Abstract: An automatic speech recognition system for the
formal Arabic language is needed. The Quran is the most formal
spoken book in Arabic, it is spoken all over the world. In this
research, an automatic speech recognizer for Quranic based speakerindependent
was developed and tested. The system was developed
based on the tri-phone Hidden Markov Model and Maximum
Likelihood Linear Regression (MLLR). The MLLR computes a set
of transformations which reduces the mismatch between an initial
model set and the adaptation data. It uses the regression class tree, as
well as, estimates a set of linear transformations for the mean and
variance parameters of a Gaussian mixture HMM system. The 30th
Chapter of the Quran, with five of the most famous readers of the
Quran, was used for the training and testing of the data. The chapter
includes about 2000 distinct words. The advantages of using the
Quranic verses as the database in this developed recognizer are the
uniqueness of the words and the high level of orderliness between
verses. The level of accuracy from the tested data ranged 68 to 85%.
Abstract: The flow field over a three dimensional pole barn
characterized by a cylindrical roof has been numerically investigated.
Wind pressure and viscous loads acting on the agricultural building
have been analyzed for several incoming wind directions, so as to
evaluate the most critical load condition on the structure. A constant
wind velocity profile, based on the maximum reference wind speed in
the building site (peak gust speed worked out for 50 years return
period) and on the local roughness coefficient, has been simulated.
In order to contemplate also the hazard due to potential air
wedging between the stored hay and the lower part of the ceiling, the
effect of a partial filling of the barn has been investigated.
The distribution of wind-induced loads on the structure have been
determined, allowing a numerical quantification of the effect of wind
direction on the induced stresses acting on a hemicylindrical roof.
Abstract: This paper considers the development of a two-point
predictor-corrector block method for solving delay differential
equations. The formulae are represented in divided difference form
and the algorithm is implemented in variable stepsize variable order
technique. The block method produces two new values at a single
integration step. Numerical results are compared with existing
methods and it is evident that the block method performs very well.
Stability regions of the block method are also investigated.
Abstract: A concern that researchers usually face in different
applications of Artificial Neural Network (ANN) is determination of
the size of effective domain in time series. In this paper, trial and
error method was used on groundwater depth time series to determine
the size of effective domain in the series in an observation well in
Union County, New Jersey, U.S. different domains of 20, 40, 60, 80,
100, and 120 preceding day were examined and the 80 days was
considered as effective length of the domain. Data sets in different
domains were fed to a Feed Forward Back Propagation ANN with
one hidden layer and the groundwater depths were forecasted. Root
Mean Square Error (RMSE) and the correlation factor (R2) of
estimated and observed groundwater depths for all domains were
determined. In general, groundwater depth forecast improved, as
evidenced by lower RMSEs and higher R2s, when the domain length
increased from 20 to 120. However, 80 days was selected as the
effective domain because the improvement was less than 1% beyond
that. Forecasted ground water depths utilizing measured daily data
(set #1) and data averaged over the effective domain (set #2) were
compared. It was postulated that more accurate nature of measured
daily data was the reason for a better forecast with lower RMSE
(0.1027 m compared to 0.255 m) in set #1. However, the size of input
data in this set was 80 times the size of input data in set #2; a factor
that may increase the computational effort unpredictably. It was
concluded that 80 daily data may be successfully utilized to lower the
size of input data sets considerably, while maintaining the effective
information in the data set.
Abstract: The presence of toxic heavy metals in industrial
effluents is one of the serious threats to the environment. Heavy
metals such as Cadmium, Chromium, Lead, Nickel, Zinc, Mercury,
Copper, Arsenic are found in the effluents of industries such as
foundries, electroplating, petrochemical, battery manufacturing,
tanneries, fertilizer, dying, textiles, metallurgical and metal finishing.
Tremendous increase of industrial copper usage and its presence in
industrial effluents has lead to a growing concern about the fate and
effects of Copper in the environment. Percolation of industrial
effluents through soils leads to contamination of ground water and
soils. The transport of heavy metals and their diffusion into the soils
has therefore, drawn the attention of the researchers.
In this study, an attempt has been made to delineate the
mechanisms of transport and fate of copper in terrestrial
environment. Column studies were conducted using perplex glass
square column of dimension side 15 cm and 1.35 m long. The soil
samples were collected from a natural drain near Mohali (India). The
soil was characterized to be poorly graded sandy loam. The soil was
compacted to the field dry density level of about 1.6 g/cm3. Break
through curves for different depths of the column were plotted. The
results of the column study indicated that the copper has high
tendency to flow in the soils and fewer tendencies to get absorbed on
the soil particles. The t1/2 estimates obtained from the studies can be
used for design copper laden wastewater disposal systems.
Abstract: A novel circuit for generating a signal embedded with
features about data from three sensors is presented. This suggested
circuit is making use of a resistance-to-time converter employing a
bridge amplifier, an integrator and a comparator. The second resistive
sensor (Rz) is transformed into duty cycle. Another bridge with
varying resistor, (Ry) in the feedback of an OP AMP is added in
series to change the amplitude of the resulting signal in a proportional
relationship while keeping the same frequency and duty cycle
representing proportional changes in resistors Rx and Rz already
mentioned. The resultant output signal carries three types of
information embedded as variations of its frequency, duty cycle and
amplitude.
Abstract: This paper presents a NDT by infrared thermography with excitation CO2 Laser, wavelength of 10.6 μm. This excitation is the controllable heating beam, confirmed by a preliminary test on a wooden plate 1.2 m x 0.9 m x 1 cm. As the first practice, this method is applied to detecting the defect in CFRP heated by the Laser 300 W during 40 s. Two samples 40 cm x 40 cm x 4.5 cm are prepared, one with defect, another one without defect. The laser beam passes through the lens of a deviation device, and heats the samples placed at a determinate position and area. As a result, the absence of adhesive can be detected. This method displays prominently its application as NDT with the composite materials. This work gives a good perspective to characterize the laser beam, which is very useful for the next detection campaigns.
Abstract: The UML modeling of complex distributed systems often is a great challenge due to the large amount of parallel real-time operating components. In this paper the problems of verification of such systems are discussed. ECPN, an Extended Colored Petri Net is defined to formally describe state transitions of components and interactions among components. The relationship between sequence diagrams and Free Choice Petri Nets is investigated. Free Choice Petri Net theory helps verifying the liveness of sequence diagrams. By converting sequence diagrams to ECPNs and then comparing behaviors of sequence diagram ECPNs and statecharts, the consistency among models is analyzed. Finally, a verification process for an example model is demonstrated.
Abstract: This study investigated a strategy of blending lead-laden sludge and Al-rich precursors to reduce the release of metals from the stabilized products. Using PbO as the simulated lead-laden sludge to sinter with γ-Al2O3 by Pb:Al molar ratios of 1:2 and 1:12, PbAl2O4 and PbAl12O19 were formed as final products during the sintering process, respectively. By firing the PbO + γ-Al2O3 mixtures with different Pb/Al molar ratios at 600 to 1000 °C, the lead transformation was determined through X-ray diffraction (XRD) data. In Pb/Al molar ratio of 1/2 system, the formation of PbAl2O4 is initiated at 700 °C, but an effective formation was observed above 750 °C. An intermediate phase, Pb9Al8O21, was detected in the temperature range of 800-900 °C. However, different incorporation behavior for sintering PbO with Al-rich precursors at a Pb/Al molar ratio of 1/12 was observed during the formation of PbAl12O19 in this system. In the sintering process, both temperature and time effect on the formation of PbAl2O4 and PbAl12O19 phases were estimated. Finally, a prolonged leaching test modified from the U.S. Environmental Protection Agency-s toxicity characteristic leaching procedure (TCLP) was used to evaluate the durability of PbO, Pb9Al8O21, PbAl2O4 and PbAl12O19 phases. Comparison for the leaching results of the four phases demonstrated the higher intrinsic resistance of PbAl12O19 against acid attack.
Abstract: This paper presents the idea of a rough controller with application to control the overhead traveling crane system. The structure of such a controller is based on a suggested concept of a fuzzy logic controller. A measure of fuzziness in rough sets is introduced. A comparison between fuzzy logic controller and rough controller has been demonstrated. The results of a simulation comparing the performance of both controllers are shown. From these results we infer that the performance of the proposed rough controller is satisfactory.
Abstract: Future space vehicles will require the use of non-toxic, cryogenic propellants, because of the performance advantages over the toxic hypergolic propellants and also because of the environmental and handling concerns. A prototypical capillary flow liquid acquisition device (LAD) for cryogenic propellants was fabricated with a mesh screen, covering a rectangular flow channel with a cylindrical outlet tube, and was tested with liquid oxygen (LOX). In order to better understand the performance in various gravity environments and orientations with different submersion depths of the LAD, a series of computational fluid dynamics (CFD) simulations of LOX flow through the LAD screen channel, including horizontally and vertically submersions of the LAD channel assembly at normal gravity environment was conducted. Gravity effects on the flow field in LAD channel are inspected and analyzed through comparing the simulations.
Abstract: In this paper, in addition to introducing good urban planning and its effects on globalization, some new methodologies in urban management and another urban aspects has been presented. Some new concerns in increasing of urban population , metropolitans and its relations on big problems has been focused in this paper. It is very important matter that future urban planning with based on globalization will be with full of basically changes in its management and perspectives.
Abstract: The main objective of this project is to build an
autonomous microcontroller-based mobile robot for a local robot
soccer competition. The black competition field is equipped with
white lines to serve as the guidance path for competing robots. Two
prototypes of soccer robot embedded with the Basic Stamp II
microcontroller have been developed. Two servo motors are used as
the drive train for the first prototype whereas the second prototype
uses two DC motors as its drive train. To sense the lines, lightdependent
resistors (LDRs) supply the analog inputs for the
microcontroller. The performances of both prototypes are evaluated.
The DC motor-driven robot has produced better trajectory control
over the one using servo motors and has brought the team into the
final round.
Abstract: One of the most important requirements for the
operation and planning activities of an electrical utility is the
prediction of load for the next hour to several days out, known as
short term load forecasting. This paper presents the development of
an artificial neural network based short-term load forecasting model.
The model can forecast daily load profiles with a load time of one
day for next 24 hours. In this method can divide days of year with
using average temperature. Groups make according linearity rate of
curve. Ultimate forecast for each group obtain with considering
weekday and weekend. This paper investigates effects of temperature
and humidity on consuming curve. For forecasting load curve of
holidays at first forecast pick and valley and then the neural network
forecast is re-shaped with the new data. The ANN-based load models
are trained using hourly historical. Load data and daily historical
max/min temperature and humidity data. The results of testing the
system on data from Yazd utility are reported.
Abstract: As seen in literature, about 70% of the improvement initiatives fail, and a significant number do not even get started. This paper analyses the problem of failing initiatives on Software Process Improvement (SPI), and proposes good practices supported by motivational tools that can help minimizing failures. It elaborates on the hypothesis that human factors are poorly addressed by deployers, especially because implementation guides usually emphasize only technical factors. This research was conducted with SPI deployers and analyses 32 SPI initiatives. The results indicate that although human factors are not commonly highlighted in guidelines, the successful initiatives usually address human factors implicitly. This research shows that practices based on human factors indeed perform a crucial role on successful implantations of SPI, proposes change management as a theoretical framework to introduce those practices in the SPI context and suggests some motivational tools based on SPI deployers experience to support it.
Abstract: In this paper, a new approach for design of a fully
differential second order current mode continuous-time sigma-delta
modulator is presented. For circuit implementation, square root
domain (SRD) translinear loop based on floating-gate MOS
transistors that operate in saturation region is employed. The
modulator features, low supply voltage, low power consumption
(8mW) and high dynamic range (55dB). Simulation results confirm
that this design is suitable for data converters.
Abstract: Attitude control of aerospace system with liquid containers may face to a problem associate with fuel sloshing. The sloshing phenomena can degrade the stability of control system and in the worst case, interaction between the attitude control system and fuel vibration leading to resonance. In this paper, a full process of nonlinear dynamic modeling of an aerospace launch vehicle with fuel sloshing is given. Then, a new control system based on model reference adaptive filter is proposed and its algorithm is extracted. This controller implemented on the main attitude control system. Finally, numerical simulation of nonlinear model and control system is carried out to examine the performance of the new controller. Results of simulations show that the inconvenient effects of the fuel sloshing by augmenting this control system are reduced and attitude control system performs, satisfactorily.
Abstract: Simultaneous effects of temperature, immersion time, salt concentration, sucrose concentration, pressure and convective dryer temperature on the combined osmotic dehydration - convective drying of edible button mushrooms were investigated. Experiments were designed according to Central Composite Design with six factors each at five different levels. Response Surface Methodology (RSM) was used to determine the optimum processing conditions that yield maximum water loss and rehydration ratio and minimum solid gain and shrinkage in osmotic-convective drying of edible button mushrooms. Applying surfaces profiler and contour plots optimum operation conditions were found to be temperature of 39 °C, immersion time of 164 min, salt concentration of 14%, sucrose concentration of 53%, pressure of 600 mbar and drying temperature of 40 °C. At these optimum conditions, water loss, solid gain, rehydration ratio and shrinkage were found to be 63.38 (g/100 g initial sample), 3.17 (g/100 g initial sample), 2.26 and 7.15%, respectively.
Abstract: The new technology of fuzzy neural networks for identification of parameters for mathematical models of geofields is proposed and checked. The effectiveness of that soft computing technology is demonstrated, especially in the early stage of modeling, when the information is uncertain and limited.
Abstract: Article devoted to the development of technologies
for medicine and agroecology by using plant organelle – spherosome.
Technological method of purification and isolation of this organelle
by using novel nanostructured carbon sorbent – “nanocarbosorb"
ARK type are presented. Also the methods of preparation of
nanocontainers based on using of spherosome with loaded isosorbide
dinitrate, piroxicam or diclofenak are exhibited. We found that the
spherosome could be applied for ecological aims as bioregulator and
also as biosensor for determination of ammonia ions in water
reservoirs at concentration range 1mM to 100mM.