Abstract: Ceramic obtained on the base of aluminum oxide has
wide application range, because it has unique properties, for example,
wear-resistance, dielectric characteristics, and exploitation ability at
high temperatures and in corrosive atmosphere. Low temperature
synthesis of α-Al2O3 is energo-economical process and it is topical
for developing technologies of corundum ceramics fabrication. In the present work possibilities of low temperature transformation
of oxyhydroxides in α-Al2O3, during the presence of small amount of
rare–earth elements compounds (also Th, Re), have been discussed.
Aluminum unstable oxyhydroxides have been obtained by hydrolysis
of aluminium isopropoxide, nitrates, sulphate, and chloride in
alkaline environment at 80-90ºC temperatures. β-Al(OH)3 has been
received from aluminum powder by ultrasonic development. Drying
of oxyhydroxide sol has been conducted with presence of various
types seeds, which amount reaches 0,1-0,2% (mas). Neodymium,
holmium, thorium, lanthanum, cerium, gadolinium, disprosium
nitrates and rhenium carbonyls have been used as seeds and they
have been added to the sol specimens in amount of 0.1-0.2% (mas)
calculated on metals. Annealing of obtained gels is carried out at 70–
1100ºC for 2 hrs. The same specimen transforms in α-Al2O3 at
1100ºC. At this temperature in case of presence of lanthanum and
gadolinium transformation takes place by 70-85%. In case of
presence of thorium stabilization of γ-and θ-phases takes place. It is
established, that thorium causes inhibition of α-phase generation at
1100ºC, and at the time when in all other doped specimens α-phase is
generated at lower temperatures (1000-1050ºC). Synthesis of various
type compounds and simultaneous consolidation has developed in the
furnace of OXY-GON. Composite materials containing oxide and
non-oxide components close to theoretical data have been obtained in
this furnace respectively. During the work the following devices have
been used: X-ray diffractometer DRON-3M (Cu-Kα, Ni filter,
2º/min), High temperature vacuum furnace OXY-GON, electronic
scanning microscopes Nikon ECLIPSE LV 150, NMM-800TRF,
planetary mill Pulverisette 7 premium line, SHIMADZU Dynamic
Ultra Micro Hardness Tester, DUH-211S, Analysette 12 Dyna sizer.
Abstract: An experimental study with four different types of bed
conditions was carried out to understand the effect of roughness in
open channel flow at two different Reynolds numbers. The bed
conditions include a smooth surface and three different roughness
conditions, which were generated using sand grains with a median
diameter of 2.46 mm. The three rough conditions include a surface
with distributed roughness, a surface with continuously distributed
roughness and a sand bed with a permeable interface. A commercial
two-component fibre-optic LDA system was used to conduct the
velocity measurements. The variables of interest include the mean
velocity, turbulence intensity, correlation between the streamwise and
the wall normal turbulence, Reynolds shear stress and velocity triple
products. Quadrant decomposition was used to extract the magnitude
of the Reynolds shear stress of the turbulent bursting events. The
effect of roughness was evident throughout the flow depth. The
results show that distributed roughness has the greatest roughness
effect followed by the sand bed and the continuous roughness.
Compared to the smooth bed, the streamwise turbulence intensity
reduces but the vertical turbulence intensity increases at a location
very close to the bed due to the introduction of roughness. Although
the same sand grain is used to create the three different rough bed
conditions, the difference in the turbulence intensity is an indication
that the specific geometry of the roughness has an influence on
turbulence structure.
Abstract: Construction industry plays a vital role in the
economy of the world. However, due to high uncertainty and
variability in the industry, its performance is not as efficient in terms
of quality, lead times, productivity and costs as of other industries.
Moreover, there are continuous conflicts among the different actors
in the construction supply chains in terms of profit sharing. Previous
studies suggested partnership as an important approach to promote
cooperation among the different actors in the construction supply
chains and thereby it improves the overall performance. Construction
practitioners tried to focus on partnership which can enhance the
performance of construction supply chains but they are not fully
aware of different approaches and techniques for improving
partnership. In this research, a systematic review on partnership in
relation to construction supply chains is carried out to understand
different elements influencing the partnership. The research
development of this domain is analyzed by reviewing selected
articles published from 1996 to 2015. Based on the papers, three
major elements influencing partnership in construction supply chains
are identified: ‘Lean approach’, ‘Relationship building’ and ‘E-commerce
applications’. This study analyses the contributions in the
areas within each element and provides suggestions for future
developments of partnership in construction supply chains.
Abstract: Financial inclusion has become a crucially important
factor in debates on economic inequality posing challenges to the
financial systems of countries around the world. Nowadays
governments and banks are concerned about creating products that
allow access to wide sectors of the population. The creation of
banking products by the financial sector for people with low incomes
tends to lead to improvements in the quality of life of vulnerable parts
of the population. In countries with notable social and economic
inequalities, financial inclusion is a key aspect for equitable
economic growth. This study is based on the case of Colombia, which is a country
with a strong record of economic growth over the past decade.
Nevertheless, corruption, unemployment, and poverty contribute to
uncertainty regarding the country’s future growth prospects. This study wants to explain the situation of financial exclusion and
financial inclusion with respect to the Colombian case. Financial
inclusion is going to be studied from the perspective of social
innovation.
Abstract: The Radio Frequency Identification (RFID) technology
has a diverse base of applications, but it is also prone to security
threats. There are different types of security attacks which limit the
range of the RFID applications. For example, deploying the RFID
networks in insecure environments could make the RFID system
vulnerable to many types of attacks such as spoofing attack, location
traceability attack, physical attack and many more. Therefore, security
is often an important requirement for RFID systems. In this paper,
RFID mutual authentication protocol is implemented based on mobile
agent technology and timestamp, which are used to provide strong
authentication and integrity assurances to both the RFID readers and
their corresponding RFID tags. The integration of mobile agent
technology and timestamp provides promising results towards
achieving this goal and towards reducing the security threats in RFID
systems.
Abstract: This paper describes a subarray based low
computational design method of multiuser massive multiple
input multiple output (MIMO) system. In our previous works, use of
large array is assumed only in transmitter, but this study considers
the case both of transmitter and receiver sides are equipped with
large array antennas. For this aim, receive arrays are also divided
into several subarrays, and the former proposed method is modified
for the synthesis of a large array from subarrays in both ends.
Through computer simulations, it is verified that the performance
of the proposed method is degraded compared with the original
approach, but it can achieve the improvement in the aspect of
complexity, namely, significant reduction of the computational load
to the practical level.
Abstract: Recently, numerous documents including large
volumes of unstructured data and text have been created because of the
rapid increase in the use of social media and the Internet. Usually,
these documents are categorized for the convenience of users. Because
the accuracy of manual categorization is not guaranteed, and such
categorization requires a large amount of time and incurs huge costs.
Many studies on automatic categorization have been conducted to help
mitigate the limitations of manual categorization. Unfortunately, most
of these methods cannot be applied to categorize complex documents
with multiple topics because they work on the assumption that
individual documents can be categorized into single categories only.
Therefore, to overcome this limitation, some studies have attempted to
categorize each document into multiple categories. However, the
learning process employed in these studies involves training using a
multi-categorized document set. These methods therefore cannot be
applied to the multi-categorization of most documents unless
multi-categorized training sets using traditional multi-categorization
algorithms are provided. To overcome this limitation, in this study, we
review our novel methodology for extending the category of a
single-categorized document to multiple categorizes, and then
introduce a survey-based verification scenario for estimating the
accuracy of our automatic categorization methodology.
Abstract: The influence of Islam on arts can be found primarily
in calligraphy, arabesque designs and architecture. Also, geometric
designs were used quite extensively. Muslim craftsmen produced
stunning designs based on simple geometric principles and traditional
motifs which were used to decorate many surfaces. The idea of
interlacing simple rectilinear lines to form the patterns impressed
Arabs. Nomads of Persia, Turks and Mongols were equally
impressed with the designs so they begin to use them in their homes
in carpet weaving. Islamic designs, motifs and colours which were
used became common place and served to influence people’s tastes.
Modern life style and contemporary products have changed the style
of people’s daily lives, however, people still long for the nomadic
way of life. This is clearly reflected in people’s homes. In a great
many Muslim homes, Islamic decorative motifs can be seen along
with traditional ‘Bedouin’ style furnishing, especially in homes of the
Arabian Peninsula.
Abstract: Evaluation of the excavation-induced ground
movements is an important design aspect of support systems in urban
areas. Geological and geotechnical conditions of an excavation area
have significant effects on excavation-induced ground movements and
the related damage. This paper is aimed at studying the performance of
excavation walls supported by nails in jointed rock medium. The
performance of nailed walls is investigated based on evaluating the
excavation-induced ground movements. For this purpose, a set of
calibrated 2D finite element models are developed by taking into
account the nail-rock-structure interactions, the anisotropic properties
of jointed rock, and the staged construction process. The results of this
paper highlight effects of different parameters such as joint
inclinations, anisotropy of rocks and nail inclinations on deformation
parameters of excavation wall supported by nails.
Abstract: An analytical 4-DOF nonlinear model of a de Laval
rotor-stator system based on Energy Principles has been used
theoretically and experimentally to investigate fault symptoms in a
rotating system. The faults, namely rotor-stator-rub, crack and
unbalance are modeled as excitations on the rotor shaft. Mayes
steering function is used to simulate the breathing behaviour of the
crack. The fault analysis technique is based on waveform signal,
orbits and Fast Fourier Transform (FFT) derived from simulated and
real measured signals. Simulated and experimental results manifest
considerable mutual resemblance of elliptic-shaped orbits and FFT
for a same range of test data.
Abstract: The hydrodynamic and thermal behaviors of fluid
flow in wavy microchannel are investigated numerically. Effects of
Reynolds number on the hydrodynamics and thermal behaviors are
investigated. Three cases of Reynolds number (580, 1244, and 1910)
are adopted in this study. It is found that the separation zone begin
appears when Reynolds number is greater than 1910 at the endsection
of the wave. Also it is found that dimensionless maximum
velocity at the mid-section of the wave decreases and becomes as a
turbulent behavior as Reynolds numbers increases. The maximum
temperature at the center line at the mid-section of the wave increases
as Reynolds number increases until it reaches the turbulent behavior
when Reynolds number is equal or greater than 1244, while this
behavior will be achieved at very high velocities at the end section of
the wave.
Abstract: Si-Ge solid solutions (bulk poly- and mono-crystalline
samples, thin films) are characterized by high perspectives for
application in semiconductor devices, in particular, optoelectronics
and microelectronics. From this point of view, complex studying of
structural state of the defects and structural-sensitive physical
properties of Si-Ge solid solutions depending on the contents of Si
and Ge components is very important. Present work deals with the
investigations of microstructure, microhardness, internal friction and
shear modulus of Si1-xGex(x≤0,02) bulk monocrystals conducted at
room temperature. Si-Ge bulk crystals were obtained by Czochralski
method in [111] crystallographic direction. Investigated
monocrystalline Si-Ge samples are characterized by p-type
conductivity and carriers’ concentration 5.1014-1.1015cm-3.
Microhardness was studied on Dynamic Ultra Micro hardness Tester
DUH-201S with Berkovich indenter. Investigate samples are characterized with 0,5x0,5x(10-15)mm3
sizes, oriented along [111] direction at torsion oscillations ≈1Hz,
multistage changing of internal friction and shear modulus has been
revealed in an interval of strain amplitude of 10-5-5.10-3. Critical
values of strain amplitude have been determined at which hysteretic
changes of inelastic characteristics and microplasticity are observed. The critical strain amplitude and elasticity limit values are also
determined. Dynamic mechanical characteristics decreasing trend is
shown with increasing Ge content in Si-Ge solid solutions. Observed
changes are discussed from the point of view of interaction of various
dislocations with point defects and their complexes in a real structure
of Si-Ge solid solutions.
Abstract: The need to merge software artifacts seems inherent
to modern software development. Distribution of development over
several teams and breaking tasks into smaller, more manageable
pieces are an effective means to deal with the kind of complexity. In
each case, the separately developed artifacts need to be assembled as
efficiently as possible into a consistent whole in which the parts still
function as described. In addition, earlier changes are introduced into
the life cycle and easier is their management by designers.
Interaction-based specifications such as UML sequence diagrams
have been found effective in this regard. As a result, sequence
diagrams can be used not only for capturing system behaviors but
also for merging changes in order to create a new version. The
objective of this paper is to suggest a new approach to deal with the
problem of software merging at the level of sequence diagrams by
using the concept of dependence analysis that captures, formally, all
mapping, and differences between elements of sequence diagrams
and serves as a key concept to create a new version of sequence
diagram.
Abstract: In this paper, we present a comparative study of three
methods of 2D face recognition system such as: Iso-Geodesic Curves
(IGC), Geodesic Distance (GD) and Geodesic-Intensity Histogram
(GIH). These approaches are based on computing of geodesic
distance between points of facial surface and between facial curves.
In this study we represented the image at gray level as a 2D surface in
a 3D space, with the third coordinate proportional to the intensity
values of pixels. In the classifying step, we use: Neural Networks
(NN), K-Nearest Neighbor (KNN) and Support Vector Machines
(SVM). The images used in our experiments are from two wellknown
databases of face images ORL and YaleB. ORL data base was
used to evaluate the performance of methods under conditions where
the pose and sample size are varied, and the database YaleB was used
to examine the performance of the systems when the facial
expressions and lighting are varied.
Abstract: Heart is the most important part in the body of living
organisms. It affects and is affected by any factor in the body.
Therefore, it is a good detector for all conditions in the body. Heart
signal is a non-stationary signal; thus, it is utmost important to study
the variability of heart signal. The Heart Rate Variability (HRV) has
attracted considerable attention in psychology, medicine and has
become important dependent measure in psychophysiology and
behavioral medicine. The standards of measurements, physiological
interpretation and clinical use for HRV that are most often used were
described in many researcher papers, however, remain complex
issues are fraught with pitfalls. This paper presents one of the nonlinear
techniques to analyze HRV. It discusses many points like, what
Poincaré plot is and how Poincaré plot works; also, Poincaré plot's
merits especially in HRV. Besides, it discusses the limitation of
Poincaré cause of standard deviation SD1, SD2 and how to overcome
this limitation by using complex correlation measure (CCM). The
CCM is most sensitive to changes in temporal structure of the
Poincaré plot as compared toSD1 and SD2.
Abstract: This research was conducted in an automotive company in Indonesia to overcome the problem of high logistics cost. The problem causes high of additional truck delivery. From the breakdown of the problem, chosen one route, which has the highest gap value, namely for RE-04. Research methodology will be started from calculating the ideal condition, making simulation, calculating the ideal logistic cost, and proposing an improvement. From the calculation of the ideal condition, box arrangement was done on the truck has efficiency with three trucks delivery per day. Route simulation making uses Tecnomatix Plant Simulation software as a visualization for the company about how the system is occurred on route RE-04 in ideal condition. The last step is proposing improvements on the area of route RE-04. The route arrangement is done by Saving Method and sequence of each supplier with the Nearest Neighbor. The results of the proposed improvements are three new route groups, where was expected to decrease logistics cost and increase the average of the truck efficiency per day.
Abstract: This paper aims to determine Fundamental Natural
Frequency (FNF) of a structural composite floor system known as
Chromite. To achieve this purpose, FNFs of studied panels are
determined by development of Finite Element Models (FEMs) in
ABAQUS program. American Institute of Steel Construction (AISC)
code in Steel Design Guide Series 11 presents a fundamental formula
to calculate FNF of a steel framed floor system. This formula has
been used to verify results of the FEMs. The variability in the FNF of
the studied system under various parameters such as dimensions of
floor, boundary conditions, rigidity of main and secondary beams
around the floor, thickness of concrete slab, height of composite
joists, distance between composite joists, thickness of top and bottom
flanges of the open web steel joists, and adding tie beam
perpendicular on the composite joists, is determined. The results
show that changing in dimensions of the system, its boundary
conditions, rigidity of main beam, and also adding tie beam,
significant changes the FNF of the system up to 452.9%, 50.8%, -
52.2%, %52.6%, respectively. In addition, increasing thickness of
concrete slab increases the FNF of the system up to 10.8%.
Furthermore, the results demonstrate that variation in rigidity of
secondary beam, height of composite joist, and distance between
composite joists, and thickness of top and bottom flanges of open
web steel joists insignificant changes the FNF of the studied system
up to -0.02%, -3%, -6.1%, and 0.96%, respectively. Finally, the
results of this study help designer predict occurrence of resonance,
comfortableness, and design criteria of the studied system.
Abstract: The effect of molybdate addition to chloride
environment on resistance of AISI 316Ti stainless steel to pitting
corrosion was studied. Potentiodynamic polarisation tests were
performed in 1 M and 0.1 M chloride acidified solutions with various
additions of sodium molybdate at room temperature. The presented
results compare the effect of molybdate anions on quality of passive
film (expressed by the pitting potential) in both chloride solutions.
The pitting potential increases with the increase inhibitor
concentration. The inhibitive effect of molybdate ions is stronger in
chloride solution of lower aggressiveness (0.1M).
Abstract: This paper studies a mathematical model based on the
integral equations for dynamic analyzes numerical investigations of a
non-uniform or multi-material composite beam. The beam is
subjected to a sub-tangential follower force and elastic foundation.
The boundary conditions are represented by generalized
parameterized fixations by the linear and rotary springs. A
mathematical formula based on Euler-Bernoulli beam theory is
presented for beams with variable cross-sections. The non-uniform
section introduces non-uniformity in the rigidity and inertia of beams
and consequently, more complicated equilibrium who governs the
equation. Using the boundary element method and radial basis
functions, the equation of motion is reduced to an algebro-differential
system related to internal and boundary unknowns. A generalized
formula for the deflection, the slope, the moment and the shear force
are presented. The free vibration of non-uniform loaded beams is
formulated in a compact matrix form and all needed matrices are
explicitly given. The dynamic stability analysis of slender beam is
illustrated numerically based on the coalescence criterion. A realistic
case related to an industrial chimney is investigated.
Abstract: This paper presents comparative analysis of
photovoltaic systems (PVS) and propose practical techniques to
improve operational efficiency of the PVS. The best engineering and
construction practices for PVS are identified and field oriented
recommendation are made. Comparative analysis of central and
string inverter based, as well as 600 and 1000VDC PVS are
performed. In addition, direct current (DC) and alternating current
(AC) photovoltaic (PV) module based systems are compared.
Comparison shows that 1000V DC String Inverters based PVS is the
best choice.