Abstract: The aim of this paper is to perform experimental
modal analysis (EMA) of reinforced concrete (RC) square slabs.
EMA is the process of determining the modal parameters (Natural
Frequencies, damping factors, modal vectors) of a structure from a
set of frequency response functions FRFs (curve fitting). Although,
experimental modal analysis (or modal testing) has grown steadily in
popularity since the advent of the digital FFT spectrum analyzer in
the early 1970’s, studying all types of members and materials using
such method have not yet been well documented. Therefore, in this
work, experimental tests were conducted on RC square slab
specimens of dimensions 600mm x 600mmx 40mm. Experimental
analysis was based on freely supported boundary condition.
Moreover, impact testing as a fast and economical means of finding
the modes of vibration of a structure was used during the
experiments. In addition, Pico Scope 6 device and MATLAB
software were used to acquire data, analyze and plot Frequency
Response Function (FRF). The experimental natural frequencies
which were extracted from measurements exhibit good agreement
with analytical predictions. It is showed that EMA method can be
usefully employed to investigate the dynamic behavior of RC slabs.
Abstract: The present study was undertaken to investigate the
effect of aging parameters (time and temperature) on the mechanical
properties of Be-and/or Zr- treated Al-Mg-Zn (7075) alloys. Ultimate
tensile strength, 0.5% offset yield strength and % elongation
measurements were carried out on specimens prepared from cast and
heat treated 7075 alloys containing Be and/or Zr. Different aging
treatment were carried out for the as solution treated (SHT)
specimens (after quenching in warm water). The specimens were
aged at different conditions; Natural and artificial aging was carried
out at room temperature, 120C, 150C, 180C and 220C for different
periods of time. Duplex aging was performed for SHT conditions
(pre-aged at different time and temperature followed by high
temperature aging). Ultimate tensile strength, yield strength and %
elongation data results as a function of different aging parameters are
analysed. A statistical design of experiments (DOE) approach using
fractional factorial design is applied to acquire an understanding of
the effects of these variables and their interactions on the mechanical
properties of Be- and/or Zr- treated 7075 alloys. Mathematical
models are developed to relate the alloy mechanical properties with
the different aging parameters.
Abstract: The western Tombolo of the Giens peninsula in
southern France, known as Almanarre beach, is subject to coastal
erosion. We are trying to use computer simulation in order to propose
solutions to stop this erosion. Our aim was first to determine the main
factors for this erosion and successfully apply a coupled hydrosedimentological
numerical model based on observations and
measurements that have been performed on the site for decades.
We have gathered all available information and data about waves,
winds, currents, tides, bathymetry, coastal line, and sediments
concerning the site. These have been divided into two sets: one
devoted to calibrating a numerical model using Mike 21 software, the
other to serve as a reference in order to numerically compare the
present situation to what it could be if we implemented different
types of underwater constructions.
This paper presents the first part of the study: selecting and
melting different sources into a coherent data basis, identifying the
main erosion factors, and calibrating the coupled software model
against the selected reference period.
Our results bring calibration of the numerical model with good
fitting coefficients. They also show that the winter South-Western
storm events conjugated to depressive weather conditions constitute a
major factor of erosion, mainly due to wave impact in the northern
part of the Almanarre beach. Together, current and wind impact is
shown negligible.
Abstract: The present work aims to throw light on the effects of
arcing in air on the surface state of contact pastilles made of silvernickel
Ag-Ni (60/40). Also, the photoelectric emission from these
electrical contacts has been investigated in the spectral range of 196-
256 nm. In order to study the effects of arcing on the EWF, the
metallic samples were subjected to electrical arcs in air, at
atmospheric pressure and room temperature, after that, they have
been introduced into the vacuum chamber of an experimental UHV
set-up for EWF measurements. Both Fowler method of isothermal
curves and linearized Fowler plots were used for the measurement of
the EWF by the photoelectric effect.
It has been found that the EWF varies with the number of applied
arcs. Thus, after 500 arcs in air, the observed EWF increasing is
probably due to progressive inclusion of oxide on alloy surface.
Microscopic examination is necessary to get better understandings on
EWF of silver alloys, for both virgin and arced electrical contacts.
Abstract: The present study was undertaken to investigate the
effect of pre-aging and aging parameters (time and temperature) on
the mechanical properties of Al-Mg-Zn (7075) alloys. Ultimate
tensile strength, 0.5% offset yield strength and % elongation
measurements were carried out on specimens prepared from cast and
heat treated 7075 alloys. Aging treatments were carried out for the as
solution treated (SHT) specimens (after quenching in warm water).
The specimens were aged at different conditions; Natural aging was
carried out at room temperature for different periods of time. Double
aging was performed for SHT conditions (pre-aged at different time
and temperature followed by high temperature aging). Ultimate
tensile strength, yield strength and % elongation as a function of
different pre-aging and aging parameters are analyzed to acquire an
understanding of the effects of these variables and their interactions
on the mechanical properties of Be-treated 7075 alloys.
Abstract: Motion Tracking and Stereo Vision are complicated,
albeit well-understood problems in computer vision. Existing
softwares that combine the two approaches to perform stereo motion
tracking typically employ complicated and computationally expensive
procedures. The purpose of this study is to create a simple and
effective solution capable of combining the two approaches. The
study aims to explore a strategy to combine the two techniques
of two-dimensional motion tracking using Kalman Filter; and depth
detection of object using Stereo Vision. In conventional approaches
objects in the scene of interest are observed using a single camera.
However for Stereo Motion Tracking; the scene of interest is
observed using video feeds from two calibrated cameras. Using two
simultaneous measurements from the two cameras a calculation for
the depth of the object from the plane containing the cameras is made.
The approach attempts to capture the entire three-dimensional spatial
information of each object at the scene and represent it through a
software estimator object. In discrete intervals, the estimator tracks
object motion in the plane parallel to plane containing cameras and
updates the perpendicular distance value of the object from the plane
containing the cameras as depth. The ability to efficiently track
the motion of objects in three-dimensional space using a simplified
approach could prove to be an indispensable tool in a variety of
surveillance scenarios. The approach may find application from high
security surveillance scenes such as premises of bank vaults, prisons
or other detention facilities; to low cost applications in supermarkets
and car parking lots.
Abstract: Equal channel angular pressing (ECAP) of
commercial Al-Mg-Si alloy was conducted using two strain rates.
The ECAP processing was conducted at room temperature and at
250°C. Route A was adopted up to a total number of four passes in
the present work. Structural evolution of the aluminum alloy discs
was investigated before and after ECAP processing using optical
microscopy (OM). Following ECAP, simple compression tests and
Vicker’s hardness were performed. OM micrographs showed that, the
average grain size of the as-received Al-Mg-Si disc tends to be larger
than the size of the ECAP processed discs. Moreover, significant
difference in the grain morphologies of the as-received and processed
discs was observed. Intensity of deformation was observed via the
alignment of the Al-Mg-Si consolidated particles (grains) in the
direction of shear, which increased with increasing the number of
passes via ECAP. Increasing the number of passes up to 4 resulted in
increasing the grains aspect ratio up to ~5. It was found that the
pressing temperature has a significant influence on the
microstructure, Hv-values, and compressive strength of the processed
discs. Hardness measurements demonstrated that 1-pass resulted in
increase of Hv-value by 42% compared to that of the as-received
alloy. 4-passes of ECAP processing resulted in additional increase in
the Hv-value. A similar trend was observed for the yield and
compressive strength. Experimental data of the Hv-values
demonstrated that there is a lack of any significant dependence on the
processing strain rate.
Abstract: An existing RC building in Madinah is seismically
evaluated with and without infill wall. Four model systems have been
considered i.e. model I (no infill), model IIA (strut infill-update from
field test), model IIB (strut infill- ASCE/SEI 41) and model IIC (strut
infill-Soft storey- ASCE/SEI 41). Three dimensional pushover
analyses have been carried out using SAP2000 software
incorporating inelastic material behavior for concrete, steel and infill
walls. Infill wall has been modeled as equivalent strut according to
suggested equation matching field test measurements and to the
ASCE/SEI 41 equation. The effect of building modeling on the
performance point as well as capacity and demand spectra due to EQ
design spectrum function in Madinah area has been investigated. The
response modification factor (R) for the 5 story RC building is
evaluated from capacity and demand spectra (ATC-40) for the
studied models. The results are summarized and discussed.
Abstract: Early pre-code reinforced concrete structures present
undetermined resistance to earthquakes. This situation is particularly
unacceptable in the case of essential structures, such as healthcare
structures and pilgrims' houses. Amongst these, an existing old RC
building in Madinah city (KSA) is seismically evaluated with and
without infill wall and their dynamic characteristics are compared
with measured values in the field using ambient vibration
measurements (AVM). After updating the mathematical models for
this building with the experimental results, three dimensional
pushover analysis (Nonlinear static analysis) was carried out using
commercial structural analysis software incorporating inelastic
material properties for concrete, infill and steel. The purpose of this
analysis is to evaluate the expected performance of structural systems
by estimating, strength and deformation demands in design, and
comparing these demands to available capacities at the performance
levels of interest. The results summarized and discussed.
Abstract: One of the major difficulties introduced with wind
power penetration is the inherent uncertainty in production originating
from uncertain wind conditions. This uncertainty impacts many
different aspects of power system operation, especially the balancing
power requirements. For this reason, in power system development
planing, it is necessary to evaluate the potential uncertainty in future
wind power generation. For this purpose, simulation models are
required, reproducing the performance of wind power forecasts.
This paper presents a wind power forecast error simulation models
which are based on the stochastic process simulation. Proposed
models capture the most important statistical parameters recognized
in wind power forecast error time series. Furthermore, two distinct
models are presented based on data availability. First model uses
wind speed measurements on potential or existing wind power plant
locations, while the seconds model uses statistical distribution of wind
speeds.
Abstract: Measurements and quantitative analysis of kinematic
parameters of human hand movements have an important role in
different areas such as hand function rehabilitation, modeling of
multi-digits robotic hands, and the development of machine-man
interfaces. In this paper the assessment and evaluation of the reachto-
grasp movement by using computerized and robot-assisted method
is described. Experiment involved the measurements of hand
positions of seven healthy subjects during grasping three objects of
different shapes and sizes. Results showed that three dominant phases
of reach-to-grasp movements could be clearly identified.
Abstract: In this paper, extract of papaya leaves are used as a
natural dye and combined by variations of solvent concentration
applied on DSSC (Dye-Sensitized Solar Cell). Indonesian geographic
located on the equator line occasions the magnitude of the potential
to develop organic solar cells made from extracts of chlorophyll as a
substitute for inorganic materials or synthetic dye on DSSC material.
Dye serves as absorbing photons which are then converted into
electrical energy. A conductive coated glass layer called TCO
(Transparent Conductive Oxide) is used as a substrate of electrode.
TiO2 nanoparticles as binding dye molecules, redox couple iodide/
tri-iodide as the electrolyte and carbon as the counter electrode in the
DSSC are used. TiO2 nanoparticles, organic dyes, electrolytes, and
counter electrode are arranged and combined with the layered
structure of the photo-catalyst absorption layer. Dye absorption
measurements using a spectrophotometer at 400-800 nm light
spectrum produces a total amount of chlorophyll 80.076 mg/l. The
test cell at 7 watt LED light with 5000 lux luminescence was
obtained Voc and Isc of 235.5 mV and 14 μA, respectively.
Abstract: Starting in 2020, an EU-wide CO2-limitation of
95 g/km is scheduled for the average of an OEMs passenger car fleet.
Taking that into consideration additional improvement measures of
the Diesel cycle are necessary in order to reduce fuel consumption
and emissions while boosting, or at the least, keeping performance
values at the same time.
The present article deals with the possibilities of an optimized
air/water charge air cooler, also called iCAC (indirect Charge Air
Cooler) for a Diesel passenger car amongst extreme-boundary
conditions. In this context, the precise objective was to show the
impact of improved intercooling with reference to the engine working
process (fuel consumption and NOx-emissions). Several extremeboundaries
- e.g. varying ambient temperatures or mountainous
routes - that will become very important in the near future regarding
RDE (Real Driving emissions) were subject of the investigation.
With the introduction of RDE in 2017 (EU6c measure), the
controversial NEDC (New European Driving Cycle) will belong to
the past and the OEMs will have to avoid harmful emissions in any
conceivable real life situation.
This is certainly going to lead to optimization-measurements at the
powertrain, which again is going to make the implementation of
iCACs, presently solely used for the premium class, more and more
attractive for compact class cars. The investigations showed a benefit
in FC between 1 and 3% for the iCAC in real world conditions.
Abstract: Water spray cooling is a technique typically used in
heat treatment and other metallurgical processes where controlled
temperature regimes are required. Water spray cooling is used in
static (without movement) or dynamic (with movement of the steel
plate) regimes. The static regime is notable for the fixed position of
the hot steel plate and fixed spray nozzle. This regime is typical for
quenching systems focused on heat treatment of the steel plate. The
second application of spray cooling is the dynamic regime. The
dynamic regime is notable for its static section cooling system and
moving steel plate. This regime is used in rolling and finishing mills.
The fixed position of cooling sections with nozzles and the
movement of the steel plate produce nonhomogeneous water
distribution on the steel plate. The length of cooling sections and
placement of water nozzles in combination with the nonhomogeneity
of water distribution lead to discontinued or interrupted cooling
conditions. The impact of static and dynamic regimes on cooling
intensity and the heat transfer coefficient during the cooling process
of steel plates is an important issue.
Heat treatment of steel is accompanied by oxide scale growth. The
oxide scale layers can significantly modify the cooling properties and
intensity during the cooling. The combination of static and dynamic
(section) regimes with the variable thickness of the oxide scale layer
on the steel surface impact the final cooling intensity. The study of
the influence of the oxide scale layers with different cooling regimes
was carried out using experimental measurements and numerical
analysis. The experimental measurements compared both types of
cooling regimes and the cooling of scale-free surfaces and oxidized
surfaces. A numerical analysis was prepared to simulate the cooling
process with different conditions of the section and samples with
different oxide scale layers.
Abstract: In this study which has been conducted in Akçasu
Forest Range District of Devrek Forest Directorate; 3 methods (weed
control with labourer power, cover removal with Hitachi F20
Excavator, and weed control with agricultural equipment mounted on
a Ferguson 240S agriculture tractor) were utilized in weed control
efforts in regeneration of degraded oriental beech forests have been
compared. In this respect, 3 methods have been compared by
determining certain work hours and standard durations of unit areas
(1 hectare). For this purpose, evaluating the tasks made with human
and machine force from the aspects of duration, productivity and
costs, it has been aimed to determine the most productive method in
accordance with the actual ecological conditions of research field.
Within the scope of the study, the time studies have been conducted
for 3 methods used in weed control efforts. While carrying out those
studies, the performed implementations have been evaluated by
dividing them into business stages. Also, the actual data have been
used while calculating the cost accounts. In those calculations, the
latest formulas and equations which are also used in developed
countries have been utilized. The variance of analysis (ANOVA) was
used in order to determine whether there is any statistically
significant difference among obtained results, and the Duncan test
was used for grouping if there is significant difference. According to
the measurements and findings carried out within the scope of this
study, it has been found during living cover removal efforts in
regeneration efforts in demolished oriental beech forests that the
removal of weed layer in 1 hectare of field has taken 920 hours with
labourer force, 15.1 hours with excavator and 60 hours with an
equipment mounted on a tractor. On the other hand, it has been
determined that the cost of removal of living cover in unit area (1
hectare) was 3220.00 TL for labourer power, 1250 TL for excavator
and 1825 TL for equipment mounted on a tractor.
According to the obtained results, it has been found that the
utilization of excavator in weed control effort in regeneration of
degraded oriental beech regions under actual ecological conditions of
research field has been found to be more productive from both of
aspects of duration and costs. These determinations carried out
should be repeated in weed control efforts in degraded forest fields
with different ecological conditions, it is compulsory for finding the
most efficient weed control method. These findings will light the way
of technical staff of forestry directorate in determination of the most
effective and economic weed control method. Thus, the more actual
data will be used while preparing the weed control budgets, and there
will be significant contributions to national economy. Also the results of this and similar studies are very important for developing the policies for our forestry in short and long term.
Abstract: The levels of maximum power density of GSM
signals in the cities of Lagos, Ibadan and Abuja were studied.
Measurements were made with a calibrated hand held spectrum
analyzer 200m away from 271 base stations, at 1.2m to the ground
level. The maximum GSM 900 signal power density was
139.63μW/m2 in Lagos, 162.49μW/m2 in Ibadan and 5411.26μW/m2
in Abuja. Also, the maximum GSM 1800 signal power density was
296.82μW/m2 in Lagos, 116.82μW/m2 in Ibadan and 1263.00μW/m2
in Abuja. The level of power density of GSM 900 and GSM 1800
signals in the cities of Lagos, Ibadan and Abuja are far less than the
recommended value of 4.5W/m2 for GSM 900 and 9.0 W/m2 for
GSM 1800 by the ICNRP guideline. It can be concluded that
exposure to GSM signals in these cities cannot contribute to the
health detriments caused by thermal effects of radiofrequency
radiation.
Abstract: In this study, epoxy composite specimens reinforced
with multi-walled carbon nanotube filler were fabricated using shear
mixer and ultra-sonication processor. The mechanical and thermal
properties of the fabricated specimens were measured and evaluated.
From the electron microscope images and the results from the
measurements of tensile strengths, the specimens having 0.6 wt%
nanotube content show better dispersion and higher strength than those
of the other specimens. The Young’s moduli of the specimens
increased as the contents of the nanotube filler in the matrix were
increased. The specimen having a 0.6 wt% nanotube filler content
showed higher thermal conductivity than that of the other specimens.
While, in the measurement of thermal expansion, specimens having
0.4 and 0.6 wt% filler contents showed a lower value of thermal
expansion than that of the other specimens. On the basis of the
measured and evaluated properties of the composites, we believe that
the simple and time-saving fabrication process used in this study was
sufficient to obtain improved properties of the specimens.
Abstract: Monocopter is a single-wing rotary flying vehicle
which has the capability of hovering. This flying vehicle includes two
dynamic parts in which more efficiency can be expected rather than
other Micro UAVs due to the extended area of wing compared to its
fuselage. Low cost and simple mechanism in comparison to other
vehicles such as helicopter are the most important specifications of
this flying vehicle.
In the previous paper we discussed the introduction of the final
system but in this paper, the experimental design process of
Monocopter and its control algorithm has been investigated in
general. Also the editorial bugs in the previous article have been
corrected and some translational ambiguities have been resolved.
Initially by constructing several prototypes and carrying out many
flight tests the main design parameters of this air vehicle were
obtained by experimental measurements. Eventually the required
main monocopter for this project was constructed. After construction
of the monocopter in order to design, implementation and testing of
control algorithms first a simple optic system used for determining
the heading angle. After doing numerous tests on Test Stand, the
control algorithm designed and timing of applying control inputs
adjusted. Then other control parameters of system were tuned in
flight tests. Eventually the final control system designed and
implemented using the AHRS sensor and the final operational tests
performed successfully.
Abstract: Aerated concrete is a load bearing construction
material, which has high heat insulation parameters. Walls can be
erected from aerated concrete masonry constructions and in perfect
circumstances additional heat insulation is not required. The most
common problem in aerated concrete heat insulation properties is the
humidity distribution throughout the cross section of the masonry
elements as well as proper and conducted drying process of the
aerated concrete construction because only dry aerated concrete
masonry constructions can reach high heat insulation parameters.
In order to monitor drying process of the masonry and detect
humidity distribution throughout the cross section of aerated concrete
masonry construction application of electrical impedance
spectrometry is applied. Further test results and methodology of this
non-destructive testing method is described in this paper.
Abstract: Violet Sr–Al–O:Eu2+ phosphor particles were
synthesized from a metal–ethylenediaminetetraacetic acid (EDTA)
solution of Sr, Al, Eu, and particulate alumina via spray drying and
sintering in a reducing atmosphere. The crystal structures and emission
properties at 85–300 K were investigated. The composition of the
violet Sr–Al–O:Eu2+ phosphor particles was determined from various
Sr–Al–O:Eu2+ phosphors by their emission properties’ dependence
on temperature. The highly crystalline SrAl12O19:Eu2+ emission phases
were confirmed by their crystallite sizes and the activation energies for
the 4f5d–8S7/2 transition of the Eu2+ ion. These results showed that the
material identification for the violet Sr–Al–O:Eu2+ phosphor was
accomplished by the low-temperature luminescence measurements.