Abstract: This paper investigates vortex shedding processes
occurring at the end of a stack of parallel plates, due to an oscillating
flow induced by an acoustic standing wave within an acoustic
resonator. Here, Particle Image Velocimetry (PIV) is used to quantify
the vortex shedding processes within an acoustic cycle
phase-by-phase, in particular during the “ejection" of the fluid out of
the stack. Standard hot-wire anemometry measurement is also applied
to detect the velocity fluctuations near the end of the stack.
Combination of these two measurement techniques allowed a detailed
analysis of the vortex shedding phenomena. The results obtained show
that, as the Reynolds number varies (by varying the plate thickness
and drive ratio), different flow patterns of vortex shedding are
observed by the PIV measurement. On the other hand, the
time-dependent hot-wire measurements allow obtaining detailed
frequency spectra of the velocity signal, used for calculating
characteristic Strouhal numbers. The impact of the plate thickness and
the Reynolds number on the vortex shedding pattern has been
discussed. Furthermore, a detailed map of the relationship between the
Strouhal number and Reynolds number has been obtained and
discussed.
Abstract: This paper presents an experimental investigation of
transformer dielectric response and solid insulation water content.
The dielectric response was carried out on the base of Hybrid
Frequency Dielectric Spectroscopy and Polarization Current
measurements method (FDS &PC). The calculation of the water
content in paper is based on the water content in oil and the obtained
equilibrium curves. A reference measurements were performed at
equilibrium conditions for water content in oil and paper of
transformer at different stable temperatures (25, 50, 60 and 70°C) to
prepare references to evaluate the insulation behavior at the not
equilibrium conditions. Some measurements performed at the
different simulated normal working modes of transformer operation
at the same temperature where the equilibrium conditions. The
obtained results show that when transformer temperature is mach
more than the its ambient temperature, the transformer temperature
decreases immediately after disconnecting the transformer from the
network and this temperature reduction influences the transformer
insulation condition in the measuring process. In addition to the oil
temperature at the near places to the sensors, the temperature
uniformity in transformer which can be changed by a big change in
the load of transformer before the measuring time will influence the
result. The investigations have shown that the extremely influence of
the time between disconnecting the transformer and beginning the
measurements on the results. And the online monitoring for water
content in paper measurements, on the basis of the oil water content
on line monitoring and the obtained equilibrium curves. The
measurements where performed continuously and for about 50 days
without any disconnection in the prepared the adiabatic room.
Abstract: A new analysis of perceptual speech enhancement is
presented. It focuses on the fact that if only noise above the masking
threshold is filtered, then noise below the masking threshold, but
above the absolute threshold of hearing, can become audible after the
masker filtering. This particular drawback of some perceptual filters,
hereafter called the maskee-to-audible-noise (MAN) phenomenon,
favours the emergence of isolated tonals that increase musical noise.
Two filtering techniques that avoid or correct the MAN phenomenon
are proposed to effectively suppress background noise without introducing
much distortion. Experimental results, including objective
and subjective measurements, show that these techniques improve
the enhanced speech quality and the gain they bring emphasizes the
importance of the MAN phenomenon.
Abstract: The modeling of water transfer in the unsaturated zone
uses techniques and methods of the soil physics to solve the
Richards-s equation. However, there is a disaccord between the size
of the measurements provided by the soil physics and the size of the
fields of hydrological modeling problem, to which is added the
strong spatial variability of soil hydraulic properties. The objective of
this work was to develop a methodology to estimate the
hydrodynamic parameters for modeling water transfers at different
hydrological scales in the soil-plant atmosphere systems.
Abstract: In this article, using finite element analysis (FEA)
and an X-ray diffractometer (XRD), cold-sprayed titanium particles
on a steel substrate is investigated in term of cooling time and the
development of residual strains. Three cooling-down models of
sprayed particles after deposition stage are simulated and discussed:
the first model (m1) considers conduction effect to the substrate only,
the second model (m2) considers both conduction as well as
convection effect to the environment, and the third model (m3) which
is the same as the second model but with the substrate heated to a
near particle temperature before spraying. Thereafter, residual strains
developed in the third model is compared with the experimental
measurement of residual strains, which involved a Bruker D8
Advance Diffractometer using CuKa radiation (40kV, 40mA)
monochromatised with a graphite sample monochromator. For
deposition conditions of this study, a good correlation was found to
exist between the FEA results and XRD measurements of residual
strains.
Abstract: In this paper we study different similarity based approaches for the development of QSAR model devoted to the prediction of activity of antiobesity drugs. Classical similarity approaches are compared regarding to dissimilarity models based on the consideration of the calculation of Euclidean distances between the nonisomorphic fragments extracted in the matching process. Combining the classical similarity and dissimilarity approaches into a new similarity measure, the Approximate Similarity was also studied, and better results were obtained. The application of the proposed method to the development of quantitative structure-activity relationships (QSAR) has provided reliable tools for predicting of inhibitory activity of drugs. Acceptable results were obtained for the models presented here.
Abstract: In this paper an extensive verification of the extraction
method (published earlier) that consistently accounts for self-heating
and Early effect to accurately extract both base and thermal resistance
of bipolar junction transistors is presented. The method verification is
demonstrated on advanced RF SiGe HBTs were the extracted results
for the thermal resistance are compared with those from another
published method that ignores the effect of Early effect on internal
base-emitter voltage and the extracted results of the base resistance
are compared with those determined from noise measurements. A
self-consistency of our method in the extracted base resistance and
thermal resistance using compact model simulation results is also
carried out in order to study the level of accuracy of the method.
Abstract: Elastic light single-scattering spectroscopy system
with a single optical fiber probe was employed to differentiate cancerous prostate tissue from non-cancerous prostate tissue ex-vivo just after radical prostatectomy. First, ELSSS spectra were acquired
from cancerous prostate tissue to define its spectral features. Then,
spectra were acquired from normal prostate tissue to define difference in spectral features between the cancerous and normal
prostate tissues. Of the total 66 tissue samples were evaluated from
nine patients by ELSSS system. Comparing of histopathology results
and ELSSS measurements revealed that sign of the spectral slopes of
cancerous prostate tissue is negative and non-cancerous tissue is positive in the wavelength range from 450 to 750 nm. Based on the
correlation between histopathology results and sign of the spectral
slopes, ELSSS system differentiates cancerous prostate tissue from
non- cancerous with a sensitivity of 0.95 and a specificity of 0.94.
Abstract: More and more natural disasters are happening every
year: floods, earthquakes, volcanic eruptions, etc. In order to reduce
the risk of possible damages, governments all around the world are
investing into development of Early Warning Systems (EWS) for
environmental applications. The most important task of the EWS is
identification of the onset of critical situations affecting environment
and population, early enough to inform the authorities and general
public. This paper describes an approach for monitoring of flood
protections systems based on machine learning methods. An
Artificial Intelligence (AI) component has been developed for
detection of abnormal dike behaviour. The AI module has been
integrated into an EWS platform of the UrbanFlood project (EU
Seventh Framework Programme) and validated on real-time
measurements from the sensors installed in a dike.
Abstract: This study reports the preparation of soft magnetic
ribbons of Fe-based amorphous alloys using the single-roller melt-spinning technique. Ribbon width varied from 142 mm to 213
mm and, with a thickness of approximately 22 μm ± 2 μm. The microstructure and magnetic properties of the ribbons were
characterized by differential scanning calorimeter (DSC), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and electrical resistivity measurements (ERM). The amorphous material
properties dependence of the cooling rate and nozzle pressure have uneven surface in ribbon thicknesses are investigated. Magnetic
measurement results indicate that some region of the ribbon exhibits good magnetic properties, higher saturation induction and lower coercivity. However, due to the uneven surface of 213 mm wide
ribbon, the magnetic responses are not uniformly distributed. To
understand the transformer magnetic performances, this study analyzes the measurements of a three-phase 2 MVA amorphous-cored transformer. Experimental results confirm that the transformer with a
ribbon width of 142 mm has better magnetic properties in terms of lower core loss, exciting power, and audible noise.
Abstract: Usually, the solid-fuel flow of an iron ore sinter plant
consists of different types of the solid-fuels, which differ from each
other. Information about the composition of the solid-fuel flow
usually comes every 8-24 hours. It can be clearly seen that this
information cannot be used to control the sintering process in real
time. Due to this, we propose an expert system which uses indirect
measurements from the process in order to obtain the composition of
the solid-fuel flow by solving an optimization task. Then this
information can be used to control the sintering process. The
proposed technique can be successfully used to improve sinter
quality and reduce the amount of solid-fuel used by the process.
Abstract: Power system state estimation is the process of
calculating a reliable estimate of the power system state vector
composed of bus voltages' angles and magnitudes from telemetered
measurements on the system. This estimate of the state vector
provides the description of the system necessary for the operation
and security monitoring. Many methods are described in the
literature for solving the state estimation problem, the most important
of which are the classical weighted least squares method and the nondeterministic
genetic based method; however both showed
drawbacks. In this paper a modified version of the genetic
algorithm power system state estimation is introduced, Sensitivity of
the proposed algorithm to genetic operators is discussed, the
algorithm is applied to case studies and finally it is compared with
the classical weighted least squares method formulation.
Abstract: In this paper, the detection of a fault in the Global Positioning System (GPS) measurement is addressed. The class of faults considered is a bias in the GPS pseudorange measurements. This bias is modeled as an unknown constant. The fault could be the result of a receiver fault or signal fault such as multipath error. A bias bank is constructed based on set of possible fault hypotheses. Initially, there is equal probability of occurrence for any of the biases in the bank. Subsequently, as the measurements are processed, the probability of occurrence for each of the biases is sequentially updated. The fault with a probability approaching unity will be declared as the current fault in the GPS measurement. The residual formed from the GPS and Inertial Measurement Unit (IMU) measurements is used to update the probability of each fault. Results will be presented to show the performance of the presented algorithm.
Abstract: Two-interconnected fluidized bed systems are widely used in various processes such as Fisher-Tropsch, hot gas desulfurization, CO2 capture-regeneration with dry sorbent, chemical-looping combustion, sorption enhanced steam methane reforming, chemical-looping hydrogen generation system, and so on. However, most of two-interconnected fluidized beds systems require riser and/or pneumatic transport line for solid conveying and loopseals or seal-pots for gas sealing, recirculation of solids to the riser, and maintaining of pressure balance. The riser (transport bed) is operated at the high velocity fluidization condition and residence times of gas and solid in the riser are very short. If the reaction rate of catalyst or sorbent is slow, the riser can not ensure sufficient contact time between gas and solid and we have to use two bubbling beds for each reaction to ensure sufficient contact time. In this case, additional riser must be installed for solid circulation. Consequently, conventional two-interconnected fluidized bed systems are very complex, large, and difficult to operate. To solve these problems, a novel two-interconnected fluidized bed system has been developed. This system has two bubbling beds, solid injection nozzles, solid conveying lines, and downcomers. In this study, effects of operating variables on solid circulation rate, gas leakage between two beds have been investigated in a cold mode two-interconnected fluidized bed system. Moreover, long-term operation of continuous solid circulation up to 60 hours has been performed to check feasibility of stable operation.
Abstract: The purpose of this paper is to contribute to the body
of knowledge in the area of management accounting, particularly
performance measurement systems within the BSC framework, by
investigating empirically the extent of multiple performance
measures usage and their effects on the financial performance of
Jordanian banks in the branches level. Nevertheless, the result of this
study shows that the non-financial measures usages, particularly,
customer oriented indicators and product/ service oriented indicators,
appears to be important as it enhances firm performance.
Remarkably, the findings reveal that there is positive relationship
between the usages of multiple performance measures via overall
BSC measures and financial performance in the branches level.
Abstract: COPD is characterized by loss of elastic fibers from
small airways and alveolar walls, with the decrease in elastin
increasing with disease severity. It is unclear why there is a lack of
repair of elastic fibers. We have examined fibroblasts cultured from
lung tissue from normal and COPD subjects to determine if the
secretory profile explains lack of tissue repair. In this study,
fibroblasts were cultured from lung parenchyma of bronchial
carcinoma patients with varying degrees of COPD; controls
(non-COPD, n=5), mild COPD (GOLD 1, n=5) and moderate-severe
COPD (GOLD 2-3, n=12). Measurements were made of proliferation,
senescence-associated beta-galactosidase-1, mRNA expression of
IL-6, IL-8, MMP-1, tropoelastin and versican, and protein levels for
IL-6, IL-8, PGE2, tropoelastin, insoluble elastin, and versican. It was
found that GOLD 2-3 fibroblasts proliferated more slowly (p
Abstract: Measurement of the quality of image compression is important for image processing application. In this paper, we propose an objective image quality assessment to measure the quality of gray scale compressed image, which is correlation well with subjective quality measurement (MOS) and least time taken. The new objective image quality measurement is developed from a few fundamental of objective measurements to evaluate the compressed image quality based on JPEG and JPEG2000. The reliability between each fundamental objective measurement and subjective measurement (MOS) is found. From the experimental results, we found that the Maximum Difference measurement (MD) and a new proposed measurement, Structural Content Laplacian Mean Square Error (SCLMSE), are the suitable measurements that can be used to evaluate the quality of JPEG200 and JPEG compressed image, respectively. In addition, MD and SCLMSE measurements are scaled to make them equivalent to MOS, given the rate of compressed image quality from 1 to 5 (unacceptable to excellent quality).
Abstract: In this paper authors presented the research of textile electroconductive materials, which can be used to construction
sensory textronic shirt to breath frequency measurement.
The full paper also will present results of measurements carried
out on unique measurement stands.
Abstract: The paper depicts air velocity values, reproduced by laser Doppler anemometer (LDA) and ultrasonic anemometer (UA), relations with calculated ones from flow rate measurements using the gas meter which calibration uncertainty is ± (0.15 – 0.30) %. Investigation had been performed in channel installed in aerodynamical facility used as a part of national standard of air velocity. Relations defined in a research let us confirm the LDA and UA for air velocity reproduction to be the most advantageous measures. The results affirm ultrasonic anemometer to be reliable and favourable instrument for measurement of mean velocity or control of velocity stability in the velocity range of 0.05 m/s – 10 (15) m/s when the LDA used. The main aim of this research is to investigate low velocity regularities, starting from 0.05 m/s, including region of turbulent, laminar and transitional air flows. Theoretical and experimental results and brief analysis of it are given in the paper. Maximum and mean velocity relations for transitional air flow having unique distribution are represented. Transitional flow having distinctive and different from laminar and turbulent flow characteristics experimentally have not yet been analysed.
Abstract: This paper may be considered as combination of both pervasive computing and Differential GPS (global positioning satellite) which relates to control automatic traffic signals in such a
way as to pre-empt normal signal operation and permit lifesaving vehicles. Before knowing the arrival of the lifesaving vehicles from
the signal there is a chance of clearing the traffic. Traffic signal
preemption system includes a vehicle equipped with onboard computer system capable of capturing diagnostic information and
estimated location of the lifesaving vehicle using the information provided by GPS receiver connected to the onboard computer system
and transmitting the information-s using a wireless transmitter via a
wireless network. The fleet management system connected to a
wireless receiver is capable of receiving the information transmitted
by the lifesaving vehicle .A computer is also located at the
intersection uses corrected vehicle position, speed & direction
measurements, in conjunction with previously recorded data defining
approach routes to the intersection, to determine the optimum time to
switch a traffic light controller to preemption mode so that lifesaving
vehicles can pass safely. In case when the ambulance need to take a
“U" turn in a heavy traffic area we suggest a solution. Now we are
going to make use of computerized median which uses LINKED
BLOCKS (removable) to solve the above problem.