Abstract: Many advanced Routing protocols for wireless sensor networks have been implemented for the effective routing of data. Energy awareness is an essential design issue and almost all of these routing protocols are considered as energy efficient and its ultimate objective is to maximize the whole network lifetime. However, the introductions of video and imaging sensors have posed additional challenges. Transmission of video and imaging data requires both energy and QoS aware routing in order to ensure efficient usage of the sensors and effective access to the gathered measurements. In this paper, the performance of the energy-aware QoS routing Protocol are analyzed in different performance metrics like average lifetime of a node, average delay per packet and network throughput. The parameters considered in this study are end-to-end delay, real time data generation/capture rates, packet drop probability and buffer size. The network throughput for realtime and non-realtime data was also has been analyzed. The simulation has been done in NS2 simulation environment and the simulation results were analyzed with respect to different metrics.
Abstract: Multicarrier transmission system such as Orthogonal
Frequency Division Multiplexing (OFDM) is a promising technique
for high bit rate transmission in wireless communication systems.
OFDM is a spectrally efficient modulation technique that can achieve
high speed data transmission over multipath fading channels without
the need for powerful equalization techniques. A major drawback
of OFDM is the high Peak-to-Average Power Ratio (PAPR) of the
transmit signal which can significantly impact the performance of the
power amplifier. In this paper we have compared the PAPR reduction
performance of Golay and Reed-Muller coded OFDM signal. From
our simulation it has been found that the PAPR reduction performance
of Golay coded OFDM is better than the Reed-Muller coded OFDM
signal. Moreover, for the optimum PAPR reduction performance, code
configuration for Golay and Reed-Muller codes has been identified.
Abstract: Wireless Sensor and Actor Networks (WSANs) constitute an emerging and pervasive technology that is attracting increasing interest in the research community for a wide range of applications. WSANs have two important requirements: coordination interactions and real-time communication to perform correct and timely actions. This paper introduces a methodology to facilitate the task of the application programmer focusing on the coordination and real-time requirements of WSANs. The methodology proposed in this model uses a real-time component model, UM-RTCOM, which will help us to achieve the design and implementation of applications in WSAN by using the component oriented paradigm. This will help us to develop software components which offer some very interesting features, such as reusability and adaptability which are very suitable for WSANs as they are very dynamic environments with rapidly changing conditions. In addition, a high-level coordination model based on tuple channels (TC-WSAN) is integrated into the methodology by providing a component-based specification of this model in UM-RTCOM; this will allow us to satisfy both sensor-actor and actor-actor coordination requirements in WSANs. Finally, we present in this paper the design and implementation of an application which will help us to show how the methodology can be easily used in order to achieve the development of WSANs applications.
Abstract: In this paper, a new design technique for enhancing
bandwidth that improves the performance of a conventional
microstrip patch antenna is proposed. This paper presents a novel
wideband probe fed inverted slotted microstrip patch antenna. The
design adopts contemporary techniques; coaxial probe feeding,
inverted patch structure and slotted patch. The composite effect of
integrating these techniques and by introducing the proposed patch,
offer a low profile, broadband, high gain, and low cross-polarization
level. The results for the VSWR, gain and co-and cross-polarization
patterns are presented. The antenna operating the band of 1.80-2.36
GHz shows an impedance bandwidth (2:1 VSWR) of 27% and a gain
of 10.18 dBi with a gain variation of 1.12 dBi. Good radiation
characteristics, including a cross-polarization level in xz-plane less
than -42 dB, have been obtained.
Abstract: PROFIBUS (PROcess FIeld BUS) which is defined with international standarts (IEC61158, EN50170) is the most popular fieldbus, and provides a communication between industrial applications which are located in different control environment and location in manufacturing, process and building automation. Its communication speed is from 9.6 Kbps to 12 Mbps over distances from 100 to 1200 meters, and so it is to be often necessary to interconnect them in order to break these limits. Unfortunately this interconnection raises several issues and the solutions found so far are not very satisfactory. In this paper, we propose a new solution to interconnect PROFIBUS segments, which uses a wireless MAN based on the IEEE 802.16 standard as a backbone system. Also, the solution which is described a model for internetworking unit integrates the traffic generated by PROFIBUS segments into IEEE 802.16 wireless MAN using encapsulation technique.
Abstract: The impact of rain attenuation on wireless communication signals is predominant because of the used high frequency (above 10 GHz). The knowledge of statistics of attenuation is very important for planning point-to-point microwave links operating in high frequency band. Describing the statistics of attenuation is possible for instance with fade duration or level crossing rate. In our examination we determine these statistics from one year measured data for a given microwave link, and we are going to make an attempt to transform the level crossing rate statistic to fade duration statistic.
Abstract: In wireless and mobile communications, this progress
provides opportunities for introducing new standards and improving
existing services. Supporting multimedia traffic with wireless networks
quality of service (QoS). In this paper, a grey-fuzzy controller for radio
resource management (GF-RRM) is presented to maximize the number
of the served calls and QoS provision in wireless networks. In a
wireless network, the call arrival rate, the call duration and the
communication overhead between the base stations and the control
center are vague and uncertain. In this paper, we develop a method to
predict the cell load and to solve the RRM problem based on the
GF-RRM, and support the present facility has been built on the
application-level of the wireless networks. The GF-RRM exhibits the
better adaptability, fault-tolerant capability and performance than other
algorithms. Through simulations, we evaluate the blocking rate, update
overhead, and channel acquisition delay time of the proposed method.
The results demonstrate our algorithm has the lower blocking rate, less
updated overhead, and shorter channel acquisition delay.
Abstract: Mobile learning (M-learning) integrates mobile
devices and wireless computing technology to enhance the current
conventional learning system. However, there are constraints which
are affecting the implementation of platform and device independent
M-learning. The main aim of this research is to fulfill the following
main objectives: to develop platform independent mobile learning
tool (M-LT) for structured programming course, and evaluate its
effectiveness and usability using ADDIE instructional design model
(ISD) as M-LT life cycle. J2ME (Java 2 micro edition) and XML
(Extensible Markup Language) were used to develop platform
independent M-LT. It has two modules lecture materials and quizzes.
This study used Quasi experimental design to measure effectiveness
of the tool. Meanwhile, questionnaire is used to evaluate the usability
of the tool. Finally, the results show that the system was effective and
also usability evaluation was positive.
Abstract: The development of wireless communication technologies has changed our living style in global level. After the international success of mobile telephony standards, the location and time independent voice connection has become a default method in daily telecommunications. As for today, highly advanced multimedia messaging plays a key role in value added service handling. Along with evolving data services, the need for more complex applications can be seen, including the mobile usage of broadcast technologies. Here performance of a system design for terrestrial multimedia content is examined with emphasis on mobile reception. This review paper has accommodated the understanding of physical layer role and the flavour of terrestrial channel effects on the terrestrial multimedia transmission using OFDM keeping DVB-H as benchmark standard.
Abstract: Wireless sensor network can be applied to both abominable
and military environments. A primary goal in the design of
wireless sensor networks is lifetime maximization, constrained by
the energy capacity of batteries. One well-known method to reduce
energy consumption in such networks is data aggregation. Providing
efcient data aggregation while preserving data privacy is a challenging
problem in wireless sensor networks research. In this paper,
we present privacy-preserving data aggregation scheme for additive
aggregation functions. The Cluster-based Private Data Aggregation
(CPDA)leverages clustering protocol and algebraic properties of
polynomials. It has the advantage of incurring less communication
overhead. The goal of our work is to bridge the gap between
collaborative data collection by wireless sensor networks and data
privacy. We present simulation results of our schemes and compare
their performance to a typical data aggregation scheme TAG, where
no data privacy protection is provided. Results show the efficacy and
efficiency of our schemes.
Abstract: Multiple-input multiple-output (MIMO) systems are
widely in use to improve quality, reliability of wireless transmission
and increase the spectral efficiency. However in MIMO systems,
multiple copies of data are received after experiencing various
channel effects. The limitations on account of complexity due to
number of antennas in case of conventional decoding techniques have
been looked into. Accordingly we propose a modified sphere decoder
(MSD-1) algorithm with lower complexity and give rise to system
with high spectral efficiency. With the aim to increase signal
diversity we apply rotated quadrature amplitude modulation (QAM)
constellation in multi dimensional space. Finally, we propose a new
architecture involving space time trellis code (STTC) concatenated
with space time block code (STBC) using MSD-1 at the receiver for
improving system performance. The system gains have been verified
with channel state information (CSI) errors.
Abstract: In this work, we study the problem of determining
the minimum scheduling length that can satisfy end-to-end (ETE)
traffic demand in scheduling-based multihop WSNs with cooperative
multiple-input multiple-output (MIMO) transmission scheme. Specifically,
we present a cross-layer formulation for the joint routing,
scheduling and stream control problem by incorporating various
power and rate adaptation schemes, and taking into account an
antenna beam pattern model and the signal-to-interference-and-noise
(SINR) constraint at the receiver. In the context, we also propose
column generation (CG) solutions to get rid of the complexity
requiring the enumeration of all possible sets of scheduling links.
Abstract: This paper presents the 20-GHz fractional PLL (Phase
Locked Loop) circuit for the next generation Wi-Fi by using 90 nm
TSMC process. The newly suggested millimeter wave 16/17
pre-scalar is designed and verified by measurement to make the
fractional PLL having a low quantization noise. The operational
bandwidth of the 60 GHz system is 15 % of the carrier frequency
which requires large value of Kv (VCO control gain) resulting in
degradation of phase noise. To solve this problem, this paper adopts
AFC (Automatic Frequency Controller) controlled 4-bit millimeter
wave VCO with small value of Kv. Also constant Kv is implemented
using 4-bit varactor bank. The measured operational bandwidth is 18.2
~ 23.2 GHz which is 25 % of the carrier frequency. The phase noise of
-58 and -96.2 dBc/Hz at 100 KHz and 1 MHz offset is measured
respectively. The total power consumption of the PLL is only 30 mW.
Abstract: Wireless mesh networks based on IEEE 802.11
technology are a scalable and efficient solution for next generation
wireless networking to provide wide-area wideband internet access to
a significant number of users. The deployment of these wireless mesh
networks may be within different authorities and without any
planning, they are potentially overlapped partially or completely in
the same service area. The aim of the proposed model is design a new
model to Enhancement Throughput of Unplanned Wireless Mesh
Networks Deployment Using Partitioning Hierarchical Cluster
(PHC), the unplanned deployment of WMNs are determinates there
performance. We use throughput optimization approach to model the
unplanned WMNs deployment problem based on partitioning
hierarchical cluster (PHC) based architecture, in this paper the
researcher used bridge node by allowing interworking traffic between
these WMNs as solution for performance degradation.
Abstract: With the exponential rise in the number of multimedia
applications available, the best-effort service provided by the Internet
today is insufficient. Researchers have been working on new
architectures like the Next Generation Network (NGN) which, by
definition, will ensure Quality of Service (QoS) in an all-IP based
network [1]. For this approach to become a reality, reservation of
bandwidth is required per application per user. WiMAX (Worldwide
Interoperability for Microwave Access) is a wireless communication
technology which has predefined levels of QoS which can be
provided to the user [4]. IPv6 has been created as the successor for
IPv4 and resolves issues like the availability of IP addresses and
QoS. This paper provides a design to use the power of WiMAX as an
NSP (Network Service Provider) for NGN using IPv6. The use of the
Traffic Class (TC) field and the Flow Label (FL) field of IPv6 has
been explained for making QoS requests and grants [6], [7]. Using
these fields, the processing time is reduced and routing is simplified.
Also, we define the functioning of the ASN gateway and the NGN
gateway (NGNG) which are edge node interfaces in the NGNWiMAX
design. These gateways ensure QoS management through
built in functions and by certain physical resources and networking
capabilities.
Abstract: In this paper, we present a cost-effective wireless
distributed load shedding system for non-emergency scenarios. In
power transformer locations where SCADA system cannot be used,
the proposed solution provides a reasonable alternative that combines
the use of microcontrollers and existing GSM infrastructure to send
early warning SMS messages to users advising them to proactively
reduce their power consumption before system capacity is reached
and systematic power shutdown takes place.
A novel communication protocol and message set have been
devised to handle the messaging between the transformer sites, where
the microcontrollers are located and where the measurements take
place, and the central processing site where the database server is
hosted. Moreover, the system sends warning messages to the endusers
mobile devices that are used as communication terminals. The
system has been implemented and tested via different experimental
results.
Abstract: Using Internet communication, new home electronics
have functions of monitoring and control from remote. However in
many case these electronics work as standalone, and old electronics
are not followed. Then, we developed the total remote system include
not only new electronics but olds. This systems node is a adapter of
electrical power plug that embed relay switch and some sensors, and
these nodes communicate with each other. the system server was build
on the Internet, and users access to this system from web browsers.
To reduce the cost to set up of this system, communication between
adapters are used ZigBee wireless network instead of wired LAN
cable[3]. From measured RSSI(received signal strength indicator)
information between each nodes, the system can estimate roughly
adapters were mounted on which room, and where in the room. So
also it reduces the cost of mapping nodes. Using this system, energy
saving and house monitoring are expected.
Abstract: This work presents a new approach of securing a
wireless network. The configuration is focused on securing &
Protecting wireless network traffic for a small network such as a
home or dorm room. The security Mechanism provided both
authentication, allowing only known authorized users access to the
wireless network, and encryption, preventing anyone from reading
the wireless traffic. The mentioned solution utilizes the open source
free S/WAN software which implements the Internet Protocol
Security –IPSEC. In addition to wireless components, wireless NIC
in PC and wireless access point needs a machine running Linux to act
as security gateway. While the current configuration assumes that the
wireless PC clients are running Linux, Windows XP/VISTA/7 based
machines equipped with VPN software which will allow to interface
with this configuration.
Abstract: In this paper, the effect of receive and/or transmit
antenna spacing on the performance (BER vs. SNR) of multipleantenna
systems is determined by using an RCS (Radar Cross
Section) channel model. In this physical model, the scatterers
existing in the propagation environment are modeled by their RCS so
that the correlation of the receive signal complex amplitudes, i.e.,
both magnitude and phase, can be estimated. The proposed RCS
channel model is then compared with classical models.
Abstract: Multi-Radio Multi-Channel Wireless Mesh Networks (MRMC-WMNs) operate at the backbone to access and route high volumes of traffic simultaneously. Such roles demand high network capacity, and long “online" time at the expense of accelerated transmission energy depletion and poor connectivity. This is the problem of transmission power control. Numerous power control methods for wireless networks are in literature. However, contributions towards MRMC configurations still face many challenges worth considering. In this paper, an energy-efficient power selection protocol called PMMUP is suggested at the Link-Layer. This protocol first divides the MRMC-WMN into a set of unified channel graphs (UCGs). A UCG consists of multiple radios interconnected to each other via a common wireless channel. In each UCG, a stochastic linear quadratic cost function is formulated. Each user minimizes this cost function consisting of trade-off between the size of unification states and the control action. Unification state variables come from independent UCGs and higher layers of the protocol stack. The PMMUP coordinates power optimizations at the network interface cards (NICs) of wireless mesh routers. The proposed PMMUP based algorithm converges fast analytically with a linear rate. Performance evaluations through simulations confirm the efficacy of the proposed dynamic power control.