Abstract: In this paper, a asymptotically periodic predator-prey
model with Modified Leslie-Gower and Holling-Type II schemes
is investigated. Some sufficient conditions for the uniformly strong
persistence of the system are established. Our result is an important
complementarity to the earlier results.
Abstract: This study presents a kinematic positioning approach
that uses a global positioning system (GPS) buoy for precise ocean
surface monitoring. The GPS buoy data from the two experiments are
processed using an accurate, medium-range differential kinematic
technique. In each case, the data from a nearby coastal site are
collected at a high rate (1 Hz) for more than 24 hours, and
measurements are conducted in neighboring tidal stations to verify
the estimated sea surface heights. The GPS buoy kinematic
coordinates are estimated using epoch-wise pre-elimination and a
backward substitution algorithm. Test results show that centimeterlevel
accuracy can be successfully achieved in determining sea
surface height using the proposed technique. The centimeter-level
agreement between the two methods also suggests the possibility of
using this inexpensive and more flexible GPS buoy equipment to
enhance (or even replace) current tidal gauge stations.
Abstract: The reheating furnace is used to reheat the steel slabs
before the hot-rolling process. The supported system includes the
stationary/moving beams, and the skid buttons which block some
thermal radiation transmitted to the bottom of the slabs. Therefore, it is
important to analyze the steel slab temperature distribution during the
heating period. A three-dimensional mathematical transient heat
transfer model for the prediction of temperature distribution within the
slab has been developed. The effects of different skid button height
(H=60mm, 90mm, and 120mm) and different gap distance between
two slabs (S=50mm, 75mm, and 100mm) on the slab skid mark
formation and temperature profiles are investigated. Comparison with
the in-situ experimental data from Steel Company in Taiwan shows
that the present heat transfer model works well for the prediction of
thermal behavior of the slab in the reheating furnace. It is found that
the skid mark severity decreases with an increase in the skid button
height. The effect of gap distance is important only for the slab edge
planes, while it is insignificant for the slab central planes.
Abstract: The aim of the performed work is to establish the 2D
and 3D model of direct unsteady task of sample heat treatment by
moving source employing computer model on the basis of finite
element method. Complex boundary condition on heat loaded sample
surface is the essential feature of the task. Computer model describes
heat treatment of the sample during heat source movement over the
sample surface. It is started from 2D task of sample cross section as a
basic model. Possibilities of extension from 2D to 3D task are
discussed. The effect of the addition of third model dimension on
temperature distribution in the sample is showed. Comparison of
various model parameters on the sample temperatures is observed.
Influence of heat source motion on the depth of material heat
treatment is shown for several velocities of the movement. Presented
computer model is prepared for the utilization in laser treatment of
machine parts.
Abstract: Automated Teller Machines (ATMs) can be
considered among one of the most important service facilities in the
banking industry. The investment in ATMs and the impact on the
banking industry is growing steadily in every part of the world. The
banks take into consideration many factors like safety, convenience,
visibility, and cost in order to determine the optimum locations of
ATMs. Today, ATMs are not only available in bank branches but
also at retail locations. Another important factor is the cash
management in ATMs. A cash demand model for every ATM is
needed in order to have an efficient cash management system. This
forecasting model is based on historical cash demand data which is
highly related to the ATMs location. So, the location and the cash
management problem should be considered together. This paper
provides a general review on studies, efforts and development in
ATMs location and cash management problem.
Abstract: This study aims at improving the urban hydrological
cycle of the Orléans agglomeration (France) and understanding the
relationship between physical and chemical parameters of urban
surface runoff and the hydrological conditions. In particular water
quality parameters such as pH, conductivity, total dissolved solids,
major dissolved cations and anions, and chemical and biological
oxygen demands were monitored for three types of urban water
discharges (wastewater treatment plant output (WWTP), storm
overflow and stormwater outfall) under two hydrologic scenarios (dry
and wet weather). The first results were obtained over a period of five
months. Each investigated (Ormes, l’Egoutier and La Corne) outfall
represents an urban runoff source that receives water from runoff
roads, gutters, the irrigation of gardens and other sources of flow over
the Earth’s surface that drains in its catchments and carries it to the
Loire River. In wet weather conditions there is rain water runoff and
an additional input from the roof gutters that have entered the
stormwater system during rainfall. For the comparison the results La
Chilesse is a storm overflow that was selected in our study as a
potential source of waste water which is located before the (WWTP). The comparison of the physical-chemical parameters (total
dissolved solids, turbidity, pH, conductivity, dissolved organic
carbon (DOC), concentration of major cations and anions) together
with the chemical oxygen demand (COD) and biological oxygen
demand (BOD) helped to characterize sources of runoff waters in the
different watersheds. It also helped to highlight the infiltration of
wastewater in some stormwater systems that reject directly in the
Loire River. The values of the conductivity measured in the outflow
of Ormes were always higher than those measured in the other two
outlets. The results showed a temporal variation for the Ormes outfall
of conductivity from 1465 μS cm-1 in the dry weather flow to 650 μS
cm-1 in the wet weather flow and also a spatial variation in the wet
weather flow from 650 μS cm-1 in the Ormes outfall to 281 μS cm-1
in L’Egouttier outfall. The ultimate BOD (BOD28) showed a
significant decrease in La Corne outfall from 181 mg L-1 in the wet
weather flow to 95 mg L-1 in the dry weather flow because of the
nutrient load that was transported by the runoff.
Abstract: With the increasing population and intensive land use,
huge traffic demand is generating worldwide both in developing and
developed countries. As a developing country, Bangladesh is also
facing the same problem in recent years by producing huge numbers
of daily trips. As a matter of fact, extensive traffic demand is
increasing day by day. Also, transport system in Dhaka is
heterogeneous, reflecting the heterogeneity in the socio-economic
and land use patterns. Trips produced here are for different purposes
such as work, business, educational etc. Due to the significant
concentration of educational institutions a large share of the trips are
generated by educational purpose. And one of the major percentages
of educational trips is produced by university going students and
most of them are travelled by car, bus, train, taxi, rickshaw etc. The
aim of the study was to find out the university students’ perception on
public transit ridership. A survey was conducted among 330 students
from eight different universities. It was found out that 26% of the
trips produced by university going students are travelled by public
bus service and only 5% are by train. Percentage of car share is 16%
and 12% of the trips are travelled by private taxi. It has been
observed from the study, students those who prefer bus instead of
other options, 42 percent of their family resides outside Dhaka. And
those who prefer walking, of them, over 40 percent students’ family
reside outside of Dhaka and of them over 85 percent students have a
tendency to live in a mess. On the contrary, students travelling by car
represents, most of their family reside in Dhaka. The study also
revealed that the most important reason that restricts students not to
use public transit is poor service. Negative attitudes such as
discomfort, uneasiness in using public transit also reduces the usage
of public transit. The poor waiting area is another major cause of not
using public transit. Insufficient security also plays a significant role
in not using public transit. On the contrary, the fare is not a problem
for students those who use public transit as a mode of transportation.
Students also think stations are not far away from their home or
institution and they do not need to wait long for the buses or trains. It
was also found accessibility to public transit is moderate.
Abstract: Growing human population has placed increased
demands on water supplies and spurred a heightened interest in
desalination infrastructure. Key elements of the economics of
desalination projects are thermal and electrical inputs. With growing
concerns over use of fossil fuels to (indirectly) supply these inputs,
coupling of desalination with nuclear power production represents a
significant opportunity. Individually, nuclear and desalination
technologies have a long history and are relatively mature. For
desalination, Reverse Osmosis (RO) has the lowest energy inputs.
However, the economically driven output quality of the water
produced using RO, which uses only electrical inputs, is lower than the
output water quality from thermal desalination plants. Therefore,
modern desalination projects consider that RO should be coupled with
thermal desalination technologies (MSF, MED, or MED-TVC) with
attendant steam inputs to permit blending to produce various qualities
of water. A large nuclear facility is well positioned to dispatch large
quantities of both electrical and thermal power. This paper considers
the supply of thermal energy to a large desalination facility to examine
heat balance impact on the nuclear steam cycle. The APR1400 nuclear
plant is selected as prototypical from both a capacity and turbine cycle
heat balance perspective to examine steam supply and the impact on
electrical output. Extraction points and quantities of steam are
considered parametrically along with various types of thermal
desalination technologies to form the basis for further evaluations of
economically optimal approaches to the interface of nuclear power
production with desalination projects. In our study, the
thermodynamic evaluation will be executed by DE-TOP, an IAEA
sponsored program. DE-TOP has capabilities to analyze power
generation systems coupled to desalination plants through various
steam extraction positions, taking into consideration the isolation loop
between the nuclear and the thermal desalination facilities (i.e., for
radiological isolation).
Abstract: The market competition is moving from the single
firm to the whole supply chain because of increasing competition and
growing need for operational efficiencies and customer orientation.
Supply chain management allows companies to look beyond their
organizational boundaries to develop and leverage resources and
capabilities of their supply chain partners. This creates competitive
advantages in the marketplace and because of this SCM has acquired
strategic importance. Lean Approach is a management strategy that focuses on reducing
every type of waste present in an organization. This approach is
becoming more and more popular among supply chain managers. The supply chain application of lean approach is not frequent. In
particular, it is not well studied which are the impacts of lean
approach principles in a supply chain context. In literature there are
only few studies aimed at understanding the qualitative impact of the
lean approach in supply chains. Therefore, the goal of this research
work is to study the impacts of lean principles implementation along
a supply chain. To achieve this, a simulation model of a threeechelon
multi-product supply chain has been built. Kanban system (and several priority policies) and setup time
reduction degrees are implemented in the lean-configured supply
chain to apply pull and lot-sizing decrease principles respectively. To
evaluate the benefits of lean approach, lean supply chain is compared
with an EOQ-configured supply chain. The simulation results show
that Kanban system and setup-time reduction improve inventory
stock level. They also show that logistics efforts are affected to lean
implementation degree. The paper concludes describing
performances of lean supply chain in different contexts.
Abstract: Zinc borate is an important inorganic hydrate borate
material, which can be used as a flame retardant agent and corrosion
resistance material. This compound can loss its structural water
content at higher than 290°C. Due to thermal stability; Zinc Borate
can be used as flame retardant at high temperature process of plastic
and gum. In this study, the ultrasonic reaction of zinc borates were
studied using hydrozincite (Zn5(CO3)2·(OH)6) and boric acid
(H3BO3) raw materials. Before the synthesis raw materials were
characterized by X-Ray Diffraction (XRD) and Fourier Transform
Infrared Spectroscopy (FT-IR). Ultrasonic method is a new
application on the zinc borate synthesis. The synthesis parameters
were set to 90°C reaction temperature and 55 minutes of reaction
time, with 1:1, 1:2, 1:3, 1:4 and 1:5 molar ratio of starting materials
(Zn5(CO3)2·(OH)6 : H3BO3). After the zinc borate synthesis, the
products were analyzed by XRD and FT-IR. As a result, optimum
molar ratio of 1:5 is determined for the synthesis of zinc borates with
ultrasonic method.
Abstract: Multiple Input Multiple Output (MIMO) systems are
wireless systems with multiple antenna elements at both ends of the
link. Wireless communication systems demand high data rate and
spectral efficiency with increased reliability. MIMO systems have
been popular techniques to achieve these goals because increased
data rate is possible through spatial multiplexing scheme and
diversity. Spatial Multiplexing (SM) is used to achieve higher
possible throughput than diversity. In this paper, we propose a Zero-
Forcing (ZF) detection using a combination of Ordered Successive
Interference Cancellation (OSIC) and Zero Forcing using
Interference Cancellation (ZF-IC). The proposed method used an
OSIC based on Signal to Noise Ratio (SNR) ordering to get the
estimation of last symbol, then the estimated last symbol is
considered to be an input to the ZF-IC. We analyze the Bit Error Rate
(BER) performance of the proposed MIMO system over Rayleigh
Fading Channel, using Binary Phase Shift Keying (BPSK)
modulation scheme. The results show better performance than the
previous methods.
Abstract: This work deals with the problem of MHD mixed
convection in a completely porous and differentially heated vertical
channel. The model of Darcy-Brinkman-Forchheimer with the
Boussinesq approximation is adopted and the governing equations are
solved by the finite volume method. The effects of magnetic field and
buoyancy force intensities are given by the Hartmann and Richardson
numbers respectively, as well as the Joule heating represented by
Eckert number on the velocity and temperature fields, are examined.
The main results show an augmentation of heat transfer rate with the
decrease of Darcy number and the increase of Ri and Ha when Joule
heating is neglected.
Abstract: The photovoltaic (PV) panel with no galvanic
isolation system is well known technique in the world which is
effective and delivers power with enhanced efficiency. The PV
generation presented here is for stand-alone system installed in
remote areas when as the resulting power gets connected to electronic
load installation instead of being tied to the grid. Though very small,
even then transformer-less topology is shown to be with leakage in
pico-ampere range. By using PWM technique PWM, leakage current
in different situations is shown. The results shown in this paper show
how the pico-ampere current is reduced to femto-ampere through use
of inductors and capacitors of suitable values of inductor and
capacitors with the load.
Abstract: Since the last decade, there has been a rapid growth in
digital multimedia, such as high-resolution media files and threedimentional
movies. Hence, there is a need for large digital storage
such as Hard Disk Drive (HDD). As such, users expect to have a
quieter HDD in their laptop. In this paper, a jury test has been
conducted on a group of 34 people where 17 of them are students
who are the potential consumer, and the remaining are engineers who
know the HDD. A total 13 HDD sound samples have been selected
from over hundred HDD noise recordings. These samples are
selected based on an agreed subjective feeling. The samples are
played to the participants using head acoustic playback system, which
enabled them to experience as similar as possible the same
environment as have been recorded. Analysis has been conducted and
the obtained results have indicated different group has different
perception over the noises. Two neural network-based acoustic
annoyance models are established based on back propagation neural
network. Four psychoacoustic metrics, loudness, sharpness,
roughness and fluctuation strength, are used as the input of the
model, and the subjective evaluation results are taken as the output.
The developed models are reasonably accurate in simulating both
training and test samples.
Abstract: This study and the field test comparisons were carried
out on the Algerian Derguna – Setif transmission systems. The
transmission line of normal voltage 225 kV is 65 km long,
transported and uses twin bundle conductors protected with two
shield wires of transposed galvanized steel. An iterative finite-element method is used to solve Poisons
equation. Two algorithms are proposed for satisfying the current
continuity condition and updating the space-charge density. A new approach to the problem of corona discharge in
transmission system has been described in this paper. The effect of
varying the configurations and wires number is also investigated. The
analysis of this steady is important in the design of HVDC
transmission lines. The potential and electric field have been
calculating in locations singular points of the system.
Abstract: An industrial system for the production of white
liquor of a paper industry, Klabin Paraná Papéis, formed by ten
reactors was modeled, simulated, and analyzed. The developed model
considered possible water losses by evaporation and reaction, in
addition to variations in volumetric flow of lime mud across the
reactors due to composition variations. The model predictions agreed
well with the process measurements at the plant and the results
showed that the slaking reaction is nearly complete at the third
causticizing reactor, while causticizing ends by the seventh reactor.
Water loss due to slaking reaction and evaporation occurs more
pronouncedly in the slaking reaction than in the final causticizing
reactors; nevertheless, the lime mud flow remains nearly constant
across the reactors.
Abstract: Cortisol is essential to the regulation of the immune
system and pathological yawning is a symptom of multiple sclerosis
(MS). Electromyography activity (EMG) in the jaw muscles typically
rises when the muscles are moved – extended or flexed; and yawning
has been shown to be highly correlated with cortisol levels in healthy
people as shown in the Thompson Cortisol Hypothesis. It is likely
that these elevated cortisol levels are also seen in people with MS.
The possible link between EMG in the jaw muscles and rises in saliva
cortisol levels during yawning were investigated in a randomized
controlled trial of 60 volunteers aged 18-69 years who were exposed
to conditions that were designed to elicit the yawning response.
Saliva samples were collected at the start and after yawning, or at the
end of the presentation of yawning-provoking stimuli, in the absence
of a yawn, and EMG data was additionally collected during rest and
yawning phases. Hospital Anxiety and Depression Scale, Yawning
Susceptibility Scale, General Health Questionnaire, demographic,
and health details were collected and the following exclusion criteria
were adopted: chronic fatigue, diabetes, fibromyalgia, heart
condition, high blood pressure, hormone replacement therapy,
multiple sclerosis, and stroke. Significant differences were found
between the saliva cortisol samples for the yawners, t (23) = -4.263, p
= 0.000, as compared with the non-yawners between rest and poststimuli,
which was non-significant. There were also significant
differences between yawners and non-yawners for the EMG
potentials with the yawners having higher rest and post-yawning
potentials. Significant evidence was found to support the Thompson
Cortisol Hypothesis suggesting that rises in cortisol levels are
associated with the yawning response. Further research is underway
to explore the use of cortisol as a potential diagnostic tool as an assist
to the early diagnosis of symptoms related to neurological disorders.
Bournemouth University Research & Ethics approval granted:
JC28/1/13-KA6/9/13. Professional code of conduct, confidentiality,
and safety issues have been addressed and approved in the Ethics
submission. Trials identification number: ISRCTN61942768.
http://www.controlled-trials.com/isrctn/
Abstract: This paper presents the result of an experimental
investigation regarding the use of Fe2O3 nanoparticles added to
kerosene as a working fluid, under magnetic field for Copper
Oscillating Heat pipe with inclination angle of 0°(horizontal), 15°,
30°,45°, 60°,75° and 90° (vertical). The following were examined;
measure the temperature distribution and heat transfer rate on
Oscillating Heat Pipe (OHP), with magnetic field under different
angles. Results showed that the addition of Fe2O3 nanoparticles under
magnetic field improved thermal performance of OHP especially in
75°.
Abstract: High moisture content in fruits generates post-harvest
problems such as mechanical, biochemical, microbial and physical
losses. Dehydration, which is based on the reduction of water activity
of the fruit, is a common option for overcoming such losses.
However, regular hot air drying could affect negatively the quality
properties of the fruit due to the long residence time at high
temperature. Power ultrasound (US) application during the
convective drying has been used as a novel method able to enhance
drying rate and, consequently, to decrease drying time. In the present
study, a new approach was tested to evaluate the effect of US on the
drying time, the final antioxidant activity (AA) and the total
polyphenol content (TPC) of banana slices (BS), mango slices (MS)
and guava slices (GS). There were also studied the drying kinetics
with nine different models from which water effective diffusivities
(Deff) (with or without shrinkage corrections) were calculated.
Compared with the corresponding control tests, US assisted drying
for fruit slices showed reductions in drying time between 16.23 and
30.19%, 11.34 and 32.73%, and 19.25 and 47.51% for the MS, BS
and GS respectively. Considering shrinkage effects, Deff calculated
values ranged from 1.67*10-10 to 3.18*10-10 m2/s, 3.96*10-10 and
5.57*10-10 m2/s and 4.61*10-10 to 8.16*10-10 m2/s for the BS, MS and
GS samples respectively. Reductions of TPC and AA (as DPPH)
were observed compared with the original content in fresh fruit data
in all kinds of drying assays.
Abstract: Cloud Computing refers to applications delivered as
services over the internet, and the datacenters that provide those
services with hardware and systems software. These were earlier
referred to as Software as a Service (SaaS). Scheduling is justified by
job components (called tasks), lack of information. In fact, in a large
fraction of jobs from machine learning, bio-computing, and image
processing domains, it is possible to estimate the maximum time
required for a task in the job. This study focuses on Trust based
scheduling to improve cloud security by modifying Heterogeneous
Earliest Finish Time (HEFT) algorithm. It also proposes TR-HEFT
(Trust Reputation HEFT) which is then compared to Dynamic Load
Scheduling.