Abstract: Studies on the distribution of traffic demands have
been proceeding by providing traffic information for reducing
greenhouse gases and reinforcing the road's competitiveness in the
transport section, however, since it is preferentially required the
extensive studies on the driver's behavior changing routes and its
influence factors, this study has been developed a discriminant model
for changing routes considering driving conditions including traffic
conditions of roads and driver's preferences for information media. It
is divided into three groups depending on driving conditions in group
classification with the CART analysis, which is statistically
meaningful. And the extent that driving conditions and preferred
media affect a route change is examined through a discriminant
analysis, and it is developed a discriminant model equation to predict a
route change. As a result of building the discriminant model equation,
it is shown that driving conditions affect a route change much more,
the entire discriminant hit ratio is derived as 64.2%, and this
discriminant equation shows high discriminant ability more than a
certain degree.
Abstract: Within this work High Temperature Single Impact
Studies were performed to evaluate deformation mechanisms at
different energy and momentum levels. To show the influence of
different microstructures and hardness levels and their response to
single impacts four different materials were tested at various
temperatures up to 700°C. One carbide reinforced NiCrBSi based
Metal Matrix Composite and three different steels were tested. The
aim of this work is to determine critical energies for fracture
appearance and the materials response at different energy and
momenta levels. Critical impact loadings were examined at elevated
temperatures to limit operating conditions in impact dominated
regimes at elevated temperatures. The investigations on the
mechanisms were performed using different means of microscopy at
the surface and in metallographic cross sections. Results indicate
temperature dependence of the occurrence of cracks in hardphase
rich materials, such as Metal Matrix Composites High Speed Steels
and the influence of different impact momenta at constant energies
on the deformation of different steels.
Abstract: Wheat prediction was carried out using different meteorological variables together with agro meteorological indices in Ardebil district for the years 2004-2005 & 2005–2006. On the basis of correlation coefficients, standard error of estimate as well as relative deviation of predicted yield from actual yield using different statistical models, the best subset of agro meteorological indices were selected including daily minimum temperature (Tmin), accumulated difference of maximum & minimum temperatures (TD), growing degree days (GDD), accumulated water vapor pressure deficit (VPD), sunshine hours (SH) & potential evapotranspiration (PET). Yield prediction was done two months in advance before harvesting time which was coincide with commencement of reproductive stage of wheat (5th of June). It revealed that in the final statistical models, 83% of wheat yield variability was accounted for variation in above agro meteorological indices.
Abstract: The Electronic Health Record (EHR) system is very
general and we should pay more attention to a patient-s privacy. The
patient-s consent is one of the elements when dealing with privacy
topics. This study focuses on the creating and managing of patient
consent. The integration of the HL7 standards and the IHE BPPC
profile provides a base for the creation of patient consent. Establishing
the platform offers the patients a way to create, revoke or update their
consents. Through this platform, they can manage their consents in an
easier manner.
Abstract: Density functional theory (DFT) calculations were
performed to compute nitrogen-14 and boron-11 nuclear quadrupole
resonance (NQR) spectroscopy parameters in the representative
model of armchair boron nitride nanotube (BNNT) for the first time.
The considered model consisting of 1 nm length of H-capped (5, 5)
single-wall BNNT were first allowed to fully relax and then the NQR
calculations were carried out on the geometrically optimized model.
The evaluated nuclear quadrupole coupling constants and asymmetry
parameters for the mentioned nuclei reveal that the model can be
divided into seven layers of nuclei with an equivalent electrostatic
environment where those nuclei at the ends of tubes have a very
strong electrostatic environment compared to the other nuclei along
the length of tubes. The calculations were performed via Gaussian 98
package of program.
Abstract: Coriander is an annual and herbaceous plant, belong to
the apiaceae family. This plant is cultivated world widely. It is well
known for having medicinal properties. The aim of this experiment
was to study seed quality of species grown in Kermanshah
conditions. The experiment was carried out in research farm, Campus
of Agriculture and Natural Resources, Razi University, Kermanshah,
Iran. Coriander (local type) was grown in late spring May (5th and
20th) and Jun (4th and 19th), and plant density (10, 30, 50 and 70
plants m-2) in 2009. The experimental plots were laid out in a
factorial according to a randomized complete block design with three
replications. The fruits were harvest between 83.5 – 106.5 days after
sowing. The essential oil and oil content was extracted by Clevenger
and Soxhlet apparatuses, respectively. Results showed that delay at
planting date increased the oil content. Also, with the increase at
plant density was decreased oil content and essential oil.
Abstract: With high speed vessels getting ever more sophisti-cated, travelling at higher and higher speeds and operating in With high speed vessels getting ever more sophisticated,
travelling at higher and higher speeds and operating in areas of
high maritime traffic density, training becomes of the highest priority
to ensure that safety levels are maintained, and risks are adequately
mitigated. Training onboard the actual craft on the actual route still
remains the most effective way for crews to gain experience. However,
operational experience and incidents during the last 10 years
demonstrate the need for supplementary training whether in the area
of simulation or man to man, man/ machine interaction. Training and
familiarisation of the crew is the most important aspect in preventing
incidents. The use of simulator, computer and web based training
systems in conjunction with onboard training focusing on critical
situations will improve the man machine interaction and thereby
reduce the risk of accidents. Today, both ship simulator and bridge
teamwork courses are now becoming the norm in order to improve
further emergency response and crisis management skills. One of the
main causes of accidents is the human factor. An efficient way to
reduce human errors is to provide high-quality training to the personnel
and to select the navigators carefully.areas of high maritime traffic density, training becomes of the highest priority to ensure that safety levels are maintained, and risks are adequately mitigated. Training onboard the actual craft on the actual route still remains the most effective way for crews to gain experience. How-ever, operational experience and incidents during the last 10 years demonstrate the need for supplementary training whether in the area of simulation or man to man, man/ machine interaction. Training and familiarisation of the crew is the most important aspect in preventing incidents. The use of simulator, computer and web based training systems in conjunction with onboard training focusing on critical situations will improve the man machine interaction and thereby reduce the risk of accidents. Today, both ship simulator and bridge teamwork courses are now becoming the norm in order to improve further emergency response and crisis management skills. One of the main causes of accidents is the human factor. An efficient way to reduce human errors is to provide high-quality training to the person-nel and to select the navigators carefully. KeywordsCBT - WBT systems, Human factors.
Abstract: commercially produced in Malaysia granular
palm shell activated carbon (PSAC) was biomodified with
bacterial biomass (Bacillus subtilis) to produce a hybrid
biosorbent of higher efficiency. The obtained biosorbent was
evaluated in terms of adsorption capacity to remove copper
and zinc metal ions from aqueous solutions. The adsorption
capacity was evaluated in batch adsorption experiments where
concentrations of metal ions varied from 20 to 350 mg/L. A
range of pH from 3 to 6 of aqueous solutions containing metal
ions was tested. Langmuir adsorption model was used to
interpret the experimental data. Comparison of the adsorption
data of the biomodified and original palm shell activated
carbon showed higher uptake of metal ions by the hybrid
biosorbent. A trend in metal ions uptake increase with the
increase in the solution-s pH was observed. The surface
characterization data indicated a decrease in the total surface
area for the hybrid biosorbent; however the uptake of copper
and zinc by it was at least equal to the original PSAC at pH 4
and 5. The highest capacity of the hybrid biosorbent was
observed at pH 5 and comprised 22 mg/g and 19 mg/g for
copper and zinc, respectively. The adsorption capacity at the
lowest pH of 3 was significantly low. The experimental results
facilitated identification of potential factors influencing the
adsorption of copper and zinc onto biomodified and original
palm shell activated carbon.
Abstract: In most wheat growing moderate regions and
especially in the north of Iran climate, is affected grain filling by
several physical and abiotic stresses. In this region, grain filling often
occurs when temperatures are increasing and moisture supply is
decreasing. The experiment was designed in RCBD with split plot
arrangements with four replications. Four irrigation treatments
included (I0) no irrigation (check); (I1) one irrigation (50 mm) at
heading stage; (I2) two irrigation (100 mm) at heading and anthesis
stage; and (I3) three irrigation (150 mm) at heading, anthesis and
early grain filling growth stage, two wheat cultivars (Milan and
Shanghai) were cultured in the experiment. Totally raining was 453
mm during the growth season. The result indicated that biological
yield, grain yield and harvest index were significantly affected by
irrigation levels. I3 treatment produced more tillers number in m2,
fertile tillers number in m2, harvest index and biological yield. Milan
produced more tillers number in m2, fertile tillers in m2, while
Shanghai produced heavier tillers and grain 1000 weight. Plant height
was significant in wheat varieties while were not statistically
significant in irrigation levels. Milan produced more grain yield,
harvest index and biological yield. Grain yield shown that I1, I2, and
I3 produced increasing of 5228 (21%), 5460 (27%) and 5670 (29%)
kg ha-1, respectively. There was an interaction of irrigation and
cultivar on grain yields. In the absence of the irrigation reduced grain
1000 weight from 45 to 40 g. No irrigation reduced soil moisture
extraction during the grain filling stage. Current assimilation as a
source of carbon for grain filling depends on the light intercepting
viable green surfaces of the plant after anthesis that due to natural
senescence and the effect of various stresses. At the same time the
demand by the growing grain is increasing. It is concluded from
research work that wheat crop irrigated Milan cultivar could increase
the grain yield in comparison with Shanghai cultivar. Although, the
grain yield of Shanghai under irrigation was slightly lower than
Milan. This grain yield also was related to weather condition, sowing
date, plant density and location conditions and management of
fertilizers, because there was not significant difference in biological
and straw yield. The best result was produced by I1 treatment. I2 and
I3 treatments were not significantly difference with I1 treatment.
Grain yield of I1 indicated that wheat is under soil moisture
deficiency. Therefore, I1 irrigation was better than I0.
Abstract: New generation mobile communication networks have
the ability of supporting triple play. In order that, Orthogonal
Frequency Division Multiplexing (OFDM) access techniques have
been chosen to enlarge the system ability for high data rates
networks. Many of cross-layer modeling and optimization schemes
for Quality of Service (QoS) and capacity of downlink multiuser
OFDM system were proposed. In this paper, the Maximum Weighted
Capacity (MWC) based resource allocation at the Physical (PHY)
layer is used. This resource allocation scheme provides a much better
QoS than the previous resource allocation schemes, while
maintaining the highest or nearly highest capacity and costing similar
complexity. In addition, the Delay Satisfaction (DS) scheduling at the
Medium Access Control (MAC) layer, which allows more than one
connection to be served in each slot is used. This scheduling
technique is more efficient than conventional scheduling to
investigate both of the number of users as well as the number of
subcarriers against system capacity. The system will be optimized for
different operational environments: the outdoor deployment scenarios
as well as the indoor deployment scenarios are investigated and also
for different channel models. In addition, effective capacity approach
[1] is used not only for providing QoS for different mobile users, but
also to increase the total wireless network's throughput.
Abstract: The myocardial sintigraphy is an imaging modality which provides functional informations. Whereas, coronarography modality gives useful informations about coronary arteries anatomy. In case of coronary artery disease (CAD), the coronarography can not determine precisely which moderate lesions (artery reduction between 50% and 70%), known as the “gray zone", are haemodynamicaly significant. In this paper, we aim to define the relationship between the location and the degree of the stenosis in coronary arteries and the observed perfusion on the myocardial scintigraphy. This allows us to model the impact evolution of these stenoses in order to justify a coronarography or to avoid it for patients suspected being in the gray zone. Our approach is decomposed in two steps. The first step consists in modelling a coronary artery bed and stenoses of different location and degree. The second step consists in modelling the left ventricle at stress and at rest using the sphercical harmonics model and myocardial scintigraphic data. We use the spherical harmonics descriptors to analyse left ventricle model deformation between stress and rest which permits us to conclude if ever an ischemia exists and to quantify it.
Abstract: The pollution of sediments sampled from the North
Port by polycyclic aromatic hydrocarbons (PAHs) was investigated.
Concentrations of PAHs estimated in the port sediments ranged from
199 to 2851.2 μg/kg dw. The highest concentration was found which
is closed to the Berth line, this locations affected by intensive
shipping activities and Land based runoff and they were dominated
by the high molecular weight PAHs (4–6- rings). Source
identification showed that PAHs originated mostly from the
pyrogenic source either from the combustion of fossil fuels, grass,
wood and coal (majority of the samples). Ecological Risk Assessment
on the port sediments presented that slightly adverse ecological
effects to biological community are expected to occur at the vicinity
of the stations 1 and 4. Thus PAHs are not considered as pollutants of
concern in the North Port.
Abstract: A healthcare monitoring system is presented in this
paper. This system is based on ultra-low power sensor nodes and a
personal server, which is based on hardware and software extensions
to a Personal Digital Assistant (PDA)/Smartphone. The sensor node
collects data from the body of a patient and sends it to the personal
server where the data is processed, displayed and made ready to be
sent to a healthcare network, if necessary. The personal server
consists of a compact low power receiver module and equipped with
a Smartphone software. The receiver module takes less than 30 × 30
mm board size and consumes approximately 25 mA in active mode.
Abstract: Views on therapists- attraction have influenced the ethical and professional development of the mental health fields. Because the majority of therapist attraction literature (63.6%) has been conducted from a psychoanalytic standpoint, approaches to attraction from feminist perspectives have not been adequately developed. Considering the lack of a feminist voice regarding attraction, this article attempts to offer a feminist perspective on this issue. The purpose of this article is to offer a feminist perspective on the phenomenon of attraction in order to raise awareness about the importance of power inequalities, intersectionalities, contextual variables and the need for action in the field.
Abstract: Batteries and fuel cells contain a great potential to back up severe photovoltaic power fluctuations under inclement weather conditions. In this paper comparison between batteries and fuel cells is carried out in detail only for their PV power backup options, so their common attributes and different attributes is discussed. Then, the common and different attributes are compared; accordingly, the fuel cell is selected as the backup of Photovoltaic system. Finally, environmental evaluation of the selected hybrid plant was made in terms of plant-s land requirement and lifetime CO2 emissions, and then compared with that of the conventional fossilfuel power generating forms.
Abstract: In the frame of the European Union project entitled EU-Families and Adolescents Quit Tobacco (www.eufaqt.eu) focus group analysis has been carried out in Hungary to acquire qualitative information on attitudes towards smoking in groups of adolescents, parents and educators, respectively. It rendered to identify methods for smoking prevention/ intervention with family approach. The results explored the role of the family in smoking behaviour. Teachers do not feel responsibility in prevention or cessation of smoking. Adolescents are not aware of the addictive effect of the cigarette. Water pipe is popular among adolescent, therefore spreading of more information needed on the harmful effects of water pipe. We outlined the requirement for professionals to provide interventions. Partnership of EU-FAQT project has worked out antismoking interventions for adolescents and their families conducted by psychologists to ensure skill development to prevent and quit tobacco.
Abstract: Sarkhoon gas plant, located in south of Iran, has been installed to removal H2S contained in a high pressure natural gas stream. The solvent used for the H2S removal from gaseous stream is 34% by weight (wt%) Di-ethanol amine (DEA) solutions. Due to increasing concentration of heat stable salt (HSS) in solvent, corrosivity of amine solution had been increased. Reports indicated that there was corrosion on the shell of regeneration column. Because source formation of HSS was unknown, we decided to control the amount of HSS at the limit less than 3% wt amine solvent. Therefore, two small columns were filled by strong anionic base and carbon active, and then polluted amine was passed through beds. Finally a temporary amine recovery package on industrial scale was made based on laboratory’s results. From economical point of view we could save $700000 beside corrosion occurrence of the stripping column has been vigorously decreased.
Abstract: Nowadays, power systems, energy generation by wind
has been very important. Noting that the production of electrical
energy by wind turbines on site to several factors (such as wind speed
and profile site for the turbines, especially off the wind input speed,
wind rated speed and wind output speed disconnect) is dependent. On
the other hand, several different types of turbines in the market there.
Therefore, selecting a turbine that its capacity could also answer the
need for electric consumers the efficiency is high something is
important and necessary. In this context, calculating the amount of
wind power to help optimize overall network, system operation, in
determining the parameters of wind power is very important.
In this article, to help calculate the amount of wind power plant,
connected to the national network in the region Manjil wind,
selecting the best type of turbine and power delivery profile
appropriate to the network using Monte Carlo method has been.
In this paper, wind speed data from the wind site in Manjil, as minute
and during the year has been. Necessary simulations based on
Random Numbers Simulation method and repeat, using the software
MATLAB and Excel has been done.
Abstract: Lean, which was initially developed by Toyota, is
widely implemented in other companies to improve competitiveness.
This research is an attempt to identify the adoption of lean in the
production system of Malaysian car manufacturer, Proton using case
study approach. To gain the in-depth information regarding lean
implementation, an activity on the assembly line called Set Parts
Supply (SPS) was studied. The result indicates that by using lean
principles, tools and techniques in the implementation of SPS enabled
to achieve the goals on safety, quality, cost, delivery and morale. The
implementation increased the size of the workspace, improved the
quality of assembly and the delivery of parts supply, reduced the
manpower, achieved cost savings on electricity and also increased the
motivation of manpower in respect of attendance at work. A
framework of SPS implementation is suggested as a contribution for
lean practices in production system.
Abstract: The objective of this research is to study the people’s level of participation in activities of the community, their satisfaction towards the community, the attachment they have to the community, factors that influence the attachment, as well as the characteristics of the relationships of military families’ of the Royal Guards community of Dusit District. The method used was non-probability sampling by quota sampling according to people’s age. The determined age group was 18 years or older.
One set of a sample group was done per family. The questionnaires were conducted by 287 people. Snowball sampling was also used by interviewing people of the community, starting from the Royal Guards Community’s leader, then by 20 of the community’s well-respected persons. The data was analyzed by using descriptive statistics, such as arithmetic mean and standard deviation, as well as by inferential statistics, such as Independent - Samples T test (T-test), One-Way ANOVA (F-test), Chi-Square. Descriptive analysis according to the structure of the interview content was also used. The results of the research is that the participation of the population in the Royal Guards Community in various activities is at a medium level, with the average participation level during Mother’s and Father’s Days. The people’s general level of satisfaction towards the premises of the Royal Guards Community is at the highest level.
The people were most satisfied with the transportation within the community and in contacting with people from outside the premises. The access to the community is convenient and there are various entrances. The attachment of the people to the Royal Guards Community in general and by each category is at a high level. The feeling that the community is their home rated the highest average. Factors that influence the attachment of the people of the Royal Guards Community are age, status, profession, income, length of stay in the community, membership of social groups, having neighbors they feel close and familiar with, and as well as the benefits they receive from the community. In addition, it was found that people that participate in activities have a high level of positive relationship towards the attachment of the people to the Royal Guards Community. The satisfaction of the community has a very high level of positive relationship with the attachment of the people to the Royal Guards Community.
The characteristics of the attachment of military families’ is that they live in big houses that everyone has to protect and care for, starting from the leader of the family as well as all members. Therefore, they all love the community they live in. The characteristics that show the participation of activities within the community and the high level of satisfaction towards the premises of the community will enable the people to be more attached to the community. The people feel that everyone is close neighbors within the community, as if they are one big family.