Abstract: This paper presents a fuzzy control system for a three degree of freedom (3-DOF) stabilized platform with explicit decoupling scheme. The system under consideration is a system with strong interactions between three channels. By using the concept of decentralized control, a control structure is developed that is composed of three control loops, each of which is associated with a single-variable fuzzy controller and a decoupling unit. Takagi-Sugeno (TS) fuzzy control algorithm is used to implement the fuzzy controller. The decoupling units design is based on the adaptive theory reasoning. Simulation tests were established using Simulink of Matlab. The obtained results have demonstrated the feasibility and effectiveness of the proposed approach. Simulation results are represented in this paper.
Abstract: Climate change and environmental pressures are
major international issues nowadays. It is time when governments,
businesses and consumers have to respond through more
environmentally friendly and aware practices, products and policies.
This is the prime time to develop alternative sustainable construction
materials, reduce greenhouse gas emissions, save energy, look to
renewable energy sources and recycled materials, and reduce waste.
The utilization of waste materials (slag, fly ash, glass beads, plastic
and so on) in concrete manufacturing is significant due to its
engineering, financial, environmental and ecological benefits. Thus,
utilization of waste materials in concrete production is very much
helpful to reach the goal of the sustainable construction. Therefore,
this study intends to use glass beads in concrete production.
The paper reports on the performance of 9 different concrete
mixes containing different ratios of glass crushed to 5 mm - 20 mm
maximum size and glass marble of 20 mm size as coarse aggregate.
Ordinary Portland cement type 1 and fine sand less than 0.5 mm were
used to produce standard concrete cylinders. Compressive strength
tests were carried out on concrete specimens at various ages. Test
results indicated that the mix having the balanced ratio of glass beads
and round marbles possess maximum compressive strength which is
3889 psi, as glass beads perform better in bond formation but have
lower strength, on the other hand marbles are strong in themselves
but not good in bonding. These mixes were prepared following a
specific W/C and aggregate ratio; more strength can be expected to
achieve from different W/C, aggregate ratios, adding admixtures like
strength increasing agents, ASR inhibitor agents etc.
Abstract: Asphalt surfaces are exposed to various weather
conditions and dynamic loading caused by passing trucks and
vehicles. In such situations, asphalt cement shows so different
rheological-mechanical behavior. If asphalt cement isn-t compatible
enough, asphalt layer will be damaged immediately and expensive
repairing procedures should be performed then. To overcome this
problem, researchers study on mechanical improved asphalt cement.
In this study, bentonite was used in order to modify bitumen
characteristics and the modified bitumen's characteristics were
investigated by asphalt cement tests. Then, the optimal bitumen
content in various compounds was determined and asphalt samples
with different contents of additives were prepared and tested. Results
show using this kind of additive not only has caused improvement in
bitumen mechanical properties, but also improvement in Marshall
Parameters was achieved.
Abstract: The roll center is one of the key parameters for designing a suspension. Several driving characteristics are affected significantly by the migration of the roll center during the suspension-s motion. The strut/SLA (strut/short-long-arm) suspension, which is widely used in production cars, combines the space-saving characteristics of a MacPherson strut suspension with some of the preferred handling characteristics of an SLA suspension. In this study, a front strut/SLA suspension is modeled by ADAMS/Car software. Kinematic roll analysis is then employed to investigate how the rolling characteristics change under the wheel travel and steering input. The related parameters, including the roll center height, roll camber gain, toe change, scrub radius and wheel track width change, are analyzed and discussed. It is found that the strut/SLA suspension clearly has a higher roll center than strut and SLA suspensions do. The variations in the roll center height under roll analysis are very different as the wheel travel displacement and steering angle are added. The results of the roll camber gain, scrub radius and wheel track width change are considered satisfactory. However, the toe change is too large and needs fine-tuning through a sensitivity analysis.
Abstract: Classification of electroencephalogram (EEG) signals
extracted during mental tasks is a technique that is actively pursued
for Brain Computer Interfaces (BCI) designs. In this paper, we
compared the classification performances of univariateautoregressive
(AR) and multivariate autoregressive (MAR) models
for representing EEG signals that were extracted during different
mental tasks. Multilayer Perceptron (MLP) neural network (NN)
trained by the backpropagation (BP) algorithm was used to classify
these features into the different categories representing the mental
tasks. Classification performances were also compared across
different mental task combinations and 2 sets of hidden units (HU): 2
to 10 HU in steps of 2 and 20 to 100 HU in steps of 20. Five different
mental tasks from 4 subjects were used in the experimental study and
combinations of 2 different mental tasks were studied for each
subject. Three different feature extraction methods with 6th order
were used to extract features from these EEG signals: AR
coefficients computed with Burg-s algorithm (ARBG), AR
coefficients computed with stepwise least square algorithm (ARLS)
and MAR coefficients computed with stepwise least square
algorithm. The best results were obtained with 20 to 100 HU using
ARBG. It is concluded that i) it is important to choose the suitable
mental tasks for different individuals for a successful BCI design, ii)
higher HU are more suitable and iii) ARBG is the most suitable
feature extraction method.
Abstract: Manufacturing companies are facing a broad variety
of challenges caused by a dynamic production environment. To
succeed in such an environment, it is crucial to minimize the loss of
time required to trigger the adaptation process of a company-s
production structures. This paper presents an approach for the
continuous monitoring of production structures by neurologic
principles. It enhances classical monitoring concepts, which are
principally focused on reactive strategies, and enables companies to
act proactively. Thereby, strategic aspects regarding the
harmonization of certain life cycles are integrated into the decision
making process for triggering the reconfiguration process of the
production structure.
Abstract: In order to be able to automatically differentiate
between two modes of permanent flow of a liquid simulating blood,
it was imperative to put together a data bank. Thus, the acquisition of
the various amplitude spectra of the Doppler signal of this liquid in
laminar flow and other spectra in turbulent flow enabled us to
establish an automatic difference between the two modes. According
to the number of parameters and their nature, a comparative study
allowed us to choose the best classifier.
Abstract: As we know, most differential equations concerning
physical phenomenon could not be solved by analytical method. Even if we use Series Method, some times we need an appropriate change of variable, and even when we can, their closed form solution may be
so complicated that using it to obtain an image or to examine the structure of the system is impossible. For example, if we consider Schrodinger equation, i.e.,
We come to a three-term recursion relations, which work with it takes, at least, a little bit time to get a series solution[6]. For this
reason we use a change of variable such as or when we consider the orbital angular momentum[1], it will be
necessary to solve. As we can observe, working with this equation is tedious. In this paper, after introducing Clenshaw method, which is a kind of Spectral method, we try to solve some of such equations.
Abstract: The aim of the paper work is to investigate and predict
the static performance of journal bearing in turbulent flow condition
considering micropolar lubrication. The Reynolds equation has been
modified considering turbulent micropolar lubrication and is solved
for steady state operations. The Constantinescu-s turbulence model is
adopted using the coefficients. The analysis has been done for a
parallel and inertia less flow. Load capacity and friction factor have
been evaluated for various operating parameters.
Abstract: According to celebrated Hurwitz theorem, there exists
four division algebras consisting of R (real numbers), C (complex
numbers), H (quaternions) and O (octonions). Keeping in view
the utility of octonion variable we have tried to extend the three
dimensional vector analysis to seven dimensional one. Starting with
the scalar and vector product in seven dimensions, we have redefined
the gradient, divergence and curl in seven dimension. It is shown
that the identity n(n - 1)(n - 3)(n - 7) = 0 is satisfied only
for 0, 1, 3 and 7 dimensional vectors. We have tried to write all
the vector inequalities and formulas in terms of seven dimensions
and it is shown that same formulas loose their meaning in seven
dimensions due to non-associativity of octonions. The vector formulas
are retained only if we put certain restrictions on octonions and split
octonions.
Abstract: Biplot can be used to evaluate cultivars for their oil
percent potential and stability and to evaluate trial sites for their
discriminating ability and representativeness. Multi-environmental
trial (MET) data for oil percent of 10 open pollinating sunflower
cultivars were analyzed to investigate the genotype-environment
interactions. The genotypes were evaluated in four locations with
different climatic conditions in Iran in 2010. In each location, a
Randomized Complete Block design with four replications was used.
According to both mean and stability, Zaria, Master and R453, had
highest performances among all cultivars. The graphical analysis
identified best cultivar for each environment. Cultivars Berezans and
Record performed best in Khoy and Islamabad. Zaria and R453 were
the best genotypes in Sari and Karaj followed by Master and Favorit.
The GGE bi-plot indicated two mega-environments, group one
contained Karaj, Khoy and Islamabad and the second group
contained Sari. The best discriminating location was Karaj followed
with Khoy, Islamabad and Sari. The best representative genotypes
were Zaria, R453, Master and Favorit. Ranking of ten cultivars based
their oil percent was as Zaria > R453 ≈ Master ≈ Favorit > Record ≈
Berezans > Sor > Lakumka > Bulg3 > Bulg5.
Abstract: Since the presentation of the backpropagation algorithm, a vast variety of improvements of the technique for training a feed forward neural networks have been proposed. This article focuses on two classes of acceleration techniques, one is known as Local Adaptive Techniques that are based on weightspecific only, such as the temporal behavior of the partial derivative of the current weight. The other, known as Dynamic Adaptation Methods, which dynamically adapts the momentum factors, α, and learning rate, η, with respect to the iteration number or gradient. Some of most popular learning algorithms are described. These techniques have been implemented and tested on several problems and measured in terms of gradient and error function evaluation, and percentage of success. Numerical evidence shows that these techniques improve the convergence of the Backpropagation algorithm.
Abstract: In a metal forming process, the friction between the
material and the tools influences the process by modifying the stress
distribution of the workpiece. This frictional behaviour is often taken
into account by using a constant coefficient of friction in the finite
element simulations of sheet metal forming processes. However,
friction coefficient varies in time and space with many parameters.
The Stribeck friction model is investigated in this study to predict
springback behaviour of AA6061-T4 sheets during V-bending
process. The coefficient of friction in Stribeck curve depends on
sliding velocity and contact pressure. The plane-strain bending
process is simulated in ABAQUS/Standard. We compared the
computed punch load-stroke curves and springback related to the
constant coefficient of friction with the defined friction model. The
results clearly showed that the new friction model provides better
agreement between experiments and results of numerical simulations.
The influence of friction models on stress distribution in the
workpiece is also studied numerically
Abstract: An attempt has been made to develop a
seminumerical model to study temperature variations in dermal
layers of human limbs. The model has been developed for two
dimensional steady state case. The human limb has been assumed to
have elliptical cross section. The dermal region has been divided
into three natural layers namely epidermis, dermis and subdermal
tissues. The model incorporates the effect of important physiological
parameters like blood mass flow rate, metabolic heat generation, and
thermal conductivity of the tissues. The outer surface of the limb is
exposed to the environment and it is assumed that heat loss takes
place at the outer surface by conduction, convection, radiation, and
evaporation. The temperature of inner core of the limb also varies at
the lower atmospheric temperature. Appropriate boundary conditions
have been framed based on the physical conditions of the problem.
Cubic splines approach has been employed along radial direction and
Fourier series along angular direction to obtain the solution. The
numerical results have been computed for different values of
eccentricity resembling with the elliptic cross section of the human
limbs. The numerical results have been used to obtain the
temperature profile and to study the relationships among the various
physiological parameters.
Abstract: IFP Group Technology “Sulfrex process" was used in
Iran-s South Pars Gas Complex Refineries for removing sulfur
compounds such as mercaptans, carbonyl sulfide and hydrogen
sulfide, which uses sulfonated cobalt phthalocyanine dispersed in
alkaline solution as catalyst. In this technology, catalyst and alkaline
solution were used circularly. However the stability of catalyst due to
effect of some parameters would reduce with the running of the unit
and therefore sweetening efficiency would be decreased. Hence, the
aim of this research is study the factors effecting on the stability of
catalyst.
Abstract: Accurate demand forecasting is one of the most key
issues in inventory management of spare parts. The problem of
modeling future consumption becomes especially difficult for lumpy
patterns, which characterized by intervals in which there is no
demand and, periods with actual demand occurrences with large
variation in demand levels. However, many of the forecasting
methods may perform poorly when demand for an item is lumpy.
In this study based on the characteristic of lumpy demand patterns
of spare parts a hybrid forecasting approach has been developed,
which use a multi-layered perceptron neural network and a
traditional recursive method for forecasting future demands. In the
described approach the multi-layered perceptron are adapted to
forecast occurrences of non-zero demands, and then a conventional
recursive method is used to estimate the quantity of non-zero
demands. In order to evaluate the performance of the proposed
approach, their forecasts were compared to those obtained by using
Syntetos & Boylan approximation, recently employed multi-layered
perceptron neural network, generalized regression neural network
and elman recurrent neural network in this area. The models were
applied to forecast future demand of spare parts of Arak
Petrochemical Company in Iran, using 30 types of real data sets. The
results indicate that the forecasts obtained by using our proposed
mode are superior to those obtained by using other methods.
Abstract: Gas turbine systems with wet compression have a
potential for future power generation, since they can offer a high
efficiency and a high specific power with a relatively low cost. In this
study influence of ambient condition on the performance of the wet
compression process is investigated with a non-equilibrium analytical
modeling based on droplet evaporation. Transient behaviors of droplet
diameter and temperature of mixed air are investigated for various
ambient temperatures. Special attention is paid for the effects of
ambient temperature, pressure ratio, and water injection ratios on the
important wet compression variables including compressor outlet
temperature and compression work. Parametric studies show that
downing of the ambient temperature leads to lower compressor outlet
temperature and consequently lower consumption of compression
work even in wet compression processes.
Abstract: In the present analysis an unsteady laminar
forced convection water boundary layer flow is considered.
The fluid properties such as viscosity and Prandtl number are
taken as variables such that those are inversely proportional to
temperature. By using quasi-linearization technique the nonlinear
coupled partial differential equations are linearized and
the numerical solutions are obtained by using implicit finite
difference scheme with the appropriate selection of step sizes.
Non-similar solutions have been obtained from the starting
point of the stream-wise coordinate to the point where skin
friction value vanishes. The effect non-uniform mass transfer
along the surface of the cylinder through slot is studied on the
skin friction and heat transfer coefficients.
Abstract: This paper deals with an adaptive multiuser detector for direct sequence code division multiple-access (DS-CDMA) systems. A modified receiver, precombinig LMMSE is considered under time varying channel environment. Detector updating is performed with two criterions, mean square estimation (MSE) and MOE optimization technique. The adaptive implementation issues of these two schemes are quite different. MSE criterion updates the filter weights by minimizing error between data vector and adaptive vector. MOE criterion together with canonical representation of the detector results in a constrained optimization problem. Even though the canonical representation is very complicated under time varying channels, it is analyzed with assumption of average power profile of multipath replicas of user of interest. The performance of both schemes is studied for practical SNR conditions. Results show that for poor SNR, MSE precombining LMMSE is better than the blind precombining LMMSE but for greater SNR, MOE scheme outperforms with better result.
Abstract: In this article, models based on quantitative analysis,
physical geometry and regression analysis are established, by using
analytic hierarchy process analysis, fuzzy cluster analysis, fuzzy
photographic and data fitting. The reasons of various leaf shapes
among different species and the differences between the leaf shapes on
same tree have been solved by using software, such as Eviews, VB and
Matlab. We also successfully estimate the leaf mass of a tree and the
correlation with the tree profile.