Abstract: In order to provide accurate heart rate variability
indices of sympathetic and parasympathetic activity, the low
frequency and high frequency components of an RR heart rate signal
must be adequately separated. This is not always possible by just
applying spectral analysis, as power from the high and low frequency
components often leak into their adjacent bands. Furthermore,
without the respiratory spectra it is not obvious that the low
frequency component is not another respiratory component, which
can appear in the lower band. This paper describes an adaptive filter,
which aids the separation of the low frequency sympathetic and high
frequency parasympathetic components from an ECG R-R interval
signal, enabling the attainment of more accurate heart rate variability
measures. The algorithm is applied to simulated signals and heart rate
and respiratory signals acquired from an ambulatory monitor
incorporating single lead ECG and inductive plethysmography
sensors embedded in a garment. The results show an improvement
over standard heart rate variability spectral measurements.
Abstract: This paper describes a 2.4 GHz passive switch mixer
and a 5/2.5 GHz voltage-controlled negative Gm oscillator (VCO)
with an inversion-mode MOS varactor. Both circuits are implemented
using a 1P8M 0.13 μm process. The switch mixer has an input
referred 1 dB compression point of -3.89 dBm and a conversion
gain of -0.96 dB when the local oscillator power is +2.5 dBm.
The VCO consumes only 1.75 mW, while drawing 1.45 mA from a
1.2 V supply voltage. In order to reduce the passives size, the VCO
natural oscillation frequency is 5 GHz. A clocked CMOS divideby-
two circuit is used for frequency division and quadrature phase
generation. The VCO has a -109 dBc/Hz phase noise at 1 MHz
frequency offset and a 2.35-2.5 GHz tuning range (after the frequency
division), thus complying with ZigBee requirements.
Abstract: Different techniques for estimating seasonal water
use from soil profile water depletion frequently do not account for
flux below the root zone. Shallow water table contribution to supply
crop water use may be important in arid and semi-arid regions.
Development of predictive root uptake models, under influence of
shallow water table makes it possible for planners to incorporate
interaction between water table and root zone into design of irrigation
projects. A model for obtaining soil moisture depletion from root
zone and water movement below it is discussed with the objective to
determine impact of shallow water table on seasonal moisture
depletion patterns under water table depth variation, up to the bottom
of root zone. The role of different boundary conditions has also been
considered. Three crops: Wheat (Triticum aestivum), Corn (Zea
mays) and Potato (Solanum tuberosum), common in arid & semi-arid
regions, are chosen for the study. Using experimentally obtained soil
moisture depletion values for potential soil moisture conditions,
moisture depletion patterns using a non linear root uptake model have
been obtained for different water table depths. Comparative analysis
of the moisture depletion patterns under these conditions show a wide
difference in percent depletion from different layers of root zone
particularly top and bottom layers with middle layers showing
insignificant variation in moisture depletion values. Moisture
depletion in top layer, when the water table rises to root zone
increases by 19.7%, 22.9% & 28.2%, whereas decrease in bottom
layer is 68.8%, 61.6% & 64.9% in case of wheat, corn & potato
respectively. The paper also discusses the causes and consequences
of increase in moisture depletion from top layers and exceptionally
high reduction in bottom layer, and the possible remedies for the
same. The numerical model developed for the study can be used to
help formulating irrigation strategies for areas where shallow
groundwater of questionable quality is an option for crop production.
Abstract: From the perspective of industrial structure
coordination and based on an explicit definition for the connotation of
industrial structure coordination, the synergetic coefficients are used
to measure the coordination degree between three industries' input
structure and output structure, and then the efficacy function method is
employed to comprehensively evaluate the level of China-s industrial
structure optimization. It is showed that Chinese industrial structure
presented a "v-shaped" variation tendency between 1996 and 2008,
and its industrial structure adjustment got obvious achievements after
2003, with the industrial structure optimization level increasing
continuously. However in 2009, the level of China-s industrial
structure optimization declined sharply due to the decreasing
contribution degree of value added structure and energy structure
coordination and the lower coordination degree of value added
structure and capital structure.
Abstract: Three-phase induction machines are today a standard
for industrial electrical drives. Cost, reliability, robustness and maintenance free operation are among the reasons these machines are
replacing dc drive systems. The development of power electronics
and signal processing systems has eliminated one of the greatest
disadvantages of such ac systems, which is the issue of control. With
modern techniques of field oriented vector control, the task of
variable speed control of induction machines is no longer a
disadvantage. The need to increase system performance, particularly
when facing limits on the power ratings of power supplies and
semiconductors, motivates the use of phase number other than three,
In this paper a novel scheme of connecting two, three phase
induction motors in parallel fed by two inverters; viz. VSI and CSI
and their vector control is presented.
Abstract: Efficient and safe plant operation can only be
achieved if the operators are able to monitor all key process
parameters. Instrumentation is used to measure many process
variables, like temperatures, pressures, flow rates, compositions or
other product properties. Therefore Performance monitoring is a
suitable tool for operators. In this paper, we integrate rigorous
simulation model, data reconciliation and parameter estimation to
monitor process equipments and determine key performance
indicator (KPI) of them. The applied method here has been
implemented in two case studies.
Abstract: Solution of some practical problems is reduced to the
solution of the integro-differential equations. But for the numerical
solution of such equations basically quadrature methods or its
combination with multistep or one-step methods are used. The
quadrature methods basically is applied to calculation of the integral
participating in right hand side of integro-differential equations. As
this integral is of Volterra type, it is obvious that at replacement with
its integrated sum the upper limit of the sum depends on a current
point in which values of the integral are defined. Thus we receive the
integrated sum with variable boundary, to work with is hardly.
Therefore multistep method with the constant coefficients, which is
free from noted lack and gives the way for finding it-s coefficients is
present.
Abstract: A cross sectional study design and standard
microbiological procedures were used to determine the prevalence
and antimicrobial susceptibility patterns of Escherichia coli,
Salmonella enterica serovar typhimurium and Vibrio cholerae O1
isolated from water and two fish species Rastrineobola argentea and
Oreochromis niloticus collected from fish landing beaches and
markets in the Lake Victoria Basin of western Kenya. Out of 162
samples analyzed, 133 (82.1%) were contaminated, with S.
typhimurium as the most prevalent (49.6%), followed by E. coli
(46.6%), and lastly V. cholerae (2.8%). All the bacteria isolates were
sensitive to ciprofloxacin. E. coli isolates were resistant to ampicillin,
tetracycline, cotrimoxazole, chloramphenical and gentamicin while
S. typhimurium isolates exhibited resistance to ampicillin,
tetracycline, and cotrimoxazole. The V. cholerae O1 isolates were
resistant to tetracycline and ampicillin. The high prevalence of drug
resistant enteric bacteria in water and fish from the study region
needs public health intervention from the local government.
Abstract: The purpose of this paper is to explore the relationship
between the customers- issues in company corporate governance and
the financial performance. At the beginning theoretical background
consisting stakeholder theory and corporate governance is presented.
On this theoretical background, the empirical research is built,
collecting data of 60 Czech joint stock companies- boards
considering their relationships with customers. Correlation analysis
and multivariate regression analysis were employed to test the sample
on two hypotheses. The weak positive correlation between
stakeholder approach and the company size was identified. But both
hypotheses were not supported, because there was no significant
relation of independent variables to financial performance.
Abstract: This work presents a recursive identification algorithm. This algorithm relates to the identification of closed loop system with Variable Structure Controller. The approach suggested includes two stages. In the first stage a genetic algorithm is used to obtain the parameters of switching function which gives a control signal rich in commutations (i.e. a control signal whose spectral characteristics are closest possible to those of a white noise signal). The second stage consists in the identification of the system parameters by the instrumental variable method and using the optimal switching function parameters obtained with the genetic algorithm. In order to test the validity of this algorithm a simulation example is presented.
Abstract: The studies concerned an effect of six variants of ion
exchange substrate (nutrient carriers with a different potential impact
on pH of soil solution) on vegetation of orchard grass during two
different periods (42 and 84 days). In the pot experiment plants were
grown on sand (model of degraded soil) and six mixtures of sand and
2% (v/v) additions of particular variants of ion exchange substrate
(with pH ranged from 5.5 to 8.0). The study results showed that the
addition of the substrate at pH=6.5 caused the highest increase in
plant yield after shorter vegetation period whereas the addition of the
substrate at pH=5.5 increased dry stem and root biomass of orchard
grass after longer vegetation period. Thus, the ion exchange substrate
at pH=6.5 can be recommended for restoration of exhausted soils
when shorter vegetation period is planned; the ion exchange substrate
at pH=5.5 can be used for the same purpose when longer periods of
vegetative growth are considered.
Abstract: The main issue of interest here is whether individuals
who differ in arithmetical reasoning ability and levels of imagery ability display different brain activity during the conduct of mental
arithmetical reasoning tasks. This was a case study of four
participants who represented four extreme combinations of Maths –Imagery abilities: ie., low-low, high-high, high-low, low-high respectively. As the Ps performed a series of 60 arithmetical reasoning tasks, 128-channel EEG recordings were taken and the
pre-response interval subsequently analysed using EGI GeosourceTM
software. The P who was high in both imagery and maths ability
showed peak activity prior to response in BA7 (superior parietal cortex) but other Ps did not show peak activity in this region. The
results are considered in terms of the diverse routes that may be employed by individuals during the conduct of arithmetical reasoning
tasks and the possible implications of this for mathematics education.
Abstract: This paper proposes a new technique based on nonlinear Minmax Detector Based (MDB) filter for image restoration. The aim of image enhancement is to reconstruct the true image from the corrupted image. The process of image acquisition frequently leads to degradation and the quality of the digitized image becomes inferior to the original image. Image degradation can be due to the addition of different types of noise in the original image. Image noise can be modeled of many types and impulse noise is one of them. Impulse noise generates pixels with gray value not consistent with their local neighborhood. It appears as a sprinkle of both light and dark or only light spots in the image. Filtering is a technique for enhancing the image. Linear filter is the filtering in which the value of an output pixel is a linear combination of neighborhood values, which can produce blur in the image. Thus a variety of smoothing techniques have been developed that are non linear. Median filter is the one of the most popular non-linear filter. When considering a small neighborhood it is highly efficient but for large window and in case of high noise it gives rise to more blurring to image. The Centre Weighted Mean (CWM) filter has got a better average performance over the median filter. However the original pixel corrupted and noise reduction is substantial under high noise condition. Hence this technique has also blurring affect on the image. To illustrate the superiority of the proposed approach, the proposed new scheme has been simulated along with the standard ones and various restored performance measures have been compared.
Abstract: This paper present the study carried out of accident
analysis, black spot study and to develop accident predictive models
based on the data collected at rural roadway, Federal Route 50 (F050)
Malaysia. The road accident trends and black spot ranking were
established on the F050. The development of the accident prediction
model will concentrate in Parit Raja area from KM 19 to KM 23.
Multiple non-linear regression method was used to relate the discrete
accident data with the road and traffic flow explanatory variable. The
dependent variable was modeled as the number of crashes namely
accident point weighting, however accident point weighting have
rarely been account in the road accident prediction Models. The result
show that, the existing number of major access points, without traffic
light, rise in speed, increasing number of Annual Average Daily
Traffic (AADT), growing number of motorcycle and motorcar and
reducing the time gap are the potential contributors of increment
accident rates on multiple rural roadway.
Abstract: In Virtual organization, Knowledge Discovery (KD)
service contains distributed data resources and computing grid nodes.
Computational grid is integrated with data grid to form Knowledge
Grid, which implements Apriori algorithm for mining association
rule on grid network. This paper describes development of parallel
and distributed version of Apriori algorithm on Globus Toolkit using
Message Passing Interface extended with Grid Services (MPICHG2).
The creation of Knowledge Grid on top of data and
computational grid is to support decision making in real time
applications. In this paper, the case study describes design and
implementation of local and global mining of frequent item sets. The
experiments were conducted on different configurations of grid
network and computation time was recorded for each operation. We
analyzed our result with various grid configurations and it shows
speedup of computation time is almost superlinear.
Abstract: The Wind Turbine Modeling in Wind Energy Conversion System (WECS) using Doubly-Fed Induction Generator (DFIG) PI Controller based design is presented. To study about the variable wind speed. The PI controller performs responding to the dynamic performance. The objective is to study the characteristic of wind turbine and finding the optimum wind speed suitable for wind turbine performance. This system will allow the specification setting (2.5MW). The output active power also corresponding same the input is given. And the reactive power produced by the wind turbine is regulated at 0 Mvar. Variable wind speed is optimum for drive train performance at 12.5 m/s (at maximum power coefficient point) from the simulation of DFIG by Simulink is described.
Abstract: Signature represents an individual characteristic of a
person which can be used for his / her validation. For such application
proper modeling is essential. Here we propose an offline signature
recognition and verification scheme which is based on extraction of
several features including one hybrid set from the input signature
and compare them with the already trained forms. Feature points
are classified using statistical parameters like mean and variance.
The scanned signature is normalized in slant using a very simple
algorithm with an intention to make the system robust which is
found to be very helpful. The slant correction is further aided by the
use of an Artificial Neural Network (ANN). The suggested scheme
discriminates between originals and forged signatures from simple
and random forgeries. The primary objective is to reduce the two
crucial parameters-False Acceptance Rate (FAR) and False Rejection
Rate (FRR) with lesser training time with an intension to make the
system dynamic using a cluster of ANNs forming a multiple classifier
system.
Abstract: In this paper, we study the multi-scenario knapsack problem, a variant of the well-known NP-Hard single knapsack problem. We investigate the use of an adaptive algorithm for solving heuristically the problem. The used method combines two complementary phases: a size reduction phase and a dynamic 2- opt procedure one. First, the reduction phase applies a polynomial reduction strategy; that is used for reducing the size problem. Second, the adaptive search procedure is applied in order to attain a feasible solution Finally, the performances of two versions of the proposed algorithm are evaluated on a set of randomly generated instances.
Abstract: Within dental-guided surgery, there has been a lack
of analytical methods for optimizing the treatment of the
rehabilitation concepts regarding geometrical variation. The purpose
of this study is to find the source of the greatest geometrical variation
contributor and sensitivity contributor with the help of virtual
variation simulation of a dental drill- and implant-guided surgery
process using a methodical approach. It is believed that lower
geometrical variation will lead to better patient security and higher
quality of dental drill- and implant-guided surgeries. It was found
that the origin of the greatest contributor to the most variation, and
hence where the foci should be set, in order to minimize geometrical
variation was in the assembly category (surgery). This was also the
category that was the most sensitive for geometrical variation.
Abstract: Quality evaluation of urban environment is an integral
part of efficient urban environment planning and management. The
development of fuzzy set theory (FST) and the introduction of FST
to the urban study field attempts to incorporate the gradual variation
and avoid loss of information. Urban environmental quality
assessment pertain to interpretation and forecast of the urban
environmental quality according to the national regulation about the
permitted content of contamination for the sake of protecting human
health and subsistence environment . A strategic motor vehicle
control strategy has to be proposed to mitigate the air pollution in the
city. There is no well defined guideline for the assessment of urban
air pollution and no systematic study has been reported so far for
Indian cities. The methodology adopted may be useful in similar
cities of India. Remote sensing & GIS can play significant role in
mapping air pollution.