Abstract: In production of medicinal plants, seed germination is
very important problem. The treated seeds (control, hydro priming
and ZnSO4) of Cumin (Cuminum cyminum L.) were evaluated at
germination and seedling growth for tolerance to salt (NaCl and
Na2SO4) conditions at the same water potentials of 0.0, -0.3, -0.6, -
0.9 and -1.2MPa. Electrical conductivity (EC) values of the NaCl
solutions were 0.0, 6.5, 12.7, 18.4 and 23.5 dSm-1, respectively. The
objective of the study was to determine factors responsible for
germination and early seedling growth due to salt toxicity or osmotic
effect and to optimize the best priming treatment for these stress
conditions. Results revealed that germination delayed in both
solutions, having variable germination with different priming
treatments. Germination, shoot and weight, root and shoot length
were higher but mean germination time and abnormal germination
percentage were lower in NaCl than Na2SO4 at the same water
potential. The root / shoot weight and R/S length increased with
increase in osmotic potential in both NaCl and Na2SO4 solutions.
NaCl had less inhibitor effect on seedling growth than the
germination. It was concluded that inhibition of germination at the
same water potential of NaCl and Na2SO4 resulted from salt toxicity
rather than osmotic effect. Hydro priming increased germination and
seedling growth under salt stress. This protocol has practical
importance and could be recommended to farmers to achieve higher
germination and uniform emergence under field conditions.
Abstract: There is need to explore emerging technologies based on carbon nanotube electronics as the MOS technology is approaching its limits. As MOS devices scale to the nano ranges, increased short channel effects and process variations considerably effect device and circuit designs. As a promising new transistor, the Carbon Nanotube Field Effect Transistor(CNTFET) avoids most of the fundamental limitations of the Traditional MOSFET devices. In this paper we present the analysis and comparision of a Carbon Nanotube FET(CNTFET) based 10(A current mirror with MOSFET for 32nm technology node. The comparision shows the superiority of the former in terms of 97% increase in output resistance,24% decrease in power dissipation and 40% decrease in minimum voltage required for constant saturation current. Furthermore the effect on performance of current mirror due to change in chirality vector of CNT has also been investigated. The circuit simulations are carried out using HSPICE model.
Abstract: The aim of this work is to study the elastic transfer
phenomenon which takes place in the elastic scattering of 16O on 12C
at energies near the Coulomb barrier. Where, the angular distribution
decrease steadily with increasing the scattering angle, then the cross
section will increase at backward angles due to the α-transfer process.
This reaction was also studied at different energies for tracking the
nuclear rainbow phenomenon. The experimental data of the angular
distribution at these energies were compared to the calculation
predictions. The optical potential codes such as SPIVAL and
Distorted Wave Born Approximation (DWUCK5) were used in
analysis.
Abstract: In this paper we present a new approach to detecting a
flaw in T.O.F.D (Time Of Flight Diffraction) type ultrasonic image
based on texture features. Texture is one of the most important
features used in recognizing patterns in an image. The paper
describes texture features based on 2D Gabor functions, i.e.,
Gaussian shaped band-pass filters, with dyadic treatment of the radial
spatial frequency range and multiple orientations, which represent an
appropriate choice for tasks requiring simultaneous measurement in
both space and frequency domains. The most relevant features are
used as input data on a Fuzzy c-mean clustering classifier. The
classes that exist are only two: 'defects' or 'no defects'. The proposed
approach is tested on the T.O.F.D image achieved at the laboratory
and on the industrial field.
Abstract: The objective of global optimization is to find the
globally best solution of a model. Nonlinear models are ubiquitous
in many applications and their solution often requires a global
search approach; i.e. for a function f from a set A ⊂ Rn to
the real numbers, an element x0 ∈ A is sought-after, such that
∀ x ∈ A : f(x0) ≤ f(x). Depending on the field of application,
the question whether a found solution x0 is not only a local minimum
but a global one is very important.
This article presents a probabilistic approach to determine the
probability of a solution being a global minimum. The approach is
independent of the used global search method and only requires a
limited, convex parameter domain A as well as a Lipschitz continuous
function f whose Lipschitz constant is not needed to be known.
Abstract: In this paper, we propose a new image segmentation approach for colour textured images. The proposed method for image segmentation consists of two stages. In the first stage, textural features using gray level co-occurrence matrix(GLCM) are computed for regions of interest (ROI) considered for each class. ROI acts as ground truth for the classes. Ohta model (I1, I2, I3) is the colour model used for segmentation. Statistical mean feature at certain inter pixel distance (IPD) of I2 component was considered to be the optimized textural feature for further segmentation. In the second stage, the feature matrix obtained is assumed to be the degraded version of the image labels and modeled as Markov Random Field (MRF) model to model the unknown image labels. The labels are estimated through maximum a posteriori (MAP) estimation criterion using ICM algorithm. The performance of the proposed approach is compared with that of the existing schemes, JSEG and another scheme which uses GLCM and MRF in RGB colour space. The proposed method is found to be outperforming the existing ones in terms of segmentation accuracy with acceptable rate of convergence. The results are validated with synthetic and real textured images.
Abstract: Moulded parts contribute to more than 70% of
components in products. However, common defects particularly in
plastic injection moulding exist such as: warpage, shrinkage, sink
marks, and weld lines. In this paper Taguchi experimental design
methods are applied to reduce the warpage defect of thin plate
Acrylonitrile Butadiene Styrene (ABS) and are demonstrated in two
levels; namely, orthogonal arrays of Taguchi and the Analysis of
Variance (ANOVA). Eight trials have been run in which the optimal
parameters that can minimize the warpage defect in factorial
experiment are obtained. The results obtained from ANOVA
approach analysis with respect to those derived from MINITAB
illustrate the most significant factors which may cause warpage in
injection moulding process. Moreover, ANOVA approach in
comparison with other approaches like S/N ratio is more accurate and
with the interaction of factors it is possible to achieve higher and the
better outcomes.
Abstract: Electrophoretic motion of a liquid droplet within an
uncharged cylindrical pore is investigated theoretically in this study. It
is found that the boundary effect in terms of the reduction of droplet
mobility (droplet velocity per unit strength of the applied electric field)
is very significant when the double layer surrounding the droplet is
thick, and diminishes as it gets very thin. Moreover, the viscosity ratio
of the ambient fluid to the internal one, σ, is a crucial factor in
determining its electrophoretic behavior. The boundary effect is less
significant as the viscosity ratio gets high. Up to 70% mobility
reduction is observed when this ratio is low (σ = 0.01), whereas only
40% reduction when it is high (σ = 100). The results of this study can
be utilized in various fields of biotechnology, such as a biosensor or a
lab-on-a-chip device.
Abstract: The paper presents the influence of the conventional
ploughing tillage technology in comparison with the minimum
tillage, upon the soil properties, weed control and yield in the case of
maize (Zea mays L.), soya-bean (Glycine hispida L.) and winter
wheat (Triticum aestivum L.) in a three years crop rotation. A
research has been conducted at the University of Agricultural
Sciences and Veterinary Medicine Cluj-Napoca, Romania. The use of
minimum soil tillage systems within a three years rotation: maize,
soya-bean, wheat favorites the rise of the aggregates hydro stability
with 5.6-7.5% on a 0-20 cm depth and 5-11% on 20-30 cm depth.
The minimum soil tillage systems – paraplow, chisel or rotary grape
– are polyvalent alternatives for basic preparation, germination bed
preparation and sowing, for fields and crops with moderate loose
requirements being optimized technologies for: soil natural fertility
activation and rationalization, reduction of erosion, increasing the
accumulation capacity for water and realization of sowing in the
optimal period. The soil tillage system influences the productivity
elements of cultivated species and finally the productions thus
obtained. Thus, related to conventional working system, the
productions registered in minimum tillage working represented 89-
97% in maize, 103-112% in soya-bean, 93-99% in winter-wheat. The
results of investigations showed that the yield is a conclusion soil
tillage systems influence on soil properties, plant density assurance
and on weed control. Under minimum tillage systems in the case of
winter weat as an option for replacing classic ploughing, the best
results in terms of quality indices were obtained from version worked
with paraplow, followed by rotary harrow and chisel. At variants
worked with paraplow were obtained quality indices close to those of
the variant worked with plow, and protein and gluten content was
even higher. At Ariesan variety, highest protein content, 12.50% and
gluten, 28.6% was obtained for the variant paraplow.
Abstract: The conventional production of biodiesel from crude
palm oil which contains large amounts of free fatty acids in the
presence of a homogeneous base catalyst confronts the problems of
soap formation and very low yield of biodiesel. To overcome these
problems, free fatty acids must be esterified to their esters in the
presence of an acid catalyst prior to alkaline-catalyzed
transesterification. Sulfated metal oxides are a promising group of
catalysts due to their very high acidity. In this research, aluminadoped
sulfated tin oxide (SO4
2-/Al2O3-SnO2) catalysts were prepared
and used for esterification of free fatty acids in crude palm oil in a
batch reactor. The SO4
2-/Al2O3-SnO2 catalysts were prepared from
different Al precursors. The results showed that different Al
precursors gave different activities of the SO4
2-/Al2O3-SnO2 catalysts.
The esterification of free fatty acids in crude palm oil with methanol
in the presence of SO4
2-/Al2O3-SnO2 catalysts followed first-order
kinetics.
Abstract: Titanium nitride (TiN) has been synthesized using the
sheet plasma negative ion source (SPNIS). The parameters used for
its effective synthesis has been determined from previous
experiments and studies. In this study, further enhancement of the
deposition rate of TiN synthesis and advancement of the SPNIS
operation is presented. This is primarily achieved by the addition of
Sm-Co permanent magnets and a modification of the configuration in
the TiN deposition process. The magnetic enhancement is aimed at
optimizing the sputtering rate and the sputtering yield of the process.
The Sm-Co permanent magnets are placed below the Ti target for
better sputtering by argon. The Ti target is biased from –250V to –
350V and is sputtered by Ar plasma produced at discharge current of
2.5–4A and discharge potential of 60–90V. Steel substrates of
dimensions 20x20x0.5mm3 were prepared with N2:Ar volumetric
ratios of 1:3, 1:5 and 1:10. Ocular inspection of samples exhibit
bright gold color associated with TiN. XRD characterization
confirmed the effective TiN synthesis as all samples exhibit the (200)
and (311) peaks of TiN and the non-stoichiometric Ti2N (220) facet.
Cross-sectional SEM results showed increase in the TiN deposition
rate of up to 0.35μm/min. This doubles what was previously obtained
[1]. Scanning electron micrograph results give a comparative
morphological picture of the samples. Vickers hardness results gave
the largest hardness value of 21.094GPa.
Abstract: A two-dimensional moving mesh algorithm is developed to simulate the general motion of two rotating bodies with relative translational motion. The grid includes a background grid and two sets of grids around the moving bodies. With this grid arrangement rotational and translational motions of two bodies are handled separately, with no complications. Inter-grid boundaries are determined based on their distances from two bodies. In this method, the overset concept is applied to hybrid grid, and flow variables are interpolated using a simple stencil. To evaluate this moving mesh algorithm unsteady Euler flow is solved for different cases using dual-time method of Jameson. Numerical results show excellent agreement with experimental data and other numerical results. To demonstrate the capability of present algorithm for accurate solution of flow fields around moving bodies, some benchmark problems have been defined in this paper.
Abstract: Competitive relationships among Bradyrhizobium
japonicum USDA serogroup 123, 122 and 138 were screened versus
the standard commercial soybean variety Williams and two
introductions P1 377578 "671" in a field trial. Displacement of strain
123 by an effective strain should improved N2 fixation. Root nodules
were collected and strain occupancy percentage was determined
using strain specific fluorescent antibodies technique. As anticipated
the strain USDA 123 dominated 92% of nodules due to the high
affinity between the host and the symbiont. This dominance was
consistent and not changed materially either by inoculation practice
or by introducing new strainan. The interrelationship between the
genotype Williams and serogroup 122 & 138 was found very weak
although the cell density of the strain in the rhizosphere area was
equal. On the other hand, the nodule occupancy of genotypes 671 and
166 with rhizobia serogroup 123 was almost diminished to zero. .
The data further exhibited that the genotypes P1 671 and P1 166 have
high affinity to colonize with strains 122 and 138 whereas Williams
was highly promiscuous to strain 123.
Abstract: Stair climbing is one of critical issues for field robots to
widen applicable areas. This paper presents optimal design on
kinematic parameters of a new robotic platform for stair climbing. The
robotic platform climbs various stairs by body flip locomotion with
caterpillar type main platform. Kinematic parameters such as platform
length, platform height, and caterpillar rotation speed are optimized to
maximize stair climbing stability. Three types of stairs are used to
simulate typical user conditions. The optimal design process is
conducted based on Taguchi methodology, and resulting parameters
with optimized objective function are presented. In near future, a
prototype is assembled for real environment testing.
Abstract: This study aims to screen out and to optimize the
major nutrients for maximum carotenoid production and
antioxidation characteristics by Rhodotorula rubra. It was found that
supplementary of 10 g/l glucose as carbon source, 1 g/l ammonium
sulfate as nitrogen source and 1 g/l yeast extract as growth factor in
the medium provided the better yield of carotenoid content of 30.39
μg/g cell dry weight the amount of antioxidation of Rhodotorula
rubra by DPPH, ABTS and MDA method were 1.463%, 34.21% and
34.09 μmol/l, respectively.
Abstract: This study explores how the mechanics of learning
paves the way to engineering innovation. Theories related to learning
in the new product/service innovation are reviewed from an
organizational perspective, behavioral perspective, and engineering
perspective. From this, an engineering team-s external interactions
for knowledge brokering and internal composition for skill balance
are examined from a learning and innovation viewpoints. As a result,
an integrated learning model is developed by reconciling the
theoretical perspectives as well as developing propositions that
emphasize the centrality of learning, and its drivers, in the
engineering product/service development. The paper also provides a
review and partial validation of the propositions using the results of a
previously published field study in the aerospace industry.
Abstract: This paper presents a CFD analysis of the flow around
a 30° inclined flat plate of infinite span. Numerical predictions have
been compared to experimental measurements, in order to assess the
potential of the finite volume code of determining the aerodynamic
forces acting on a flat plate invested by a fluid stream of infinite
extent.
Several turbulence models and spatial node distributions have
been tested and flow field characteristics in the neighborhood of the
flat plate have been numerically investigated, allowing the
development of a preliminary procedure to be used as guidance in
selecting the appropriate grid configuration and the corresponding
turbulence model for the prediction of the flow field over a twodimensional
inclined plate.
Abstract: BioEnergy is an archetypal appropriate technology
and alternate source of energy in rural areas of China, and can meet
the basic need for cooking fuel in rural areas. The paper introduces
with an alternate mean of research that can accelerate the biogas
energy production. Tithonia diversifolia or the Tree marigold can be
hailed as mesophillic anaerobic digestion to increase the production
of more Bioenergy. Tithonia diversifolia is very native to Mexico and
Central America, which can be served as ornamental plants- green
manure and can prevent soil erosion. Tithonia diversifolia is widely
grown and known to Asia, Africa, America and Australia as well.
Nowadays, Considering China’s geographical condition it is found
that Tithonia diversifolia is widely growing plant in the many tropical
and subtropical regions of southern Yunnan- which can have great
usage in accelerating and increasing the Bioenergy production
technology. The paper discussed aiming at proving possibility that
Tithonia diversifolia can be applied in biogas fermentation and its
biogas production potential, the research carried experiment on
Tithonia diversifolia biogas fermentation under the mesophilic
condition (35 Celsius Degree). The result revealed that Tithonia
diversifolia can be used as biogas fermentative material, and 6%
concentration can get the best biogas production, with the TS biogas
production rate 656mL/g and VS biogas production rate 801mL/g. It
is well addressed that Tithonia diversifolia grows wildly in 53
Counties and 9 cities of Yunnan Province, which mainly grows in
form of the road side plants, the edge of the field, countryside, forest
edge, open space; of which demersum-natures can form dense
monospecific beds -causing serious harm to agricultural production
landforms threatening the ecological system as a potentially harmful
exotic plant. There are also found the three types of invasive daisy
alien plants -Eupatorium adenophorum, Eupatorium Odorata and
Tithonia diversifolia in Yunnan Province of China-among them the
Tithonia diversifolia is responsible for causing serious harm to
agricultural production. In this paper we have designed the
experimental explanation of Biogas energy production that requires
anaerobic environment and some microbes; Tithonia diversifolia
plant has been taken into consideration while carrying experiments
and with successful resulting of generating more BioEnergy
emphasizing on the practical applications of Tithonia diversifolia.
This paper aims at- to find a new mechanism to provide a more
scientific basis for the development of this plant herbicides in Biogas
energy and to improve the utilization throughout the world as well.
Abstract: The development of aid's systems for the medical
diagnosis is not easy thing because of presence of inhomogeneities in
the MRI, the variability of the data from a sequence to the other as
well as of other different source distortions that accentuate this
difficulty. A new automatic, contextual, adaptive and robust
segmentation procedure by MRI brain tissue classification is
described in this article. A first phase consists in estimating the
density of probability of the data by the Parzen-Rozenblatt method.
The classification procedure is completely automatic and doesn't
make any assumptions nor on the clusters number nor on the
prototypes of these clusters since these last are detected in an
automatic manner by an operator of mathematical morphology called
skeleton by influence zones detection (SKIZ). The problem of
initialization of the prototypes as well as their number is transformed
in an optimization problem; in more the procedure is adaptive since it
takes in consideration the contextual information presents in every
voxel by an adaptive and robust non parametric model by the
Markov fields (MF). The number of bad classifications is reduced by
the use of the criteria of MPM minimization (Maximum Posterior
Marginal).
Abstract: A three-year field experiment (2010-2012) was
conducted to determine the abundance of epiphytic and endophytic
filamentous fungi colonizing the grain of winter wheat cv. Bogatka.
Wheat spikes were protected with tebuconazole or chitosan at the
watery ripe stage. Untreated plants served as control. Tebuconazole
exerted an inhibitory effect primarily on F. culmorum and F.
graminearum, and its effectiveness was determined by the pressure
from pathogens that infected wheat spikes during the growing season.
Chitosan did not suppress the growth of Fusarium species and
Alternaria alternata.