Abstract: A numerical study of flow in a horizontally channel
partially filled with a porous screen with non-uniform inlet has been
performed by lattice Boltzmann method (LBM). The flow in porous
layer has been simulated by the Brinkman-Forchheimer model.
Numerical solutions have been obtained for variable porosity models
and the effects of Darcy number and porosity have been studied in
detail. It is found that the flow stabilization is reliant on the Darcy
number. Also the results show that the stabilization of flow field and
heat transfer is depended to Darcy number. Distribution of stream
field becomes more stable by decreasing Darcy number. Results
illustrate that the effect of variable porosity is significant just in the
region of the solid boundary. In addition, difference between constant
and variable porosity models is decreased by decreasing the Darcy
number.
Abstract: Electro-hydraulic power steering (EHPS) system for
the fuel rate reduction and steering feel improvement is comprised of
ECU including the logic which controls the steering system and BL
DC motor and produces the best suited cornering force, BLDC motor,
high pressure pump integrated module and basic oil-hydraulic circuit
of the commercial HPS system.
Electro-hydraulic system can be studied in two ways such as
experimental and computer simulation. To get accurate results in
experimental study of EHPS system, the real boundary management is
necessary which is difficult task. And the accuracy of the experimental
results depends on the preparation of the experimental setup and
accuracy of the data collection. The computer simulation gives
accurate and reliable results if the simulation is carried out considering
proper boundary conditions. So, in this paper, each component of
EHPS was modeled, and the model-based analysis and control logic
was designed by using AMESim
Abstract: Alkali Activated Slag Concrete (AASC) mixes are manufactured by activating ground granulated blast furnace slag (GGBFS) using sodium hydroxide and sodium silicate solutions. The aim of the present experimental research was to investigate the effect of increasing the dosages of sodium oxide (Na2O, in the range of 4 to 8%) and the activator modulus (Ms) (i.e. the SiO2/Na2O ratio, in the range of 0.5 to 1.5) of the alkaline solutions, on the workability and strength characteristics of self-cured (air-cured) alkali activated Indian slag concrete mixes. Further the split tensile and flexure strengths for optimal mixes were studied for each dosage of Na2O.It is observed that increase in Na2O concentration increases the compressive, split-tensile and flexural strengths, both at the early and later-ages, while increase in Ms, decreases the workability of the mixes. An optimal Ms of 1.25 is found at various Na2O dosages. No significant differences in the strength performances were observed between AASCs manufactured with alkali solutions prepared using either of potable and de-ionized water.
Abstract: The influence of lactulose and inulin on rheological
properties of fermented milk during storage was studied.Pasteurized
milk, freeze-dried starter culture Bb-12 (Bifidobacterium lactis, Chr.
Hansen, Denmark), inulin – RAFTILINE®HP (ORAFI, Belgium) and
syrup of lactulose (Duphalac®, the Netherlands) were used for
experiments. The fermentation process was realized at 37 oC for 16
hours and the storage of products was provided at 4 oC for 7 days.
Measurements were carried out by BROOKFIELD standard methods
and the flow curves were described by Herschel-Bulkley model.
The results of dispersion analysis have shown that both the
concentration of prebiotics (p=0.04
Abstract: Optimum communication and performance in
Wireless Sensor Networks, constitute multi-facet challenges due to
the specific networking characteristics as well as the scarce resource
availability. Furthermore, it is becoming increasingly apparent that
isolated layer based approaches often do not meet the demands posed
by WSNs applications due to omission of critical inter-layer
interactions and dependencies. As a counterpart, cross-layer is
receiving high interest aiming to exploit these interactions and
increase network performance. However, in order to clearly identify
existing dependencies, comprehensive performance studies are
required evaluating the effect of different critical network parameters
on system level performance and behavior.This paper-s main
objective is to address the need for multi-parametric performance
evaluations considering critical network parameters using a well
known network simulator, offering useful and practical conclusions
and guidelines. The results reveal strong dependencies among
considered parameters which can be utilized by and drive future
research efforts, towards designing and implementing highly efficient
protocols and architectures.
Abstract: A registration framework for image-guided robotic
surgery is proposed for three emergency neurosurgical procedures,
namely Intracranial Pressure (ICP) Monitoring, External Ventricular
Drainage (EVD) and evacuation of a Chronic Subdural Haematoma
(CSDH). The registration paradigm uses CT and white light as
modalities. This paper presents two simulation studies for a
preliminary evaluation of the registration protocol: (1) The loci of the
Target Registration Error (TRE) in the patient-s axial, coronal and
sagittal views were simulated based on a Fiducial Localisation Error
(FLE) of 5 mm and (2) Simulation of the actual framework using
projected views from a surface rendered CT model to represent white
light images of the patient. Craniofacial features were employed as
the registration basis to map the CT space onto the simulated
intraoperative space. Photogrammetry experiments on an artificial
skull were also performed to benchmark the results obtained from the
second simulation. The results of both simulations show that the
proposed protocol can provide a 5mm accuracy for these
neurosurgical procedures.
Abstract: DC-DC converters are widely used in regulated switched mode power supplies and in DC motor drive applications. There are several sources of unwanted nonlinearity in practical power converters. In addition, their operation is characterized by switching that gives birth to a variety of nonlinear dynamics. DC-DC buck and boost converters controlled by pulse-width modulation (PWM) have been simulated. The voltage waveforms and attractors obtained from the circuit simulation have been studied. With the onset of instability, the phenomenon of subharmonic oscillations, quasi-periodicity, bifurcations, and chaos have been observed. This paper is mainly motivated by potential contributions of chaos theory in the design, analysis and control of power converters, in particular and power electronics circuits, in general.
Abstract: An experimental study of Reinforced Concrete, RC, columns strengthened using a steel jacketing technique was conducted. The jacketing technique consisted of four steel vertical angles installed at the corners of the column joined by horizontal steel straps confining the column externally. The effectiveness of the technique was evaluated by testing the RC column specimens under eccentric monotonic loading until failure occurred. Strain gauges were installed to monitor the strains in the internal reinforcement as well as the external jacketing system. The effectiveness of the jacketing technique was demonstrated, and the parameters affecting the technique were studied.
Abstract: This paper addresses the problem of asymptotic tracking
control of a linear parabolic partial differential equation with indomain
point actuation. As the considered model is a non-standard
partial differential equation, we firstly developed a map that allows
transforming this problem into a standard boundary control problem
to which existing infinite-dimensional system control methods can
be applied. Then, a combination of energy multiplier and differential
flatness methods is used to design an asymptotic tracking controller.
This control scheme consists of stabilizing state-feedback derived
from the energy multiplier method and feed-forward control based
on the flatness property of the system. This approach represents
a systematic procedure to design tracking control laws for a class
of partial differential equations with in-domain point actuation. The
applicability and system performance are assessed by simulation
studies.
Abstract: A total of twenty tensile biopsies were collected from
children undergoing tonsillectomy from teaching hospital ENT
department and Kurdistan private hospital in sulaimani city. All
biopsies were homogenized and cultured; the obtained bacterial
isolates were purified and identified by biochemical tests and VITEK
2 compact system. Among the twenty studied samples, only one
Pseudomonas putida with probability of 99% was isolated.
Antimicrobial susceptibility was carried out by disk diffusion
method, Pseudomonas putida showed resistance to all antibiotics
used except vancomycin. The isolate further subjected to PCR and
DNA sequence analysis of blaVIM gene using different set of primers
for different regions of VIM gene. The results were found to be PCR
positive for the blaVIM gene. To determine the sequence of blaVIM
gene, DNA sequencing performed. Sequence alignment of blaVIM
gene with previously recorded blaVIM gene in NCBI- database showed
that P. putida isolate have different blaVIM gene.
Abstract: Recent financial international scandals around the world have led to a number of investigations into the effectiveness of corporate governance practices and audit quality. Although evidence of corporate governance practices and audit quality exists from developed economies, very scanty studies have been conducted in Egypt where corporate governance is just evolving. Therefore, this study provides evidence on the effectiveness of corporate governance practices and audit quality from a developing country. The data for analysis are gathered from the top 50 most active companies in the Egyptian Stock Exchange, covering the three year period 2007-2009. Logistic regression was used in investigating the questions that were raised in the study. Findings from the study show that board independence; CEO duality and audit committees significantly have relationship with audit quality. The results also, indicate that institutional investor and managerial ownership have no significantly relationship with audit quality. Evidence also exist that size of the company; complexity and business leverage are important factors in audit quality for companies quoted on the Egypt Stock Exchange.
Abstract: The effect of different combinations of response
feedback on the performance of active control system on nonlinear
frames has been studied in this paper. To this end different feedback
combinations including displacement, velocity, acceleration and full
response feedback have been utilized in controlling the response of
an eight story bilinear hysteretic frame which has been subjected to a
white noise excitation and controlled by eight actuators which could
fully control the frame. For active control of nonlinear frame
Newmark nonlinear instantaneous optimal control algorithm has been
used which a diagonal matrix has been selected for weighting
matrices in performance index. For optimal design of active control
system while the objective has been to reduce the maximum drift to
below the yielding level, Distributed Genetic Algorithm (DGA) has
been used to determine the proper set of weighting matrices. The
criteria to assess the effect of each combination of response feedback
have been the minimum required control force to reduce the
maximum drift to below the yielding drift. The results of numerical
simulation show that the performance of active control system is
dependent on the type of response feedback where the velocity
feedback is more effective in designing optimal control system in
comparison with displacement and acceleration feedback. Also using
full feedback of response in controller design leads to minimum
control force amongst other combinations. Also the distributed
genetic algorithm shows acceptable convergence speed in solving the
optimization problem of designing active control systems.
Abstract: To investigate the behavior of sheet metals during
forming tailor welded blanks (TWB) of various thickness made via
Co2 Laser welding are under consideration. These blanks are formed
used two different forming methods of rubber as well as the
conventional punch and die methods. The main research objective is
the effects of using a rubber die instead of a solid one the
displacement of the weld line and the press force needed for forming.
Specimens with thicknesses of 0.5, 0.6, 0.8 and 1mm are subjected to
Erichsen two dimensional tests and the resulted force for each case
are compared. This is followed by a theoretical and numerical study
of press force and weld line displacement. It is concluded that using
rubber pad forming (RPF) causes a reduction in weld line
displacement and an increase in the press force.
Abstract: Application of neural networks in execution of
programmed pulse width modulation (PPWM) of a voltage source
inverter (VSI) is studied in this paper. Using the proposed method it is
possible to cancel out the desired harmonics in output of VSI in
addition to control the magnitude of fundamental harmonic,
contineously. By checking the non-trained values and a performance
index, the most appropriate neural network is proposed. It is shown
that neural networks may solve the custom difficulties of practical
utilization of PPWM such as large size of memory, complex digital
circuits and controlling the magnitude of output voltage in a discrete
manner.
Abstract: Most fingerprint recognition techniques are based on minutiae matching and have been well studied. However, this technology still suffers from problems associated with the handling of poor quality impressions. One problem besetting fingerprint matching is distortion. Distortion changes both geometric position and orientation, and leads to difficulties in establishing a match among multiple impressions acquired from the same finger tip. Marking all the minutiae accurately as well as rejecting false minutiae is another issue still under research. Our work has combined many methods to build a minutia extractor and a minutia matcher. The combination of multiple methods comes from a wide investigation into research papers. Also some novel changes like segmentation using Morphological operations, improved thinning, false minutiae removal methods, minutia marking with special considering the triple branch counting, minutia unification by decomposing a branch into three terminations, and matching in the unified x-y coordinate system after a two-step transformation are used in the work.
Abstract: Control of commutation of switched reluctance (SR)
motor has been an area of interest for researchers for sometime now
with mixed successes in addressing the inherent challenges. New
technologies, processing schemes and methods have been adopted to
make sensorless SR drive a reality. There are a number of
conceptual, offline, analytical and online solutions in literature that
have varying complexities and achieved equally varying degree of
robustness and accuracies depending on the method used to address
the challenges and the SR drive application. Magnetic coupling is
one such challenge when using active probing techniques to
determine rotor position of a SR motor from stator winding. This
paper studies the effect of back-of-core saturation on the detected
rotor position and presents results on measurement made on a 4-
phase SR motor. The results shows that even for a four phase motor
which is excited one phase at a time and using the electrically
opposite phase for active position probing, the back-of-core
saturation effects should not be ignored.
Abstract: Thermally insulating ceramic coatings also known as
thermal barrier coatings (TBCs) have been essential technologies to
improve the performance and efficiency of advanced gas turbines in
service at extremely high temperatures. The damage mechanisms of
air-plasma sprayed YSZ thermal barrier coatings (TBC) with various
microstructures were studied by microscopic techniques after thermal
cycling. The typical degradation of plasma TBCs that occurs during
cyclic furnace testing of an YSZ and alumina coating on a Titanium
alloy are analyzed. During the present investigation the effects of
topcoat thickness, bond coat oxidation, thermal cycle lengths and test
temperature are investigated using thermal cycling. These results
were correlated with stresses measured by a spectroscopic technique
in order to understand specific damage mechanism. The failure
mechanism of former bond coats was found to involve fracture
initiation at the thermally grown oxide (TGO) interface and at the
TGO bond coat interface. The failure mechanism of the YZ was
found to involve combination of fracture along the interface between
TGO and bond coat.
Abstract: In this project cadmium ions were adsorbed from
aqueous solutions onto either date pits; a cheap agricultural and nontoxic
material, or chemically activated carbon prepared from date pits
using phosphoric acid. A series of experiments were conducted in a
batch adsorption technique to assess the feasibility of using the
prepared adsorbents. The effects of the process variables such as
initial cadmium ions concentration, contact time, solution pH and
adsorbent dose on the adsorption capacity of both adsorbents were
studied. The experimental data were tested using different isotherm
models such as Langmuir, Freundlich, Tempkin and Dubinin-
Radushkevich. The results showed that although the equilibrium data
could be described by all models used, Langmuir model gave slightly
better results when using activated carbon while Freundlich model,
gave better results with date pits.
Abstract: Most of the drugs used for pharmaceutical purposes
are poorly water-soluble drugs. About 40% of all newly discovered
drugs are lipophilic and the numbers of lipophilic drugs seem to
increase more and more. Drug delivery systems such as
nanoparticles, micelles or liposomes are applied to improve their
solubility and thus their bioavailability. Besides various techniques of
solubilization, oil-in-water emulsions are often used to incorporate
lipophilic drugs into the oil phase. To stabilize emulsions surface
active substances (surfactants) are generally used. An alternative
method to avoid the application of surfactants was of great interest.
One possibility is to develop O/W-emulsion without any addition of
surface active agents or the so called “surfactant-free emulsion or
SFE”. The aim of this study was to develop and characterize SFE as a
drug carrier by varying the production conditions. Lidocaine base
was used as a model drug. The injection method was developed.
Effects of ultrasound as well as of temperature on the properties of
the emulsion were studied. Particle sizes and release were
determined. The long-term stability up to 30 days was performed.
The results showed that the surfactant-free O/W emulsions with
pharmaceutical oil as drug carrier can be produced.
Abstract: Polyphenolics and sugar are the components of many
fruit juices. In this work, the performance of ultra-filtration (UF) for
separating phenolic compounds from apple juice was studied by
performing batch experiments in a membrane module with an area of
0.1 m2 and fitted with a regenerated cellulose membrane of 1 kDa
MWCO. The effects of various operating conditions: transmembrane
pressure (3, 4, 5 bar), temperature (30, 35, 40 ºC), pH (2, 3, 4, 5),
feed concentration (3, 5, 7, 10, 15 ºBrix for apple juice) and feed flow
rate (1, 1.5, 1.8 L/min) on the performance were determined.
The optimum operating conditions were: transmembrane pressure
4 bar, temperature 30 ºC, feed flow rate 1 – 1.8 L/min, pH 3 and 10
Brix (apple juice). After performing ultrafiltration under these
conditions, the concentration of polyphenolics in retentate was
increased by a factor of up to 2.7 with up to 70% recovered in the
permeate and with approx. 20% of the sugar in that stream..
Application of diafiltration (addition of water to the concentrate) can
regain the flux by a factor of 1.5, which has been decreased due to
fouling. The material balance performed on the process has shown
the amount of deposits on the membrane and the extent of fouling in
the system. In conclusion, ultrafiltration has been demonstrated as a
potential technology to separate the polyphenolics and sugars from
their mixtures and can be applied to remove sugars from fruit juice.