Abstract: The composite flour blend consisting of corn, pearl
millet, black gram and wheat bran in the ratio of 80:5:10:5 was taken
to prepare the extruded product and their effect on physical properties
of extrudate was studied. The extrusion process was conducted in
laboratory by using twin screw extruder. The physical characteristics
evaluated include lateral expansion, bulk density, water absorption
index, water solubility index, and rehydration ratio and moisture
retention. The Central Composite Rotatable Design (CCRD) was
used to decide the level of processing variables i.e. feed moisture
content (%), screw speed (rpm), and barrel temperature (oC) for the
experiment. The data obtained after extrusion process were analyzed
by using response surface methodology. A second order polynomial
model for the dependent variables was established to fit the
experimental data. The numerical optimization studies resulted in
127°C of barrel temperature, 246 rpm of screw speed, and 14.5% of
feed moisture as optimum variables to produce acceptable extruded
product. The responses predicted by the software for the optimum
process condition resulted in lateral expansion 126%, bulk density
0.28 g/cm3, water absorption index 4.10 g/g, water solubility index
39.90%, rehydration ratio 544% and moisture retention 11.90% with
75% desirability.
Abstract: The recent interest in alternative and renewable
energy systems results in increased installed capacity ratio of such
systems in total energy production of the world. Specifically, Wind
Energy Conversion Systems (WECS) draw significant attention
among possible alternative energy options, recently. On the contrary
of the positive points of penetrating WECS in all over the world in
terms of environment protection, energy independence of the
countries, etc., there are significant problems to be solved for the grid
connection of large scale WECS. The reactive power regulation,
voltage variation suppression, etc. can be presented as major issues to
be considered in this regard. Thus, this paper evaluates the
application of a Static VAr Compensator (SVC) unit for the reactive
power regulation and operation continuity of WECS during a fault
condition. The system is modeled employing the IEEE 13 node test
system. Thus, it is possible to evaluate the system performance with
an overall grid simulation model close to real grid systems. The
overall simulation model is developed in
MATLAB/Simulink/SimPowerSystems® environments and the
obtained results effectively match the target of the provided study.
Abstract: Coal tar is a liquid by-product of coal pyrolysis
processes. This liquid oil mixture contains various kinds of useful
compounds such as benzoic aromatic compounds and phenolic
compounds. These compounds are widely used as raw material for
insecticides, dyes, medicines, perfumes, coloring matters, and many
others. The coal tar was collected by pyrolysis process of coal
obtained from PT Kaltim Prima Coal and Arutmin-Kalimantan. The
experiments typically occurred at the atmospheric pressure in a
laboratory furnace at temperatures ranging from 300 to 550oC with a
heating rate of 10oC/min and a holding time of 1 hour at the pyrolysis
temperature. The Gas Chromatography-Mass Spectroscopy (GC-MS)
was used to analyze the coal tar components. The obtained coal tar
has the viscosity of 3.12 cp, the density of 2.78 g/cm3, the calorific
value of 11,048.44 cal/g, and the molecular weight of 222.67. The
analysis result showed that the coal tar contained more than 78
chemical compounds such as benzene, cresol, phenol, xylene,
naphtalene, etc. The total phenolic compounds contained in coal tar
are 33.25% (PT KPC) and 17.58% (Arutmin-Kalimantan). The total
naphtalene compounds contained in coal tar is 14.15% (PT KPC) and
17.13% (Arutmin-Kalimantan).
Abstract: The aim of our study is to project an optimized wind turbine of Darrieus type. This type of wind turbine is characterized by a low starting torque in comparison with the Savonius rotor allowing them to operate for a period greater than wind speed. This led us to reconsider the Darrieus rotor to optimize a design which will increase its starting torque. The study of a system of monitoring and control of the angle of attack of blade profile, which allows an auto start to wind speeds as low as possible is presented for the straight blade of Darrieus turbine. The study continues to extend to other configurations namely those of parabolic type.
Abstract: Synthesis of gold nanoparticles has attracted much
attention since the pioneering discovery of the high catalytic activity
of supported gold nanoparticles in the reaction of CO oxidation at
low temperature. In this research field, we used Na-montmorillonite
for gold nanoparticles stabilization; various gold loading percentage
1, 2 and 5% were used for gold nanoparticles preparation. The gold
nanoparticles were obtained using chemical reduction method using
NaBH4 as reductant agent. The obtained gold nanoparticles stabilized
in Na-montmorillonite were used as catalysts for the reduction of 4-
nitrophenol to aminophenol with sodium borohydride at room
temperature. The UV-Vis results confirmed directly the gold
nanoparticles formation. The XRD and N2 adsorption results showed
the formation of gold nanoparticles in the pores of montmorillonite
with an average size of 5 nm obtained on samples with 2% gold
loading percentage. The gold particles size increased with the
increase of gold loading percentage. The reduction reaction of 4-
nitrophenol into 4-aminophenol with NaBH4 catalyzed by Au-Namontmorillonite
catalyst exhibits remarkably a high activity; the
reaction was completed within 9 min for 1%Au-Na-montmorillonite
and within 3 min for 2%Au-Na-montmorillonite.
Abstract: The spindle system is one of the most important
components of machine tool. The dynamic properties of the spindle
affect the machining productivity and quality of the work pieces.
Thus, it is important and necessary to determine its dynamic
characteristics of spindles in the design and development in order to
avoid forced resonance. The finite element method (FEM) has been
adopted in order to obtain the dynamic behavior of spindle system.
For this reason, obtaining the Campbell diagrams and determining the
critical speeds are very useful to evaluate the spindle system
dynamics. The unbalance response of the system to the center of
mass unbalance at the cutting tool is also calculated to investigate the
dynamic behavior. In this paper, we used an ANSYS Parametric
Design Language (APDL) program which based on finite element
method has been implemented to make the full dynamic analysis and
evaluation of the results. Results show that the calculated critical
speeds are far from the operating speed range of the spindle, thus, the
spindle would not experience resonance, and the maximum
unbalance response at operating speed is still with acceptable limit.
ANSYS Parametric Design Language (APDL) can be used by spindle
designer as tools in order to increase the product quality, reducing
cost, and time consuming in the design and development stages.
Abstract: In this communication, a low-cost circularly
polarized wire antenna exhibiting improved gain performance for
Dedicated Short Range Communications (DSRC), vehicle-to-vehicle
(V2V) and vehicle-to-infrastructure (V2I) communications is
presented. The proposed antenna comprises a Y-shaped quarterwavelength
monopole antenna surrounded by two iterations of eight
conductive arched walls acting as parasitic elements to enhance the
overall antenna gain and to shape the radiation pattern in the H-plane.
A hemispherical radome shell is added to protect the antenna
structure and its effect on the antenna performance is discussed. The
designed antenna demonstrates antenna gain of 8.2 dB with
omnidirectional far-field radiation pattern in the H-plane. The gain of
the proposed antenna is also compared with the characteristic of the
stand-alone Y-shaped monopole to highlight the advantages of the
proposed approach.
Abstract: This study analyzes the critical gaps in the
architecture of European stability and the expected role of the
banking union as the new important step towards completing the
Economic and Monetary Union that should enable the creation of
safe and sound financial sector for the euro area market. The single
rulebook together with the Single Supervisory Mechanism and the
Single Resolution Mechanism - as two main pillars of the banking
union, should provide a consistent application of common rules and
administrative standards for supervision, recovery and resolution of
banks – with the final aim of replacing the former bail-out practice
with the bail-in system through which possible future bank failures
would be resolved by their own funds, i.e. with minimal costs for
taxpayers and real economy. In this way, the vicious circle between
banks and sovereigns would be broken. It would also reduce the
financial fragmentation recorded in the years of crisis as the result of
divergent behaviors in risk premium, lending activities and interest
rates between the core and the periphery. In addition, it should
strengthen the effectiveness of monetary transmission channels, in
particular the credit channels and overflows of liquidity on the money
market which, due to the fragmentation of the common financial
market, has been significantly disabled in period of crisis. However,
contrary to all the positive expectations related to the future
functioning of the banking union, major findings of this study
indicate that characteristics of the economic system in which the
banking union will operate should not be ignored. The euro area is an
integration of strong and weak entities with large differences in
economic development, wealth, assets of banking systems, growth
rates and accountability of fiscal policy. The analysis indicates that
low and unbalanced economic growth remains a challenge for the
maintenance of financial stability and this problem cannot be
resolved just by a single supervision. In many countries bank assets
exceed their GDP by several times and large banks are still a matter
of concern, because of their systemic importance for individual
countries and the euro zone as a whole. The creation of the Single
Supervisory Mechanism and the Single Resolution Mechanism is a
response to the European crisis, which has particularly affected
peripheral countries and caused the associated loop between the
banking crisis and the sovereign debt crisis, but has also influenced
banks’ balance sheets in the core countries, as the result of crossborder
capital flows. The creation of the SSM and the SRM should
prevent the similar episodes to happen again and should also provide
a new opportunity for strengthening of economic and financial
systems of the peripheral countries. On the other hand, there is a
potential threat that future focus of the ECB, resolution mechanism
and other relevant institutions will be extremely oriented towards
large and significant banks (whereby one half of them operate in the
core and most important euro area countries), and therefore it remains
questionable to what extent will the common resolution funds will be used for rescue of less important institutions. Recent geopolitical
developments will be the optimal indicator to show whether the
previously established mechanisms are sufficient enough to maintain
the adequate financial stability in the euro area market.
Abstract: Liquid-Liquid Equilibrium (LLE) data are measured
for the ternary mixtures of water + 1-butanol + butyl acetate and
quaternary mixtures of water + 1-butanol + butyl acetate + glycerol at
atmospheric pressure at 313.15 K. In addition, isothermal
vapor–liquid–liquid equilibrium (VLLE) data are determined
experimentally at 333.15 K. The region of heterogeneity is found to
increase as the hydrophilic agent (glycerol) is introduced into the
aqueous mixtures. The experimental data are correlated with the
NRTL model. The predicted results from the solution model with the
model parameters determined from the constituent binaries are also
compared with the experimental values.
Abstract: A flow column has been innovatively used in the
design of a new electrocoagulation reactor (ECR1) that will reduce
the temperature of water being treated; where the flow columns work
as a radiator for the water being treated. In order to investigate the
performance of ECR1 and compare it to that of traditional reactors;
600 mL water samples with an initial temperature of 350C were
pumped continuously through these reactors for 30 min at current
density of 1 mA/cm2. The temperature of water being treated was
measured at 5 minutes intervals over a 30 minutes period using a
thermometer. Additional experiments were commenced to investigate
the effects of initial temperature (15-350C), water conductivity (0.15
– 1.2 S) and current density (0.5 -3 mA/cm2) on the performance of
ECR1.
The results obtained demonstrated that the ECR1, at a current
density of 1 mA/cm2 and continuous flow model, reduced water
temperature from 350C to the vicinity of 280C during the first 15
minutes and kept the same level till the end of the treatment time.
While, the temperature increased from 28.1 to 29.80C and from 29.8
to 31.90C in the batch and the traditional continuous flow models
respectively. In term of initial temperature, ECR1 maintained the
temperature of water being treated within the range of 22 to 280C
without the need for external cooling system even when the initial
temperatures varied over a wide range (15 to 350C). The influent
water conductivity was found to be a significant variable that affect
the temperature. The desirable value of water conductivity is 0.6 S.
However, it was found that the water temperature increased rapidly
with a higher current density.
Abstract: Geographical routing protocol requires node physical
location information to make forwarding decision. Geographical
routing uses location service or position service to obtain the position
of a node. The geographical information is a geographic coordinates
or can be obtained through reference points on some fixed coordinate
system. Link can be formed between two nodes. Link lifetime plays a
crucial role in MANET. Link lifetime represent how long the link is
stable without any failure between the nodes. Link failure may occur
due to mobility and because of link failure energy of nodes can be
drained. Thus this paper proposes survey about link lifetime
prediction using geographical information.
Abstract: Tannase (tannin acyl hydrolase, E.C.3.1.1.20) is an
important hydrolysable enzyme with innumerable applications and
industrial potential. In the present study, a kinetic model has been
developed for the batch fermentation used for the production of
tannase by A.flavus MTCC 3783. Maximum tannase activity of
143.30 U/ml was obtained at 96 hours under optimum operating
conditions at 35oC, an initial pH of 5.5 and with an inducer tannic
acid concentration of 3% (w/v) for a fermentation period of 120
hours. The biomass concentration reaches a maximum of 6.62 g/l at
96 hours and further there was no increase in biomass concentration
till the end of the fermentation. Various unstructured kinetic models
were analyzed to simulate the experimental values of microbial
growth, tannase activity and substrate concentration. The Logistic
model for microbial growth , Luedeking - Piret model for production
of tannase and Substrate utilization kinetic model for utilization of
substrate were capable of predicting the fermentation profile with
high coefficient of determination (R2) values of 0.980, 0.942 and
0.983 respectively. The results indicated that the unstructured models
were able to describe the fermentation kinetics more effectively.
Abstract: Mobile Ad hoc Network is a set of self-governing
nodes which communicate through wireless links. Dynamic topology
MANETs makes routing a challenging task. Various routing
protocols are there, but due to various fundamental characteristic
open medium, changing topology, distributed collaboration and
constrained capability, these protocols are tend to various types of
security attacks. Black hole is one among them. In this attack,
malicious node represents itself as having the shortest path to the
destination but that path not even exists. In this paper, we aim to
develop a routing protocol for detection and prevention of black hole
attack by modifying AODV routing protocol. This protocol is able to
detect and prevent the black hole attack. Simulation is done using
NS-2, which shows the improvement in network performance.
Abstract: File sharing in networks is generally achieved using
Peer-to-Peer (P2P) applications. Structured P2P approaches are
widely used in adhoc networks due to its distributed and scalability
features. Efficient mechanisms are required to handle the huge
amount of data distributed to all peers. The intrinsic characteristics of
P2P system makes for easier content distribution when compared to
client-server architecture. All the nodes in a P2P network act as both
client and server, thus, distributing data takes lesser time when
compared to the client-server method. CHORD protocol is a resource
routing based where nodes and data items are structured into a 1-
dimensional ring. The structured lookup algorithm of Chord is
advantageous for distributed P2P networking applications. However,
structured approach improves lookup performance in a high
bandwidth wired network it could contribute to unnecessary overhead
in overlay networks leading to degradation of network performance.
In this paper, the performance of existing CHORD protocol on
Wireless Mesh Network (WMN) when nodes are static and dynamic
is investigated.
Abstract: Life cycle assessment is a technique to assess the
environmental aspects and potential impacts associated with a
product, process, or service, by compiling an inventory of relevant
energy and material inputs and environmental releases; evaluating the
potential environmental impacts associated with identified inputs and
releases; and interpreting the results to help you make a more
informed decision. In this paper, the life cycle assessment of
aluminum and beech wood as two commonly used materials in Egypt
for window frames are heading, highlighting their benefits and
weaknesses. Window frames of the two materials have been assessed
on the basis of their production, energy consumption and
environmental impacts. It has been found that the climate change of
the windows made of aluminum and beech wood window, for a
reference window (1.2m×1.2m), are 81.7 mPt and -52.5 mPt impacts
respectively. Among the most important results are: fossil fuel
consumption, potential contributions to the green building effect and
quantities of solid waste tend to be minor for wood products
compared to aluminum products; incineration of wood products can
cause higher impacts of acidification and eutrophication than
aluminum, whereas thermal energy can be recovered.
Abstract: This paper presents the results obtained by numerical
simulation using the software ANSYS CFX-CFD for the air
pollutants dispersion in the atmosphere coming from the evacuation
of combustion gases resulting from the fuel combustion in an electric
thermal power plant. The model uses the Navier-Stokes equation to
simulate the dispersion of pollutants in the atmosphere. It is
considered as important factors in elaboration of simulation the
atmospheric conditions (pressure, temperature, wind speed, wind
direction), the exhaust velocity of the combustion gases, chimney
height and the obstacles (buildings). Using the air quality monitoring
stations it is measured the concentrations of main pollutants (SO2,
NOx and PM). The pollutants were monitored over a period of 3
months, after that the average concentration are calculated, which is
used by the software. The concentrations are: 8.915 μg/m3 (NOx),
9.587 μg/m3 (SO2) and 42 μg/m3 (PM). A comparison of test data
with simulation results demonstrated that CFX was able to describe
the dispersion of the pollutant as well the concentration of this
pollutants in the atmosphere.
Abstract: In this paper, analysis of an infinite beam resting on
multilayer tensionless extensible geosynthetic reinforced granular
fill-poor soil system overlying soft soil strata under moving load with
constant velocity is presented. The beam is subjected to a
concentrated load moving with constant velocity. The upper
reinforced granular bed is modeled by a rough membrane embedded
in Pasternak shear layer overlying a series of compressible nonlinear
winkler springs representing the underlying the very poor soil. The
multilayer tensionless extensible geosynthetic layer has been
assumed to deform such that at interface the geosynthetic and the soil
have some deformation. Nonlinear behaviour of granular fill and the
very poor soil has been considered in the analysis by means of
hyperbolic constitutive relationships. Governing differential
equations of the soil foundation system have been obtained and
solved with the help of appropriate boundary conditions. The solution
has been obtained by employing finite difference method by means of
Gauss-Siedal iterative scheme. Detailed parametric study has been
conducted to study the influence of various parameters on the
response of soil–foundation system under consideration by means of
deflection and bending moment in the beam and tension mobilized in
the geosynthetic layer. These parameters include magnitude of
applied load, velocity of load, damping, ultimate resistance of poor
soil and granular fill layer. Range of values of parameters has been
considered as per Indian Railway conditions. This study clearly
observed that the comparisons of multilayer tensionless extensible
geosynthetic reinforcement with poor foundation soil and magnitude
of applied load, relative compressibility of granular fill and ultimate
resistance of poor soil has significant influence on the response of
soil–foundation system.
Abstract: The purpose of this study is the discrimination of 28
postmenopausal with osteoporotic femoral fractures from an agematched
control group of 28 women using texture analysis based on
fractals. Two pre-processing approaches are applied on radiographic
images; these techniques are compared to highlight the choice of the
pre-processing method. Furthermore, the values of the fractal
dimension are compared to those of the fractal signature in terms of
the classification of the two populations. In a second analysis, the
BMD measure at proximal femur was compared to the fractal
analysis, the latter, which is a non-invasive technique, allowed a
better discrimination; the results confirm that the fractal analysis of
texture on calcaneus radiographs is able to discriminate osteoporotic
patients with femoral fracture from controls. This discrimination was
efficient compared to that obtained by BMD alone. It was also
present in comparing subgroups with overlapping values of BMD.
Abstract: In this paper comprehensive studies have been carried
out for the design optimization of a waste heat recovery system for
effectively utilizing the domestic air conditioner heat energy for
producing hot water. Numerical studies have been carried for the
geometry optimization of a waste heat recovery system for domestic
air conditioners. Numerical computations have been carried out using
a validated 2d pressure based, unsteady, 2nd-order implicit, SST k-ω
turbulence model. In the numerical study, a fully implicit finite
volume scheme of the compressible, Reynolds-Averaged, Navier-
Stokes equations is employed. At identical inflow and boundary
conditions various geometries were tried and effort has been taken for
proposing the best design criteria. Several combinations of pipe line
shapes viz., straight and spiral with different number of coils for the
radiator have been attempted and accordingly the design criteria has
been proposed for the waste heat recovery system design. We have
concluded that, within the given envelope, the geometry optimization
is a meaningful objective for getting better performance of waste heat
recovery system for air conditioners.
Abstract: This paper applied factor conditions from Porter’s
Diamond Model (1990) to understand the various challenges facing
the AMISA. Factor conditions highlighted in Porter’s model are
grouped into two groups namely, basic and advance factors. Two
AMISA associations representing over 10 000 employees were
interviewed. The largest Clothing, Textiles and Leather (CTL)
apparel retail group was also interviewed with a government
department implementing the industrialization policy were
interviewed. The paper points out that AMISA have basic factor conditions
necessary for competitive advantage in the apparel industries.
However advance factor creation has proven to be a challenge for
AMISA, Higher Education Institutions (HEIs) and government. Poor
infrastructural maintenance has contributed to high manufacturing
costs and poor quick response technologies. The use of Porter’s
Factor Conditions as a tool to analyze the sector’s competitive
advantage challenges and opportunities has increased knowledge
regarding factors that limit the AMISA’s competitiveness. It is
therefore argued that other studies on Porter’s Diamond model
factors like Demand conditions, Firm strategy, structure and rivalry
and Related and supporting industries can be used to analyze the
situation of the AMISA for the purposes of improving competitive
advantage.