Abstract: The present work attempts to investigate the
combustion, performance and emission characteristics of an existing
single-cylinder four-stroke compression-ignition engine operated in
dual-fuel mode with hydrogen as an alternative fuel. Environmental
concerns and limited amount of petroleum fuels have caused interests
in the development of alternative fuels like hydrogen for internal
combustion (IC) engines. In this experimental investigation, a diesel
engine is made to run using hydrogen in dual fuel mode with diesel,
where hydrogen is introduced into the intake manifold using an LPGCNG
injector and pilot diesel is injected using diesel injectors. A
Timed Manifold Injection (TMI) system has been developed to vary
the injection strategies. The optimized timing for the injection of
hydrogen was 10^0 CA after top dead center (ATDC). From the study
it was observed that with increasing hydrogen rate, enhancement in
brake thermal efficiency (BTHE) of the engine has been observed
with reduction in brake specific energy consumption (BSEC).
Furthermore, Soot contents decrease with an increase in indicated
specific NOx emissions with the enhancement of hydrogen flow rate.
Abstract: We address a new integer frequency offset (IFO)
estimation scheme with an aid of a pilot for orthogonal frequency
division multiplexing systems. After correlating each continual pilot
with a predetermined scattered pilot, the correlation value is again
correlated to alleviate the influence of the timing offset. From
numerical results, it is demonstrated that the influence of the timing
offset on the IFO estimation is significantly decreased.
Abstract: This work proposes a data-driven multiscale based
quantitative measures to reveal the underlying complexity of
electroencephalogram (EEG), applying to a rodent model of
hypoxic-ischemic brain injury and recovery. Motivated by that real
EEG recording is nonlinear and non-stationary over different
frequencies or scales, there is a need of more suitable approach over
the conventional single scale based tools for analyzing the EEG data.
Here, we present a new framework of complexity measures
considering changing dynamics over multiple oscillatory scales. The
proposed multiscale complexity is obtained by calculating entropies of
the probability distributions of the intrinsic mode functions extracted
by the empirical mode decomposition (EMD) of EEG. To quantify
EEG recording of a rat model of hypoxic-ischemic brain injury
following cardiac arrest, the multiscale version of Tsallis entropy is
examined. To validate the proposed complexity measure, actual EEG
recordings from rats (n=9) experiencing 7 min cardiac arrest followed
by resuscitation were analyzed. Experimental results demonstrate that
the use of the multiscale Tsallis entropy leads to better discrimination
of the injury levels and improved correlations with the neurological
deficit evaluation after 72 hours after cardiac arrest, thus suggesting an
effective metric as a prognostic tool.
Abstract: The thermal performance of a solar water heating with
1.00 m2 flat plate collectors in Cascavel - PR, is which presented in
this article, paper presents the solution to leverage the marketing of
solar heating systems through detailed constituent materials of the
solar collector studies, these abundant materials in construction, such
as expanded polyethylene, PVC, aluminum and glass tubes, mixing
them with new materials to minimize loss of efficiency while
decreasing its cost. The system was tested during months and the
collector obtained maximum recorded temperature of outlet fluid of
55°C, while the maximum temperature of the water at the bottom of
the hot water tank was 35°C. The average daily energy collected was
19.6 MJ/d; the energy supplied by the solar plate was 16.2 MJ/d; the
loss in the feed pipe was 3.2 MJ/d; the solar fraction was 32.2%, the
efficiency of the collector was 45.6% and the efficiency of the system
was 37.8%.
Abstract: By textile science incorporating with electronic
industry, developed textile products start to take part in different
areas such as industry, military, space, medical etc. for health,
protection, defense, communication and automation. Electronic
textiles (e-textiles) are fabrics that contain electronics and
interconnections with them. In this study, two types of base yarns
(cotton and acrylic) and three types of conductive steel yarns with
different linear resistance values (14Ω/m, 30Ω/m, 70Ω/m) were used
to investigate the effect of base yarn type and linear resistance of
conductive yarns on thermal behavior of e-textile structures. Thermal
behavior of samples was examined by thermal camera.
Abstract: This paper presents a study the effect of nose radius
(Rz-mm) on cutting force components and temperatures during the
machining simulation in an orthogonal cutting process for titanium
alloy (Ti-6Al-4V). The cutting process was performed at various
nose radiuses (Rz-mm) while the depth of cut (d-mm), feed rate (fmm/
tooth) and cutting speed (vc-m/ min) were remained constant.
The main cutting force (Fc), feed cutting force (Ft) and temperatures
were estimated by using finite element modeling (FEM) through
ABAQUS/EXPLICIT software and the simulation was developed the
two-dimension via an orthogonal cutting process during machining
titanium alloy (Ti-6Al-4V). The results led to the conclusion that the
nose radius (Rz-mm) has affected directly on the cutting force
components. However, temperature gave no indication or has no
significant relation with nose radius during machining titanium alloy
(Ti-6Al-4V). Hence, any increase or decrease in the nose radius (Rzmm)
during machining operation led to effect on the cutting forces
and thus it will be effective on surface finish, quality, and quantity of
products.
Abstract: In emerging economies, recycling is an opportunity
for the cities to increase the lifespan of sanitary landfills, reduce the
costs of the solid waste management, decrease the environmental
problems of the waste treatment through reincorporate waste in the
productive cycle and protect and develop people’s livelihoods of
informal waste pickers. However, few studies have analysed the
possibilities and strategies to integrate formal and informal sectors in
the solid waste management for the benefit of both. This study seek
to make a strength, weakness, opportunity, and threat (SWOT)
analysis in three recycling associations of Bogotá with the aim to
understand and determine the situation of recycling from perspective
of informal sector in its transition to enter as authorized waste
providers. Data used in the analysis are derived from multiple
strategies such as literature review, the Bogota’s recycling database,
focus group meetings, governmental reports, national laws and
regulations and specific interviews with key stakeholders. Results of
this study show as the main stakeholders of formal and informal
sector of waste management can identify the internal and internal
conditions of recycling in Bogotá. Several strategies were designed
based on the SWOTs determined, could be useful for Bogotá to
advance and promote recycling as a key strategy for integrated
sustainable waste management in the city.
Abstract: Scrubbing by a liquid spraying is one of the most
effective processes used for removal of fine particles and soluble
gas pollutants (such as SO2, HCl, HF) from the flue gas. There are
many configurations of scrubbers designed to provide contact
between the liquid and gas stream for effectively capturing
particles or soluble gas pollutants, such as spray plates, packed bed
towers, jet scrubbers, cyclones, vortex and venturi scrubbers. The
primary function of venturi scrubber is the capture of fine particles
as well as HCl, HF or SO2 removal with effect of the flue gas
temperature decrease before input to the absorption column. In this
paper, sulfur dioxide (SO2) from flue gas was captured using new
design replacing venturi scrubber (1st degree of wet scrubbing).
The flue gas was prepared by the combustion of the carbon
disulfide solution in toluene (1:1 vol.) in the flame in the reactor.
Such prepared flue gas with temperature around 150°C was
processed in designed laboratory O-element scrubber. Water was
used as absorbent liquid. The efficiency of SO2 removal, pressure
drop and temperature drop were measured on our experimental
device. The dependence of these variables on liquid-gas ratio was
observed. The average temperature drop was in the range from
150°C to 40°C. The pressure drop was increased with increasing of
a liquid-gas ratio, but no too much as for the common venturi
scrubber designs. The efficiency of SO2 removal was up to 70 %.
The pressure drop of our new designed wet scrubber is similar to
commonly used venturi scrubbers; nevertheless the influence of
amount of the liquid on pressure drop is not so significant.
Abstract: We investigate relaxation dynamics of a quantum
dipole emitter (QDE), e.g., a molecule or quantum dot, located near a
metal nanoparticle (MNP) exhibiting a dipolar localized surface
plasmon (LSP) resonance at the frequency of the QDE radiative
transition. It is shown that under the condition of the QDE-MNP
characteristic relaxation time being much shorter than that of the
QDE in free-space but much longer than the LSP lifetime. It is also
shown that energy dissipation in the QDE-MNP system is relatively
weak with the probability of the photon emission being about 0.75, a
number which, rather surprisingly, does not explicitly depend on the
metal absorption characteristics. The degree of entanglement
measured by the concurrency takes the maximum value, while the
distances between the QDEs and metal ball approximately are equal.
Abstract: This paper presents the design and fabrication of an
optical window for an optical modulator toward image sensing
applications. An optical window consists of micrometer-order SiO2
capillaries (porous solid) that can modulate transmission light
intensity by moving the liquid in and out of porous solid. A high
optical transmittance of the optical window can be achieved due to
refractive index matching when the liquid is penetrated into the
porous solid. Otherwise, its light transmittance is lower because of
light reflection and scattering by air holes and capillary walls. Silicon
capillaries fabricated by deep reactive ion etching (DRIE) process are
completely oxidized to form the SiO2 capillaries. Therefore, high
aspect ratio SiO2 capillaries can be achieved based on silicon
capillaries formed by DRIE technique. Large compressive stress of
the oxide causes bending of the capillary structure, which is reduced
by optimizing the design of device structure. The large stress of the
optical window can be released via thin supporting beams. A 7.2 mm
x 9.6 mm optical window area toward a fully integrated with the
image sensor format is successfully fabricated and its optical
transmittance is evaluated with and without inserting liquids (ethanol
and matching oil). The achieved modulation range is approximately
20% to 35% with and without liquid penetration in visible region
(wavelength range from 450 nm to 650 nm).
Abstract: A cyclostationary Gaussian linearization method is
formulated for investigating the time average response of nonlinear
system under sinusoidal signal and white noise excitation. The
quantitative measure of cyclostationary mean, variance, spectrum of
mean amplitude, and mean power spectral density of noise are
analyzed. The qualitative response behavior of stochastic jump and
bifurcation are investigated. The validity of the present approach in
predicting the quantitative and qualitative statistical responses is
supported by utilizing Monte Carlo simulations. The present analysis
without imposing restrictive analytical conditions can be directly
derived by solving non-linear algebraic equations. The analytical
solution gives reliable quantitative and qualitative prediction of mean
and noise response for the Duffing system subjected to both sinusoidal
signal and white noise excitation.
Abstract: Although, lanthanum carbonate has not been approved
by the FDA for treatment of hyperphosphatemia, we prospectively
evaluated the efficacy of the combination of Calcium hydroxyapatite
(CHAp) and Lanthanum Carbonate (LaC) for the treatment of
hyperphosphatemia on mice. CHAp was prepared by co-precipitation
method using Ca(OH)2, H3PO4, NH4OH with calcination at 1200ºC.
Lanthanum carbonate was prepared by chemical method using
NaHCO3 and LaCl3 at low pH environment, below 4.0. The
structures were characterized by FTIR spectra and SEM -EDX
analysis. The study group included 16 subjects-mice divided into four
groups according to the administered substance: lanthanum carbonate
(group A), CHAp (group B), lanthanum carbonate + CHAp (group C)
and salt water (group D). The results indicate a phosphate decrease
when subjects (mice) were treated with CHAp and lanthanum
carbonate (0.5% CMC), in a single dose of 1500 mg/kg. Serum
phosphate concentration decreased [(from 4.5 ± 0.8 mg/dL) to
4.05 ± 0.2 mg/dL), P < 0.01] in group A and in group C (to 3.6
± 0.2 mg/dL) at 12 hours from the administration. The combination
of CHAp and lanthanum carbonate is a suitable regimen for
hyperphosphatemia treatment because it avoids both the
hypercalcemia of CaCO3 and the adverse effects of CHAp.
Abstract: This study investigates the suitability of using plastic,
such as polyethylene terephthalate (PET), as a partial replacement of
natural coarse and fine aggregates (for example, brick chips and
natural sand) to produce lightweight concrete for load bearing
structural members. The plastic coarse aggregate (PCA) and plastic
fine aggregate (PFA) were produced from melted polyethylene
terephthalate (PET) bottles. Tests were conducted using three
different water–cement (w/c) ratios, such as 0.42, 0.48, and 0.57,
where PCA and PFA were used as 50% replacement of coarse and
fine aggregate respectively. Fresh and hardened properties of
concrete have been compared for natural aggregate concrete (NAC),
PCA concrete (PCC) and PFA concrete (PFC). The compressive
strength of concrete at 28 days varied with the water–cement ratio for
both the PCC and PFC. Between PCC and PFC, PFA concrete
showed the highest compressive strength (23.7 MPa) at 0.42 w/c ratio
and also the lowest compressive strength (13.7 MPa) at 0.57 w/c
ratio. Significant reduction in concrete density was mostly observed
for PCC samples, ranging between 1977–1924 kg/m³. With the
increase in water–cement ratio PCC achieved higher workability
compare to both NAC and PFC. It was found that both the PCA and
PFA contained concrete achieved the required compressive strength
to be used for structural purpose as partial replacement of the natural
aggregate; but to obtain the desired lower density as lightweight
concrete the PCA is most suited.
Abstract: The quality and condition of perishable products
delivered to the market and their subsequent selling prices are
directly affected by the care taken during harvesting and handling.
Mechanical injury, in fact, occurs at all stages, from pre-harvest
operations through post-harvest handling, packing and transport to
the market. The main implications of this damage are the reduction of
the product’s quality and economical losses related to the shelf life
diminution. For most perishable products, the shelf life is relatively
short and it is typically dictated by microbial growth related to the
application of dynamic and static loads during transportation. This
paper presents the correlation between vibration levels and
microbiological growth on strawberries and woodland strawberries
and detects the presence of volatile organic compounds (VOC) in
order to develop an intelligent logistic unit capable of monitoring
VOCs using a specific sensor system. Fresh fruits were exposed to
vibrations by means of a vibrating table in a temperature-controlled
environment. Microbiological analyses were conducted on samples,
taken at different positions along the column of the crates. The values
obtained were compared with control samples not exposed to
vibrations and the results show that different positions along the
column influence the development of bacteria, yeasts and filamentous
fungi.
Abstract: Alone with fast urbanization in world, traffic control
became a big issue in urban construction. Having an efficient and
reliable traffic control system is crucial to macro-traffic control.
Traffic signal is used to manage conflicting requirement by allocating
different sets of mutually compatible traffic movement during distinct
time interval. Many approaches have been made proposed to solve
this discrete stochastic problem. Recognizing the need to minimize
right-of-way impacts while efficiently handling the anticipated high
traffic volumes, the proposed alternative system gives effective
design. This model allows for increased traffic capacity and reduces
delays by eliminating a step in maneuvering through the freeway
interchange. The concept proposed in this paper involves
construction of bridges and ramps at intersection of four roads to
control the vehicular congestion and to prevent traffic breakdown.
Abstract: Microalgae Meyerella planktonica is a potential
biofuel source because it can grow in bulk in either autotrophic or
heterotrophic condition. However, the quantitative growth of this
algal type is still low as it tends to precipitates on the bottom.
Besides, the lipid concentration is still low when grown in
autotrophic condition. In contrast, heterotrophic condition can
enhance the lipid concentration. The combination of autotrophic
condition and agitation treatment was conducted to increase the
density of the culture. On the other hand, a heterotrophic condition
was set up to raise the lipid production. A two-stage experiment
was applied to increase the density at the first step and to increase
the lipid concentration in the next step. The autotrophic condition
resulted higher density but lower lipid concentration compared to
heterotrophic one. The agitation treatment produced higher density
in both autotrophic and heterotrophic conditions. The two-stage
experiment managed to enhance the density during the autotrophic
stage and the lipid concentration during the heterotrophic stage.
The highest yield was performed by using 0.4% v/v glycerol as a
carbon source (2.9±0.016 x 10^6 cells w/w) attained 7 days after the
heterotrophic stage began. The lipid concentration was stable
starting from day 7.
Abstract: In this article, the antibiogram and heavy metal
resistance profile of the bacteria isolated from total 34 studied
animals (Pelophylax ridibundus = 12; Mauremys rivulata = 14;
Natrix natrix = 8) captured around the Biga Stream, are described.
There was no database information on antibiogram and heavy metal
resistance profile of bacteria from these area’s amphibians and
reptiles.
A total of 200 bacteria were successfully isolated from cloaca and
oral samples of the aquatic amphibians and reptiles as well as from
the water sample. According to Jaccard’s similarity index, the degree
of similarity in the bacterial flora was quite high among the
amphibian and reptile species under examination, whereas it was
different from the bacterial diversity in the water sample. The most
frequent isolates were A. hydrophila (31.5%), B. pseudomallei
(8.5%), and C. freundii (7%). The total numbers of bacteria obtained
were as follows: 45 in P. ridibundus, 45 in N. natrix 30 in M.
rivulata, and 80 in the water sample. The result showed that
cefmetazole was the most effective antibiotic to control the bacteria
isolated in this study and that approximately 93.33% of the bacterial
isolates were sensitive to this antibiotic. The multiple antibiotic
resistances (MAR) index indicated that P. ridibundus (0.95) > N.
natrix (0.89) > M. rivulata (0.39). Furthermore, all the tested heavy
metals (Pb+2, Cu+2, Cr+3, and Mn+2) inhibit the growth of the bacterial
isolates at different rates. Therefore, it indicated that the water source
of the animals was contaminated with both antibiotic residues and
heavy metals.
Abstract: Subspace channel estimation methods have been
studied widely, where the subspace of the covariance matrix is
decomposed to separate the signal subspace from noise subspace. The
decomposition is normally done by using either the eigenvalue
decomposition (EVD) or the singular value decomposition (SVD) of
the auto-correlation matrix (ACM). However, the subspace
decomposition process is computationally expensive. This paper
considers the estimation of the multipath slow frequency hopping
(FH) channel using noise space based method. In particular, an
efficient method is proposed to estimate the multipath time delays by
applying multiple signal classification (MUSIC) algorithm which is
based on the null space extracted by the rank revealing LU (RRLU)
factorization. As a result, precise information is provided by the
RRLU about the numerical null space and the rank, (i.e., important
tool in linear algebra). The simulation results demonstrate the
effectiveness of the proposed novel method by approximately
decreasing the computational complexity to the half as compared
with RRQR methods keeping the same performance.
Abstract: The main objective of this paper is to provide a new
methodology for road safety assessment in Oman through the
development of suitable accident prediction models. GLM technique
with Poisson or NBR using SAS package was carried out to develop
these models. The paper utilized the accidents data of 31 un-signalized
T-intersections during three years. Five goodness-of-fit
measures were used to assess the overall quality of the developed
models. Two types of models were developed separately; the flow-based
models including only traffic exposure functions, and the full
models containing both exposure functions and other significant
geometry and traffic variables.
The results show that, traffic exposure functions produced much
better fit to the accident data. The most effective geometric variables
were major-road mean speed, minor-road 85th percentile speed,
major-road lane width, distance to the nearest junction, and right-turn
curb radius.
The developed models can be used for intersection treatment or
upgrading and specify the appropriate design parameters of T-intersections.
Finally, the models presented in this thesis reflect the intersection
conditions in Oman and could represent the typical conditions in
several countries in the middle east area, especially gulf countries.
Abstract: This paper provides a quantitative measure of the
time-varying multiunit neuronal spiking activity using an entropy
based approach. To verify the status embedded in the neuronal activity
of a population of neurons, the discrete wavelet transform (DWT) is
used to isolate the inherent spiking activity of MUA. Due to the
de-correlating property of DWT, the spiking activity would be
preserved while reducing the non-spiking component. By evaluating
the entropy of the wavelet coefficients of the de-noised MUA, a
multiresolution Shannon entropy (MRSE) of the MUA signal is
developed. The proposed entropy was tested in the analysis of both
simulated noisy MUA and actual MUA recorded from cortex in rodent
model. Simulation and experimental results demonstrate that the
dynamics of a population can be quantified by using the proposed
entropy.