Abstract: In this research article a comprehensive investigation
has been carried out to determine the effect of thermal cycle on
temperature dependent process parameters developed during gas
tungsten arc (GTA) welding of high carbon (AISI 1090) steel butt
joints. An experiment based thermal analysis has been performed to
obtain the thermal history. We have focused on different
thermophysical properties such as thermal conductivity, heat transfer
coefficient and cooling rate. Angular torch model has been utilized to
find out the surface heat flux and its variation along the fusion zone as
well as along the longitudinal direction from fusion boundary. After
welding and formation of weld pool, heat transfer coefficient varies
rapidly in the vicinity of molten weld bead and heat affected zone. To
evaluate the heat transfer coefficient near the fusion line and near the
rear end of the plate (low temperature region), established correlation
has been implemented and has been compared with empirical
correlation which is noted as coupled convective and radiation heat
transfer coefficient. Change in thermal conductivity has been
visualized by analytical model of moving point heat source. Rate of
cooling has been estimated by using 2-dimensional mathematical
expression of cooling rate and it has shown good agreement with
experimental temperature cycle. Thermophysical properties have been
varied randomly within 0 -10s time span.
Abstract: The exposure to outdoor air pollution causes lung
cancer and increases the risk of bladder cancer. Because air pollution
in urban areas is mainly caused by transportation, it is necessary to
evaluate pollutant exhaust emissions from vehicles during their realworld
use. Nevertheless their evaluation and reduction is a key
problem, especially in the cities, that account for more than 50% of
world population.
A particular attention was given to the slope variability along the
streets during each journey performed by the instrumented vehicle.
In this paper we dealt with the problem of describing a
quantitatively approach for the reconstruction of GPS coordinates and
altitude, in the context of correlation study between driving cycles /
emission / geographical location, during an experimental campaign
realized with some instrumented cars.
Finally the slope analysis can be correlated to the emission and
consumption values in a specific road position, and it could be
evaluated its influence on their behaviour.
Abstract: Quality control helps industries in improvements of its
product quality and productivity. Statistical Process Control (SPC) is
one of the tools to control the quality of products that turning practice
in bringing a department of industrial engineering process under
control. In this research, the process control of a turning
manufactured at workshops machines. The varying measurements
have been recorded for a number of samples of a rice polished
cylinder obtained from a number of trials with the turning practice.
SPC technique has been adopted by the process is finally brought
under control and process capability is improved.
Abstract: Due to growing concern about environmental and
social consequences throughout the world, a need has been felt to
incorporate sustainability concepts in conventional manufacturing.
This paper is an attempt to identify and evaluate drivers in
implementing sustainable manufacturing in Indian context. Nine
possible drivers for successful implementation of sustainable
manufacturing have been identified from extensive review. Further,
Decision Making Trial and Evaluation Laboratory (DEMATEL)
approach has been utilized to evaluate and categorize these identified
drivers for implementing sustainable manufacturing in to the cause
and effect groups. Five drivers (Societal Pressure and Public
Concerns; Regulations and Government Policies; Top Management
Involvement, Commitment and Support; Effective Strategies and
Activities towards Socially Responsible Manufacturing and Market
Trends) have been categorized into the cause group and four drivers
(Holistic View in Manufacturing Systems; Supplier Participation;
Building Sustainable culture in Organization; and Corporate Image
and Benefits) have been categorized into the effect group. “Societal
Pressure and Public Concerns” has been found the most critical driver
and “Corporate Image and Benefits” as least critical or the most
easily influenced driver to implementing sustainable manufacturing
in Indian context. This paper may surely help practitioners in better
understanding of these drivers and their priorities towards effective
implementation of sustainable manufacturing.
Abstract: The present study involved analysis of certain
characteristics of the perennial ryegrass (Lolium perenne L.)
genotypes collected from the natural flora of Ankara, and explores a
correlation among them. In order to evaluate the plants for breeding
purpose as per Turkey's environmental conditions, the perennial
ryegrass plants were collected from natural pasture of Ankara in 2004
and were utilized for the study. Seeds of the collected plants were
sown in pots and seedlings were prepared in a greenhouse. In 2005,
the seedlings were transplanted at 50 × 50 cm2 intervals in
Randomized Complete Blocks Design in an experimental field. In
2007 and 2008, data were recorded from the observations and
measurements of 568 perennial ryegrasses. The plant characteristics,
which were investigated, included re-growth time in spring, color,
density, growth habit, tendency to form inflorescence, time of
inflorescence, plant height, length of upper internode, spike length,
leaf length, leaf width, leaf area, leaf shape, number of spikelets per
spike, seed yield per spike and 1000 grain weight and the correlation
analyses were made using this data. Correlation coefficients were
estimated between all paired combinations of the studied traits. The
yield components exhibited varying trends of association among
themselves. Seed yield per spike showed significant and positive
association with the number of spikelets per spike, 1000 grain weight,
plant height, length of upper internode, spike length, leaf length, leaf
width, leaf area and color, but significant and negative association
with the growth habit and re-growth time in spring.
Abstract: India holds 17.5% of the world’s population but has
only 2% of the total geographical area of the world where 27.35% of
the area is categorized as wasteland due to lack of or less
groundwater. So there is a demand for excessive groundwater for
agricultural and non agricultural activities to balance its growth rate.
With this in mind, an attempt is made to find the groundwater
potential zone in Gomukhi Nadhi sub basin of Vellar River basin,
TamilNadu, India covering an area of 1146.6 Sq.Km consists of 9
blocks from Peddanaickanpalayam to Virudhachalam in the sub
basin. The thematic maps such as Geology, Geomorphology,
Lineament, Landuse and Landcover and Drainage are prepared for
the study area using IRS P6 data. The collateral data includes rainfall,
water level, soil map are collected for analysis and inference. The
digital elevation model (DEM) is generated using Shuttle Radar
Topographic Mission (SRTM) and the slope of the study area is
obtained. ArcGIS 10.1 acts as a powerful spatial analysis tool to find
out the ground water potential zones in the study area by means of
weighted overlay analysis. Each individual parameter of the thematic
maps are ranked and weighted in accordance with their influence to
increase the water level in the ground. The potential zones in the
study area are classified viz., Very Good, Good, Moderate, Poor with
its aerial extent of 15.67, 381.06, 575.38, 174.49 Sq.Km respectively.
Abstract: Energy consumption and users’ satisfaction were
compared in three LEED certified office buildings in turkey and an
office building in Egypt. The field studies were conducted in summer
2012. The measured environmental parameters in the four buildings
were indoor air temperature, relative humidity, CO2 percentage and
light intensity. The traditional building is located in Smart Village in
Abu Rawash, Cairo, Egypt. The building was studied for 7 days
resulting in 84 responds. The three rated buildings are in Istanbul;
Turkey. A Platinum LEED certified office building is owned by
BASF and gained a platinum certificate for new construction and
major renovation. The building was studied for 3 days resulting in 13
responds. A Gold LEED certified office building is owned by BASF
and gained a gold certificate for new construction and major
renovation. The building was studied for 2 days resulting in 10
responds. A silver LEED certified office building is owned by
Unilever and gained a silver certificate for commercial interiors. The
building was studied for 7 days resulting in 84 responds.
The results showed that all buildings had no significant difference
regarding occupants’ satisfaction with the amount of lighting, noise
level, odor and access to the outdoor view. There was significant
difference between occupants’ satisfaction in LEED certified
buildings and the traditional building regarding the thermal
environment and the perception of the general environment (colors,
carpet and decoration. The findings suggest that careful design could
lead to a certified building that enhances the thermal environment and
the perception of the indoor environment leading to energy
consumption without scarifying occupants’ satisfaction.
Abstract: The biosynthesis of nanoparticles by microorganisms,
on the contrary to chemical synthesis, is an environmentally-friendly
process which has low energy requirements. In this investigation, we
used the microorganism Geobacillus wiegelii, strain GWE1, an
aerobic thermophile belonging to genus Geobacillus, isolated from a
drying oven. This microorganism has the ability to reduce selenite
evidenced by the change of color from colorless to red in the culture.
Elemental analysis and composition of the particles were verified
using transmission electron microscopy and energy-dispersive X-ray
analysis. The nanoparticles have a defined spherical shape and a
selenium elemental state. Previous experiments showed that the
presence of the whole microorganism for the reduction of selenite
was not necessary. The results strongly suggested that an intracellular
NADPH/NADH-dependent reductase mediates selenium
nanoparticles synthesis under aerobic conditions. The enzyme was
purified and identified by mass spectroscopy MALDI-TOF TOF
technique. The enzyme is a 1-pyrroline-5-carboxylate dehydrogenase.
Histograms of nanoparticles sizes were obtained. Size distribution
ranged from 40-160 nm, where 70% of nanoparticles have less than
100 nm in size. Spectroscopic analysis showed that the nanoparticles
are composed of elemental selenium. To analyse the effect of pH in
size and morphology of nanoparticles, the synthesis of them was
carried out at different pHs (4.0, 5.0, 6.0, 7.0, 8.0). For
thermostability studies samples were incubated at different
temperatures (60, 80 and 100 ºC) for 1 h and 3 h. The size of all
nanoparticles was less than 100 nm at pH 4.0; over 50% of
nanoparticles have less than 100 nm at pH 5.0; at pH 6.0 and 8.0 over
90% of nanoparticles have less than 100 nm in size. At neutral pH
(7.0) nanoparticles reach a size around 120 nm and only 20% of them
were less than 100 nm. When looking at temperature effect,
nanoparticles did not show a significant difference in size when they
were incubated between 0 and 3 h at 60 ºC. Meanwhile at 80 °C the
nanoparticles suspension lost its homogeneity. A change in size was
observed from 0 h of incubation at 80ºC, observing a size range
between 40-160 nm, with 20% of them over 100 nm. Meanwhile
after 3 h of incubation at size range changed to 60-180 nm with 50%
of them over 100 nm. At 100 °C the nanoparticles aggregate forming
nanorod structures. In conclusion, these results indicate that is
possible to modulate size and shape of biologically synthesized
nanoparticles by modulating pH and temperature.
Abstract: The purpose of this study was to investigate
perceptions of climate change risk to forest ecosystems and forestbased
communities as well as perceived effectiveness of adaptation
strategies for climate change as well as challenges for adaptation.
Data was gathered using a pre-tested semi-structured questionnaire.
Simple random selection technique was applied. For the majority of
issues, the responses were obtained on multi-point likert scales, and
the scores provided were, in turn, used to estimate the means and
other useful estimates. A composite knowledge index developed
using correct responses to a set of self-rated statements were used to
evaluate the issues. The mean of the knowledge index was 0.64. Also
all respondents recorded values of the knowledge index above 0.25.
Increase forest fire was perceived by respondents as the greatest risk
to forest eco-system. Decrease access to water supplies was perceived
as the greatest risk to livelihoods of forest based communities. The
most effective adaptation strategy relevant to climate change risks to
forest eco-systems and forest based communities livelihoods in
Kathmandu valley in Nepal as perceived by the respondents was
reforestation and afforestation. As well, lack of public awareness was
perceived as the major limitation for climate change adaptation.
However, perceived risks as well as effective adaptation strategies
showed an inconsistent association with knowledge indicators and
social-cultural variables. The results provide useful information to
any party who involve with climate change issues in Nepal, since
such attempts would be more effective once the people’s perceptions
on these aspects are taken into account.
Abstract: The presence of endocrine-disrupting compounds,
such as bisphenol A (BPA), in the environment can cause serious
health problems. However, there are controversial opinions. This
study investigated the reproductive, metabolic, oxidative and
immunologic-disrupting effects of bisphenol A in male rabbits.
Rabbits were divided into five groups. The first four rabbit groups
were administered oral BPA (1, 10, 50, or 100 mg/kg/day) for ten
weeks. The fifth group was administered corn oil as the vehicle. BPA
significantly decreased serum testosterone, estradiol and the free
androgen index (FAI) and significantly increased sex hormone
binding globulin (SHBG) compared with the placebo group. The
higher doses of BPA showed a significant decrease in follicular
stimulating hormone (FSH) and luteinizing hormone (LH). A
significant increase in blood glucose levels was identified in the BPA
groups. The non-significant difference in insulin levels is a novel
finding. The cumulative testicular toxicity of BPA was clearly
demonstrated by the dose-dependent decrease in absolute testes
weight, primary measures of semen quality and a significant increase
in testicular malonaldehyde (MDA). Moreover, BPA significantly
decreased total antioxidant capacity (TAC) and significantly
increased immunoglobulin G (IgG) at the highest concentration. Our
results suggest that BPA, especially at higher doses, is associated
with many adverse effects on metabolism, oxidative stress, immunity,
sperm quality and markers of androgenic action.
Abstract: In this paper it was examined the influence of margin
regulation on stock market volatility in EU 1993 – 2014. Regulating
margin requirements or haircuts for securities financing transactions
has for a long time been considered as a potential tool to limit the
build-up of leverage and dampen volatility in financial markets. The
margin requirement dictates how much investors can borrow against
these securities. Margin can be an important part of investment.
Using daily and monthly stock returns and there is no convincing
evidence that EU Regulation margin requirements have served to
dampen stock market volatility. In this paper was detected the
expected negative relation between margin requirements and the
amount of margin credit outstanding. Also, it confirmed that changes
in margin requirements by the EU regulation have tended to follow
than lead changes in market volatility. For the analysis have been
used the modified Levene statistics to test whether the standard
deviation of stock returns in the 25, 50 and 100 days preceding
margin changes is the same as that in the succeeding 25, 50 and 100
days. The analysis started in May 1993 when it was first empowered
to set the initial margin requirement and the last sample was in May
2014. To test whether margin requirements influence stock market
volatility over the long term, the sample of stock returns was divided
into 14 periods, according to the 14 changes in margin requirements.
Abstract: Objective of this study is to explore the recent trends,
patterns and the structural changes in the labour migration from Sri
Lanka to Middle East countries and to discuss the possible impacts of
those changes on the remittance flow. Study uses secondary data
published by Sri Lanka Bureau of Foreign Employment and Central
Bank. Thematic analysis of the secondary data revealed that the
migration for labour has increased rapidly during past decades.
Parallel with that the gender and the skill composition of the
migration flow has been changing. Similarly, the destinations for
male migration have changed over the period. These show positive
implications on the international remittance receipts to the country.
Abstract: Magnetic powder of Sr-ferrite was prepared by
conventional and sol-gel auto-combustion methods. In conventional
method, strontium carbonate and ferric oxide powders were mixed
together and then mixture was calcined. In sol-gel auto-combustion
method, a solution containing strontium nitrate, ferric nitrate and
citric acid was heated until the combustion took place automatically;
then, as-burnt powder was calcined. Thermal behavior, phase
identification, morphology and magnetic properties of powders
obtained by these two methods were compared by DTA, XRD, SEM
and VSM techniques. According to the results of DTA analysis,
formation temperature of Sr-ferrite obtained by conventional and solgel
auto-combustion methods were 1300°C and 1000°C, respectively.
XRD results confirmed the formation of pure Sr-ferrite at the
mentioned temperatures. Plate and hexagonal-shape particles of Srferrite
were observed using SEM. The Sr-ferrite powder obtained by
sol-gel auto-combustion method had saturation magnetization of
66.03 emu/g and coercivity of 5731 Oe in comparison with values of
58.20 emu/g and 4378 Oe obtained by conventional method.
Abstract: In an urban area the location allocation of emergency
services mobile units, such as ambulances, police patrol cars must be
designed so as to achieve a prompt response to demand locations.
In this paper the partition of a given urban network into distinct
sub-networks is performed such that the vertices in each component
are close and simultaneously the sums of the corresponding
population in the sub-networks are almost uniform. The objective
here is to position appropriately in each sub-network a mobile
emergency unit in order to reduce the response time to the demands.
A mathematical model in framework of graph theory is developed.
In order to clarify the corresponding method a relevant numerical
example is presented on a small network.
Abstract: Heightened concerns over the amount of carbon
emitted from coal-related processes are generating shifts to the
application of biomass. In co-gasification, where coal is gasified
along with biomass, the biomass may be fed together with coal (cofeeding)
or an independent biomass gasifier needs to be integrated
with the coal gasifier. The main aim of this work is to evaluate the
biomass introduction methods in coal co-gasification. This includes
the evaluation of biomass concentration input (B0 to B100) and its
gasification performance. A process model is developed and
simulated in Aspen HYSYS, where both coal and biomass are
modelled according to its ultimate analysis. It was found that the
syngas produced increased with increasing biomass content for both
co-feeding and independent schemes. However, the heating values
and heat duties decreases with biomass concentration as more CO2
are produced from complete combustion.
Abstract: Climate warming would increase rainfall by shifting
precipitation falling form from snow to rain, and would accelerate
snow cover disappearing by increasing snowpack. Using temperature
and precipitation data in the temperature-index snowmelt model, we
evaluated variability of snowfall and continuous snow cover duration
(CSCD) during 1944-2010 over Pelso, central Finland. Mann-
Kendall non-parametric test determined that annual precipitation
increased by 2.69 (mm/year, p
Abstract: Columns have traditionally been constructed of
reinforced concrete or structural steel. Much attention was allocated
to estimate the axial capacity of the traditional column sections to the
detriment of other forms of construction. Other forms of column
construction such as Concrete Filled Double Skin Tubes received
little research attention, and almost no attention when subjected to
eccentric loading. This paper investigates the axial capacity of
columns when subjected to eccentric loading. The experimental axial
capacities are compared to other established theoretical formulae on
concentric loading to determine a possible relationship. The study
found a good correlation between the reduction in axial capacity for
different column lengths and hollow section ratios.
Abstract: Electricity is recognized as fundamental to
industrialization and improving the quality of life of the people.
Harnessing the immense untapped hydropower potential in Tripura
region opens avenues for growth and provides an opportunity to
improve the well-being of the people of the region, while making
substantial contribution to the national economy. Gumti hydro power
plant generates power to mitigate the crisis of power in Tripura,
India. The first unit of hydro power plant (5MW) was commissioned
in June 1976 & another two units of 5 MW was commissioned
simultaneously. But out of 15MW capacity at present only 8MW-
9MW power is produced from Gumti hydro power plant during rainy
season. But during lean season the production reduces to 0.5MW due
to shortage of water. Now, it is essential to implement some
mitigation measures so that the further atrocities can be prevented
and originality will be possible to restore. The decision making
ability of the Analytic Hierarchy Process (AHP) and Concordance
Analysis Techniques (CAT) are utilized to identify the better decision
or solution to the present problem. Some related attributes are
identified by the method of surveying within the experts and the
available reports and literatures. Similar criteria are removed and
ultimately seven relevant ones are identified. All the attributes are
compared with each other and rated accordingly to their importance
over the other with the help of Pair wise Comparison Matrix. In the
present investigation different mitigation measures are identified and
compared to find the best suitable alternative which can solve the
present uncertainties involving the existence of the Gumti Hydro
Power Plant.
Abstract: Paper presents a study about dynamic effects obtained
from the dynamic load testing of the city highway bridges in Latvia
carried out from 2005 to 2012. 9 prestressed concrete bridges and 4
composite bridges were considered. 11 of 13 bridges were designed
according to the Eurocodes but two according to the previous
structural codes used in Latvia (SNIP 2.05.03-84). The dynamic
properties of the bridges were obtained by heavy vehicle passing the
bridge roadway with different driving speeds and with or without
even pavement. The obtained values of the Dynamic amplification
factor (DAF) and the bridge natural frequency were analyzed and
compared to the values of built-in traffic load models provided in
Eurocode 1. The actual DAF values for even bridge pavement in the
most cases are smaller than the value adopted in Eurocode 1. Vehicle
speed for uneven pavements significantly influence Dynamic
amplification factor values.
Abstract: The thermo-mechanical behaviour of concrete energy
pile foundations with different single and double U-tube shapes
incorporated was analysed using the Comsol Multi-physics package.
For the analysis, a 3D numerical model in real scale of the concrete
pile and surrounding soil was simulated regarding actual operation of
ground heat exchangers (GHE) and the surrounding ambient
temperature. Based on initial ground temperature profile measured in
situ, tube inlet temperature was considered to range from 6oC to 0oC
(during the contraction process) over a 30-day period. Extra thermal
stresses and deformations were calculated during the simulations and
differences arising from the use of two different systems (single-tube
and double-tube) were analysed. The results revealed no significant
difference for extra thermal stresses at the centre of the pile in either
system. However, displacements over the pile length were found to
be up to 1.5-fold higher in the double-tube system than the singletube
system.