Abstract: In this paper fatigue crack growth behavior of
aeronautical aluminum alloy 2024 T351 was studied. Effects of
various loading and geometrical parameters are studied such as stress
ratio, amplitude loading, etc. The fatigue crack growth with constant
amplitude is studied using the AFGROW code when NASGRO
model is used. The effect of the stress ratio is highlighted, where one
notices a shift of the curves of crack growth. The comparative study
between two orientations L-T and T-L on fatigue behavior are
presented and shows the variation on the fatigue life. L-T orientation
presents a good fatigue crack growth resistance. Effects of crack
closure are shown in Paris domain and that no crack closure
phenomenons are present at high stress intensity factor.
Abstract: The problem of robust disturbance rejection (RDR) using a proportional state feedback controller is studied for the case of Left Invertible MIMO generalized state space linear systems with nonlinear uncertain structure. Sufficient conditions for the problem to have a solution are established. The set of all proportional feedback controllers solving the problem subject to these conditions is analytically determined.
Abstract: This paper deals with the current space-vector
decomposition in three-phase, three-wire systems on the basis of
some case studies. We propose four components of the current spacevector
in terms of DC and AC components of the instantaneous
active and reactive powers. The term of supplementary useless
current vector is also pointed out. The analysis shows that the current
decomposition which respects the definition of the instantaneous
apparent power vector is useful for compensation reasons only if the
supply voltages are sinusoidal. A modified definition of the
components of the current is proposed for the operation under
nonsinusoidal voltage conditions.
Abstract: Hopfield model of associative memory is studied in this work. In particular, two main problems that it possesses: the apparition of spurious patterns in the learning phase, implying the well-known effect of storing the opposite pattern, and the problem of its reduced capacity, meaning that it is not possible to store a great amount of patterns without increasing the error probability in the retrieving phase. In this paper, a method to avoid spurious patterns is presented and studied, and an explanation of the previously mentioned effect is given. Another technique to increase the capacity of a network is proposed here, based on the idea of using several reference points when storing patterns. It is studied in depth, and an explicit formula for the capacity of the network with this technique is provided.
Abstract: This work presents a neural network model for the
clustering analysis of data based on Self Organizing Maps (SOM).
The model evolves during the training stage towards a hierarchical
structure according to the input requirements. The hierarchical structure
symbolizes a specialization tool that provides refinements of the
classification process. The structure behaves like a single map with
different resolutions depending on the region to analyze. The benefits
and performance of the algorithm are discussed in application to the
Iris dataset, a classical example for pattern recognition.
Abstract: Simplified coupled engine block-crankshaft models
based on beam theory provide an efficient substitute to engine
simulation in the design process. These models require accurate
definition of the main bearing stiffness. In this paper, an investigation
of this stiffness is presented. The clearance effect is studied using a
smooth bearing model. It is manifested for low shaft displacement.
The hydrodynamic assessment model shows that the oil film has no
stiffness for low loads and it is infinitely rigid for important loads.
The deformation stiffness is determined using a suitable finite
elements model based on real CADs. As a result, a main bearing
behaviour law is proposed. This behaviour law takes into account the
clearance, the hydrodynamic sustention and the deformation stiffness.
It ensures properly the transition from the configuration low rigidity
to the configuration high rigidity.
Abstract: The aim of this research is to evaluate surface
roughness and develop a multiple regression model for surface roughness as a function of cutting parameters during the turning of
flame hardened medium carbon steel with TiN-Al2O3-TiCN coated inserts. An experimental plan of work and signal-to-noise ratio (S/N)
were used to relate the influence of turning parameters to the
workpiece surface finish utilizing Taguchi methodology. The effects
of turning parameters were studied by using the analysis of variance (ANOVA) method. Evaluated parameters were feed, cutting speed,
and depth of cut. It was found that the most significant interaction among the considered turning parameters was between depth of cut and feed. The average surface roughness (Ra) resulted by TiN-Al2O3-
TiCN coated inserts was about 2.44 μm and minimum value was 0.74 μm. In addition, the regression model was able to predict values for surface roughness in comparison with experimental values within
reasonable limit.
Abstract: Argument over the use of particular method in interlanguage pragmatics has increased recently. Researchers argued the advantages and disadvantages of each method either natural or elicited. Findings of different studies indicated that the use of one method may not provide enough data to answer all its questions. The current study investigated the validity of using multimethod approach in interlanguage pragmatics to understand the development of requests in Arabic as a second language (Arabic L2). To this end, the study adopted two methods belong to two types of data sources: the institutional discourse (natural data), and the role play (elicited data). Participants were 117 learners of Arabic L2 at the university level, representing four levels (beginners, low-intermediate, highintermediate, and advanced). Results showed that using two or more methods in interlanguage pragmatics affect the size and nature of data.
Abstract: Image mosaicing is a technique that permits to enlarge the field of view of a camera. For instance, it is employed to achieve panoramas with common cameras or even in scientific applications, to achieve the image of a whole culture in microscopical imaging. Usually, a mosaic of cell cultures is achieved through using automated microscopes. However, this is often performed in batch, through CPU intensive minimization algorithms. In addition, live stem cells are studied in phase contrast, showing a low contrast that cannot be improved further. We present a method to study the flat field from live stem cells images even in case of 100% confluence, this permitting to build accurate mosaics on-line using high performance algorithms.
Abstract: This paper presents a ray tracing simulation technique for characterize the radiowave propagation inside building. The implementation of an algorithm capable of enumerating a large number of propagation paths in interactive time for the special case of 2.5D. The effective dielectric constants of the building structure in the simulations are indicated. The study describes an efficient 2.5D model of ray tracing algorithm were compared with 3D model. The result of the first investigations is that the environment of the indoor wave significantly changes as we change the electric parameters of material constructions. A detailed analysis of the dependence of the indoor wave on the wideband characteristics of the channel: root mean square (RMS) delay spread characteristics and Mean excess delay, is also investigated.
Abstract: Free and open source software is gaining popularity at
an unprecedented rate of growth. Organizations despite some
concerns about the quality have been using them for various
purposes. One of the biggest concerns about free and open source
software is post release software defects and their fixing. Many
believe that there is no appropriate support available to fix the bugs.
On the contrary some believe that due to the active involvement of
internet user in online forums, they become a major source of
communicating the identification and fixing of defects in open source
software. The research model of this empirical investigation
establishes and studies the relationship between open source software
defects and online public forums. The results of this empirical study
provide evidence about the realities of software defects myths of
open source software. We used a dataset consist of 616 open source
software projects covering a broad range of categories to study the
research model of this investigation. The results of this investigation
show that online forums play a significant role identifying and fixing
the defects in open source software.
Abstract: Hydrogenated biodiesel is one of the most promising
renewable fuels. It has many advantages over conventional biodiesel,
including higher cetane number, higher heating value, lower
viscosity, and lower corrosiveness due to its absence of oxygen.
From previous work, Pd/TiO2 gave high conversion and selectivity in
hydrogenated biodiesel. In this work, the effect of biomass feedstocks
(i.e. beef fat, chicken fat, pork fat, and jatropha oil) on the production
of hydrogenated biodiesel over Pd/TiO2 has been studied. Biomass
feedstocks were analyzed by ICP-OES (inductively coupled plasma
optical emission spectrometry) to identify the content of impurities
(i.e. P, K, Ca, Na, and Mg). The deoxygenation catalyst, Pd/TiO2,
was prepared by incipient wetness impregnation (IWI) and tested in a
continuous flow packed-bed reactor at 500 psig, 325°C, H2/feed
molar ratio of 30, and LHSV of 4 h-1 for its catalytic activity and
selectivity in hydrodeoxygenation. All feedstocks gave high
selectivity in diesel specification range hydrocarbons and the main
hydrocarbons were n-pentadecane (n-C15) and n-heptadecane (n-
C17), resulting from the decarbonylation/decarboxylation reaction.
Intermediates such as oleic acid, stearic acid, palmitic acid, and esters
were also detected in minor amount. The conversion of triglycerides
in jatropha oil is higher than those of chicken fat, pork fat, and beef
fat, respectively. The higher concentration of metal impurities in
feedstock, the lower conversion of feedstock.
Abstract: In this document we studied more in detail the Performances of the vertical handover in the networks WLAN, WiMAX, UMTS before studying of it the Procedure of Handoff Vertical, the whole buckled by simulations putting forward the performances of the handover in the heterogeneous networks. The goal of Vertical Handover is to carry out several accesses in real-time in the heterogeneous networks. This makes it possible a user to use several networks (such as WLAN UMTS andWiMAX) in parallel, and the system to commutate automatically at another basic station, without disconnecting itself, as if there were no cut and with little loss of data as possible.
Abstract: In this paper, many techniques for blind identification of moving average (MA) process are presented. These methods utilize third- and fourth-order cumulants of the noisy observations of the system output. The system is driven by an independent and identically distributed (i.i.d) non-Gaussian sequence that is not observed. Two nonlinear optimization algorithms, namely the Gradient Descent and the Gauss-Newton algorithms are exposed. An algorithm based on the joint-diagonalization of the fourth-order cumulant matrices (FOSI) is also considered, as well as an improved version of the classical C(q, 0, k) algorithm based on the choice of the Best 1-D Slice of fourth-order cumulants. To illustrate the effectiveness of our methods, various simulation examples are presented.
Abstract: Research results and optimal parameters investigation
of laser cut and profiling of diamond and quartz substrates by
femtosecond laser pulses are presented. Profiles 10 μm in width, ~25
μm in depth and several millimeters long were made. Investigation of
boundaries quality has been carried out with the use of AFM
«Vecco». Possibility of technological formation of profiles and
micro-holes in diamond and quartz substrates with nanometer-scale
boundaries is shown. Experimental results of multilayer dielectric
cover treatment are also presented. Possibility of precise upper layer
(thickness of 70–140 nm) removal is demonstrated. Processes of thin
metal film (60 nm and 350 nm thick) treatment are considered.
Isolation tracks (conductance ~ 10-11 S) 1.6–2.5 μm in width in
conductive metal layers are formed.
Abstract: The paper describes the workings for four models of
CONWIP systems used till date; the basic CONWIP system, the
hybrid CONWIP system, the multi-product CONWIP system, and the
parallel CONWIP system. The final novel model is introduced in this
paper in a general form. These models may be adopted for analysis
for both simulation studies and implementation on the shop floor. For
each model, input parameters of interest are highlighted and their
impacts on several system performance measures are addressed.
Abstract: Monoculture and mixed cultures of microalgae and
the oleaginous yeast for microbial oil productions were investigated
using sugarcane juice as carbon substrate. The monoculture of yeast
Torulaspora maleeae Y30, Torulaspora globosa YU5/2 grew faster
than that of microalgae Chlorella sp. KKU-S2. In monoculture of T.
maleeae Y30, a biomass of 8.267g/L with lipid yield of 0.920g/L
were obtained, while 8.333g/L of biomass with lipid yield of
1.141g/L were obtained for monoculture of T. globosa YU5/2. A
biomass of 1.933g/L with lipid yield of 0.052g/L was found for
monoculture of Chlorella sp. KKU-S2. The biomass concentration in
the mixed culture of the oleaginous yeast with microalgae increased
faster and was higher compared with that in the monocultures. A
biomass of 8.733g/L with lipid yield of 1.564g/L was obtained for a
mixed culture of T. maleeae Y30 with Chlorella sp. KKU-S2, while
8.010g/L of biomass with lipid yield of 2.424g/L was found for
mixed culture of T. globosa YU5/2 with Chlorella sp. KKU-S2.
Maximum cell yield coefficient (YX/S, g/L) was found of 0.323 in
monoculture of Chlorella sp. KKU-S2 but low level of both specific
yield of lipid (YP/X, g lipid/g cells) of 0.027 and volumetric lipid
production rate (QP, g/L/d) of 0.003 were observed. While, maximum
YP/X (0.303), QP (0.105) and maximum process product yield (YP/S,
0.061) were obtained in mixed culture of T. globosa YU5/2 with
Chlorella sp. KKU-S2. The results obtained from the study shows
that mixed culture of yeast with microalgae is a desirable cultivation
process for microbial oil production.
Abstract: The mechanism behind the electromigration and
thermomigration failure in flip-chip solder joints with Cu-pillar bumps
was investigated in this paper through using finite element method.
Hot spot and the current crowding occurrs in the upper corner of
copper column instead of solders of the common solder ball. The
simulation results show that the change in thermal gradient is
noticeable, which might greatly affect the reliability of solder joints
with Cu-pillar bumps under current stressing. When the average
applied current density is increased from 1×104 A/cm2 to 3×104 A/cm2
in solders, the thermal gradient would increase from 74 K/cm to 901
K/cm at an ambient temperature of 25°C. The force from thermal
gradient of 901 K/cm can nearly induce thermomigration by itself.
With the increase in applied current, the thermal gradient is growing. It
is proposed that thermomigration likely causes a serious reliability
issue for Cu column based interconnects.
Abstract: Mobile Ad Hoc network is an infrastructure less
network which operates with the coordination of each node. Each node
believes to help another node, by forwarding its data to/from another
node. Unlike a wired network, nodes in an ad hoc network are resource
(i.e. battery, bandwidth computational capability and so on)
constrained. Such dependability of one node to another and limited
resources of nodes can result in non cooperation by any node to
accumulate its resources. Such non cooperation is known as selfish
behavior.
This paper discusses the performance analysis of very well known
MANET single-path (i.e. AODV) and multi-path (i.e. AOMDV)
routing protocol, in the presence of selfish behaviors. Along with
existing selfish behaviors, a new variation is also studied. Extensive
simulations were carried out using ns-2 and the study concluded that
the multi-path protocol (i.e. AOMDV) with link disjoint configuration
outperforms the other two configurations.
Abstract: This paper describes the design considerations of an
experimental setup for research and exploring the drives of batteryfed
electric vehicles. Effective setup composition and its components
are discussed. With experimental setup described in this paper,
durability and functional tests can be procured to the customers.
Multiple experiments are performed in the form of steady-state
system exploring, acceleration programs, multi-step tests (speed
control, torque control), load collectives or close-to-reality driving
tests (driving simulation). Main focus of the functional testing is on
the measurements of power and energy efficiency and investigations
in driving simulation mode, which are used for application purposes.
In order to enable the examination of the drive trains beyond
standard modes of operation, different other parameters can be
studied also.