Abstract: Continuous-time delta-sigma analog digital converter (ADC) for radio frequency identification (RFID) complementary metal oxide semiconductor (CMOS) biosensor has been reported. This delta-sigma ADC is suitable for digital conversion of biosensor signal because of small process variation, and variable input range. As the input range of continuous-time switched current delta-sigma ADC (Dynamic range : 50 dB) can be limited by using current reference, amplification of biosensor signal is unnecessary. The input range is switched to wide input range mode or narrow input range mode by command of current reference. When the narrow input range mode, the input range becomes ± 0.8 V. The measured power consumption is 5 mW and chip area is 0.31 mm^2 using 1.2 um standard CMOS process. Additionally, automatic input range detecting system is proposed because of RFID biosensor applications.
Abstract: As the world move to the accomplishment of Performance Based Engineering philosophies in seismic design of Civil Engineering structures, new seismic design provisions require Structural Engineers to perform both static and dynamic analysis for the design of structures. While Linear Equivalent Static Analysis is performed for regular buildings up to 90m height in zone I and II, Dynamic Analysis should be performed for regular and irregular buildings in zone IV and V. Dynamic Analysis can take the form of a dynamic Time History Analysis or a linear Response Spectrum Analysis. In present study, Multi-storey irregular buildings with 20 stories have been modeled using software packages ETABS and SAP 2000 v.15 for seismic zone V in India. This paper also deals with the effect of the variation of the building height on the structural response of the shear wall building. Dynamic responses of building under actual earthquakes, EL-CENTRO 1949 and CHI-CHI Taiwan 1999 have been investigated. This paper highlights the accuracy and exactness of Time History analysis in comparison with the most commonly adopted Response Spectrum Analysis and Equivalent Static Analysis.
Abstract: Mung bean starches were subjected to heat-moisture treatment (HMT) by different moisture contents (15%, 20%, 25%, 30% and 35%) at 120Ôäâ for 12h. The impact on the yields of resistant starch (RS), microstructure, physicochemical and functional properties was investigated. Compared to native starch, the RS content of heat-moisture treated starches increased significantly. The RS level of HMT-20 was the highest of all the starches. Birefringence was displayed clear at the center of native starch. For HMT starches, pronounced birefringence was exhibited on the periphery of starch granules; however, birefringence disappeared at the centre of some starch granules. The shape of HMT starches hadn-t been changed and the integrity of starch granules was preserved for all the conditions. Concavity could be observed on HMT starches under scanning electronic microscopy. After HMT, apparent amylose contents were increased and starch macromolecule was degraded in comparison with those of native starch. There was a reduction in swelling power on HMT starches, but the solubility of HMT starches was higher than that of native starch. Both of native and HMT starches showed A-type X-ray diffraction pattern. Furthermore, there is a higher intensity at the peak of 15.0 and 22.9 Å than those of native starch.
Abstract: An application framework provides a reusable design
and implementation for a family of software systems. If the
framework contains defects, the defects will be passed on to the
applications developed from the framework. Framework defects are
hard to discover at the time the framework is instantiated. Therefore,
it is important to remove all defects before instantiating the
framework. In this paper, two measures for the adequacy of an
object-oriented system-based testing technique are introduced. The
measures assess the usefulness and uniqueness of the testing
technique. The two measures are applied to experimentally compare
the adequacy of two testing techniques introduced to test objectoriented
frameworks at the system level. The two considered testing
techniques are the New Framework Test Approach and Testing
Frameworks Through Hooks (TFTH). The techniques are also
compared analytically in terms of their coverage power of objectoriented
aspects. The comparison study results show that the TFTH
technique is better than the New Framework Test Approach in terms
of usefulness degree, uniqueness degree, and coverage power.
Abstract: Natural disasters, including earthquake, kill many people around the world every year. Society rescue actions, which start after the earthquake and are called LAST in abbreviation, include locating, access, stabilization and transportation. In the present article, we have studied the process of local accessibility to the injured and transporting them to health care centers. With regard the heavy traffic load due to earthquake, the destruction of connecting roads and bridges and the heavy debris in alleys and street, which put the lives of the injured and the people buried under the debris in danger, accelerating the rescue actions and facilitating the accessibilities are of great importance, obviously. Tehran, the capital of Iran, is among the crowded cities in the world and is the center of extensive economic, political, cultural and social activities. Tehran has a population of about 9.5 millions and because of the immigration of people from the surrounding cities. Furthermore, considering the fact that Tehran is located on two important and large faults, a 6 Richter magnitude earthquake in this city could lead to the greatest catastrophe during the entire human history. The present study is a kind of review and a major part of the required information for it, has been obtained from libraries all of the rescue vehicles around the world, including rescue helicopters, ambulances, fire fighting vehicles and rescue boats, and their applied technology, and also the robots specifically designed for the rescue system and the advantages and disadvantages of them, have been investigated. The studies show that there is a significant relationship between the rescue team-s arrival time at the incident zone and the number of saved people; so that, if the duration of burial under debris 30 minutes, the probability of survival is %99.3, after a day is %81, after 2days is %19 and after 5days is %7.4. The exiting transport systems all have some defects. If these defects are removed, more people could be saved each hour and the preparedness against natural disasters is increased. In this study, transport system has been designed for the rescue team and the injured; which could carry the rescue team to the incident zone and the injured to the health care centers. In addition, this system is able to fly in the air and move on the earth as well; so that the destruction of roads and the heavy traffic load could not prevent the rescue team from arriving early at the incident zone. The system also has the equipment required firebird for debris removing, optimum transport of the injured and first aid.
Abstract: E-travel is travel agency-s companies employing internet and website as e-commerce context. This study presents numerous initial key factors of electronic travel model based on small travel agencies perspectives. Browsing previous studies related to website travel activities are conducted. Five small travel agencies in Indonesia has been deeply interviewed in case studies. The finding of this research is identifying numerous characteristics and dimension factors and travel website operations including ownermanager roles, business experiences, characteristically business, and technological aspects. This study is the preliminary research related to travel website adoption in Indonesia. The further study would be conducted in questionnaires of the quantitative research in Indonesia contexts as a developing country.
Abstract: None of the processing models in the software
development has explained the software systems performance
evaluation and modeling; likewise, there exist uncertainty in the
information systems because of the natural essence of requirements,
and this may cause other challenges in the processing of software
development. By definition an extended version of UML (Fuzzy-
UML), the functional requirements of the software defined
uncertainly would be supported. In this study, the behavioral
description of uncertain information systems by the aid of fuzzy-state
diagram is crucial; moreover, the introduction of behavioral diagrams
role in F-UML is investigated in software performance modeling
process. To get the aim, a fuzzy sub-profile is used.
Abstract: Levan, an exopolysaccharide, was produced by
Microbacterium laevaniformans and its yield was characterized as a
function of concentrations of date syrup, sucrose and the fermentation
time. The optimum condition for levan production from sucrose was
at concentration of 20% sucrose for 48 h and for date syrup was 25%
for 48 h. The results show that an increase in fermentation time
caused a decrease in the levan production at all concentrations of date
syrup tested. Under these conditions after 48 h in sucrose medium,
levan production reached 48.9 g/L and for date syrup reached 10.48
g/L . The effect of pH on the yield of the purified levan was examined
and the optimum pH for levan production was determined to be 6.0.
Levan was composed mainly of fructose residues when analyzed by
TLC and FT-IR spectroscopy. Date syrup is a cheap substrate widely
available in Iran and has potential for levan production. The thermal
stability of levan was assessed by Thermo Gravimetric Analysis
(TGA) that revealed the onset of decomposition near to 49°C for the
levan produced from sucrose and 51°C for the levan from date syrup.
DSC results showed a single Tg at 98°C for levan produced from
sucrose and 206 °C for levan from date syrup.
Abstract: In this paper, a new time-delay estimation
technique based on the cross IB-energy operator [5] is
introduced. This quadratic energy detector measures how
much a signal is present in another one. The location of the
peak of the energy operator, corresponding to the maximum of
interaction between the two signals, is the estimate of the
delay. The method is a fully data-driven approach. The
discrete version of the continuous-time form of the cross IBenergy
operator, for its implementation, is presented. The
effectiveness of the proposed method is demonstrated on real
underwater acoustic signals arriving from targets and the
results compared to the cross-correlation method.
Abstract: This paper presents the results of the experimental
tests of the cooling performance of a 12,000-Btu/h modified air
conditioner (referred to as M-AC) that use the ground as a heat sink
of a condenser. In the tests, cooling capacity of M-AC with an
optimal length of a condensing coil as well as life expectancy of
copper coil buried underground were investigated. The lengths of
copper coil fabricated and used as condenser coil of M-AC were set
at 67, 50, 40 and 30 m whereas that of a 12,000-Btu/h conventional
split-type air conditioner (referred to as C-AC) was about 22 m. The
results showed that the ground can absorb heat rejected from a
condenser of M-AC. The coefficient of performance (COP) of C-AC
was about 2.5 whereas those of M-AC were found to be higher. It
was found that the values of COP of M-AC with condensing coils of
67, 50 and 40 m long were about 6.9, 5.5 and 3.3, respectively, while
that of 30-m-long one was found to be about 2.1. The electrical
consumptions of M-AC were found lower than that of C-AC in the
range of 11.5 – 15.5%. Additionally, life expectancy of underground
condensing coil of M-AC was found to be over 7 years.
Abstract: Human identification at a distance has recently gained
growing interest from computer vision researchers. Gait recognition
aims essentially to address this problem by identifying people based
on the way they walk [1]. Gait recognition has 3 steps. The first step
is preprocessing, the second step is feature extraction and the third
one is classification. This paper focuses on the classification step that
is essential to increase the CCR (Correct Classification Rate).
Multilayer Perceptron (MLP) is used in this work. Neural Networks
imitate the human brain to perform intelligent tasks [3].They can
represent complicated relationships between input and output and
acquire knowledge about these relationships directly from the data
[2]. In this paper we apply MLP NN for 11 views in our database and
compare the CCR values for these views. Experiments are performed
with the NLPR databases, and the effectiveness of the proposed
method for gait recognition is demonstrated.
Abstract: The technology usages of high speed Internet leads to
establish and start new era of online education. With the
advancement of the information technology and communication
systems new opportunities have been created. This leads universities
to have various online education channels to meet the demand of
different learners- needs. One of these channels is M-learning, which
can be used to improve the online education environment. With using
such mobile technology in learning both students and instructors can
easily access educational courses anytime from anywhere. The paper
first presents literature about mobile learning and to what extent this
approach can be utilized to enhance the overall learning system. It
provides a comparison between mobile learning and traditional elearning
showing the wide array of benefits of the new generation of
technology. The possible challenges and potential advantages of Mlearning
in the online education system are also discussed.
Abstract: Trust management and Reputation models are
becoming integral part of Internet based applications such as CSCW,
E-commerce and Grid Computing. Also the trust dimension is a
significant social structure and key to social relations within a
collaborative community. Collaborative Decision Making (CDM) is
a difficult task in the context of distributed environment (information
across different geographical locations) and multidisciplinary
decisions are involved such as Virtual Organization (VO). To aid
team decision making in VO, Decision Support System and social
network analysis approaches are integrated. In such situations social
learning helps an organization in terms of relationship, team
formation, partner selection etc. In this paper we focus on trust
learning. Trust learning is an important activity in terms of
information exchange, negotiation, collaboration and trust
assessment for cooperation among virtual team members. In this
paper we have proposed a reinforcement learning which enhances the
trust decision making capability of interacting agents during
collaboration in problem solving activity. Trust computational model
with learning that we present is adapted for best alternate selection of
new project in the organization. We verify our model in a multi-agent
simulation where the agents in the community learn to identify
trustworthy members, inconsistent behavior and conflicting behavior
of agents.
Abstract: We have previously introduced an ultrasonic imaging
approach that combines harmonic-sensitive pulse sequences with a
post-beamforming quadratic kernel derived from a second-order
Volterra filter (SOVF). This approach is designed to produce images
with high sensitivity to nonlinear oscillations from microbubble
ultrasound contrast agents (UCA) while maintaining high levels of
noise rejection. In this paper, a two-step algorithm for computing the
coefficients of the quadratic kernel leading to reduction of tissue
component introduced by motion, maximizing the noise rejection and
increases the specificity while optimizing the sensitivity to the UCA
is presented. In the first step, quadratic kernels from individual
singular modes of the PI data matrix are compared in terms of their
ability of maximize the contrast to tissue ratio (CTR). In the second
step, quadratic kernels resulting in the highest CTR values are
convolved. The imaging results indicate that a signal processing
approach to this clinical challenge is feasible.
Abstract: In this paper, the modified optimal sliding mode control with a proposed method to design a sliding surface is presented. Because of the inability of the previous approach of the sliding mode method to design a bounded and suitable input, the new variation is proposed in the sliding manifold to obviate problems in a structural system. Although the sliding mode control is a powerful method to reject disturbances and noises, the chattering problem is not good for actuators. To decrease the chattering phenomena, the optimal control is added to the sliding mode control. Not only the proposed method can decline the intense variations in the inputs of the system but also it can produce the efficient responses respect to the sliding mode control and optimal control that are shown by performing some numerical simulations.
Abstract: The effect of wheat flour extraction rates on flour
composition, farinographic characteristics and the quality of
sourdough naans was investigated. The results indicated that by
increasing the extraction rate, the amount of protein, fiber, fat and
ash increased, whereas moisture content decreased. Farinographic
characteristic like water absorption and dough development time
increased with an increase in flour extraction rate but the dough
stabilities and tolerance indices were reduced with an increase in
flour extraction rates. Titratable acidity for both sourdough and
sourdough naans also increased along with flour extraction rate. The
study showed that overall quality of sourdough naans were affected
by both flour extraction rate and starter culture used. Sensory
analysis of sourdough naans revealed that desirable extraction rate
for sourdough naan was 76%.
Abstract: In this paper, a delayed physiological control system is investigated. The sufficient conditions for stability of positive equilibrium and existence of local Hopf bifurcation are derived. Furthermore, global existence of periodic solutions is established by using the global Hopf bifurcation theory. Finally, numerical examples are given to support the theoretical analysis.
Abstract: In this paper, a new formulation for acoustics coupled with linear elasticity is presented. The primary objective of the work is to develop a three dimensional hp adaptive finite element method code destinated for modeling of acoustics of human head. The code will have numerous applications e.g. in designing hearing protection devices for individuals working in high noise environments. The presented work is in the preliminary stage. The variational formulation has been implemented and tested on a sequence of meshes with concentric multi-layer spheres, with material data representing the tissue (the brain), skull and the air. Thus, an efficient solver for coupled elasticity/acoustics problems has been developed, and tested on high contrast material data representing the human head.
Abstract: In this paper the behavior of fixed series compensated
extra high voltage transmission lines during faults is simulated. Many
over-voltage protection schemes for series capacitors are limited in
terms of size and performance, and are easily affected by
environmental conditions. While the need for more compact and
environmentally robust equipment is required. use of series
capacitors for compensating part of the inductive reactance of long
transmission lines increases the power transmission capacity.
Emphasis is given on the impact of modern capacitor protection
techniques (MOV protection). The simulation study is performed
using MATLAB/SIMULINK®and results are given for a three phase
and a single phase to ground fault.
Abstract: This work is an attempt to use the standard Smoothed
Particle Hydrodynamics methodology for the simulation of the
complex unsteady, free-surface flow in a rotating Turgo impulse
water turbine. A comparison of two different geometries was
conducted. The SPH method due to its mesh-less nature is capable of
capturing the flow features appearing in the turbine, without
diffusion at the water/air interface. Furthermore results are compared
with a commercial CFD package (Fluent®) and the SPH algorithm
proves to be capable of providing similar results, in much less time
than the mesh based CFD program. A parametric study was also
performed regarding the turbine inlet angle.