Abstract: Sewer deposits have been identified as a major cause
of dysfunctions in combined sewer systems regarding sewer
management, which induces different negative consequents resulting
in poor hydraulic conveyance, environmental damages as well as
worker’s health. In order to overcome the problematics of
sedimentation, flushing has been considered as the most operative
and cost-effective way to minimize the sediments impacts and
prevent such challenges. Flushing, by prompting turbulent wave
effects, can modify the bed form depending on the hydraulic
properties and geometrical characteristics of the conduit. So far, the
dynamics of the bed-load during high-flow events in combined sewer
systems as a complex environment is not well understood, mostly due
to lack of measuring devices capable to work in the “hostile” in
combined sewer system correctly. In this regards, a one-episode
flushing issue from an opening gate valve with weir function was
carried out in a trunk sewer in Paris to understand its cleansing
efficiency on the sediments (thickness: 0-30 cm). During more than
1h of flushing within 5 m distance in downstream of this flushing
device, a maximum flowrate and a maximum level of water have
been recorded at 5 m in downstream of the gate as 4.1 m3/s and 2.1
m respectively. This paper is aimed to evaluate the efficiency of this
type of gate for around 1.1 km (from the point -50 m to +1050 m in
downstream from the gate) by (i) determining bed grain-size
distribution and sediments evolution through the sewer channel, as
well as their organic matter content, and (ii) identifying sections that
exhibit more changes in their texture after the flush. For the first one,
two series of sampling were taken from the sewer length and then
analyzed in laboratory, one before flushing and second after, at same
points among the sewer channel. Hence, a non-intrusive sampling
instrument has undertaken to extract the sediments smaller than the
fine gravels. The comparison between sediments texture after the
flush operation and the initial state, revealed the most modified zones
by the flush effect, regarding the sewer invert slope and hydraulic
parameters in the zone up to 400 m from the gate. At this distance,
despite the increase of sediment grain-size rages, D50 (median grainsize)
varies between 0.6 mm and 1.1 mm compared to 0.8 mm and 10
mm before and after flushing, respectively. Overall, regarding the
sewer channel invert slope, results indicate that grains smaller than
sands (< 2 mm) are more transported to downstream along about 400
m from the gate: in average 69% before against 38% after the flush
with more dispersion of grain-sizes distributions. Furthermore, high
effect of the channel bed irregularities on the bed material evolution
has been observed after the flush.
Abstract: The objective of this paper is to evaluate the effects of
soil-structure interaction (SSI) on the modal characteristics and on
the dynamic response of current structures. The objective is on the
overall behaviour of a real structure of five storeys reinforced
concrete (R/C) building typically encountered in Algeria. Sensitivity
studies are undertaken in order to study the effects of frequency
content of the input motion, frequency of the soil-structure system,
rigidity and depth of the soil layer on the dynamic response of such
structures. This investigation indicated that the rigidity of the soil
layer is the predominant factor in soil-structure interaction and its
increases would definitely reduce the deformation in the R/C
structure. On the other hand, increasing the period of the underlying
soil will cause an increase in the lateral displacements at story levels
and create irregularity in the distribution of story shears. Possible
resonance between the frequency content of the input motion and soil
could also play an important role in increasing the structural
response.
Abstract: Commercial banks in Nigeria adopted many strategies
to attract fresh deposits including the use of high deposit rate.
However, pricing of banking services moved in favor of the banks at
the expense of customers, resulting in their seeking other investment
alternatives rather than saving their money in the bank. Both deposit
and lending rates were greatly influenced by the Central Bank of
Nigeria (CBN) decision on interest rate. Therefore, commercial bank
effort to attract deposits via manipulation of her rates was greatly
limited, otherwise the banks will be giving out more than it earned.
The study aimed at examining the relationship between interest rate
and fixed fund deposit of commercial banks, how policy-controlled
interest rate affected commercial bank’s fixed fund deposit The
researcher employed ordinary least square technique, using, multiple
linear regression, unrestricted vector auto-regression, correlation
matrix test, granger causality and impulse response graph in the
analysis. Commercial bank’s interest rates affected commercial
bank’s fixed fund deposit significantly while policy-controlled
interest rate did not significantly transmit through the commercial
bank’s interest rates to affect fixed fund deposit. While commercial
banks seek creative ways to expand their fixed fund deposit, policy
authorities in Nigeria should better coordinate interest rate fluctuation
and induce competition in the entire financial sector.
Abstract: One of the most critical decision points in the design of a
face recognition system is the choice of an appropriate face representation.
Effective feature descriptors are expected to convey sufficient, invariant
and non-redundant facial information. In this work we propose a set of
Hahn moments as a new approach for feature description. Hahn moments
have been widely used in image analysis due to their invariance, nonredundancy
and the ability to extract features either globally and locally.
To assess the applicability of Hahn moments to Face Recognition we
conduct two experiments on the Olivetti Research Laboratory (ORL)
database and University of Notre-Dame (UND) X1 biometric collection.
Fusion of the global features along with the features from local facial
regions are used as an input for the conventional k-NN classifier. The
method reaches an accuracy of 93% of correctly recognized subjects for
the ORL database and 94% for the UND database.
Abstract: This study integrates a larger research empirical
project that examines second language (SL) learners’ profiles and
valid procedures to perform complete and diagnostic assessment in
schools. 102 learners of Portuguese as a SL aged 7 and 17 years
speakers of distinct home languages were assessed in several
linguistic tasks. In this article, we focused on writing performance in
the specific task of narrative essay composition. The written outputs
were measured using the score in six components adapted from an
English SL assessment context (Alberta Education): linguistic
vocabulary, grammar, syntax, strategy, socio-linguistic, and
discourse. The writing processes and strategies in Portuguese
language used by different immigrant students were analysed to
determine features and diversity of deficits on authentic texts
performed by SL writers. Differentiated performance was based on
the diversity of the following variables: grades, previous schooling,
home language, instruction in first language, and exposure to
Portuguese as Second Language. Indo-Aryan languages speakers
showed low writing scores compared to their peers and the type of
language and respective cognitive mapping (such as Mandarin and
Arabic) was the predictor, not linguistic distance. Home language
instruction should also be prominently considered in further research
to understand specificities of cognitive academic profile in a
Romance languages learning context. Additionally, this study also
examined the teachers’ representations that will be here addressed to
understand educational implications of second language teaching in
psychological distress of different minorities in schools of specific
host countries.
Abstract: Work presented is interested in the characterization of
the quasistatic mechanical properties and in fatigue of a composite
laminated in jute/epoxy. The natural fibers offer promising prospects
thanks to their interesting specific properties, because of their low
density, but also with their bio-deterioration. Several scientific
studies highlighted the good mechanical resistance of the vegetable
fiber composites reinforced, even after several recycling. Because of
the environmental standards that become increasingly severe, one
attends the emergence of eco-materials at the base of natural fibers
such as flax, bamboo, hemp, sisal, jute. The fatigue tests on
elementary vegetable fibers show an increase of about 60% of the
rigidity of elementary fibers of hemp subjected to cyclic loadings. In
this study, the test-tubes manufactured by the method infusion have
sequences of stacking of 0/90° and ± 45° for the shearing and tensile
tests. The quasistatic tests reveal a variability of the mechanical
properties of about 8%. The tensile fatigue tests were carried out for
levels of constraints equivalent to half of the ultimate values of the
composite. Once the fatigue tests carried out for well-defined values
of cycles, a series of static tests of traction type highlights the
influence of the number of cycles on the quasi-static mechanical
behavior of the laminate jute/epoxy.
Abstract: A solar dish collector has been designed, fabricated
and tested for its performance on 10-03-2015 in Salem, Tamilnadu,
India. The experiments on cooking vessels of coated and un-coated
with 5 Liters capacity have been used for cooking Rice. The results
are shown in graphs. The solar cooker is always capable of cooking
food within the expected length of time and based on the solar
radiation levels. With minimum cooking power, the coated pressure
cooker of 5 Liters capacity cooks the food at faster manner. This is
due to the conductivity of the coating material provided in the cooker.
Abstract: Over the past few years, a lot of research has been
conducted to bring Automatic Speech Recognition (ASR) into various
areas of Air Traffic Control (ATC), such as air traffic control
simulation and training, monitoring live operators for with the aim
of safety improvements, air traffic controller workload measurement
and conducting analysis on large quantities controller-pilot speech.
Due to the high accuracy requirements of the ATC context and its
unique challenges, automatic speech recognition has not been widely
adopted in this field. With the aim of providing a good starting
point for researchers who are interested bringing automatic speech
recognition into ATC, this paper gives an overview of possibilities
and challenges of applying automatic speech recognition in air traffic
control. To provide this overview, we present an updated literature
review of speech recognition technologies in general, as well as
specific approaches relevant to the ATC context. Based on this
literature review, criteria for selecting speech recognition approaches
for the ATC domain are presented, and remaining challenges and
possible solutions are discussed.
Abstract: High frequency automotive interior noise above 500
Hz considerably affects automotive passenger comfort. To reduce this
noise, sound insulation material is often laminated on body panels or
interior trim panels. For a more effective noise reduction, the sound
reduction properties of this laminated structure need to be estimated.
We have developed a new calculate tool that can roughly calculate the
sound absorption and insulation properties of laminate structure and
handy for designers. In this report, the outline of this tool and an
analysis example applied to floor mat are introduced.
Abstract: This research paper presents guiding on how to design
social media into higher education courses. The research
methodology used a survey approach. The research instrument was a
questionnaire about guiding on how to design social media into
higher education courses. Thirty-one lecturers completed the
questionnaire. The data were scored by frequency and percentage.
The research results were the lecturers’ opinions concerning the
designing social media into higher education courses as follows: 1)
Lecturers deem that the most suitable learning theory is Collaborative
Learning. 2) Lecturers consider that the most important learning and
innovation Skill in the 21st century is communication and
collaboration skills. 3) Lecturers think that the most suitable
evaluation technique is authentic assessment. 4) Lecturers consider
that the most appropriate portion used as blended learning should be
70% in the classroom setting and 30% online.
Abstract: This paper discusses the propagation of sound waves in
air, specifically in narrow rectangular pathways of an occluded-ear
simulator for acoustic measurements. In narrow pathways, both the
speed of sound and the phase of the sound waves are affected by the
damping of the air viscosity. Herein, we propose a new finite-element
method (FEM) that considers the effects of the air viscosity. The
method was developed as an extension of existing FEMs for porous,
sound-absorbing materials. The results of a numerical calculation for a
three-dimensional ear-simulator model using the proposed FEM were
validated by comparing with theoretical lumped-parameter modeling
analysis and standard values.
Abstract: In order to obtain efficient pollutants removal in
small-scale wastewater treatment plants, uniform water flow has to be
achieved. The experimental setup, designed for treating high-load
wastewater (leachate), consists of two aerobic biological reactors and
a lamellar settler. Both biological tanks were aerated by using three
different types of aeration systems - perforated pipes, membrane air
diffusers and tube ceramic diffusers. The possibility of homogenizing
the water mass with each of the air diffusion systems was evaluated
comparatively. The oxygen concentration was determined by optical
sensors with data logging. The experimental data was analyzed
comparatively for all three different air dispersion systems aiming to
identify the oxygen concentration variation during different
operational conditions. The Oxygenation Capacity was calculated for
each of the three systems and used as performance and selection
parameter. The global mass transfer coefficients were also evaluated
as important tools in designing the aeration system. Even though
using the tubular porous diffusers leads to higher oxygen
concentration compared to the perforated pipe system (which
provides medium-sized bubbles in the aqueous solution), it doesn’t
achieve the threshold limit of 80% oxygen saturation in less than 30
minutes. The study has shown that the optimal solution for the
studied configuration was the radial air diffusers which ensure an
oxygen saturation of 80% in 20 minutes. An increment of the values
was identified when the air flow was increased.
Abstract: Standard Gibbs energy of formation ΔGfor(298.15) of
lanthanide-iron double oxides of garnet-type crystal structure
R3Fe5O12 - RIG (R – are rare earth ions) from initial oxides are
evaluated. The calculation is based on the data of standard entropies
S298.15 and standard enthalpies ΔH298.15 of formation of compounds
which are involved in the process of garnets synthesis. Gibbs energy
of formation is presented as temperature function ΔGfor(T) for the
range 300-1600K. The necessary starting thermodynamic data were
obtained from calorimetric study of heat capacity – temperature
functions and by using the semi-empirical method for calculation of
ΔH298.15 of formation. Thermodynamic functions for standard
temperature – enthalpy, entropy and Gibbs energy - are
recommended as reference data for technological evaluations.
Through the structural series of rare earth-iron garnets the correlation
between thermodynamic properties and characteristics of lanthanide
ions are elucidated.
Abstract: There is currently a gap in the technology covering the
rapid establishment of control after a reconfiguration in a
Reconfigurable Manufacturing System. This gap involves the
detection of the factory floor state and the communication link
between the factory floor and the high-level software. In this paper, a
thin, hardware-supported Middleware Management System (MMS) is
proposed and its design and implementation are discussed. The
research found that a cost-effective localization technique can be
combined with intelligent software to speed up the ramp-up of a
reconfigured system. The MMS makes the process more intelligent,
more efficient and less time-consuming, thus supporting the
industrial implementation of the RMS paradigm.
Abstract: In this article, we deal with a variant of the classical
course timetabling problem that has a practical application in many
areas of education. In particular, in this paper we are interested in
high schools remedial courses. The purpose of such courses is to
provide under-prepared students with the skills necessary to succeed
in their studies. In particular, a student might be under prepared in
an entire course, or only in a part of it. The limited availability
of funds, as well as the limited amount of time and teachers at
disposal, often requires schools to choose which courses and/or which
teaching units to activate. Thus, schools need to model the training
offer and the related timetabling, with the goal of ensuring the
highest possible teaching quality, by meeting the above-mentioned
financial, time and resources constraints. Moreover, there are some
prerequisites between the teaching units that must be satisfied. We
first present a Mixed-Integer Programming (MIP) model to solve
this problem to optimality. However, the presence of many peculiar
constraints contributes inevitably in increasing the complexity of
the mathematical model. Thus, solving it through a general-purpose
solver may be performed for small instances only, while solving
real-life-sized instances of such model requires specific techniques
or heuristic approaches. For this purpose, we also propose a heuristic
approach, in which we make use of a fast constructive procedure
to obtain a feasible solution. To assess our exact and heuristic
approaches we perform extensive computational results on both
real-life instances (obtained from a high school in Lecce, Italy) and
randomly generated instances. Our tests show that the MIP model is
never solved to optimality, with an average optimality gap of 57%.
On the other hand, the heuristic algorithm is much faster (in about the
50% of the considered instances it converges in approximately half of
the time limit) and in many cases allows achieving an improvement
on the objective function value obtained by the MIP model. Such an
improvement ranges between 18% and 66%.
Abstract: Determination of genetic variation is useful for plant
breeding and hence production of more efficient plant species under
different conditions, like drought stress. In this study a sample of 28
recombinant inbred lines (RILs) of wheat developed from the cross of
Norstar and Zagross varieties, together with their parents, were
evaluated for two years (2010-2012) under normal and water stress
conditions using split plot design with three replications. Main plots
included two irrigation treatments of 70 and 140 mm evaporation
from Class A pan and sub-plots consisted of 30 genotypes. The effect
of genotypes and interaction of genotypes with years and water
regimes were significant for all characters. Significant genotypic
effect implies the existence of genetic variation among the lines
under study. Heritability estimates were high for 1000 grain weight
(0.87). Biomass and grain yield showed the lowest heritability values
(0.42 and 0.50, respectively). Highest genotypic and phenotypic
coefficients of variation (GCV and PCV) belonged to harvest index.
Moderate genetic advance for most of the traits suggested the
feasibility of selection among the RILs under investigation. Some
RILs were higher yielding than either parent at both environments.
Abstract: This paper presents a methodology for probabilistic
assessment of bearing capacity and prediction of failure mechanism
of masonry vaults at the ultimate state with consideration of the
natural variability of Young’s modulus of stones. First, the
computation model is explained. The failure mode corresponds to the
four-hinge mechanism. Based on this consideration, the study of a
vault composed of 16 segments is presented. The Young’s modulus of
the segments is considered as random variable defined by a mean
value and a coefficient of variation. A relationship linking the vault
bearing capacity to the voussoirs modulus variation is proposed. The
most probable failure mechanisms, in addition to that observed in the
deterministic case, are identified for each variability level as well as
their probability of occurrence. The results show that the mechanism
observed in the deterministic case has decreasing probability of
occurrence in terms of variability, while the number of other
mechanisms and their probability of occurrence increases with the
coefficient of variation of Young’s modulus. This means that if a
significant change in the Young’s modulus of the segments is proven,
taking it into account in computations becomes mandatory, both for
determining the vault bearing capacity and for predicting its failure
mechanism.
Abstract: New environmental regulations and the increasing
market preference for companies that respect the ecosystem had
encouraged the industry to look after new treatments for its effluents.
The sugar industry, one of the largest emitter of environmental
pollutants, follows this tendency. Membrane technology is
convenient for separation of suspended solids, colloids and high
molecular weight materials that are present in a wastewater from
sugar industry. The idea is to microfilter the wastewater, where the
permeate passes through the membrane and becomes available for
recycle and re-use in the sugar manufacturing process. For
microfiltration of this effluent a tubular ceramic membrane was used
with a pore size of 200 nm at transmembrane pressure in range of 1–3
bars and in range of flow rate of 50–150 l/h. Kenics static mixer was
used for permeate flux enhancement. Turbidity and suspended solids
were removed and the permeate flux was continuously monitored
during the microfiltration process. The flux achieved after 90 minutes
of microfiltration was in a range of 50–70 l/m2h. The obtained
turbidity decrease was in the range of 50-99 % and total amount of
suspended solids was removed.
Abstract: Main objective of this paper is to establish a link
between inertial forces of the bearings used in construction of wind
power plant and its behavior. Using bearings with lower inertial
forces has the immediate effect of decreasing inertia rotor system,
with significant results in increased energy efficiency, due to
decreased friction forces between rollers and raceways. The F.E.M.
analysis shows the appearance of uniform contact stress at the ends of
the rollers, demonstrated the necessity of production of low mass
bearings. Favorable results are expected in the economic field, by
reducing material consumption and by increasing the durability of
bearings. Using low mass bearings with hollow rollers instead of
solid rollers has an impact on working temperature, on vibrations and
noise which decrease. Implementation of types of hollow rollers of
cylindrical tubular type, instead of expensive rollers with logarithmic
profile, will bring significant inertial forces decrease with large
benefits in behavior of wind power plant.
Abstract: Indonesia has experienced annual forest fires that have
rapidly destroyed and degraded its forests. Fires in the peat swamp
forests of Riau Province, have set the stage for problems to worsen,
this being the ecosystem most prone to fires (which are also the most
difficult, to extinguish). Despite various efforts to curb deforestation,
and forest degradation processes, severe forest fires are still
occurring. To find an effective solution, the basic causes of the
problems must be identified. It is therefore critical to have an indepth
understanding of the underlying causal factors that have
contributed to deforestation and forest degradation as a whole, in
order to attain reductions in their rates. An assessment of the drivers of deforestation and forest
degradation was carried out, in order to design and implement
measures that could slow these destructive processes. Research was
conducted in Giam Siak Kecil–Bukit Batu Biosphere Reserve
(GSKBB BR), in the Riau Province of Sumatera, Indonesia. A
biosphere reserve was selected as the study site because such reserves
aim to reconcile conservation with sustainable development. A
biosphere reserve should promote a range of local human activities,
together with development values that are in line spatially and
economically with the area conservation values, through use of a
zoning system. Moreover, GSKBB BR is an area with vast peatlands,
and is experiencing forest fires annually. Various factors were
analysed to assess the drivers of deforestation and forest degradation
in GSKBB BR; data were collected from focus group discussions
with stakeholders, key informant interviews with key stakeholders,
field observation and a literature review. Landsat satellite imagery was used to map forest-cover changes
for various periods. Analysis of landsat images, taken during the
period 2010-2014, revealed that within the non-protected area of core
zone, there was a trend towards decreasing peat swamp forest areas,
increasing land clearance, and increasing areas of community oilpalm
and rubber plantations. Fire was used for land clearing and most
of the forest fires occurred in the most populous area (the transition
area). The study found a relationship between the deforested/
degraded areas, and certain distance variables, i.e. distance from
roads, villages and the borders between the core area and the buffer
zone. The further the distance from the core area of the reserve, the
higher was the degree of deforestation and forest degradation. Research findings suggested that agricultural expansion may be
the direct cause of deforestation and forest degradation in the reserve,
whereas socio-economic factors were the underlying driver of forest
cover changes; such factors consisting of a combination of sociocultural,
infrastructural, technological, institutional (policy and governance), demographic (population pressure) and economic
(market demand) considerations. These findings indicated that local
factors/problems were the critical causes of deforestation and
degradation in GSKBB BR. This research therefore concluded that
reductions in deforestation and forest degradation in GSKBB BR
could be achieved through ‘local actor’-tailored approaches such as
community empowerment.