Abstract: Impinging jets are used in various industrial areas as a cooling and drying technique. The current research is concerned with the means of improving the heat transfer for configurations with a minimum distance of the nozzle to the impingement surface. The impingement heat transfer is described using numerical methods over a wide range of parameters for an array of planar jets. These parameters include varying jet flow speed, width of nozzle, distance of nozzle, angle of the jet flow, velocity and geometry of the impingement surface. Normal pressure and shear stress are computed as additional parameters. Using dimensionless characteristic numbers the parameters and the results are correlated to gain generalized equations. The results demonstrate the effect of the investigated parameters on the flow.
Abstract: The present energy situation and the concerns
about global warming has stimulated active research interest
in non-petroleum, carbon free compounds and non-polluting
fuels, particularly for transportation, power generation, and
agricultural sectors. Environmental concerns and limited
amount of petroleum fuels have caused interests in the
development of alternative fuels for internal combustion (IC)
engines. The petroleum crude reserves however, are declining
and consumption of transport fuels particularly in the
developing countries is increasing at high rates. Severe
shortage of liquid fuels derived from petroleum may be faced
in the second half of this century. Recently more and more
stringent environmental regulations being enacted in the USA
and Europe have led to the research and development
activities on clean alternative fuels. Among the gaseous fuels
hydrogen is considered to be one of the clean alternative fuel.
Hydrogen is an interesting candidate for future internal
combustion engine based power trains. In this experimental
investigation, the performance and combustion analysis were
carried out on a direct injection (DI) diesel engine using
hydrogen with diesel following the TMI(Time Manifold
Injection) technique at different injection timings of 10
degree,45 degree and 80 degree ATDC using an electronic
control unit (ECU) and injection durations were controlled.
Further, the tests have been carried out at a constant speed of
1500rpm at different load conditions and it can be observed
that brake thermal efficiency increases with increase in load
conditions with a maximum gain of 15% at full load
conditions during all injection strategies of hydrogen. It was
also observed that with the increase in hydrogen energy share
BSEC started reducing and it reduced to a maximum of 9% as
compared to baseline diesel at 10deg ATDC injection during
maximum injection proving the exceptional combustion
properties of hydrogen.
Abstract: In areas of low to moderate seismicity many building contents and equipment are not positively fixed to the floor or tied to adjacent walls. Under seismic induced horizontal vibration, such contents and equipment can suffer from damage by either overturning or impact associated with rocking. This paper focuses on the estimation of shock on typical contents and equipment due to rocking. A simplified analytical model is outlined that can be used to estimate the maximum acceleration on a rocking object given its basic geometric and mechanical properties. The developed model was validated against experimental results. The experimental results revealed that the maximum shock acceleration can be underestimated if the static stiffness of the materials at the interface between the rocking object and floor is used rather than the dynamic stiffness. Excellent agreement between the model and experimental results was found when the dynamic stiffness for the interface material was used, which was found to be generally much higher than corresponding static stiffness under different investigated boundary conditions of the cushion. The proposed model can be a beneficial tool in performing a rapid assessment of shock sensitive components considered for possible seismic rectification.
Abstract: In order to upgrade the seismic resistibility of structures and enhance the functionality of an isolator, a new base isolator called the multiple trench friction pendulum system (MTFPS) is proposed in this study. The proposed MTFPS isolator is composed of a trench concave surface and several intermediate sliding plates in two orthogonal directions. Mathematical formulations have been derived to examine the characteristics of the proposed MTFPS isolator possessing multiple intermediate sliding plates. By means of mathematical formulations, it can be inferred that the natural period and damping effect of the MTFPS isolator with several intermediate sliding plates can be altered continually and controllably during earthquakes. Furthermore, results obtained from shaking table tests demonstrate that the proposed isolator provides good protection to structures for prevention of damage from strong earthquakes.
Abstract: SEMG (Surface Electromyogram) is one of the
bio-signals and is generated from the muscle. And there are many
research results that use forearm EMG to detect hand motions. In this
paper, we will talk about our developed the robot hand system that can
control grasping power by SEMG. In our system, we suppose that
muscle power is proportional to the amplitude of SEMG. The power is
estimated and the grip power of a robot hand is able to be controlled
using estimated muscle power in our system. In addition, to perform a
more precise control can be considered to build a closed loop feedback
system as an object to a subject to pressure from the edge of hand. Our
objectives of this study are the development of a method that makes
perfect detection of the hand grip force possible using SEMG patterns,
and applying this method to the man-machine interface.
Abstract: Article presents the geometry and structure
reconstruction procedure of the aircraft model for flatter research
(based on the I22-IRYDA aircraft). For reconstruction the Reverse
Engineering techniques and advanced surface modeling CAD tools
are used. Authors discuss all stages of data acquisition process,
computation and analysis of measured data. For acquisition the three
dimensional structured light scanner was used. In the further sections,
details of reconstruction process are present. Geometry
reconstruction procedure transform measured input data (points
cloud) into the three dimensional parametric computer model
(NURBS solid model) which is compatible with CAD systems.
Parallel to the geometry of the aircraft, the internal structure
(structural model) are extracted and modeled. In last chapter the
evaluation of obtained models are discussed.
Abstract: A gold coated copper rotating electrode was used to
eliminate surface oxidation effect. This study examined the effect of
electrode rotation on the ozone generation process and showed that an
ozonizer with an electrode rotating system might be a possible way to
increase ozone-synthesis efficiency. Two new phenomena appeared
during experiments with the rotating electrode. First was that ozone
concentration increased to about two times higher than that of the case
with no rotation. Second, input power and discharge area were found
to increase with the rotation speed. Both ozone concentration and
ozone production efficiency improved in the case of rotating electrode
compared to the case with a non-rotating electrode. One possible
reason for this was the increase in discharge length of
micro-discharges during electrode rotation. The rotating electrode
decreased onset voltage, while reactor capacitance increased with
rotation. Use of a rotating-type electrode allowed earlier observation
of the ozone zero phenomena compared with a non-rotating electrode
because, during rotation, the entire electrode surface was functional,
allowing nitrogen on the electrode surface to be evenly consumed.
Nitrogen demand increased with increasing rotation s
Abstract: The main purpose of the dam is to control the surface
streams and rivers across the country. Dam construction and
formation of river and big water reservoirs and resources happen in
the glen is a big incident which would change its surrounding area
considerably. In fact, constructing a dam the glen width is close and
fishes don't migrate from upstream to downstream and ultimately it
would led to their death. To resolve this, it seems necessity to create a
passage for fishes during the construction of dam. It is provided
establishing a set of stepped pools overlooking each other as a fish
way or fish ladder a proper pathway for moving fishes. In this article
we first examine the surrounding environment and then Ghazal Ozon
River and preserving the aquatics.
Abstract: Faced with social and health system capacity
constraints and rising and changing demand for welfare services,
governments and welfare providers are increasingly relying on
innovation to help support and enhance services. However, the
evidence reported by several studies indicates that the realization of
that potential is not an easy task. Innovations can be deemed
inherently complex to implement and operate, because many of them
involve a combination of technological and organizational renewal
within an environment featuring a diversity of stakeholders. Many
public welfare service innovations are markedly systemic in their
nature, which means that they emerge from, and must address, the
complex interplay between political, administrative, technological,
institutional and legal issues. This paper suggests that stakeholders
dealing with systemic innovation in welfare services must deal with
ambiguous and incomplete information in circumstances of
uncertainty. Employing a literature review methodology and case
study, this paper identifies, categorizes and discusses different
aspects of the uncertainty of systemic innovation in public welfare
services, and argues that uncertainty can be classified into eight
categories: technological uncertainty, market uncertainty,
regulatory/institutional uncertainty, social/political uncertainty,
acceptance/legitimacy uncertainty, managerial uncertainty, timing
uncertainty and consequence uncertainty.
Abstract: A new digital watermarking technique for images that
are sensitive to blocking artifacts is presented. Experimental results
show that the proposed MDCT based approach produces highly
imperceptible watermarked images and is robust to attacks such as
compression, noise, filtering and geometric transformations. The
proposed MDCT watermarking technique is applied to fingerprints
for ensuring security. The face image and demographic text data of
an individual are used as multiple watermarks. An AFIS system was
used to quantitatively evaluate the matching performance of the
MDCT-based watermarked fingerprint. The high fingerprint
matching scores show that the MDCT approach is resilient to
blocking artifacts. The quality of the extracted face and extracted text
images was computed using two human visual system metrics and
the results show that the image quality was high.
Abstract: The development of shape and size of a crack in a
pressure vessel under uniaxial and biaxial loadings is important in
fitness-for-service evaluations such as leak-before-break. In this
work finite element modelling was used to evaluate the mean stress
and the J-integral around a front of a surface-breaking crack. A
procedure on the basis of ductile tearing resistance curves of high and
low constrained fracture mechanics geometries was developed to
estimate the amount of ductile crack extension for surface-breaking
cracks and to show the evolution of the initial crack shape. The
results showed non-uniform constraint levels and crack driving forces
around the crack front at large deformation levels. It was also shown
that initially semi-elliptical surface cracks under biaxial load
developed higher constraint levels around the crack front than in
uniaxial tension. However similar crack shapes were observed with
more extensions associated with cracks under biaxial loading.
Abstract: Toughening of polyamide 6 (PA6)/ Nanoclay (NC) nanocomposites with styrene-ethylene/butadiene-styrene copolymer (SEBS) using maleated styrene-ethylene/butadiene-styrene copolymer (mSEBS)/ as a compatibilizer were investigated by blending them in a co-rotating twin-screw extruder. Response surface method of experimental design was used for optimizing the material and processing parameters. Effect of four factors, including SEBS, mSEBS and NC contents as material variables and order of mixing as a processing factor, on toughness of hybrid nanocomposites were studied. All the prepared samples showed ductile behavior and low temperature Izod impact toughness of some of the hybrid nanocomposites demonstrated 900% improvement compared to the PA6 matrix while the modulus showed maximum enhancement of 20% compared to the pristine PA6 resin.
Abstract: Subjective loneliness describes people who feel a
disagreeable or unacceptable lack of meaningful social relationships,
both at the quantitative and qualitative level. The studies to be
presented tested an Italian 18-items self-report loneliness measure,
that included items adapted from scales previously developed,
namely a short version of the UCLA (Russell, Peplau and Cutrona,
1980), and the 11-items Loneliness scale by De Jong-Gierveld &
Kamphuis (JGLS; 1985). The studies aimed at testing the developed
scale and at verifying whether loneliness is better conceptualized as a
unidimensional (so-called 'general loneliness') or a bidimensional
construct, namely comprising the distinct facets of social and
emotional loneliness. The loneliness questionnaire included 2 singleitem
criterion measures of sad mood, and social contact, and asked
participants to supply information on a number of socio-demographic
variables. Factorial analyses of responses obtained in two
preliminary studies, with 59 and 143 Italian participants respectively,
showed good factor loadings and subscale reliability and confirmed
that perceived loneliness has clearly two components, a social and an
emotional one, the latter measured by two subscales, a 7-item
'general' loneliness subscale derived from UCLA, and a 6–item
'emotional' scale included in the JGLS. Results further showed that
type and amount of loneliness are related, negatively, to frequency of
social contacts, and, positively, to sad mood. In a third study data
were obtained from a nation-wide sample of 9.097 Italian subjects,
12 to about 70 year-olds, who filled the test on-line, on the Italian
web site of a large-audience magazine, Focus. The results again
confirmed the reliability of the component subscales, namely social,
emotional, and 'general' loneliness, and showed that they were
highly correlated with each other, especially the latter two.
Loneliness scores were significantly predicted by sex, age, education
level, sad mood and social contact, and, less so, by other variables –
e.g., geographical area and profession. The scale validity was
confirmed by the results of a fourth study, with elderly men and
women (N 105) living at home or in residential care units. The three
subscales were significantly related, among others, to depression, and
to various measures of the extension of, and satisfaction with, social
contacts with relatives and friends. Finally, a fifth study with 315
career-starters showed that social and emotional loneliness correlate
with life satisfaction, and with measures of emotional intelligence.
Altogether the results showed a good validity and reliability in the
tested samples of the entire scale, and of its components.
Abstract: A new technique to quantify the differential mode
delay (DMD) in multimode fiber (MMF) is been presented. The
technique measures DMD based on angular launch and
measurements of the difference in modal delay using variable
apertures at the fiber face. The result of the angular spatial filtering
revealed less excitation of higher order modes when the laser beam is
filtered at higher angles. This result would indicate that DMD
profiles would experience a data pattern dependency.
Abstract: In this work the numerical simulation of transient heat
transfer in a cylindrical probe is done. An experiment was conducted
introducing a steel cylinder in a heating chamber and registering its
surface temperature along the time during one hour. In parallel, a
mathematical model was solved for one dimension transient heat
transfer in cylindrical coordinates, considering the boundary
conditions of the test. The model was solved using finite difference
method, because the thermal conductivity in the cylindrical steel bar
and the convection heat transfer coefficient used in the model are
considered temperature dependant functions, and both conditions
prevent the use of the analytical solution. The comparison between
theoretical and experimental results showed the average deviation is
below 2%. It was concluded that numerical methods are useful in
order to solve engineering complex problems. For constant k and h,
the experimental methodology used here can be used as a tool for
teaching heat transfer in mechanical engineering, using mathematical
simplified models with analytical solutions.
Abstract: Currently electronic slide (e-slide) is one of the most common styles in educational presentation. Unfortunately, the utilization of e-slide for the visually impaired is uncommon since they are unable to see the content of such e-slides which are usually composed of text, images and animation. This paper proposes a model for presenting e-slide in multimodal presentation i.e. using conventional slide concurrent with voicing, in both languages Malay and English. At the design level, live multimedia presentation concept is used, while at the implementation level several components are used. The text content of each slide is extracted using COM component, Microsoft Speech API for voicing the text in English language and the text in Malay language is voiced using dictionary approach. To support the accessibility, an auditory user interface is provided as an additional feature. A prototype of such model named as VSlide has been developed and introduced.
Abstract: In this paper we present a computational model for pronominal anaphora resolution in Turkish. The model is based on Hobbs’ Naїve Algorithm [4, 5, 6], which exploits only the surface syntax of sentences in a given text.
Abstract: For the characterization of the weld defect region in the radiographic image, looking for features which are invariant regarding the geometrical transformations (rotation, translation and scaling) proves to be necessary because the same defect can be seen from several angles according to the orientation and the distance from the welded framework to the radiation source. Thus, panoply of geometrical attributes satisfying the above conditions is proposed and which result from the calculation of the geometrical parameters (surface, perimeter, etc.) on the one hand and the calculation of the different order moments, on the other hand. Because the large range in values of the raw features and taking into account other considerations imposed by some classifiers, the scaling of these values to lie between 0 and 1 is indispensable. The principal component analysis technique is used in order to reduce the number of the attribute variables in the aim to give better performance to the further defect classification.
Abstract: In the present work, we have developed a symmetric electrochemical capacitor based on the nanostructured iron oxide (Fe3O4)-activated carbon (AC) nanocomposite materials. The physical properties of the nanocomposites were characterized by Scanning Electron Microscopy (SEM) and Brunauer-Emmett-Teller (BET) analysis. The electrochemical performances of the composite electrode in 1.0 M Na2SO3 and 1.0 M Na2SO4 aqueous solutions were evaluated using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The composite electrode with 4 wt% of iron oxide nanomaterials exhibits the highest capacitance of 86 F/g. The experimental results clearly indicate that the incorporation of iron oxide nanomaterials at low concentration to the composite can improve the capacitive performance, mainly attributed to the contribution of the pseudocapacitance charge storage mechanism and the enhancement on the effective surface area of the electrode. Nevertheless, there is an optimum threshold on the amount of iron oxide that needs to be incorporated into the composite system. When this optimum threshold is exceeded, the capacitive performance of the electrode starts to deteriorate, as a result of the undesired particle aggregation, which is clearly indicated in the SEM analysis. The electrochemical performance of the composite electrode is found to be superior when Na2SO3 is used as the electrolyte, if compared to the Na2SO4 solution. It is believed that Fe3O4 nanoparticles can provide favourable surface adsorption sites for sulphite (SO3 2-) anions which act as catalysts for subsequent redox and intercalation reactions.
Abstract: The objective is to split a simply connected polygon
into a set of convex quadrilaterals without inserting new
boundary nodes. The presented approach consists in repeatedly
removing quadrilaterals from the polygon. Theoretical results
pertaining to quadrangulation of simply connected polygons are
derived from the usual 2-ear theorem. It produces a quadrangulation
technique with O(n) number of quadrilaterals. The
theoretical methodology is supplemented by practical results
and CAD surface segmentation.