Abstract: The objective of this work is to study the influence of the properties of the substrate on the retrofit (thin repair) of damaged concrete elements, with the SCC. Fluidity, principal characteristic of the SCC, would enable it to cover and adhere to the concrete to be repaired. Two aspects of repair are considered, the bond (Adhesion) and the tensile strength and the cracking. The investigation is experimental; It was conducted over test specimens made up of ordinary concrete prepared and hardened in advance (the material to be repaired) over which a self compacting concrete layer is cast. Three alternatives of SC concrete and one ordinary concrete (comparison) were tested. It appears that the self-compacting concrete constitutes a good material for repairing. It follows perfectly the surfaces- forms to be repaired and allows a perfect bond. Fracture tests made on specimens of self-compacting concrete show a brittle behaviour. However when a small percentage of fibres is added, the resistance to cracking is very much improve.
Abstract: Sedimentation in reservoirs and the corresponding
loss of storage capacity is one of the most serious problems in dam
engineering. Pressurized flushing, a way to remove sediments from the reservoir, is flushing under a pressurized flow condition and
nearly constant water level. Pressurized flushing has only local
effects around the outlet. Sediment in the vicinity of the outlet openings is scoured and a funnel shaped crater is created. In this study, the temporal development of flushing cone under various
hydraulic conditions was studied experimentally. Time variations of
parameters such as maximum length and width of flushing and also
depth of scouring cone was measured. Results indicated that an
increase in flow velocity (and consequently in Froude number)
established new hydraulically conditions for flushing mechanism and
so a sudden growth was observed in the amount of sediment released
and also scouring dimenssions. In addition, a set of nondimensional
relationships were identified for temporal variations of flushing scour
dimenssions, which can eventuallt be used to estimate the development of flushing cone.
Abstract: The study describes chitosan membrane platform
modified with nanostructure pattern which using nanotechnology to
fabricate. The cell-substrate interaction between neuro-2a neuroblasts
cell lines and chitosan membrane (flat, nanostructure and
nanostructure pattern types) was investigated. The adhered
morphology of neuro-2a cells depends on the topography of chitosan
surface. We have found that neuro-2a showed different morphogenesis
when cells adhered on flat and nanostructure chitosan membrane. The
cell projected area of neuro-2a on flat chitosan membrane is larger
than on nanostructure chitosan membrane. In addition, neuro-2a cells
preferred to adhere on flat chitosan surface region than on
nanostructure chitosan membrane to immobilize and differentiation.
The experiment suggests surface topography can be used as a critical
mechanism to isolate group of neuro-2a to a particular rectangle area
on chitosan membrane. Our finding will provide a platform to take
patch clamp to record electrophysiological behavior about neurons in
vitro in the future.
Abstract: Standard packaging and interconnection technologies
of power devices have difficulties meeting the increasing thermal
demands of new application fields of power electronics devices.
Main restrictions are the decreasing reliability of bond-wires and
solder layers with increasing junction temperature. In the last few
years intensive efforts have been invested in developing new
packaging and interconnection solutions which may open a path to
future application of power devices. In this paper, the main failure
mechanisms of power devices are described and principle of new
packaging and interconnection concepts and their power cycling
reliability are presented.
Abstract: Two freshwater fishes, Rasbora sumatrana
(Cyprinidae) and Poecilia reticulata (guppy) (Poeciliidae) were
exposed for a four-day period in the laboratory condition to a range
of copper (Cu) and cadmium (Cd) concentrations. Mortality was
assessed and median lethal concentrations (LC50) were calculated.
LC50 increased with decrease in mean exposure times for both metals.
For R. sumatrana, LC50s for 24, 48, 72 and 96 hours for Cu were
54.2, 30.3, 18.9 and 5.6 μg/L and for Cd 1440.2, 459.3, 392.3 and
101.6 μg/L respectively. For P. reticulata, LC50s for 24, 48, 72 and
96 hours for Cu were 348.9, 145.4, 61.3 and 37.9 μg/L and for Cd
8205.6, 2827.1, 405.8 and 168.1 μg/L, respectively. Results indicated
that the Cu was more toxic than Cd to both fishes (Cu>Cd) and R.
sumatrana was more sensitive than P. reticulata to the metals.
Abstract: ICA which is generally used for blind source separation
problem has been tested for feature extraction in Speech recognition
system to replace the phoneme based approach of MFCC. Applying
the Cepstral coefficients generated to ICA as preprocessing has
developed a new signal processing approach. This gives much better
results against MFCC and ICA separately, both for word and speaker
recognition. The mixing matrix A is different before and after MFCC
as expected. As Mel is a nonlinear scale. However, cepstrals
generated from Linear Predictive Coefficient being independent
prove to be the right candidate for ICA. Matlab is the tool used for
all comparisons. The database used is samples of ISOLET.
Abstract: De novo genome assembly is always fragmented. Assembly fragmentation is more serious using the popular next generation sequencing (NGS) data because NGS sequences are shorter than the traditional Sanger sequences. As the data throughput of NGS is high, the fragmentations in assemblies are usually not the result of missing data. On the contrary, the assembled sequences, called contigs, are often connected to more than one other contigs in a complicated manner, leading to the fragmentations. False connections in such complicated connections between contigs, named a contig graph, are inevitable because of repeats and sequencing/assembly errors. Simplifying a contig graph by removing false connections directly improves genome assembly. In this work, we have developed a tool, SIMGraph, to resolve ambiguous connections between contigs using NGS data. Applying SIMGraph to the assembly of a fungus and a fish genome, we resolved 27.6% and 60.3% ambiguous contig connections, respectively. These results can reduce the experimental efforts in resolving contig connections.
Abstract: Short circuit currents plays a vital role in influencing the design and operation of equipment and power system and could not be avoided despite careful planning and design, good maintenance and thorough operation of the system. This paper discusses the short circuit analysis conducted in KSO briefly comprising of its significances, methods and results. A result sample of the analysis based on a single transformer is detailed in this paper. Furthermore, the results of the analysis and its significances were also discussed and commented.
Abstract: Phase locked loops for data links operating at 10 Gb/s
or faster are low phase noise devices designed to operate with a low
jitter reference clock. Characterization of their jitter transfer function
is difficult because the intrinsic noise of the device is comparable to
the random noise level in the reference clock signal. A linear model
is proposed to account for the intrinsic noise of a PLL. The intrinsic
noise data of a PLL for 10 Gb/s links is presented. The jitter transfer
function of a PLL in a test chip for 12.8 Gb/s data links was
determined in experiments using the 400 MHz reference clock as the
source of simultaneous excitations over a wide range of frequency.
The result shows that the PLL jitter transfer function can be
approximated by a second order linear model.
Abstract: Geographic Information System (GIS) is a computerbased
tool used extensively to solve various engineering problems
related to spatial data. In spite of growing popularity of GIS, its
complete potential to construction industry has not been realized. In
this paper, the summary of up-to-date work on spatial applications of
GIS technologies in construction industry is presented. GIS
technologies have the potential to solve space related problems of
construction industry involving complex visualization, integration of
information, route planning, E-commerce, cost estimation, etc. GISbased
methodology to handle time and space issues of construction
projects scheduling is developed and discussed in this paper.
Abstract: Power-line networks are widely used today for broadband data transmission. However, due to multipaths within the broadband power line communication (BPLC) systems owing to stochastic changes in the network load impedances, branches, etc., network or channel capacity performances are affected. This paper attempts to investigate the performance of typical medium voltage channels that uses Orthogonal Frequency Division Multiplexing (OFDM) techniques with Quadrature Amplitude Modulation (QAM) sub carriers. It has been observed that when the load impedances are different from line characteristic impedance channel performance decreases. Also as the number of branches in the link between the transmitter and receiver increases a loss of 4dB/branch is found in the signal to noise ratio (SNR). The information presented in the paper could be useful for an appropriate design of the BPLC systems.
Abstract: This paper undertakes the problem of optimal
capacitor placement in a distribution system. The problem is how to
optimally determine the locations to install capacitors, the types and
sizes of capacitors to he installed and, during each load level,the
control settings of these capacitors in order that a desired objective
function is minimized while the load constraints,network constraints
and operational constraints (e.g. voltage profile) at different load
levels are satisfied. The problem is formulated as a combinatorial
optimization problem with a nondifferentiable objective function.
Four solution mythologies based on algorithms (GA),tabu search
(TS), and hybrid GA-SA algorithms are presented.The solution
methodologies are preceded by a sensitivity analysis to select the
candidate capacitor installation locations.
Abstract: This paper presents an idea to improve the efficiency
of security checks in airports through the active tracking and
monitoring of passengers and staff using OFDM modulation
technique and Finger print authentication. The details of the
passenger are multiplexed using OFDM .To authenticate the
passenger, the fingerprint along with important identification
information is collected. The details of the passenger can be
transmitted after necessary modulation, and received using various
transceivers placed within the premises of the airport, and checked at
the appropriate check points, thereby increasing the efficiency of
checking. OFDM has been employed for spectral efficiency.
Abstract: With the proliferation of mobile computing technology, mobile learning (m-learning) will play a vital role in the rapidly growing electronic learning market. However, the acceptance of m-learning by individuals is critical to the successful implementation of m-learning systems. Thus, there is a need to research the factors that affect users- intention to use m-learning. Based on an updated information system (IS) success model, data collected from 350 respondents in Taiwan were tested against the research model using the structural equation modeling approach. The data collected by questionnaire were analyzed to check the validity of constructs. Then hypotheses describing the relationships between the identified constructs and users- satisfaction were formulated and tested.
Abstract: In the planning point of view, it is essential to have
mode choice, due to the massive amount of incurred in transportation
systems. The intercity travellers in Libya have distinct features, as
against travellers from other countries, which includes cultural and
socioeconomic factors. Consequently, the goal of this study is to
recognize the behavior of intercity travel using disaggregate models,
for projecting the demand of nation-level intercity travel in Libya.
Multinomial Logit Model for all the intercity trips has been
formulated to examine the national-level intercity transportation in
Libya. The Multinomial logit model was calibrated using nationwide
revealed preferences (RP) and stated preferences (SP) survey. The
model was developed for deference purpose of intercity trips (work,
social and recreational). The variables of the model have been
predicted based on maximum likelihood method. The data needed for
model development were obtained from all major intercity corridors
in Libya. The final sample size consisted of 1300 interviews. About
two-thirds of these data were used for model calibration, and the
remaining parts were used for model validation. This study, which is
the first of its kind in Libya, investigates the intercity traveler’s
mode-choice behavior. The intercity travel mode-choice model was
successfully calibrated and validated. The outcomes indicate that, the
overall model is effective and yields higher precision of estimation.
The proposed model is beneficial, due to the fact that, it is receptive
to a lot of variables, and can be employed to determine the impact of
modifications in the numerous characteristics on the need for various
travel modes. Estimations of the model might also be of valuable to
planners, who can estimate possibilities for various modes and
determine the impact of unique policy modifications on the need for
intercity travel.
Abstract: This paper presents results obtained from the
numerical solution for the flow past an oscillating circular cylinder at
Reynolds number of 200. The frequency of oscillation was fixed to
the vortex shedding frequency from a fixed cylinder, f0, while the
amplitudes of oscillations were varied from to 1.1a, where a
represents the radius of the cylinder. The response of the flow
through the fluid forces acting on the surface of the cylinder are
investigated. The lock-on phenomenon is captured at low oscillation
amplitudes.
Abstract: One of the primary uses of higher order statistics in
signal processing has been for detecting and estimation of non-
Gaussian signals in Gaussian noise of unknown covariance. This is
motivated by the ability of higher order statistics to suppress additive
Gaussian noise. In this paper, several methods to test for non-
Gaussianity of a given process are presented. These methods include
histogram plot, kurtosis test, and hypothesis testing using cumulants
and bispectrum of the available sequence. The hypothesis testing is
performed by constructing a statistic to test whether the bispectrum
of the given signal is non-zero. A zero bispectrum is not a proof of
Gaussianity. Hence, other tests such as the kurtosis test should be
employed. Examples are given to demonstrate the performance of the
presented methods.
Abstract: An innovative approach utilizing highly alkaline oil
shale waste ash and carbon dioxide gas (CO2), associated with power
production, as a resource for production of precipitated calcium
carbonate (PCC) is introduced in this paper. The specifics and
feasibility of the integrated ash valorization and CO2 sequestration
process by indirect aqueous carbonation of lime-consisting ash were
elaborated and the main parameters established. Detailed description
of the formed precipitates was included. Complimentary carbonation
experiments with commercial CaO fine powder were conducted for
comparative characterization of the final products obtained on the
basis of two different raw materials. Finally, the expected CO2
uptake was evaluated.
Abstract: The objective of positioning the fixture elements in
the fixture is to make the workpiece stiff, so that geometric errors in
the manufacturing process can be reduced. Most of the work for
optimal fixture layout used the minimization of the sum of the nodal
deflection normal to the surface as objective function. All deflections
in other direction have been neglected. We propose a new method for
fixture layout optimization in this paper, which uses the element
strain energy. The deformations in all the directions have been
considered in this way. The objective function in this method is to
minimize the sum of square of element strain energy. Strain energy
and stiffness are inversely proportional to each other. The
optimization problem is solved by the sequential quadratic
programming method. Three different kinds of case studies are
presented, and results are compared with the method using nodal
deflections as objective function to verify the propose method.
Abstract: A wide spectrum of systems require reliable
personal recognition schemes to either confirm or determine the
identity of an individual person. This paper considers multimodal
biometric system and their applicability to access control,
authentication and security applications. Strategies for feature
extraction and sensor fusion are considered and contrasted. Issues
related to performance assessment, deployment and standardization
are discussed. Finally future directions of biometric systems
development are discussed.