Abstract: The study of the geometric shape of the plunging wave enclosed vortices as a possible indicator for the breaking intensity of ocean waves has been ongoing for almost 50 years with limited success. This paper investigates the validity of using the vortex ratio and vortex angle as methods of predicting breaking intensity. Previously published works on vortex parameters, based on regular wave flume results or solitary wave theory, present contradictory results and conclusions. Through the first complete analysis of field collected irregular wave breaking vortex parameters it is illustrated that the vortex ratio and vortex angle cannot be accurately predicted using standard breaking wave characteristics and hence are not suggested as a possible indicator for breaking intensity.
Abstract: Software reliability prediction gives a great opportunity to measure the software failure rate at any point throughout system test. A software reliability prediction model provides with the technique for improving reliability. Software reliability is very important factor for estimating overall system reliability, which depends on the individual component reliabilities. It differs from hardware reliability in that it reflects the design perfection. Main reason of software reliability problems is high complexity of software. Various approaches can be used to improve the reliability of software. We focus on software reliability model in this article, assuming that there is a time redundancy, the value of which (the number of repeated transmission of basic blocks) can be an optimization parameter. We consider given mathematical model in the assumption that in the system may occur not only irreversible failures, but also a failure that can be taken as self-repairing failures that significantly affect the reliability and accuracy of information transfer. Main task of the given paper is to find a time distribution function (DF) of instructions sequence transmission, which consists of random number of basic blocks. We consider the system software unreliable; the time between adjacent failures has exponential distribution.
Abstract: The world economic crises and budget constraints
have caused authorities, especially those in developing countries, to
rationalize water quality monitoring activities. Rationalization
consists of reducing the number of monitoring sites, the number of
samples, and/or the number of water quality variables measured. The
reduction in water quality variables is usually based on correlation. If
two variables exhibit high correlation, it is an indication that some of
the information produced may be redundant. Consequently, one
variable can be discontinued, and the other continues to be measured.
Later, the ordinary least squares (OLS) regression technique is
employed to reconstitute information about discontinued variable by
using the continuously measured one as an explanatory variable. In
this paper, two record extension techniques are employed to
reconstitute information about discontinued water quality variables,
the OLS and the Line of Organic Correlation (LOC). An empirical
experiment is conducted using water quality records from the Nile
Delta water quality monitoring network in Egypt. The record
extension techniques are compared for their ability to predict
different statistical parameters of the discontinued variables. Results
show that the OLS is better at estimating individual water quality
records. However, results indicate an underestimation of the variance
in the extended records. The LOC technique is superior in preserving
characteristics of the entire distribution and avoids underestimation
of the variance. It is concluded from this study that the OLS can be
used for the substitution of missing values, while LOC is preferable
for inferring statements about the probability distribution.
Abstract: Electrical Discharge Machine (EDM) is especially
used for the manufacturing of 3-D complex geometry and hard
material parts that are extremely difficult-to-machine by conventional
machining processes. In this paper authors review the research work
carried out in the development of die-sinking EDM within the past
decades for the improvement of machining characteristics such as
Material Removal Rate, Surface Roughness and Tool Wear Ratio. In
this review various techniques reported by EDM researchers for
improving the machining characteristics have been categorized as
process parameters optimization, multi spark technique, powder
mixed EDM, servo control system and pulse discriminating. At the
end, flexible machine controller is suggested for Die Sinking EDM to
enhance the machining characteristics and to achieve high-level
automation. Thus, die sinking EDM can be integrated with Computer
Integrated Manufacturing environment as a need of agile
manufacturing systems.
Abstract: Machining through turning was carried out in a lathe
to study the chip formation of Multiphase Ferrite
(F-B-M) microalloyed steel. Taguchi orthogonal array was employed
to perform the machining. Continuous and discontinuous chips were
formed for different cutting parameters like speed, feed and depth of
cut. Optical and scanning electron microscope was employed to
identify the chip morphology.
Abstract: The incidence of mechanical fracture of an
automobile piston rings prompted development of fracture analysis
method on this case. The three rings (two compression rings and one
oil ring) were smashed into several parts during the power-test (after
manufacturing the engine) causing piston and liner to be damaged.
The radial and oblique cracking happened on the failed piston rings.
The aim of the fracture mechanics simulations presented in this paper
was the calculation of particular effective fracture mechanics
parameters, such as J-integrals and stress intensity factors. Crack
propagation angles were calculated as well. Two-dimensional
fracture analysis of the first compression ring has been developed in
this paper using ABAQUS CAE6.5-1 software. Moreover, SEM
fractography was developed on fracture surfaces and is discussed in
this paper. Results of numerical calculations constitute the basis for
further research on real object.
Abstract: with increasing circuits- complexity and demand to
use portable devices, power consumption is one of the most
important parameters these days. Full adders are the basic block of
many circuits. Therefore reducing power consumption in full adders
is very important in low power circuits. One of the most powerconsuming
modules in full adders is XOR/XNOR circuit. This paper
presents two new full adders based on two new logic approaches. The
proposed logic approaches use one XOR or XNOR gate to implement
a full adder cell. Therefore, delay and power will be decreased. Using
two new approaches and two XOR and XNOR gates, two new full
adders have been implemented in this paper. Simulations are carried
out by HSPICE in 0.18μm bulk technology with 1.8V supply voltage.
The results show that the ten-transistors proposed full adder has 12%
less power consumption and is 5% faster in comparison to MB12T
full adder. 9T is more efficient in area and is 24% better than similar
10T full adder in term of power consumption. The main drawback of
the proposed circuits is output threshold loss problem.
Abstract: This paper presents a model for the evaluation of
energy performance and aerodynamic forces acting on a three-bladed
small vertical axis Darrieus wind turbine depending on blade chord
curvature with respect to rotor axis.
The adopted survey methodology is based on an analytical code
coupled to a solid modeling software, capable of generating the
desired blade geometry depending on the blade design geometric
parameters, which is linked to a finite volume CFD code for the
calculation of rotor performance.
After describing and validating the model with experimental data,
the results of numerical simulations are proposed on the bases of two
different blade profile architectures, which are respectively
characterized by a straight chord and by a curved one, having a chord
radius equal to rotor external circumference. A CFD campaign of
analysis is completed for three blade-candidate airfoil sections, that is
the recently-developed DU 06-W-200 cambered blade profile, a
classical symmetrical NACA 0021 and its derived cambered airfoil,
characterized by a curved chord, having a chord radius equal to rotor
external circumference.
The effects of blade chord curvature on angle of attack, blade
tangential and normal forces are first investigated and then the
overall rotor torque and power are analyzed as a function of blade
azimuthal position, achieving a numerical quantification of the
influence of blade camber on overall rotor performance.
Abstract: Eutrophication of surface water is one of the most
widespread environmental problems at present. Large number of
pilgrims and tourists visit sacred artificial tank known as “Brahma
Sarover” located at Kurukshetra, India to take holy dip and perform
religious ceremonies. The sources of pollutants include impurities in
feed water, mass bathing, religious offerings and windblown
particulate matter. Studies so far have focused mainly on assessing
water quality for bathing purpose by using physico-chemical and
bacteriological parameters. No effort has been made to assess nutrient
concentration and trophic status of the tank to take more appropriate
measures for improving water quality on long term basis. In the
present study, total nitrogen, total phosphorous and chlorophyll a
measurements have been done to assess the nutrient level and trophic
status of the tank. The results show presence of high concentration of
nutrients and Chlorophyll a indicating mesotrophic and eutrophic
state of the tank. Phosphorous has been observed as limiting nutrient
in the tank water.
Abstract: There are lots of different ways to find the natural
frequencies of a rotating system. One of the most effective methods
which is used because of its precision and correctness is the
application of the transfer matrix. By use of this method the entire
continuous system is subdivided and the corresponding differential
equation can be stated in matrix form. So to analyze shaft that is this
paper issue the rotor is divided as several elements along the shaft
which each one has its own mass and moment of inertia, which this
work would create possibility of defining the named matrix. By
Choosing more elements number, the size of matrix would become
larger and as a result more accurate answers would be earned. In this
paper the dynamics of a rotor-bearing system is analyzed,
considering the gyroscopic effect. To increase the accuracy of
modeling the thickness of the disk and bearings is also taken into
account which would cause more complicated matrix to be solved.
Entering these parameters to our modeling would change the results
completely that these differences are shown in the results. As said
upper, to define transfer matrix to reach the natural frequencies of
probed system, introducing some elements would be one of the
requirements. For the boundary condition of these elements, bearings
at the end of the shaft are modeled as equivalent spring and dampers
for the discretized system. Also, continuous model is used for the
shaft in the system. By above considerations and using transfer
matrix, exact results are taken from the calculations. Results Show
that, by increasing thickness of the bearing the amplitude of vibration
would decrease, but obviously the stiffness of the shaft and the
natural frequencies of the system would accompany growth.
Consequently it is easily understood that ignoring the influences of
bearing and disk thicknesses would results not real answers.
Abstract: Groundlessness of application probability-statistic methods are especially shown at an early stage of the aviation GTE technical condition diagnosing, when the volume of the information has property of the fuzzy, limitations, uncertainty and efficiency of application of new technology Soft computing at these diagnosing stages by using the fuzzy logic and neural networks methods. It is made training with high accuracy of multiple linear and nonlinear models (the regression equations) received on the statistical fuzzy data basis. At the information sufficiency it is offered to use recurrent algorithm of aviation GTE technical condition identification on measurements of input and output parameters of the multiple linear and nonlinear generalized models at presence of noise measured (the new recursive least squares method (LSM)). As application of the given technique the estimation of the new operating aviation engine D30KU-154 technical condition at height H=10600 m was made.
Abstract: Drilling of glass sheets with different thicknesses have
been carried out by Abrasive Jet Machining process (AJM) in order
to determine its machinability under different controlling parameters
of the AJM process. The present study has been introduced a
mathematical model and the obtained results have been compared
with that obtained from other models published earlier [1-6]. The
experimental results of the present work are used to discuss the
validity of the proposed model as well as the other models.
Abstract: The aim of this research was to calculate the thermal
properties of Au3Ni Nanowire. The molecular dynamics (MD)
simulation technique was used to obtain the effect of radius size on
the energy, the melting temperature and the latent heat of fusion at
the isobaric-isothermal (NPT) ensemble. The Quantum Sutton-Chen
(Q-SC) many body interatomic potentials energy have been used for
Gold (Au) and Nickel (Ni) elements and a mixing rule has been
devised to obtain the parameters of these potentials for nanowire
stats. Our MD simulation results show the melting temperature and
latent heat of fusion increase upon increasing diameter of nanowire.
Moreover, the cohesive energy decreased with increasing diameter of
nanowire.
Abstract: In this paper fatigue crack growth behavior of
aeronautical aluminum alloy 2024 T351 was studied. Effects of
various loading and geometrical parameters are studied such as stress
ratio, amplitude loading, etc. The fatigue crack growth with constant
amplitude is studied using the AFGROW code when NASGRO
model is used. The effect of the stress ratio is highlighted, where one
notices a shift of the curves of crack growth. The comparative study
between two orientations L-T and T-L on fatigue behavior are
presented and shows the variation on the fatigue life. L-T orientation
presents a good fatigue crack growth resistance. Effects of crack
closure are shown in Paris domain and that no crack closure
phenomenons are present at high stress intensity factor.
Abstract: For over a decade, the Pulse Coupled Neural Network
(PCNN) based algorithms have been successfully used in image
interpretation applications including image segmentation. There are
several versions of the PCNN based image segmentation methods,
and the segmentation accuracy of all of them is very sensitive to the
values of the network parameters. Most methods treat PCNN
parameters like linking coefficient and primary firing threshold as
global parameters, and determine them by trial-and-error. The
automatic determination of appropriate values for linking coefficient,
and primary firing threshold is a challenging problem and deserves
further research. This paper presents a method for obtaining global as
well as local values for the linking coefficient and the primary firing
threshold for neurons directly from the image statistics. Extensive
simulation results show that the proposed approach achieves
excellent segmentation accuracy comparable to the best accuracy
obtainable by trial-and-error for a variety of images.
Abstract: One of the main research directions in CAD/CAM
machining area is the reducing of machining time.
The feedrate scheduling is one of the advanced techniques that
allows keeping constant the uncut chip area and as sequel to keep
constant the main cutting force. They are two main ways for feedrate
optimization. The first consists in the cutting force monitoring, which
presumes to use complex equipment for the force measurement and
after this, to set the feedrate regarding the cutting force variation. The
second way is to optimize the feedrate by keeping constant the
material removal rate regarding the cutting conditions.
In this paper there is proposed a new approach using an extended
database that replaces the system model.
The feedrate scheduling is determined based on the identification
of the reconfigurable machine tool, and the feed value determination
regarding the uncut chip section area, the contact length between tool
and blank and also regarding the geometrical roughness.
The first stage consists in the blank and tool monitoring for the
determination of actual profiles. The next stage is the determination
of programmed tool path that allows obtaining the piece target
profile.
The graphic representation environment models the tool and blank
regions and, after this, the tool model is positioned regarding the
blank model according to the programmed tool path. For each of
these positions the geometrical roughness value, the uncut chip area
and the contact length between tool and blank are calculated. Each of
these parameters are compared with the admissible values and
according to the result the feed value is established.
We can consider that this approach has the following advantages:
in case of complex cutting processes the prediction of cutting force is
possible; there is considered the real cutting profile which has
deviations from the theoretical profile; the blank-tool contact length
limitation is possible; it is possible to correct the programmed tool
path so that the target profile can be obtained.
Applying this method, there are obtained data sets which allow the
feedrate scheduling so that the uncut chip area is constant and, as a
result, the cutting force is constant, which allows to use more
efficiently the machine tool and to obtain the reduction of machining
time.
Abstract: The aim of this research is to evaluate surface
roughness and develop a multiple regression model for surface roughness as a function of cutting parameters during the turning of
flame hardened medium carbon steel with TiN-Al2O3-TiCN coated inserts. An experimental plan of work and signal-to-noise ratio (S/N)
were used to relate the influence of turning parameters to the
workpiece surface finish utilizing Taguchi methodology. The effects
of turning parameters were studied by using the analysis of variance (ANOVA) method. Evaluated parameters were feed, cutting speed,
and depth of cut. It was found that the most significant interaction among the considered turning parameters was between depth of cut and feed. The average surface roughness (Ra) resulted by TiN-Al2O3-
TiCN coated inserts was about 2.44 μm and minimum value was 0.74 μm. In addition, the regression model was able to predict values for surface roughness in comparison with experimental values within
reasonable limit.
Abstract: The amplitude response of infrared (IR) sensors
depends on the reflectance properties of the target. Therefore, in
order to use IR sensor for measuring distances accurately, prior
knowledge of the surface must be known. This paper describes the
Phong Illumination Model for determining the properties of a surface
and subsequently calculating the distance to the surface. The angular
position of the IR sensor is computed as normal to the surface for
simplifying the calculation. Ultrasonic (US) sensor can provide the
initial information on distance to obtain the parameters for this
method. In addition, the experimental results obtained by using
LabView are discussed. More care should be taken when placing the
objects from the sensors during acquiring data since the small change
in angle could show very different distance than the actual one.
Since stereo camera vision systems do not perform well under some
environmental conditions such as plain wall, glass surfaces, or poor
lighting conditions, the IR and US sensors can be used additionally to
improve the overall vision systems of mobile robots.
Abstract: In this paper, RSA encryption algorithm and its hardware
implementation in Xilinx-s Virtex Field Programmable Gate
Arrays (FPGA) is analyzed. The issues of scalability, flexible performance,
and silicon efficiency for the hardware acceleration of
public key crypto systems are being explored in the present work.
Using techniques based on the interleaved math for exponentiation,
the proposed RSA calculation architecture is compared to existing
FPGA-based solutions for speed, FPGA utilization, and scalability.
The paper covers the RSA encryption algorithm, interleaved multiplication,
Miller Rabin algorithm for primality test, extended Euclidean
math, basic FPGA technology, and the implementation details of
the proposed RSA calculation architecture. Performance of several
alternative hardware architectures is discussed and compared. Finally,
conclusion is drawn, highlighting the advantages of a fully flexible
& parameterized design.
Abstract: Abrasive Jet Machining is an Unconventional
machining process in which the metal is removed from brittle and
hard material in the form of micro-chips. With increase in need of
materials like ceramics, composites, in manufacturing of various
Mechanical & Electronic components, AJM has become a useful
technique for micro machining. The present study highlights the
influence of different parameters like Pressure, SOD, Time, Abrasive
grain size, nozzle diameter on the Metal removal of FRP (Fiber
Reinforced Polymer) composite by Abrasive jet machining. The
results of the Experiments conducted were analyzed and optimized
with TAGUCHI method of Optimization and ANOVA for Optimal
Value.