Abstract: All current experimental methods for determination of
stress intensity factors are based on the assumption that the state of
stress near the crack tip is plane stress. Therefore, these methods rely
on strain and displacement measurements made outside the near
crack tip region affected by the three-dimensional effects or by
process zone. In this paper, we develop and validate an experimental
procedure for the evaluation of stress intensity factors from the
measurements of the out-of-plane displacements in the surface area
controlled by 3D effects. The evaluation of stress intensity factors is
possible when the process zone is sufficiently small, and the
displacement field generated by the 3D effects is fully encapsulated
by K-dominance region.
Abstract: We report the microstructural and magnetic properties
of Ni50Mn39Sn11 and Ni50Mn36Sn14 ribbon Heusler alloys.
Experimental results were obtained by differential scanning
calorymetry, X-ray diffraction and vibrating sample magnetometry
techniques. The Ni-Mn-Sn system undergoes a martensitic structural
transformation in a wide temperature range. For example, for
Ni50Mn39Sn11 the start and finish temperatures of the martensitic and
austenite phase transformation for ribbon alloy were Ms=336K,
Mf=328K, As=335K and Af=343K whereas no structural
transformation is observed for Ni50Mn36Sn14 alloys. Magnetic
measurements show the typical ferromagnetic behavior with Curie
temperature 207 K at low applied field of 50 Oe. The complex
behavior exhibited by these Heusler alloys should be ascribed to the
strong coupling between magnetism and structure, being their
magnetic behavior determined by the distance between Mn atoms.
Abstract: Increasing prevalence of childhood obesity has
increased the interest in early and late indicators of gaining weight.
Cell blood counts may be indicators of pro-inflammatory states. The
aim was to evaluate associations of hematological parameters,
including hematocrit (HTC), hemoglobin, blood cell counts and their
indices with the degree of obesity in pediatric population. A total of
249; -139 morbidly obese (MO), 82 healthy normal weight (NW) and
28 overweight (OW) children were included into the scope of the
study. WHO BMI-for age percentiles were used to form age- and sexmatched
groups. Informed consent forms and the Ethics Committee
approval were obtained. Anthropometric measurements were
performed. Hematological parameters were determined. Statistical
analyses were performed using SPSS. The degree for statistical
significance was p≤0.05. Significant differences (p=0.000) between
waist-to-hip ratios and head-to- neck ratios (hnrs) of MO and NW
children were detected. A significant difference between hnrs of OW
and MO children (p=0.000) was observed. Red cell distribution width
(RDW) was higher in OW children than NW group (p=0.030). Such
finding couldn’t be detected between MO and NW groups. Increased
RDW was prominent in OW children. The decrease in mean
corpuscular hemoglobin concentration (MCHC) values in MO
children was sharper than the values in OW children (p=0.006 vs
p=0.042) compared to those in NW group. Statistically higher HTC
levels were observed between MO-NW (p=0.014), but none between
OW-NW. Though the cause-effect relationship between obesity and
erythrocyte indices still needs further investigation, alterations in
RDW, HTC, MCHC during obesity may be of significance in the
early life.
Abstract: A model was constructed to predict the amount of
solar radiation that will make contact with the surface of the earth in
a given location an hour into the future. This project was supported
by the Southern Company to determine at what specific times during
a given day of the year solar panels could be relied upon to produce
energy in sufficient quantities. Due to their ability as universal
function approximators, an artificial neural network was used to
estimate the nonlinear pattern of solar radiation, which utilized
measurements of weather conditions collected at the Griffin, Georgia
weather station as inputs. A number of network configurations and
training strategies were utilized, though a multilayer perceptron with
a variety of hidden nodes trained with the resilient propagation
algorithm consistently yielded the most accurate predictions. In
addition, a modeled direct normal irradiance field and adjacent
weather station data were used to bolster prediction accuracy. In later
trials, the solar radiation field was preprocessed with a discrete
wavelet transform with the aim of removing noise from the
measurements. The current model provides predictions of solar
radiation with a mean square error of 0.0042, though ongoing efforts
are being made to further improve the model’s accuracy.
Abstract: The arm length, hand length, hand breadth and middle
finger length of 1540 right-handed industrial workers of Haryana
state was used to assess the relationship between the upper limb
dimensions and stature. Initially, the data were analyzed using basic
univariate analysis and independent t-tests; then simple and multiple
linear regression models were used to estimate stature using SPSS
(version 17). There was a positive correlation between upper limb
measurements (hand length, hand breadth, arm length and middle
finger length) and stature (p < 0.01), which was highest for hand
length. The accuracy of stature prediction ranged from ± 54.897 mm
to ± 58.307 mm. The use of multiple regression equations gave better
results than simple regression equations. This study provides new
forensic standards for stature estimation from the upper limb
measurements of male industrial workers of Haryana (India). The
results of this research indicate that stature can be determined using
hand dimensions with accuracy, when only upper limb is available
due to any reasons likewise explosions, train/plane crashes, mutilated
bodies, etc. The regression formula derived in this study will be
useful for anatomists, archaeologists, anthropologists, design
engineers and forensic scientists for fairly prediction of stature using
regression equations.
Abstract: This paper presents system level CMOS solid-state
nanopore techniques enhancement for speedup next generation
molecular recording and high throughput channels. This discussion
also considers optimum number of base-pair (bp) measurements
through channel as an important role to enhance potential read
accuracy. Effective power consumption estimation offered suitable
range of multi-channel configuration. Nanopore bp extraction model
in statistical method could contribute higher read accuracy with
longer read-length (200 < read-length). Nanopore ionic current
switching with Time Multiplexing (TM) based multichannel readout
system contributed hardware savings.
Abstract: Interaction of Schiff base complexes of Iron and
Manganese: Iron [N, N’ Bis (5- (triphenyl phosphonium methyl)
salicylidene) -1, 2 ethanediamine) chloride, [Fe Salen]Cl; Manganese
[N, N’ Bis (5- (triphenyl phosphonium methyl) salicylidene) -1, 2
ethanediamine) acetate, were investigated by spectroscopic and
isothermal titration calorimetry techniques (ITC).
The absorbance spectra of complexes have shown hyper and
hypochromism in the presence of DNA that is indication of
interaction of complexes with DNA. The linear dichroism (LD)
measurements confirmed the bending of DNA in the presence of
complexes.
Furthermore, Isothermal titration calorimetry experiments
approved that complexes bound to DNA on the base of both
electrostatic and hydrophobic interactions. More, ITC profile exhibits
the existence of two binding phases for the complexes. Antibacterial
activity of ligand and complexes were tested in vitro to evaluate their
activity against the gram positive and negative bacteria.
Abstract: Two finite element (FEM) models are presented in
this paper to address the random nature of the response of glued
timber structures made of wood segments with variable elastic
moduli evaluated from 3600 indentation measurements. This total
database served to create the same number of ensembles as was the
number of segments in the tested beam. Statistics of these ensembles
were then assigned to given segments of beams and the Latin
Hypercube Sampling (LHS) method was called to perform 100
simulations resulting into the ensemble of 100 deflections subjected
to statistical evaluation. Here, a detailed geometrical arrangement of
individual segments in the laminated beam was considered in the
construction of two-dimensional FEM model subjected to in fourpoint
bending to comply with the laboratory tests. Since laboratory
measurements of local elastic moduli may in general suffer from a
significant experimental error, it appears advantageous to exploit the
full scale measurements of timber beams, i.e. deflections, to improve
their prior distributions with the help of the Bayesian statistical
method. This, however, requires an efficient computational model
when simulating the laboratory tests numerically. To this end, a
simplified model based on Mindlin’s beam theory was established.
The improved posterior distributions show that the most significant
change of the Young’s modulus distribution takes place in laminae in
the most strained zones, i.e. in the top and bottom layers within the
beam center region. Posterior distributions of moduli of elasticity
were subsequently utilized in the 2D FEM model and compared with
the original simulations.
Abstract: Ionic liquids consisting of a phosphonium cationic
moiety and a saccharinate anion are synthesized and compared with
their precursors, phosphonium chlorides, in reference to their
extraction efficiency towards L-lactic acid. On the base of
measurements of the acid and the water partitioning in the
equilibrium biphasic systems, the molar ratios between acid, water
and ionic liquid are estimated which allows to deduce the lactic acid
extractive pathway. The effect of a salting-out addition that
strengthens hydrophobicity in both phases is studied in view to reveal
the best biphasic system with respect to IL low toxicity and high
extraction efficiency.
Abstract: Nitrogen fertilizer is the most used and often the most
mismanaged nutrient input. Nitrogen management has tremendous
implications on crop productivity, quality and environmental
stewardship. Sufficient nitrogen is needed to optimum yield and
quality. Soil and in-season plant tissue testing for nitrogen status are
a time consuming and expensive process. Real time sensing of plant
nitrogen status can be a useful tool in managing nitrogen inputs. The
objectives of this project were to assess the reliability of remotely
sensed non-destructive plant nitrogen measurements compared to wet
chemistry data from sampled plant tissue, develop in-season nitrogen
recommendations based on remotely sensed data for improved
nitrogen use efficiency and assess the potential for determining yield
and quality from remotely sensed data. Very good correlations were
observed between early-season remotely sensed crop nitrogen status
and plant nitrogen concentrations and subsequent in-season fertilizer
recommendations. The transmittance/absorbance type meters gave
the most accurate readings. Early in-season fertilizer recommendation
would be to apply 40 kg nitrogen per hectare plus 15 kg nitrogen per
hectare for each unit difference measured with the SPAD meter
between the crop and reference area or 25 kg plus 13 kg per hectare
for each unit difference measured with the CCM 200. Once the crop
was sufficiently fertilized meter readings became inconclusive and
were of no benefit for determining nitrogen status, silage yield and
quality and grain yield and protein.
Abstract: The Al-MoO3-P-CdTe-Al MOS sandwich structures
were fabricated by vacuum deposition method on cleaned glass
substrates. Capacitance versus voltage measurements were performed
at different frequencies and sweep rates of applied voltages for oxide
and semiconductor films of different thicknesses. In the negative
voltage region of the C-V curve a high differential capacitance of the
semiconductor was observed and at high frequencies (
Abstract: In the present work, fly ash geopolymer based
composites including polyester (PES) waste were studied. Specimens
of three compositions were prepared: (a) fly ash geopolymer with 5%
PES waste; (b) fly ash geopolymer mortar with 5% PES waste; (c) fly
ash geopolymer mortar with 6.25% PES waste. Compressive and
bending strength measurements, water absorption test and
determination of thermal conductivity coefficient were performed.
The results showed that the addition of sand in a mixture of
geopolymer with 5% PES content led to higher compressive strength,
while it increased water absorption and reduced thermal conductivity
coefficient. The increase of PES addition in geopolymer mortars
resulted in a more dense structure, indicated by the increase of
strength and thermal conductivity and the decrease of water
absorption.
Abstract: Over the past four decades, the fatigue behavior of
nickel-based alloys has been widely studied. However, in recent
years, significant advances in the fabrication process leading to grain
size reduction have been made in order to improve fatigue properties
of aircraft turbine discs. Indeed, a change in particle size affects the
initiation mode of fatigue cracks as well as the fatigue life of the
material. The present study aims to investigate the fatigue behavior of
a newly developed nickel-based superalloy under biaxial-planar
loading. Low Cycle Fatigue (LCF) tests are performed at different
stress ratios so as to study the influence of the multiaxial stress state
on the fatigue life of the material. Full-field displacement and strain
measurements as well as crack initiation detection are obtained using
Digital Image Correlation (DIC) techniques. The aim of this
presentation is first to provide an in-depth description of both the
experimental set-up and protocol: the multiaxial testing machine, the
specific design of the cruciform specimen and performances of the
DIC code are introduced. Second, results for sixteen specimens
related to different load ratios are presented. Crack detection, strain
amplitude and number of cycles to crack initiation vs. triaxial stress
ratio for each loading case are given. Third, from fractographic
investigations by scanning electron microscopy it is found that the
mechanism of fatigue crack initiation does not depend on the triaxial
stress ratio and that most fatigue cracks initiate from subsurface
carbides.
Abstract: The development of allometric models is crucial to
accurate forest biomass/carbon stock assessment. The aim of this
study was to develop a set of biomass prediction models that will
enable the determination of total tree aboveground biomass for
savannah woodland area in Niger State, Nigeria. Based on the data
collected through biometric measurements of 1816 trees and
destructive sampling of 36 trees, five species specific and one site
specific models were developed. The sample size was distributed
equally between the five most dominant species in the study site
(Vitellaria paradoxa, Irvingia gabonensis, Parkia biglobosa,
Anogeissus leiocarpus, Pterocarpus erinaceous). Firstly, the
equations were developed for five individual species. Secondly these
five species were mixed and were used to develop an allometric
equation of mixed species. Overall, there was a strong positive
relationship between total tree biomass and the stem diameter. The
coefficient of determination (R2 values) ranging from 0.93 to 0.99 P
< 0.001 were realised for the models; with considerable low standard
error of the estimates (SEE) which confirms that the total tree above
ground biomass has a significant relationship with the dbh. F-test
values for the biomass prediction models were also significant at p
Abstract: The mixed micellization of adiphenine hydrochloride (ADP) with 1-decyl-3-methylimidazolium chloride (C10mim.Cl), was investigated at different mole fractions and temperatures by surface tension measurements. The synergistic behavior (i.e., non-ideal behavior) for binary mixtures was explained by the deviation of critical micelle concentration (cmc) from ideal critical micelle concentration (cmc*), micellar mole fraction (Xim) from ideal micellar mole fraction (Xiideal), the values of interaction parameter (β) and activity coefficients (fi) (for both mixed micelles and mixed monolayer). The excess free energy (ΔGex) for the ADP- C10mim.Cl binary mixtures explain the stability of mixed micelles in comparison to micelles of pure ADP and C10mim.Cl. Interfacial parameters, i.e., Gibbs surface excess (Гmax), minimum head group area at air/ water
interface (Amin), and free energy of micellization (ΔG0m) were also evaluated for the systems.
Abstract: The elastic period has a primary role in the seismic
assessment of buildings. Reliable calculations and/or estimates of the
fundamental frequency of a building and its site are essential during
analysis and design process. Various code formulas based on
empirical data are generally used to estimate the fundamental
frequency of a structure. For existing structures, in addition to code
formulas and available analytical tools such as modal analyses,
various methods of testing including ambient and forced vibration
testing procedures may be used to determine dynamic characteristics.
In this study, the dynamic properties of the 32 buildings located in
the Madinah of Saudi Arabia were identified using ambient motions
recorded at several, spatially-distributed locations within each
building. Ambient vibration measurements of buildings have been
analyzed and the fundamental longitudinal and transverse periods for
all tested buildings are presented. The fundamental mode of vibration
has been compared in plots with codes formulae (Saudi Building
Code, EC8, and UBC1997). The results indicate that measured
periods of existing buildings are shorter than that given by most
empirical code formulas. Recommendations are given based on the
common design and construction practice in Madinah city.
Abstract: Mechanical stress has a strong effect on the magnitude
of the Barkhausen-noise in structural steels. Because the
measurements are performed at the surface of the material, for a
sample sheet, the full effect can be described by a biaxial stress field.
The measured Barkhausen-noise is dependent on the orientation of
the exciting magnetic field relative to the axis of the stress tensor.
The sample inhomogenities including the residual stress also
modifies the angular dependence of the measured Barkhausen-noise.
We have developed a laboratory device with a cross like specimen
for bi-axial bending. The measuring head allowed performing
excitations in two orthogonal directions. We could excite the two
directions independently or simultaneously with different amplitudes.
The simultaneous excitation of the two coils could be performed in
phase or with a 90 degree phase shift. In principle this allows to
measure the Barkhausen-noise at an arbitrary direction without
moving the head, or to measure the Barkhausen-noise induced by a
rotating magnetic field if a linear superposition of the two fields can
be assumed.
Abstract: In recent years, the hair building fiber has become
popular, in other words, it is an effective method which helps people
who suffer hair loss or sparse hair since the hair building fiber is
capable to create a natural look of simulated hair rapidly. In the
markets, there are a lot of hair fiber brands that have been designed to
formulate an intense bond with hair strands and make the hair appear
more voluminous instantly. However, those products have their own
set of properties. Thus, in this report, some measurement techniques
are proposed to identify those products. Up to five different brands of
hair fiber are tested. The electrostatic and dielectric properties of the
hair fibers are macroscopically tested using design DC and high
frequency microwave techniques. Besides, the hair fibers are
microscopically analysis by magnifying the structures of the fiber
using scanning electron microscope (SEM). From the SEM photos,
the comparison of the uniformly shaped and broken rate of the hair
fibers in the different bulk samples can be observed respectively.
Abstract: The wear measuring and wear modelling are
fundamental issues in the industrial field, mainly correlated to the
economy and safety. Therefore, there is a need to study the wear
measurements and wear estimation. Pin-on-disc test is the most
common test which is used to study the wear behaviour. In this paper,
the pin-on-disc (AEROTECH UNIDEX 11) is used for the
investigation of the effects of normal load and hardness of material on
the wear under dry and sliding conditions. In the pin-on-disc rig, two
specimens were used; one, a pin is made of steel with a tip, positioned
perpendicular to the disc, where the disc is made of aluminium. The
pin wear and disc wear were measured by using the following
instruments: The Talysurf instrument, a digital microscope, and the
alicona instrument. The Talysurf profilometer was used to measure
the pin/disc wear scar depth, digital microscope was used to measure
the diameter and width of wear scar, and the alicona was used to
measure the pin wear and disc wear. After that, the Archard model,
American Society for Testing and Materials model (ASTM), and
neural network model were used for pin/disc wear modelling.
Simulation results were implemented by using the Matlab program.
This paper focuses on how the alicona can be used for wear
measurements and how the neural network can be used for wear
estimation.
Abstract: This article is trying to determine the status of flue gas
that is entering the KWH heat exchanger from combustion chamber
in order to calculate the heat transfer ratio of the heat exchanger.
Combination of measurement, calculation and computer simulation
was used to create a useful way to approximate the heat transfer rate.
The measurements were taken by a number of sensors that are
mounted on the experimental device and by a thermal imaging
camera. The results of the numerical calculation are in a good
correspondence with the real power output of the experimental
device. That result shows that the research has a good direction and
can be used to propose changes in the construction of the heat
exchanger, but still needs enhancements.