Abstract: High performance turf reinforcement mat (HPTRM) is
one of the most advanced flexible armoring technologies for severe
erosion challenges. The effect of turbulence on the slope stability of
an earthen levee strengthened by high performance turf reinforcement
mat (HPTRM) is investigated in this study for combined storm surge
and wave overtopping conditions. The results show that turbulence
has strong influence on the slope stability during the combined storm
surge and wave overtopping conditions. Among the surge height,
peak wave force and turbulent force. The turbulent force has the
ability to stabilize the earthen levee at the large wave force the
turbulent force has strongest effect on the FS. The surge storm acts as
an independent force on the slope stability of the earthen levee. It just
adds to the effects of the turbulent force and wave force on the slope
stability of HPTRM strengthened levee.
Abstract: This paper presents a study of SIW circuits (Substrate
Integrated Waveguide) with a rigorous and fast original approach
based on Iterative process (WCIP). The theoretical suggested study is
validated by the simulation of two different examples of SIW
circuits. The obtained results are in good agreement with those of
measurement and with software HFSS.
Abstract: This paper presents effects of distilled water, seawater
and sustained bending strains of 30% and 50% ultimate strain at
room temperature, on the durability of unidirectional pultruded
carbon fiber reinforced polymer (CFRP) plates. In this study,
dynamic mechanical analyzer (DMA) was used to investigate the
synergic effects of the immersions and bending strains on the viscoelastic
properties of (CFRP) such as storage modulus, tan delta and
glass transition temperature. The study reveals that the storage
modulus and glass transition temperature increase while tan delta
peak decreases in the initial stage of both immersions due to the
progression of curing. The storage modulus and Tg subsequently
decrease and tan delta increases due to the matrix plasticization. The
blister induced damages in the unstrained seawater samples enhance
water uptake and cause more serious degradation of Tg and storage
modulus than in water immersion. Increasing sustained bending
decreases Tg and storage modulus in a long run for both immersions
due to resin matrix cracking and debonding. The combined effects of
immersions and strains are not clearly reflected due to the statistical
effects of DMA sample sizes and competing processes of molecular
reorientation and postcuring.
Abstract: It is well known that in recent years magnetic
materials have received increased attention due to their properties.
For this reason a significant number of patents that were published
during the last decade are oriented towards synthesis and study of
such materials. The aim of this work is to create and study ferrite
nanocrystalline materials with spinel structure, using sol-gel
technology with participation of auto-combustion. This method is
perspective in that it is a cheap and low-temperature technique that
allows for the fine control on the product’s chemical composition.
Abstract: Image segmentation plays an important role in
medical imaging applications. Therefore, accurate methods are
needed for the successful segmentation of medical images for
diagnosis and detection of various diseases. In this paper, we have
used maximum entropy to achieve image segmentation. Maximum
entropy has been calculated using Shannon, Renyi and Tsallis
entropies. This work has novelty based on the detection of skin lesion
caused by the bite of a parasite called Sand Fly causing the disease is
called Cutaneous Leishmaniasis.
Abstract: The biodegradable family of polymers
polyhydroxyalkanoates is an interesting substitute for convectional
fossil-based plastics. However, the manufacturing and environmental
impacts associated with their production via intracellular bacterial
fermentation are strongly dependent on the raw material used and on
energy consumption during the extraction process, limiting their
potential for commercialization. Industrial wastewater is studied in
this paper as a promising alternative feedstock for waste valorization.
Based on results from laboratory and pilot-scale experiments, a
conceptual process design, techno-economic analysis and life cycle
assessment are developed for the large-scale production of the most
common type of polyhydroxyalkanoate, polyhydroxbutyrate.
Intracellular polyhydroxybutyrate is obtained via fermentation of
microbial community present in industrial wastewater and the
downstream processing is based on chemical digestion with
surfactant and hypochlorite. The economic potential and
environmental performance results help identifying bottlenecks and
best opportunities to scale-up the process prior to industrial
implementation. The outcome of this research indicates that the
fermentation of wastewater towards PHB presents advantages
compared to traditional PHAs production from sugars because the
null environmental burdens and financial costs of the raw material in
the bioplastic production process. Nevertheless, process optimization
is still required to compete with the petrochemicals counterparts.
Abstract: This paper describes the issues relating to the role of
the flash flood early warning system provided by the Malaysian
Government to the communities in Malaysia, specifically during the
flash flood disaster in the Cameron Highlands, Malaysia. Normally,
flash flood disasters can occur as a result of heavy rainfall in an area,
and that water may possibly cause flooding via streams or narrow
channels. The focus of this study is the flash flood disaster which
occurred on 23 October 2013 in the Cameron Highlands, and as a
result the Sungai Bertam overflowed after the release of water from
the Sultan Abu Bakar Dam. This release of water from the dam
caused flash flooding which led to damage to properties and also the
death of residents and livestock in the area. Therefore, the effort of
this study is to identify the perceptions of the flash flood victims on
the role of the flash flood early warning system. For the purposes of
this study, data were gathered through face-to-face interviews from
those flood victims who were willing to participate in this study. This
approach helped the researcher to glean in-depth information about
their feelings and perceptions of the role of the flash flood early
warning system offered by the government. The data were analysed
descriptively and the findings show that the respondents of 22 flood
victims believe strongly that the flash flood early warning system was
confusing and dysfunctional, and communities had failed to response
positively to it. Therefore, most of the communities were not well
prepared for the releasing of water from the dam which caused
property damage, and 3 people were killed in the Cameron Highland
flash flood disaster.
Abstract: Specific leaf area (SLA; cm2leaf g-1leaf) the ratio of leaf
area to leaf dry mass is a key ecophysiological parameter influencing
leaf physiology, photosynthesis, and whole plant carbon gain and
also can be used as a rapid and diagnostic tool. In this study, two
species of soluble inorganic selenium forms, selenite (Se^IV) and
selenate (Se^VI) at different concentrations were investigated on maize
plants that were growing in nutrient solutions during 2 weeks and at
the end of the experiment, amounts of SLA for first and second
leaves of maize were measured. In accordance with the results we
observed that our regarded Se concentrations in both forms of Se^IV
and Se^VI were not effective on maize plants’ SLA significantly
although high level of 3 mg.kg-1 Se^IV had negative affect on growth
of the samples that had been treated by it but about Se^VI samples we
did not observe this state and our different considered Se^VI
concentrations were not toxic for maize plants.
Abstract: The paper discusses mineral water consumer market
and development policy in Georgia, the tools and measures, which
will contribute to production of mineral waters and increase its
export.
The paper studies and analyses current situation in mineral water
production sector as well as the factors affecting increase and
reduction of its export. It’s noted that in order to gain and maintain
competitive advantage, it’s necessary to provide continuous supply of
high quality goods with modern design, open new distribution
channels to enter new markets, carry out broad promotional activities,
organize e-commerce. Economic policy plays an important role in
protecting markets from counterfeit goods. The state also plays an
important role in attracting foreign direct investments. Stable
business environment and export oriented strategy is the basis for the
country’s economic growth.
Based on the research, the paper suggests the strategy for
improving competitiveness of Georgian mineral waters; relevant
conclusions and recommendations are provided.
Abstract: This article discusses event monitoring options for
heterogeneous event sources as they are given in nowadays
heterogeneous distributed information systems. It follows the central
assumption, that a fully generic event monitoring solution cannot
provide complete support for event monitoring; instead, event source
specific semantics such as certain event types or support for certain
event monitoring techniques have to be taken into account.
Following from this, the core result of the work presented here is
the extension of a configurable event monitoring (Web) service for a
variety of event sources. A service approach allows us to trade
genericity for the exploitation of source specific characteristics. It
thus delivers results for the areas of SOA, Web services, CEP and
EDA.
Abstract: In this study, polycaprolactone (PCL) was dissolved
in chloroform:ethanol solvent system at a concentration of 18 w/v %.
1, 2, 4, and 6 droplets of formic acid were added to the prepared 10ml
PCL-chloroform:ethanol solutions separately. Fibrous webs were
produced by electrospinning technique based on the horizontal
working principle. Morphology of the webs was investigated by
using scanning electron microscopy (SEM) whereas fiber diameters
were measured by Image J Software System. The effect of formic
acid addition to the mostly used chloroform solvent on fiber
morphology was examined.
Results indicate that there is a distinct fall in fiber diameter with
the addition of formic acid drops. The average fiber diameter was
measured as 2.22μm in PCL /chloroform:ethanol solution system. On
the other hand, 328nm and 256 nm average fiber diameters were
measured for the samples of 4 drops and 6 drops formic acid added.
This study offers alternative solvent systems to produce nanoscaled,
nontoxic PCL fibrous webs by electrospinning technique.
Abstract: Problems insulation of building structures is often
closely connected with the problem of moisture remediation. In the
case of historic buildings or if only part of the redevelopment of
envelope of structures, it is not possible to apply the classical external
thermal insulation composite systems. This application is mostly
effective thermal insulation plasters with high porosity and controlled
capillary properties which assures improvement of thermal properties
construction, its diffusion openness towards the external environment
and suitable treatment capillary properties of preventing the
penetration of liquid moisture and salts thereof toward the outer
surface of the structure.
With respect to the current trend of reducing the energy
consumption of building structures and reduce the production of CO2
is necessary to develop capillary-active materials characterized by
their low density, low thermal conductivity while maintaining good
mechanical properties. The aim of researchers at the Faculty of Civil
Engineering, Brno University of Technology is the development and
study of hygrothermal behaviour of optimal materials for thermal
insulation and rehabilitation of building structures with the possible
use of alternative, less energy demanding binders in comparison with
conventional, frequently used binder, which represents cement.
The paper describes the evaluation of research activities aimed at
the development of thermal insulation and repair materials using
lightweight aggregate and alternative binders such as metakaolin and
finely ground fly ash.
Abstract: In medical investigations, uncertainty is a major
challenging problem in making decision for doctors/experts to
identify the diseases with a common set of symptoms and also has
been extensively increasing in medical diagnosis problems. The
theory of cross entropy for intuitionistic fuzzy sets (IFS) is an
effective approach in coping uncertainty in decision making for
medical diagnosis problem. The main focus of this paper is to
propose a new intuitionistic fuzzy cross entropy measure (IFCEM),
which aid in reducing the uncertainty and doctors/experts will take
their decision easily in context of patient’s disease. It is shown that
the proposed measure has some elegant properties, which
demonstrates its potency. Further, it is also exemplified in detail the
efficiency and utility of the proposed measure by using a real life
case study of diagnosis the disease in medical science.
Abstract: Poly bag and mulch films for agricultural field caused
pose environmental problem due to the non-degradable plastics
wastes upon disposal. Thus, a degradable poly bag was designed with
hybrid sago starch (SS) and polyvinyl alcohol (PVA). Two Different
blended compositions of SS and PVA hybrid have been compounded.
Then, the hybrids blended are mixed with linear line density
polyethylene (LLDPE) resin to fabricate poly bag film through
conventional film blowing process. Samples of LLDPE, SS and PVA
hybrid film were exposed to UV light and soil burial. The weight
losses were determined during degradation process. Hybrid film by
degradation of starch was found to hydrolyze and hydroxyl groups
decrease on esterification upon exposure to soil burial and uv
radiation. It was found out that, the hybrid film for 60% of SS
composition showed greatest degradation in soil and UV radiation.
Abstract: Freshly laid eggs from green turtles, Chelonia mydas,
were randomly collected from Ras Al-Hadd Reserve, Oman.
Eggshells taken from eggs and sand collected from the body chamber
were analyzed for eight heavy metals (Al, Br, Cd, Co, Cu, Fe, S, and
Zn) using inductively coupled plasma mass spectrometry (ICP).
Heavy metal concentrations varied significantly (P
Abstract: The objective of this work is to study the effect of two
key factors - external magnetic field and applied current density
during template-based electrodeposition of nickel nanowires using an
electrode distance of 20 mm. Morphology, length, crystallite size and
crystallographic characterization of the grown nickel nanowires at an
electrode distance of 20mm are presented. For this electrode distance
of 20 mm, these two key electrodeposition factors when coupled was
found to reduce crystallite size with a higher growth length and
preferred orientation of Ni crystals. These observed changes can be
inferred to be due to coupled interaction forces induced by the
intensity of applied electric field (current density) and external
magnetic field known as magnetohydrodynamic (MHD) effect during
the electrodeposition process.
Abstract: This study was conducted Razakı grape variety (Vitis
vinifera L.) and its vine which was aged 19 was grown on 5 BB
rootstock in a vegetation period of 2014 in Afyon province in Turkey.
In this research, it was investigated whether the applications of
Control (C), 1/3 Cluster Tip Reduction (1/3 CTR), Shoot Tip
Reduction (STR), 1/3 CTR + STR, Boric Acid (BA), 1/3 CTR + BA,
STR + BA, 1/3 CTR + STR + BA on yield and yield components of
Razakı grape variety. The results were obtained as the highest fresh
grape yield (7.74 kg/vine) with C application; as the highest cluster
weight (244.62 g) with STR application; as the highest 100 berry
weight (504.08 g) with C application; as the highest maturity index
(36.89) with BA application; as the highest must yield (695.00 ml)
with BA and (695.00 ml) with 1/3 CTR + STR + BA applications; as
the highest intensity of L* color (46.93) with STR and (46.10) with
1/3 CTR + STR + BA applications; as the highest intensity of a*
color (-5.37) with 1/3 CTR + STR and (-5.01) with STR, as the
highest intensity of b* color (12.59) with STR application. The shoot
tip reduction to increase cluster weight and boric acid application to
increase maturity index of Razakı grape variety can be recommended.
Abstract: The introduction of degradable plastic materials into
agricultural sectors has represented a promising alternative to
promote green agriculture and environmental friendly of modern
farming practices. Major challenges of developing degradable
agricultural films are to identify the most feasible types of
degradation mechanisms, composition of degradable polymers and
related processing techniques. The incorrect choice of degradable
mechanisms to be applied during the degradation process will cause
premature losses of mechanical performance and strength. In order to
achieve controlled process of agricultural film degradation, the
compositions of degradable agricultural film also important in order
to stimulate degradation reaction at required interval of time and to
achieve sustainability of the modern agricultural practices. A set of
photodegradable polyethylene based agricultural film was developed
and produced, following the selective optimization of processing
parameters of the agricultural film manufacturing system. Example of
agricultural films application for oil palm seedlings cultivation is
presented.
Abstract: Phelipanche ramosa is the most damaging obligate
flowering parasitic weed on wide species of cultivated plants. The
semi-arid regions of the world are considered the main centers of this
parasitic plant that causes heavy infestation. This is due to its
production of high numbers of seeds (up to 200,000) that remain
viable for extended periods (up to 20 years). In this study, 13
treatments for the control of Phelipanche were carried out, which
included agronomic, chemical, and biological treatments and the use
of resistant plant methods. In 2014, a trial was performed at the
Department of Agriculture, Food and Environment, University of
Foggia (southern Italy), on processing tomato (cv ‘Docet’) grown in
pots filled with soil taken from a field that was heavily infested by P.
ramosa). The tomato seedlings were transplanted on May 8, 2014,
into a sandy-clay soil (USDA). A randomized block design with 3
replicates (pots) was adopted. During the growing cycle of the
tomato, at 70, 75, 81 and 88 days after transplantation, the number of
P. ramosa shoots emerged in each pot was determined. The tomato
fruit were harvested on August 8, 2014, and the quantitative and
qualitative parameters were determined. All of the data were
subjected to analysis of variance (ANOVA) using the JMP software
(SAS Institute Inc. Cary, NC, USA), and for comparisons of means
(Tukey's tests). The data show that each treatment studied did not
provide complete control against P. ramosa. However, the virulence
of the attacks was mitigated by some of the treatments tried: radicon
biostimulant, compost activated with Fusarium, mineral fertilizer
nitrogen, sulfur, enzone, and the resistant tomato genotype. It is
assumed that these effects can be improved by combining some of
these treatments with each other, especially for a gradual and
continuing reduction of the “seed bank” of the parasite in the soil.
Abstract: The hydrodynamics and heat transfer characteristics
of a vaporized elongated bubble in a rectangular microchannel have
been simulated based on Cahn-Hilliard phase-field method. In the
simulations, the initially nucleated bubble starts growing as it comes
in contact with superheated water. The growing shape of the bubble
compared well with the available experimental data in the literature.