Abstract: The dynamics of Min proteins plays a center role in
accurate cell division. Although the nucleoids may presumably play
an important role in prokaryotic cell division, there is a lack of
models to account for its participation. In this work, we apply the
lattice Boltzmann method to investigate protein oscillation based on a
mesoscopic model that takes into account the nucleoid-s role. We
found that our numerical results are in reasonably good agreement
with the previous experimental results On comparing with the other
computational models without the presence of nucleoids, the
highlight of our finding is that the local densities of MinD and MinE
on the cytoplasmic membrane increases, especially along the cell
width, when the size of the obstacle increases, leading to a more
distinct cap-like structure at the poles. This feature indicated the
realistic pattern and reflected the combination of Min protein
dynamics and nucleoid-s role.
Abstract: Heating is inevitable in any bearing operation. This
leads to not only the thinning of the lubricant but also could lead to a
thermal deformation of the bearing. The present work is an attempt to
analyze the influence of thermal deformation on the thermohydrodynamic
lubrication of infinitely long tilted pad slider rough
bearings. As a consequence of heating the slider is deformed and is
assumed to take a parabolic shape. Also the asperities expand leading
to smaller effective film thickness. Two different types of surface
roughness are considered: longitudinal roughness and transverse
roughness. Christensen-s stochastic approach is used to derive the
Reynolds-type equations. Density and viscosity are considered to be
temperature dependent. The modified Reynolds equation, momentum
equation, continuity equation and energy equation are decoupled and
solved using finite difference method to yield various bearing
characteristics. From the numerical simulations it is observed that the
performance of the bearing is significantly affected by the thermal
distortion of the slider and asperities and even the parallel sliders
seem to carry some load.
Abstract: This work presents a new algorithm based on a combination of fuzzy (FUZ), Dynamic Programming (DP), and Genetic Algorithm (GA) approach for capacitor allocation in distribution feeders. The problem formulation considers two distinct objectives related to total cost of power loss and total cost of capacitors including the purchase and installation costs. The novel formulation is a multi-objective and non-differentiable optimization problem. The proposed method of this article uses fuzzy reasoning for sitting of capacitors in radial distribution feeders, DP for sizing and finally GA for finding the optimum shape of membership functions which are used in fuzzy reasoning stage. The proposed method has been implemented in a software package and its effectiveness has been verified through a 9-bus radial distribution feeder for the sake of conclusions supports. A comparison has been done among the proposed method of this paper and similar methods in other research works that shows the effectiveness of the proposed method of this paper for solving optimum capacitor planning problem.
Abstract: The main objective of this research was to investigate
the biosorption capacity for biofilms of sulphate reducing bacteria
(SRB) to remove heavy metals, such as Zn, Pb and Cd from
rainwater using laboratory-scale reactors containing mixed support
media. Evidence showed that biosorption had contributed to removal
of heavy metals including Zn, Pb and Cd in presence of SRB and
SRB were also found in the aqueous samples from reactors.
However, the SRB and specific families (Desulfobacteriaceae and
Desulfovibrionaceae) were found mainly in the biomass samples
taken from all reactors at the end of the experiment. EDX-analysis
of reactor solids at end of experiment showed that heavy metals Zn,
Pb and Cd had also accumulated in these precipitates.
Abstract: The use of composite materials in offshore engineering for deep sea oil production riser systems has drawn considerable interest due to the potential weight savings and improvement in durability. The design of composite risers consists of two stages: (1) local design based on critical local load cases, and (2) global analysis of the full length composite riser under global loads and assessment of critical locations. In the first stage, eight different material combinations were selected and their laminate configurations optimised under local load considerations. Stage two includes a final local stress analysis of the critical sections of the riser under the combined loads determined in the global analysis. This paper describes two design methodologies of the composite riser to provide minimum structural weight and shows that the use of off angle fibre orientations in addition to axial and hoop reinforcements offer substantial weight savings and ensure the structural capacity.
Abstract: The National Bridge Inventory (NBI) includes more
than 600,000 bridges within the United States of America.
Prestressed concrete girder bridges represent one of the most widely
used bridge systems. The majority of these girder bridges were
constructed using 0.5 and 0.6 inch diameter strands. The main
impediments to using larger strand diameters are: 1) lack of prestress
bed capacities, 2) lack of structural knowledge regarding the transfer
and development length of larger strands, and 3) the possibility of
developing wider end zone cracks upon strand release.
This paper presents a study about using 0.7 inch strands in girder
fabrication. Transfer and development length were evaluated, and
girders were fabricated using 0.7 inch strands at different spacings.
Results showed that 0.7 inch strands can be used at 2.0 inch spacing
without violating the AASHTO LRFD Specifications, while attaining
superior performance in shear and flexure.
Abstract: A universal current-mode biquad is described which
represents an economical variant of well-known KHN (Kerwin,
Huelsman, Newcomb) voltage-mode filter. The circuit consists of
two multiple-output OTAs and of two grounded capacitors. Utilizing
simple splitter of the input current and a pair of jumpers, all the basic
2nd-order transfer functions can be implemented. The principle is
verified by Spice simulation on the level of a CMOS structure of
OTAs.
Abstract: This paper presents a portable robot that is to use for
welding process in shipbuilding yard. It has six degree of freedom and
3kg payload capability. Its weight is 21.5kg so that human workers can
carry it to the work place. Its body mainly made of magnesium alloy
and aluminum alloy for few parts that require high strength. Since the
distance between robot and controller should be 50m at most, the robot
controller controls the robot through EtherCAT. RTX and KPA are
used for real time EtherCAT control on Windows XP. The
performance of the developed robot was satisfactory, in welding of U
type cell in shipbuilding yard.
Abstract: CIM is the standard formalism for modeling management
information developed by the Distributed Management Task
Force (DMTF) in the context of its WBEM proposal, designed to
provide a conceptual view of the managed environment. In this
paper, we propose the inclusion of formal knowledge representation
techniques, based on Description Logics (DLs) and the Web Ontology
Language (OWL), in CIM-based conceptual modeling, and then we
examine the benefits of such a decision. The proposal is specified
as a CIM metamodel level mapping to a highly expressive subset
of DLs capable of capturing all the semantics of the models. The
paper shows how the proposed mapping provides CIM diagrams with
precise semantics and can be used for automatic reasoning about the
management information models, as a design aid, by means of newgeneration
CASE tools, thanks to the use of state-of-the-art automatic
reasoning systems that support the proposed logic and use algorithms
that are sound and complete with respect to the semantics. Such a
CASE tool framework has been developed by the authors and its
architecture is also introduced. The proposed formalization is not
only useful at design time, but also at run time through the use of
rational autonomous agents, in response to a need recently recognized
by the DMTF.
Abstract: This article presents a simple way to perform programmed voice commands for the interface with commercial Digital and Analogue Input/Output PCI cards, used in Robotics and Automation applications. Robots and Automation equipment can "listen" to voice commands and perform several different tasks, approaching to the human behavior, and improving the human- machine interfaces for the Automation Industry. Since most PCI Digital and Analogue Input/Output cards are sold with several DLLs included (for use with different programming languages), it is possible to add speech recognition capability, using a standard speech recognition engine, compatible with the programming languages used. It was created in this work a Visual Basic 6 (the world's most popular language) application, that listens to several voice commands, and is capable to communicate directly with several standard 128 Digital I/O PCI Cards, used to control complete Automation Systems, with up to (number of boards used) x 128 Sensors and/or Actuators.
Abstract: Road Traffic Accidents are a major cause of disability and death throughout the world. The control of intelligent vehicles in order to reduce human error and boost ease congestion is not accomplished solely by the aid of human resources. The present article is an attempt to introduce an intelligent control system based on RFID technology. By the help of RFID technology, vehicles are connected to computerized systems, intelligent light poles and other available hardware along the way. In this project, intelligent control system is capable of tracking all vehicles, crisis management and control, traffic guidance and recording Driving offences along the highway.
Abstract: Capacitive electrocardiogram (ECG) measurement is an attractive approach for long-term health monitoring. However, there is little literature available on its implementation, especially for multichannel system in standard ECG leads. This paper begins from the design criteria for capacitive ECG measurement and presents a multichannel limb-lead capacitive ECG system with conductive fabric tapes pasted on a double layer PCB as the capacitive sensors. The proposed prototype system incorporates a capacitive driven-body (CDB) circuit to reduce the common-mode power-line interference (PLI). The presented prototype system has been verified to be stable by theoretic analysis and practical long-term experiments. The signal quality is competitive to that acquired by commercial ECG machines. The feasible size and distance of capacitive sensor have also been evaluated by a series of tests. From the test results, it is suggested to be greater than 60 cm2 in sensor size and be smaller than 1.5 mm in distance for capacitive ECG measurement.
Abstract: In this paper the Laplace Decomposition method is developed to solve linear and nonlinear fractional integro- differential equations of Volterra type.The fractional derivative is described in the Caputo sense.The Laplace decomposition method is found to be fast and accurate.Illustrative examples are included to demonstrate the validity and applicability of presented technique and comparasion is made with exacting results.
Abstract: In the supply chain management customer is the most
significant component and mass customization is mostly related to
customers because it is the capability of any industry or organization
to deliver highly customized products and its services to the
respective customers with flexibility and integration, providing such
a variety of products that nearly everyone can find what they want.
Today all over the world many companies and markets are facing
varied situations that at one side customers are demanding that their
orders should be completed as quickly as possible while on other
hand it requires highly customized products and services. By
applying mass customization some companies face unwanted cost
and complexity. Now they are realizing that they should completely
examine what kind of customization would be best suited for their
companies. In this paper authors review some approaches and
principles which show effect in supply chain management that can be
adopted and used by companies for quickly meeting the customer
orders at reduced cost, with minimum amount of inventory and
maximum efficiency.
Abstract: Energy Efficiency Management is the heart of a
worldwide problem. The capability of a multi-agent system as a
technology to manage the micro-grid operation has already been
proved. This paper deals with the implementation of a decisional
pattern applied to a multi-agent system which provides intelligence to
a distributed local energy network considered at local consumer level.
Development of multi-agent application involves agent
specifications, analysis, design, and realization. Furthermore, it can
be implemented by following several decisional patterns. The
purpose of present article is to suggest a new approach for a
decisional pattern involving a multi-agent system to control a
distributed local energy network in a decentralized competitive
system. The proposed solution is the result of a dichotomous
approach based on environment observation. It uses an iterative
process to solve automatic learning problems and converges
monotonically very fast to system attracting operation point.
Abstract: For the communication between human and computer
in an interactive computing environment, the gesture recognition is
studied vigorously. Therefore, a lot of studies have proposed efficient
methods about the recognition algorithm using 2D camera captured
images. However, there is a limitation to these methods, such as the
extracted features cannot fully represent the object in real world.
Although many studies used 3D features instead of 2D features for
more accurate gesture recognition, the problem, such as the processing
time to generate 3D objects, is still unsolved in related researches.
Therefore we propose a method to extract the 3D features combined
with the 3D object reconstruction. This method uses the modified
GPU-based visual hull generation algorithm which disables unnecessary
processes, such as the texture calculation to generate three kinds
of 3D projection maps as the 3D feature: a nearest boundary, a farthest
boundary, and a thickness of the object projected on the base-plane. In
the section of experimental results, we present results of proposed
method on eight human postures: T shape, both hands up, right hand
up, left hand up, hands front, stand, sit and bend, and compare the
computational time of the proposed method with that of the previous
methods.
Abstract: Efficient handoff algorithms are a cost-effective way
of enhancing the capacity and QoS of cellular system. The higher
value of hysteresis effectively prevents unnecessary handoffs but
causes undesired cell dragging. This undesired cell dragging causes
interference or could lead to dropped calls in microcellular
environment. The problems are further exacerbated by the corner
effect phenomenon which causes the signal level to drop by 20-30 dB
in 10-20 meters. Thus, in order to maintain reliable communication
in a microcellular system new and better handoff algorithms must be
developed. A fuzzy based handoff algorithm is proposed in this paper
as a solution to this problem. Handoff on the basis of ratio of slopes
of normal signal loss to the actual signal loss is presented. The fuzzy
based solution is supported by comparing its results with the results
obtained in analytical solution.
Abstract: The design of a steam turbine is a very complex
engineering operation that can be simplified and improved thanks to
computer-aided multi-objective optimization. This process makes use
of existing optimization algorithms and losses correlations to identify
those geometries that deliver the best balance of performance (i.e.
Pareto-optimal points).
This paper deals with a one-dimensional multi-objective and
multi-point optimization of a single-stage steam turbine. Using a
genetic optimization algorithm and an algebraic one-dimensional
ideal gas-path model based on loss and deviation correlations, a code
capable of performing the optimization of a predefined steam turbine
stage was developed. More specifically, during this study the
parameters modified (i.e. decision variables) to identify the best
performing geometries were solidity and angles both for stator and
rotor cascades, while the objective functions to maximize were totalto-
static efficiency and specific work done.
Finally, an accurate analysis of the obtained results was carried
out.
Abstract: Overhead conveyor systems satisfy by their simple
construction, wide application range and their full compatibility with
other manufacturing systems, which are designed according to
international standards. Ultra-light overhead conveyor systems are
rope-based conveying systems with individually driven vehicles. The
vehicles can move automatically on the rope and this can be realized
by energy and signals. Crossings are realized by switches. Overhead
conveyor systems are particularly used in the automotive industry but
also at post offices. Overhead conveyor systems always must be
integrated with a logistical process by finding the best way for a
cheaper material flow and in order to guarantee precise and fast
workflows. With their help, any transport can take place without
wasting ground and space, without excessive company capacity, lost
or damaged products, erroneous delivery, endless travels and without
wasting time. Ultra-light overhead conveyor systems provide optimal
material flow, which produces profit and saves time. This article
illustrates the advantages of the structure of the ultra-light overhead
conveyor systems in logistics applications and explains the steps of
their system design. After an illustration of the steps, currently
available systems on the market will be shown by means of their
technical characteristics. Due to their simple construction, demands
to an ultra-light overhead conveyor system will be illustrated.
Abstract: Wind turbine should be controlled to capture maximum
wind energy and to prevent the turbine from being stalled. To achieve
those two goals, wind turbine controller controls torque on generator
and limits input torque from wind by pitching blade. Usually, torque
on generator is controlled using inverter torque set point. However,
verifying a control algorithm in actual wind turbine needs a lot of
efforts to test and the actual wind turbine could be broken while testing
a control algorithm. So, several software have developed and
commercialized by Garrad Hassan, GH Bladed, and NREL, FAST.
Even though, those programs can simulate control system modeling
with subroutines or DLLs. However, those simulation programs are
not able to emulate detailed generator or PMSG. In this paper, a small
size wind turbine simulator is developed with induction motor and
small size drive train. The developed system can simulate wind turbine
control algorithm in the region before rated power.