Abstract: An immunomodulator bioproduct is prepared in a
batch bioprocess with a modified bacterium Pseudomonas
aeruginosa. The bioprocess is performed in 100 L Bioengineering
bioreactor with 42 L cultivation medium made of peptone, meat
extract and sodium chloride. The optimal bioprocess parameters were
determined: temperature – 37 0C, agitation speed - 300 rpm, aeration
rate – 40 L/min, pressure – 0.5 bar, Dow Corning Antifoam M-max.
4 % of the medium volume, duration - 6 hours. This kind of
bioprocesses are appreciated as difficult to control because their
dynamic behavior is highly nonlinear and time varying. The aim of
the paper is to present (by comparison) different models based on
experimental data.
The analysis criteria were modeling error and convergence rate.
The estimated values and the modeling analysis were done by using
the Table Curve 2D.
The preliminary conclusions indicate Andrews-s model with a
maximum specific growth rate of the bacterium in the range of
0.8 h-1.
Abstract: Batch fermentation of 5, 10 and 25 g/L biodiesel
derived crude glycerol was carried out at 30, 37 and 450C by
Clostridium pasteurianum cells immobilized on silica. Maximum
yield of 1,3-propanediol (PDO) (0.60 mol/mol), and ethanol (0.26
mol/mol) were obtained from 10 g/L crude glycerol at 30 and 370C
respectively. Maximum yield of butanol (0.28 mol/mol substrate
added) was obtained at 370C with 25 g/L substrate. None of the three
products were detected at 45oC even after 10 days of fermentation.
Only traces of ethanol (0.01 mol/mol) were detected at 450C with 5
g/L substrate. The results obtained for 25 g/L substrate utilization
were fitted in first order rate equation to obtain the values of rate
constant at three different temperatures for bioconversion of glycerol.
First order rate constants for bioconversion of glycerol at 30, 37 and
45oC were found to be 0.198, 0.294 and 0.029/day respectively.
Activation energy (Ea) for crude glycerol bioconversion was
calculated to be 57.62 kcal/mol.
Abstract: A supervisory scheme is proposed that implements Stepwise Safe Switching Logic. The functionality of the supervisory scheme is organized in the following eight functional units: Step- Wise Safe Switching unit, Common controllers design unit, Experimentation unit, Simulation unit, Identification unit, Trajectory cruise unit, Operating points unit and Expert system unit. The supervisory scheme orchestrates both the off-line preparative actions, as well as the on-line actions that implement the Stepwise Safe Switching Logic. The proposed scheme is a generic tool, that may be easily applied for a variety of industrial control processes and may be implemented as an automation software system, with the use of a high level programming environment, like Matlab.
Abstract: In this paper we propose the study of a centrifugal pump control system driven by a three-phase induction motor, which is supplied by a PhotoVoltaic PV generator. The system includes solar panel, a DC / DC converter equipped with its MPPT control, a voltage inverter to three-phase Pulse Width Modulation - PWM and a centrifugal pump driven by a three phase induction motor. In order to control the flow of the centrifugal pump, a Direct Torque Control - DTC of the induction machine is used. To illustrate the performances of the control, simulation results are carried out using Matlab/Simulink.
Abstract: Latvia is the fourth in the world by means of broadband internet speed. The total number of internet users in Latvia exceeds 70% of its population. The number of active mailboxes of the local internet e-mail service Inbox.lv accounts for 68% of the population and 97.6% of the total number of internet users. The Latvian portal Draugiem.lv is a phenomenon of social media, because 58.4 % of the population and 83.5% of internet users use it. A majority of Latvian company profiles are available on social networks, the most popular being Twitter.com. These and other parameters prove the fact consumers and companies are actively using the Internet.
However, after the authors in a number of studies analyzed how enterprises are employing the e-environment, namely, e-environment tools, they arrived to the conclusions that are not as flattering as the aforementioned statistics. There is an obvious contradiction between the statistical data and the actual studies. As a result, the authors have posed a question: Why are entrepreneurs resistant to e-tools? In order to answer this question, the authors have addressed the Technology Acceptance Model (TAM). The authors analyzed each phase and determined several factors affecting the use of e-environment, reaching the main conclusion that entrepreneurs do not have a sufficient level of e-literacy (digital literacy).
The authors employ well-established quantitative and qualitative methods of research: grouping, analysis, statistic method, factor analysis in SPSS 20 environment etc.
The theoretical and methodological background of the research is formed by, scientific researches and publications, that from the mass media and professional literature, statistical information from legal institutions as well as information collected by the author during the survey.
Abstract: In this paper, a novel contrast enhancement technique
for contrast enhancement of a low-contrast satellite image has been
proposed based on the singular value decomposition (SVD) and
discrete cosine transform (DCT). The singular value matrix
represents the intensity information of the given image and any
change on the singular values change the intensity of the input image.
The proposed technique converts the image into the SVD-DCT
domain and after normalizing the singular value matrix; the enhanced
image is reconstructed by using inverse DCT. The visual and
quantitative results suggest that the proposed SVD-DCT method
clearly shows the increased efficiency and flexibility of the proposed
method over the exiting methods such as Linear Contrast Stretching
technique, GHE technique, DWT-SVD technique, DWT technique,
Decorrelation Stretching technique, Gamma Correction method
based techniques.
Abstract: Partitioning is a critical area of VLSI CAD. In order to build complex digital logic circuits its often essential to sub-divide multi -million transistor design into manageable Pieces. This paper looks at the various partitioning techniques aspects of VLSI CAD, targeted at various applications. We proposed an evolutionary time-series model and a statistical glitch prediction system using a neural network with selection of global feature by making use of clustering method model, for partitioning a circuit. For evolutionary time-series model, we made use of genetic, memetic & neuro-memetic techniques. Our work focused in use of clustering methods - K-means & EM methodology. A comparative study is provided for all techniques to solve the problem of circuit partitioning pertaining to VLSI design. The performance of all approaches is compared using benchmark data provided by MCNC standard cell placement benchmark net lists. Analysis of the investigational results proved that the Neuro-memetic model achieves greater performance then other model in recognizing sub-circuits with minimum amount of interconnections between them.
Abstract: This paper reports work done to improve the modeling of complex processes when only small experimental data sets are available. Neural networks are used to capture the nonlinear underlying phenomena contained in the data set and to partly eliminate the burden of having to specify completely the structure of the model. Two different types of neural networks were used for the application of Pulping of Sugar Maple problem. A three layer feed forward neural networks, using the Preconditioned Conjugate Gradient (PCG) methods were used in this investigation. Preconditioning is a method to improve convergence by lowering the condition number and increasing the eigenvalues clustering. The idea is to solve the modified problem where M is a positive-definite preconditioner that is closely related to A. We mainly focused on Preconditioned Conjugate Gradient- based training methods which originated from optimization theory, namely Preconditioned Conjugate Gradient with Fletcher-Reeves Update (PCGF), Preconditioned Conjugate Gradient with Polak-Ribiere Update (PCGP) and Preconditioned Conjugate Gradient with Powell-Beale Restarts (PCGB). The behavior of the PCG methods in the simulations proved to be robust against phenomenon such as oscillations due to large step size.
Abstract: Product customization is an essential requirement for
manufacturing firms to achieve higher customers- satisfaction and
fulfill business target. In order to achieve these objectives, firms need
to handle both external varieties such as customer preference,
government regulations, cultural considerations etc and internal
varieties such as functional requirements of product, production
efficiency, quality etc. Both of the varieties need to be accumulated
and integrated together for the purpose of producing customized
product. These varieties are presented and discussed in this paper
along with the perspectives of modular product design and
development process. Other development strategies such as
modularity, component commonality, product family design and
product platform are presented with a view to achieve product variety
quickly and economically. A case example both for the concept of
modular design and platform based product development process is
also presented with the help of design structure matrix (DSM) tool.
This paper is concluded with several managerial implications and
future research direction.
Abstract: An Automated Rapid Maxillary Expander (ARME) is
a specially designed microcontroller-based orthodontic appliance to
overcome the shortcomings imposed by the traditional maxillary
expansion appliances. This new device is operates by automatically
widening the maxilla (upper jaw) by expanding the midpalatal suture
[1]. The ARME appliance that has been developed is a combination
of modified butterfly expander appliance, micro gear, micro motor,
and microcontroller to automatically produce light and continuous
pressure to expand the maxilla. For this study, the functionality of the
system is verified through laboratory tests by measure the forced
applied to the teeth each time the maxilla expands. The laboratory
test results show that the developed appliance meets the desired
performance specifications consistently.
Abstract: A novel nanofinishing process using improved ball
end magnetorheological (MR) finishing tool was developed for finishing of flat as well as 3D surfaces of ferromagnetic and non ferromagnetic workpieces. In this process a magnetically controlled
ball end of smart MR polishing fluid is generated at the tip surface of
the tool which is used as a finishing medium and it is guided to
follow the surface to be finished through computer controlled 3-axes
motion controller. The experiments were performed on ferromagnetic
workpiece surface in the developed MR finishing setup to study the effect of finishing time on final surface roughness. The performance
of present finishing process on final finished surface roughness was studied. The surface morphology was observed under scanning
electron microscopy and atomic force microscope. The final surface finish was obtained as low as 19.7 nm from the initial surface
roughness of 142.9 nm. The outcome of newly developed finishing process can be found useful in its applications in aerospace,
automotive, dies and molds manufacturing industries, semiconductor and optics machining etc.
Abstract: Green house effect has becomes a serious concern in
many countries due to the increase consumption of the fossil fuel.
There have been many studies to find an alternative power source.
Wind energy found to be one of the most useful solutions to help in
overcoming the air pollution and global. There is no agreed solution
to conversion of wind energy to electrical energy. In this paper, the
advantages of using a Switched Reluctance Generator (SRG) for
wind energy applications. The theoretical study of the self excitation
of a SRG and the determination of the variable parameters in a SRG
design are discussed. The design parameters for the maximum power
output of the SRG are computed using Matlab simulation. The
designs of the circuit to control the variable parameters in a SRG to
provide the maximum power output are also discussed.
Abstract: The charge-pump circuit is an important component in a phase-locked loop (PLL). The charge-pump converts Up and Down signals from the phase/frequency detector (PFD) into current. A conventional CMOS charge-pump circuit consists of two switched current sources that pump charge into or out of the loop filter according to two logical inputs. The mismatch between the charging current and the discharging current causes phase offset and reference spurs in a PLL. We propose a new charge-pump circuit to reduce the current mismatch by using a regulated cascode circuit. The proposed charge-pump circuit is designed and simulated by spectre with TSMC 0.18-μm 1.8-V CMOS technology.
Abstract: This paper discusses the applicability of the Data
Distribution Service (DDS) for the development of automated and modular manufacturing systems which require a flexible and robust
communication infrastructure. DDS is an emergent standard for datacentric publish/subscribe middleware systems that provides an
infrastructure for platform-independent many-to-many
communication. It particularly addresses the needs of real-time systems that require deterministic data transfer, have low memory
footprints and high robustness requirements. After an overview of the
standard, several aspects of DDS are related to current challenges for the development of modern manufacturing systems with distributed architectures. Finally, an example application is presented based on a modular active fixturing system to illustrate the described aspects.
Abstract: This paper demonstrates design and construction of
microcontroller-based telephone exchange system and the aims of
this paper is to study telecommunication, connection with
PIC16F877A and DTMF MT8870D. In microcontroller system, PIC
16F877 microcontroller is used to control the call processing. Dial
tone, busy tone and ring tone are provided during call progress.
Instead of using ready made tone generator IC, oscillator based tone
generator is used. The results of this telephone exchange system are
perfect for homes and small businesses needing the extensions. It
requires the phone operation control system, the analog interface
circuit and the switching circuit. This exchange design will contain
eight channels.
It is the best low cost, good quality telephone exchange for today-s
telecommunication needs. It offers the features available in much
more expensive PBX units without using high-priced phones. It is for
long distance telephone services.
Abstract: Metaphor has recently gained extensive interest most probably due to developments in cognitive sciences and the study of language as the reflection of humans- world perception. Metaphor is no longer reckoned as solely literary expressive means. Nowadays it is studied in a whole number of discourses, such as politics, law, medicine, sports, etc. with the purpose of the analysis and determining its role. The scientific language is not an exception. It might seem that metaphor cannot suit it; we would dare to draw a hypothesis that metaphor has indeed found its stable place in terminology. In comprehension of metaphorically represented terms the stage of visualization plays a significant role. We proceeded on the assumption that this stage is the main in provision of better term comprehension and would try to exemplify it with metaphoricallyoriented terms.
Abstract: This paper focuses on the problem of a common linear copositive Lyapunov function(CLCLF) existence for discrete-time switched positive linear systems(SPLSs) with bounded time-varying delays. In particular, applying system matrices, a special class of matrices are constructed in an appropriate manner. Our results reveal that the existence of a common copositive Lyapunov function can be related to the Schur stability of such matrices. A simple example is provided to illustrate the implication of our results.
Abstract: The purpose of this study is to identify the critical success factors (CSFs) for the effective implementation of Six Sigma in non-formal service Sectors.
Based on the survey of literature, the critical success factors (CSFs) for Six Sigma have been identified and are assessed for their importance in Non-formal service sector using Delphi Technique. These selected CSFs were put forth to the panel of expert to cluster them and prepare cognitive map to establish their relationship.
All the critical success factors examined and obtained from the review of literature have been assessed for their importance with respect to their contribution to Six Sigma effectiveness in non formal service sector.
The study is limited to the non-formal service sectors involved in the organization of religious festival only. However, the similar exercise can be conducted for broader sample of other non-formal service sectors like temple/ashram management, religious tours management etc.
The research suggests an approach to identify CSFs of Six Sigma for Non-formal service sector. All the CSFs of the formal service sector will not be applicable to Non-formal services, hence opinion of experts was sought to add or delete the CSFs. In the first round of Delphi, the panel of experts has suggested, two new CSFs-“competitive benchmarking (F19) and resident’s involvement (F28)”, which were added for assessment in the next round of Delphi. One of the CSFs-“fulltime six sigma personnel (F15)” has been omitted in proposed clusters of CSFs for non-formal organization, as it is practically impossible to deploy full time trained Six Sigma recruits.
Abstract: Static synchronous compensator (STATCOM) is a shunt connected voltage source converter (VSC), which can affect rapid control of reactive flow in the transmission line by controlling the generated a.c. voltage. The main aim of the paper is to design a power system installed with a Static synchronous compensator (STATCOM) and demonstrates the application of the linearised Phillips-heffron model in analyzing the damping effect of the STATCOM to improve power system oscillation stability. The proposed PI controller is designed to coordinate two control inputs: Voltage of the injection bus and capacitor voltage of the STATCOM, to improve the Dynamic stability of a SMIB system .The power oscillations damping (POD) control and power system stabilizer (PSS) and their coordinated action with proposed controllers are tested. The simulation result shows that the proposed damping controllers provide satisfactory performance in terms of improvements of dynamic stability of the system.
Abstract: In this study the regional stability of a rotor system which is supported on rolling bearings with radial clearance is studied. The rotor is assumed to be rigid. Due to radial clearance of bearings and dynamic configuration of system, each rolling elements of bearings has the possibility to be in contact with both of the races (under compression) or lose its contact. As a result, this change in dynamic of the system makes it to be known as switching system which is a type of Hybrid systems. In this investigation by adopting Multiple Lyapunov Function theorem and using Hamiltonian function as a candidate Lyapunov function, the stability of the system is studied. The purpose of this study is to inspect the regional stability of rotor-roller bearing and rotor-ball bearing systems.