design in 76 km river corridor,
which is mainly based on Deriner, Borçka and Muratlı Dams and
determination of their basin-lakes recreational potential and
opportunities. Lastly, we are going to give some suggestion about the
potential of the corridor.
Abstract: Various nanomaterials can be used as a drug delivery
vehicles in nanomedicine, called nanocarriers. They can either be
organic or inorganic, synthetic or natural-based. Although synthetic
nanocarriers are easier to produce, they can often be toxic for the
organism and thus not suitable for use in treatment. From naturalbased
nanocarriers, the most commonly used are protein cages or
viral capsids. In this work, virus bacteriophage λ was used for
delivery of different cytotoxic drugs (cisplatin, carboplatin,
oxaliplatin and doxorubicin). Large quantities of phage λ were
obtained from phage λ-producing strain of E. coli cultivated in
medium with 0.2% maltose. After killing of E. coli with chloroform
and its removal by centrifugation, the phage was concentrated by
ultracentrifugation at 130 000×g and 4°C for 3 h. The encapsulation
of the drugs was performed by infusion method and four different
concentrations of the drugs were encapsulated (200; 100; 50; 25
μg·mL-1). Free drug molecules were removed by filtration. The
encapsulation was verified using the absorbance for doxorubicin and
atomic absorption spectrometry for platinum cytostatics. The amount
of encapsulated drug linearly increased with the increasing
concentration of applied drug with the determination coefficient
R2=0.989 for doxorubicin; R2=0.967 for cisplatin; R2=0.989 for
carboplatin and R2=0.996 for oxaliplatin. The overall encapsulation
efficiency was calculated as 50% for doxorubicin; 8% for cisplatin;
6% for carboplatin and 10% for oxaliplatin.
Abstract: The increase of technogenic and natural accidents,
accompanied by air pollution, for example, by combustion products,
leads to the necessity of respiratory protection. This work is devoted to the development of a calorimetric method
and a device which allows investigating quickly the kinetics of
carbon dioxide sorption by chemisorbents on the base of potassium
superoxide in order to assess the protective properties of respiratory
protective closed circuit apparatus. The features of the traditional approach for determining the
sorption properties in a thin layer of chemisorbent are described, as
well as methods and devices, which can be used for the sorption
kinetics study. The authors developed an approach (as opposed to the traditional
approach) based on the power measurement of internal heat sources
in the chemisorbent layer. The emergence of the heat sources is a
result of exothermic reaction of carbon dioxide sorption. This
approach eliminates the necessity of chemical analysis of samples
and can significantly reduce the time and material expenses during
chemisorbents testing. Error of determining the volume fraction of adsorbed carbon
dioxide by the developed method does not exceed 12%. Taking into
account the efficiency of the method, we consider that it is a good
alternative to traditional methods of chemical analysis under the
assessment of the protection sorbents quality.
Abstract: Local steel slag is produced as a by-product during the
oxidation of steel pellets in an electric arc furnace. Using local steel
slag waste as a hundred substitutes of crashed stone in construction
materials would resolve the environmental problems caused by the
large-scale depletion of the natural sources of crashed stone. This
paper reports the experimental study to investigate the influence of a
hundred replacement of crashed stone as a coarse aggregate with
local steel slag, on the fresh and hardened geopolymer concrete
properties. The investigation includes traditional testing of hardening
concrete, for selected mixes of cement and geopolymer concrete. It
was found that local steel slag as a coarse aggregate enhanced the
slump test of the fresh state of cement and geopolymer concretes.
Nevertheless, the unit weight of concretes was affected. Meanwhile,
the good performance was observed when fly ash used as geopolymer
concrete based.
Abstract: Intermediate cities which also called medium size
cities have an important role in the process of globalization. It is
argued that, in some cases this type of cities may be depopulated or in
otherwise may be transformed as the periphery of metropolitans, so
that the personal identity of the city and its local cultural heritage
could suffer from its neighbor metropolitan. Over the last decades,
the role of tourism in the development process and the cultural
heritage has increased. The impact of tourism on socioeconomic
growth makes motivation for the study of tourism development in
regional and urban planning process. There are evidences that
tourism has a positive impact in local development and makes
economic motivations for cultural heritage protection. In this study,
by considering the role of tourism in local development, especially by
its economic and socio-cultural impacts, it is tried to introduce a
strategy for tourism development through a method of urban planning
for intermediate cities called as Base plan. Damavand is an
intermediate city located in Tehran province, Iran with a high
potential in tourism by its local specific characteristic like social
structure, antiquities and natural attractions. It’s selected as a suitable
case study for intended strategy which is a combination of urban
planning and tourism development methods. Focusing on recognition
of the historical and cultural heritage of Damavand, in this paper
through “base plan methodology” a strategy of urban planning
toward tourism development is prepared in order to make tourism
development as a support for cultural heritage of this city.
Abstract: Radio Frequency Identification (RFID) has become a
key technology in the emerging concept of Internet of Things (IoT).
Naturally, business applications would require the deployment of
various RFID systems developed by different vendors that use
different data formats and structures. This heterogeneity poses a
challenge in developing real-life IoT systems with RFID, as
integration is becoming very complex and challenging. Semantic
integration is a key approach to deal with this challenge. To do so,
ontology for RFID systems need to be developed in order to
annotated semantically RFID systems, and hence, facilitate their
integration. Accordingly, in this paper, we propose ontology for
RFID systems. The proposed ontology can be used to semantically
enrich RFID systems, and hence, improve their usage and reasoning.
Abstract: As computing technology advances, smartphone
applications can assist student learning in a pervasive way. For
example, the idea of using mobile apps for the PA Common Trees,
Pests, Pathogens, in the field as a reference tool allows middle school
students to learn about trees and associated pests/pathogens without
bringing a textbook. While working on the development of three heterogeneous mobile
apps, we ran into numerous challenges. Both the traditional waterfall
model and the more modern agile methodologies failed in practice.
The waterfall model emphasizes the planning of the duration for each
phase. When the duration of each phase is not consistent with the
availability of developers, the waterfall model cannot be employed.
When applying Agile Methodologies, we cannot maintain the high
frequency of the iterative development review process, known as
‘sprints’. In this paper, we discuss the challenges and solutions. We
propose a hybrid model known as the Relay Race Methodology to
reflect the concept of racing and relaying during the process of
software development in practice. Based on the development project,
we observe that the modeling of the relay race transition between any
two phases is manifested naturally. Thus, we claim that the RRM
model can provide a de fecto rather than a de jure basis for the core
concept in the software development model. In this paper, the background of the project is introduced first.
Then, the challenges are pointed out followed by our solutions.
Finally, the experiences learned and the future works are presented.