Abstract: Cement-based grouts has been used successfully to
repair cracks in many concrete structures such as bridges, tunnels,
buildings and to consolidate soils or rock foundations. In the present
study the rheological characterization of cement grout with
water/binder ratio (W/B) is fixed at 0.5. The effect of the replacement
of cement by bentonite (2 to 10% wt) in presence of superplasticizer
(0.5% wt) was investigated. Several rheological tests were carried out
by using controlled-stress rheometer equipped with vane geometry in
temperature of 20°C. To highlight the influence of bentonite and
superplasticizer on the rheological behavior of grout cement, various
flow tests in a range of shear rate from 0 to 200 s-1 were observed.
Cement grout showed a non-Newtonian viscosity behavior at all
concentrations of bentonite. Three parameter model Herschel-
Bulkley was chosen for fitting of experimental data. Based on the
values of correlation coefficients of the estimated parameters, The
Herschel-Bulkley law model well described the rheological behavior
of the grouts. Test results showed that the dosage of bentonite
increases the viscosity and yield stress of the system and introduces
more thixotropy. While the addition of both bentonite and
superplasticizer with cement grout improve significantly the fluidity
and reduced the yield stress due to the action of dispersion of SP.
Abstract: Different services based on different switching
techniques in wireless networks leads to drastic changes in the
properties of network traffic. Because of these diversities in services,
network traffic is expected to undergo qualitative and quantitative
variations. Hence, assumption of traffic characteristics and the
prediction of network events become more complex for the wireless
networks. In this paper, the traffic characteristics have been studied
by collecting traces from the mobile switching centre (MSC). The
traces include initiation and termination time, originating node, home
station id, foreign station id. Traffic parameters namely, call interarrival
and holding times were estimated statistically. The results
show that call inter-arrival and distribution time in this wireless
network is heavy-tailed and follow gamma distributions. They are
asymptotically long-range dependent. It is also found that the call
holding times are best fitted with lognormal distribution. Based on
these observations, an analytical model for performance estimation is
also proposed.
Abstract: Renewable energy is derived from natural processes
that are replenished constantly. Included in the definition is
electricity and heat generated from solar, wind, ocean, hydropower,
biomass, geothermal resources, and bio-fuels and hydrogen derived
from renewable resources. Each of these sources has unique
characteristics which influence how and where they are used. This
paper presents the modeling the simulation of solar and hydro hybrid
energy sources in MATLAB/SIMULINK environment. It simulates
all quantities of Hybrid Electrical Power system (HEPS) such as AC
output current of the inverter that injected to the load/grid, load
current, grid current. It also simulates power output from PV and
Hydraulic Turbine Generator (HTG), power delivered to or from grid
and finally power factor of the inverter for PV, HTG and grid. The
proposed circuit uses instantaneous p-q (real-imaginary) power
theory.
Abstract: In this paper a scheme is proposed for generating
a programmable current reference which can be implemented
in the CMOS technology. The current can be varied over a
wide range by changing an external voltage applied to one
of the control gates of FGMOS (Floating Gate MOSFET).
For a range of supply voltages and temperature, CMOS
current reference is found to be dependent, this dependence
is compensated by subtracting two current outputs with the
same dependencies on the supply voltage and temperature.
The system performance is found to improve with the
use of FGMOS. Mathematical analysis of the proposed
circuit is done to establish supply voltage and temperature
independence. Simulation and performance evaluation of the
proposed current reference circuit is done using TANNER
EDA Tools. The current reference shows the supply and
temperature dependencies of 520 ppm/V and 312 ppm/oC,
respectively. The proposed current reference can operate down
to 0.9 V supply.
Abstract: With advances in solid-state power electronic devices
and microprocessors, various pulse-width-modulation (PWM)
techniques have been developed for industrial applications. This
paper presents the comparison of two different PWM techniques, the
sinusoidal PWM (SPWM) technique and the space-vector PWM
(SVPWM) technique applied to two level VSI for micro grid
applications. These two methods are compared by discussing their
ease of implementation and by analyzing the output harmonic spectra
of various output voltages (line-to-neutral voltages, and line-to-line
voltages) and their total harmonic distortion (THD). The SVPWM
technique in the under-modulation region can increase the
fundamental output voltage by 15.5% over the SPWM technique.
Abstract: The main goal of this paper was evaluate the effect of
diets containing different levels of probiotic on performance and milk
composition of lactating cows.
Eight Holstein cows were distributed in two 4x4 Latin square. The
diets were based on corn silage, concentrate and the treatment (0, 3, 6
or 9 grams of probiotic/animal/day). It was evaluated the dry matter
intake of nutrients, milk yield and composition.
The use of probiotics did not affect the nutrient intake (p>0.05)
neither the daily milk production or corrected to 4% fat (p>0.05).
However, it was observed that there was a significant fall in milk
composition with higher levels of probiotics supplementation.
These results emphasize the need of further studies with different
experimental designs or improve the number of Latin square with
longer periods of adaptation.
Abstract: In this paper family of multilevel inverter topology
with reduced number of power switches is presented. The proposed
inverter can generate both even and odd level. The proposed topology
is suitable for symmetric structure. The proposed symmetric inverter
results in reduction of power switches, power diode and gate driver
circuits and also it may further minimize the installation area and
cost. To prove the superiority of proposed topology is compared with
conventional topologies. The performance of this symmetric
multilevel inverter has been tested by computer based simulation and
prototype based experimental setup for nine-level inverter is
developed and results are verified.
Abstract: It’s an era of high competition, dynamism and
complexities which have forced organizations to change dramatically
due to rising customer expectations. Marketers are under constant
pressure to deliver finest to their customers. With the advent of
technology, marketers have identified latest advertising media
options to reach out to target audience. But the conventional ways of
print advertisements still holds a deeper penetration and coverage.
Various researchers and practitioners have studied the area of print
media advertising and have tried to identify and implement
advertisement effectiveness enablers. The purpose of this paper is to
suggest select enablers for print media in Indian context using an
integrated approach of review of literature and investigative
interviews with academicians and experts from the area of
advertising.
Abstract: Climate change will affect various aspects of
hydrological cycle such as rainfall. A change in rainfall will affect
flood magnitude and frequency in future which will affect the design
and operation of hydraulic structures. In this paper, trends in subhourly,
sub-daily, and daily extreme rainfall events from 18 rainfall
stations located in Tasmania, Australia are examined. Two nonparametric
tests (Mann-Kendall and Spearman’s Rho) are applied to
detect trends at 10%, 5%, and 1% significance levels. Sub-hourly (6,
12, 18, and 30 minutes) annual maximum rainfall events have been
found to experience statistically significant upward trends at 10%
level of significance. However, sub-daily durations (1 hour, 3 and 12
hours) exhibit decreasing trends and no trends exists for longer
duration rainfall events (e.g. 24 and 72 hours). Some of the durations
(e.g. 6 minutes and 6 hours) show similar results (with upward
trends) for both the tests. For 12, 18, 60 minutes and 3 hours
durations both the tests show similar downward trends. This finding
has important implication for Tasmania in the design of urban
infrastructure where shorter duration rainfall events are more relevant
for smaller urban catchments such as parking lots, roof catchments
and smaller sub-divisions.
Abstract: This study discovers a novel framework of individual
level technology adoption known as I-P (Individual- Privacy) towards
health information application in Smart National Identity Card. Many
countries introduced smart national identity card (SNIC) with various
applications such as health information application embedded inside
it. However, the degree to which citizens accept and use some of the
embedded applications in smart national identity remains unknown to
many governments and application providers as well. Moreover, the
factors of trust, perceived risk, Privacy concern and perceived
credibility need to be incorporated into more comprehensive models
such as extended Unified Theory of Acceptance and Use of
Technology known as UTAUT2. UTAUT2 is a mainly widespread
and leading theory up to now. This research identifies factors
affecting the citizens’ behavioural intention to use health information
application embedded in SNIC and extends better understanding on
the relevant factors that the government and the application providers
would need to consider in predicting citizens’ new technology
acceptance in the future. We propose a conceptual framework by
combining the UTAUT2 and Privacy Calculus Model constructs and
also adding perceived credibility as a new variable. The proposed
framework may provide assistance to any government planning,
decision, and policy makers involving e-government projects.
Empirical study may be conducted in the future to provide proof and
empirically validate this I-P framework.
Abstract: Multiwall carbon nanotubes, prepared by chemical
vapor deposition, have an average diameter of 60-100 nm as shown
by High Resolution Transmittance Electron Microscope, HR-TEM.
The Multiwall carbon nanotubes (MWCNTs) were further
characterized using X-ray Diffraction and Raman Spectroscopy.
Mercury uptake capacity of MWCNTs was studied using batch
adsorption method at different concentration ranges up to 150 ppm.
Mercury concentration (before and after the treatment) was measured
using cold vapor atomic absorption spectroscopy. The effect of time,
concentration, pH and adsorbent dose were studied. MWCNT were
found to perform complete absorption in the sub-ppm concentrations
(parts per billion levels) while for high concentrations, the adsorption
efficiency was 92% at the optimum conditions; 0.1 g of the adsorbent
at 150 ppm mercury (II) solution. The adsorption of mercury on
MWCNTs was found to follow the Freundlich adsorption isotherm
and the pseudo-second order kinetic model.
Abstract: Fuzzy systems have been successfully used for
exchange rate forecasting. However, fuzzy system is very confusing
and complex to be designed by an expert, as there is a large set of
parameters (fuzzy knowledge base) that must be selected, it is not a
simple task to select the appropriate fuzzy knowledge base for an
exchange rate forecasting. The researchers often look the effect of
fuzzy knowledge base on the performances of fuzzy system
forecasting. This paper proposes a genetic fuzzy predictor to forecast
the future value of daily US Dollar/Euro exchange rate time’s series.
A range of methodologies based on a set of fuzzy predictor’s which
allow the forecasting of the same time series, but with a different
fuzzy partition. Each fuzzy predictor is built from two stages, where
each stage is performed by a real genetic algorithm.
Abstract: Natural gas, as one of the most important sources of
energy for many of the industrial and domestic users all over the
world, has a complex, huge supply chain which is in need of heavy
investments in all the phases of exploration, extraction, production,
transportation, storage and distribution. The main purpose of supply
chain is to meet customers’ need efficiently and with minimum cost.
In this study, with the aim of minimizing economic costs, different
levels of natural gas supply chain in the form of a multi-echelon,
multi-period fuzzy linear programming have been modeled. In this
model, different constraints including constraints on demand
satisfaction, capacity, input/output balance and presence/absence of a
path have been defined. The obtained results suggest efficiency of the
recommended model in optimal allocation and reduction of supply
chain costs.
Abstract: The phased-array ultrasound transducer types are
utilities for medical ultrasonography as well as optical imaging.
However, their discontinuity characteristic limits the applications due
to the artifacts contaminated into the reconstructed images. Because
of the effects of the ultrasound pressure field pattern to the echo
ultrasonic waves as well as the optical modulated signal, the side
lobes of the focused ultrasound beam induced by discontinuity of the
phased-array ultrasound transducer might the reason of the artifacts.
In this paper, a simple method in approach of numerical simulation
was used to investigate the limitation of discontinuity of the elements
in phased-array ultrasound transducer and their effects to the
ultrasound pressure field. Take into account the change of ultrasound
pressure field patterns in the conditions of variation of the pitches
between elements of the phased-array ultrasound transducer, the
appropriated parameters for phased-array ultrasound transducer
design were asserted quantitatively.
Abstract: The purpose of this project is to carry out an analysis
and determine the profile of actual lean manufacturing processes in
the Metropolitan Area of Bucaramanga. Through the analysis of
qualitative and quantitative variables it was possible to establish how
these manufacturers develop production practices that ensure their
competitiveness and productivity in the market.
In this study, a random sample of metallurgic and wrought iron
companies was applied, following which a quantitative focus and
analysis was used to formulate a qualitative methodology for
measuring the level of lean manufacturing procedures in the industry.
A qualitative evaluation was also carried out through a multivariate
analysis using the Numerical Taxonomy System (NTSYS) program
which should allow for the determination of Lean Manufacturing
profiles.
Through the results it was possible to observe how the companies
in the sector are doing with respect to Lean Manufacturing Practices,
as well as identify the level of management that these companies
practice with respect to this topic. In addition, it was possible to
ascertain that there is no one dominant profile in the sector when it
comes to Lean Manufacturing.
It was established that the companies in the metallurgic and
wrought iron industry show low levels of Lean Manufacturing
implementation. Each one carries out diverse actions that are
insufficient to consolidate a sectoral strategy for developing a
competitive advantage which enables them to tie together a
production strategy.
Abstract: Recently, an increasing number of researchers have
been focusing on working out realistic solutions to sustainability
problems. As sustainability issues gain higher importance for
organisations, the management of such decisions becomes critical.
Knowledge representation is a fundamental issue of complex
knowledge based systems. Many types of sustainability problems
would benefit from models based on experts’ knowledge. Cognitive
maps have been used for analyzing and aiding decision making. A
cognitive map can be made of almost any system or problem. A
fuzzy cognitive map (FCM) can successfully represent knowledge
and human experience, introducing concepts to represent the essential
elements and the cause and effect relationships among the concepts to
model the behaviour of any system. Integrated waste management
systems (IWMS) are complex systems that can be decomposed to
non-related and related subsystems and elements, where many factors
have to be taken into consideration that may be complementary,
contradictory, and competitive; these factors influence each other and
determine the overall decision process of the system. The goal of the
present paper is to construct an efficient IWMS which considers
various factors. The authors’ intention is to propose an expert based
system design approach for implementing expert decision support in
the area of IWMSs and introduces an appropriate methodology for
the development and analysis of group FCM. A framework for such a
methodology consisting of the development and application phases is
presented.
Abstract: The global solved problem is the calculation of the
parameters of ceramic material from a set of destruction tests of
ceramic heads of total hip joint endoprosthesis. The standard way of
calculation of the material parameters consists in carrying out a set of
3 or 4 point bending tests of specimens cut out from parts of the
ceramic material to be analysed. In case of ceramic heads, it is not
possible to cut out specimens of required dimensions because the
heads are too small (if the cut out specimens were smaller than the
normalised ones, the material parameters derived from them would
exhibit higher strength values than those which the given ceramic
material really has). A special destruction device for heads
destruction was designed and the solved local problem is the
modification of this destructive device based on the analysis of
tensile stress in the head for two different values of the depth of the
conical hole in the head. The goal of device modification is a shift of
the location with extreme value of σ1max from the region of head’s
hole bottom to its opening. This modification will increase the
credibility of the obtained material properties of bioceramics, which
will be determined from a set of head destructions using the Weibull
weakest link theory.
Abstract: Stochastic User Equilibrium (SUE) model is a widely
used traffic assignment model in transportation planning, which is
regarded more advanced than Deterministic User Equilibrium (DUE)
model. However, a problem exists that the performance of the SUE
model depends on its error term parameter. The objective of this
paper is to propose a systematic method of determining the
appropriate error term parameter value for the SUE model. First, the
significance of the parameter is explored through a numerical
example. Second, the parameter calibration method is developed
based on the Logit-based route choice model. The calibration process
is realized through multiple nonlinear regression, using sequential
quadratic programming combined with least square method. Finally,
case analysis is conducted to demonstrate the application of the
calibration process and validate the better performance of the SUE
model calibrated by the proposed method compared to the SUE
models under other parameter values and the DUE model.
Abstract: This paper presents a real-time visualization technique
and filtering of classified LiDAR point clouds. The visualization is
capable of displaying filtered information organized in layers by the
classification attribute saved within LiDAR datasets. We explain the
used data structure and data management, which enables real-time
presentation of layered LiDAR data. Real-time visualization is
achieved with LOD optimization based on the distance from the
observer without loss of quality. The filtering process is done in two
steps and is entirely executed on the GPU and implemented using
programmable shaders.
Abstract: 3D part library is an ideal approach to reuse the
existing design and thus facilitates the modeling process, which will
enhance the efficiency. In this paper, we implemented the thought on
the SolidWorks platform. The system supports the functions of type
and parameter selection, 3D template driving and part assembly.
Finally, BOM is exported in Excel format. Experiment shows that our
method can satisfy the requirement of die and mold designers.