Abstract: This paper presents the design and implementation of a fully integrated Capacitance-to-Voltage Converter (CVC) as the analog front-end for magnetometer interface IC. The application demands very low power solution operating in the frequency of around 20 KHz. The design adapts low power architecture to create low noise electronic interface for Capacitive Micro-machined Lorentz force magnetometer sensor. Using a 0.18-μm CMOS process, simulation results of this interface IC show that the proposed CVC can provide 33 dB closed loop gain, 20 nV/√Hz input referred noise at 20 KHz, while consuming 65 μA current from 1.8-V supply.
Abstract: In this paper a genetic algorithm (GA) with dual-fitness function is proposed and applied to solve the deterministic identical machine scheduling problem. The mating fitness function value was used to determine the mating for chromosomes, while the selection fitness function value was used to determine their survivals. The performance of this algorithm was tested on deterministic identical machine scheduling using simulated data. The results obtained from the proposed GA were compared with classical GA and integer programming (IP). Results showed that dual-fitness function GA outperformed the classical single-fitness function GA with statistical significance for large problems and was competitive to IP, particularly when large size problems were used.
Abstract: The industrial automation is dependent upon pneumatic control systems. The industrial units are now controlled with digital control systems to tackle the process variables like Temperature, Pressure, Flow rates and Composition.
This research work produces an evaluation of the response time fluctuations for proportional mode, proportional integral and proportional integral derivative modes of automated chemical process control. The controller output is measured for different values of gain with respect to time in three modes (P, PI and PID). In case of P-mode for different values of gain the controller output has negligible change. When the controller output of PI-mode is checked for constant gain, it can be seen that by decreasing the integral time the controller output has showed more fluctuations. The PID mode results have found to be more interesting in a way that when rate minute has changed, the controller output has also showed fluctuations with respect to time. The controller output for integral mode and derivative mode are observed with lesser steady state error, minimum offset and larger response time to control the process variable. The tuning parameters in case of P-mode are only steady state gain with greater errors with respect to controller output. The integral mode showed controller outputs with intermediate responses during integral gain (ki). By increasing the rate minute the derivative gain (kd) also increased which showed the controlled oscillations in case of PID mode and lesser overshoot.
Abstract: The problem of optimal planning of multiple sources
of distributed generation (DG) in distribution networks is treated in
this paper using an improved Ant Colony Optimization algorithm
(ACO). This objective of this problem is to determine the DG
optimal size and location that in order to minimize the network real
power losses. Considering the multiple sources of DG, both size and
location are simultaneously optimized in a single run of the proposed
ACO algorithm. The various practical constraints of the problem are
taken into consideration by the problem formulation and the
algorithm implementation. A radial power flow algorithm for
distribution networks is adopted and applied to satisfy these
constraints. To validate the proposed technique and demonstrate its
effectiveness, the well-know 69-bus feeder standard test system is
employed.cm.
Abstract: In power system protection, the need to know the load
current together with the fault level detected by a relay is important.
This is due to the fact that the relay is required to isolate the
equipment being protected if a fault is present and keep the breaker
associated with it closed if the current level is lower than the
maximum load level. This is not an issue for a radial system. This is
not the same however in a looped power system. In a looped power
system, the isolation of an equipment system will contribute to a
topology change. The change in the power system topology will then
influence or change the maximum load current and the fault level
detected by each relay. In this paper, a method of data collection for
changing topology using matlab and sim-power will be presented.
The method will take into consideration the change in topology and
collect data for each possible topology.
Abstract: In biomedical implant field, a new formula is given
for the study of Radio Frequency power attenuation by simultaneous
effects of side and angular misalignment of the supply/data transfer
coils. A confrontation with the practical measurements done into a
Faraday cage, allowed a checking of the obtained theoretical results.
The DC supply systems without material connection and the data
transmitters used in the case of biomedical implants, can be well
dimensioned by taking into account the possibility of power
attenuation by misalignment of transfer coils
Abstract: This paper explains a novel approach to human interactive e-learning systems using head posture images. Students- face and hair information are used to identify a human presence and estimate the gaze direction. We then define the human-computer interaction level and test the definition using ten students and seventy different posture images. The experimental results show that head posture images provide adequate information for increasing human-computer interaction in e-learning systems.
Abstract: This paper addresses the analysis of the interference between complementary ground component (CGC) base station and mobile earth station (MES). In the frequency sharing scenario between CGC base station and MES, the interference from the adjacent beams must be considered. In this paper, we estimated the interference to MES of an integrated satellite system and the result is presented as the carrier to interference ratio(C/I) with respect to the number of CGC base station in the adjacent beam and the ratio of satellite beam center radius to the total beam radius (R1/R). By using these results, we can determine the minimum separation distance between the CGC base stations of adjacent beam and MES for compatibility. This result can be applied to the CGC base station of an integrated satellite system for the effective frequency sharing.
Abstract: Development of microprocessor controlled sensor for measurement of wind speed and direction is the aim of this study. Electrical circuits and software were developed to the existing electromechanical part of the sensor TM-W2 becoming the properties of so-called smart sensor. The measured data about wind speed (sensitivity 0.01 m/s) and direction (0-360° by step 10°) are transmitted as 16-bit information. The connection between sensor and control unit is realized by radio communication (FM 433 MHz). Transition range is 220 m if used Quad type antenna. This concept provides substitution of actual cable systems by wireless ones.
Abstract: In this paper, we present a comparative study of the
genetic algorithms and Hessian-s methods for optimal research of the
active powers in an electric network of power. The objective function
which is the performance index of production of electrical energy is
minimized by satisfying the constraints of the equality type and
inequality type initially by the Hessian-s methods and in the second
time by the genetic Algorithms. The results found by the application
of AG for the minimization of the electric production costs of power
are very encouraging. The algorithms seem to be an effective
technique to solve a great number of problems and which are in
constant evolution. Nevertheless it should be specified that the
traditional binary representation used for the genetic algorithms
creates problems of optimization of management of the large-sized
networks with high numerical precision.
Abstract: The electrical power systems of aircrafts have made
serious progress in recent years because the aircrafts depend more
and more on the electricity. There is a trend in the aircraft industry to
replace hydraulic and pneumatic systems with electrical systems,
achieving more comfort and monitoring features and enlarging the
energetic efficiency. Thus, was born the concept More Electric
Aircraft. In this paper is analyzed the integration of a fuel cell into
the existing electrical generation and distribution systems of an
aircraft. The dynamic characteristics of fuel cell systems necessitate
an adaptation of the electrical power system. The architecture studied
in this paper consists of a 50kW fuel cell, a dc to dc converter and
several loads. The dc to dc converter is used to step down the fuel
cell voltage from about 625Vdc to 28Vdc.
Abstract: A new Meta heuristic approach called "Randomized gravitational emulation search algorithm (RGES)" for solving large size set covering problems has been designed. This algorithm is found upon introducing randomization concept along with the two of the four primary parameters -velocity- and -gravity- in physics. A new heuristic operator is introduced in the domain of RGES to maintain feasibility specifically for the set covering problem to yield best solutions. The performance of this algorithm has been evaluated on a large set of benchmark problems from OR-library. Computational results showed that the randomized gravitational emulation search algorithm - based heuristic is capable of producing high quality solutions. The performance of this heuristic when compared with other existing heuristic algorithms is found to be excellent in terms of solution quality.
Abstract: A reconfigurable manufacturing system (RMS) is an
advanced system designed at the outset for rapid changes in its hardware
and software components in order to quickly adjust its production
capacity and functionally. Among various operational decisions, this
study considers the scheduling problem that determines the input
sequence and schedule at the same time for a given set of parts. In
particular, we consider the practical constraints that the numbers of
pallets/fixtures are limited and hence a part can be released into the
system only when the fixture required for the part is available. To
solve the integrated input sequencing and scheduling problems, we
suggest a priority rule based approach in which the two sub-problems
are solved using a combination of priority rules. To show the effectiveness
of various rule combinations, a simulation experiment was
done on the data for a real RMS, and the test results are reported.
Abstract: In this paper, the existence, multiplicity and
noexistence of positive solutions for a class of semipositone
discrete boundary value problems with two parameters is
studied by applying nonsmooth critical point theory and
sub-super solutions method.
Abstract: In this study, the static behavior of super elliptical Winkler plate is analyzed by applying the double side approach method. The lack of information about super elliptical Winkler plates is the motivation of this study and we use the double side approach method to solve this problem because of its superior ability on efficiently treating problems with complex boundary shape. The double side approach method has the advantages of high accuracy, easy calculation procedure and less calculation load required. Most important of all, it can give the error bound of the approximate solution. The numerical results not only show that the double side approach method works well on this problem but also provide us the knowledge of static behavior of super elliptical Winkler plate in practical use.
Abstract: In order to integrate knowledge in heterogeneous
case-based reasoning (CBR) systems, ontology-based CBR system
has become a hot topic. To solve the facing problems of
ontology-based CBR system, for example, its architecture is
nonstandard, reusing knowledge in legacy CBR is deficient, ontology
construction is difficult, etc, we propose a novel approach for
semi-automatically construct ontology-based CBR system whose
architecture is based on two-layer ontology. Domain knowledge
implied in legacy case bases can be mapped from relational database
schema and knowledge items to relevant OWL local ontology
automatically by a mapping algorithm with low time-complexity. By
concept clustering based on formal concept analysis, computing
concept equation measure and concept inclusion measure, some
suggestions about enriching or amending concept hierarchy of OWL
local ontologies are made automatically that can aid designers to
achieve semi-automatic construction of OWL domain ontology.
Validation of the approach is done by an application example.
Abstract: This paper presents a customized deformable model
for the segmentation of abdominal and thoracic aortic aneurysms in
CTA datasets. An important challenge in reliably detecting aortic
aneurysm is the need to overcome problems associated with intensity
inhomogeneities and image noise. Level sets are part of an important
class of methods that utilize partial differential equations (PDEs) and
have been extensively applied in image segmentation. A Gaussian
kernel function in the level set formulation, which extracts the local
intensity information, aids the suppression of noise in the extracted
regions of interest and then guides the motion of the evolving contour
for the detection of weak boundaries. The speed of curve evolution
has been significantly improved with a resulting decrease in
segmentation time compared with previous implementations of level
sets. The results indicate the method is more effective than other
approaches in coping with intensity inhomogeneities.
Abstract: Absorption spectra of infra-red (IR) radiation of the
disperse water medium absorbing the most important greenhouse
gases: CO2 , N2O , CH4 , C2H2 , C2H6 have been calculated by
the molecular dynamics method. Loss of the absorbing ability at the
formation of clusters due to a reduction of the number of centers
interacting with IR radiation, results in an anti-greenhouse effect.
Absorption of O3 molecules by the (H2O)50 cluster is investigated
at its interaction with Cl- ions. The splitting of ozone molecule on
atoms near to cluster surface was observed. Interaction of water
cluster with Cl- ions causes the increase of integrated intensity of
emission spectra of IR radiation, and also essential reduction of the
similar characteristic of Raman spectrum. Relative integrated
intensity of absorption of IR radiation for small water clusters was
designed. Dependences of the quantity of weight on altitude for
vapor of monomers, clusters, droplets, crystals and mass of all
moisture were determined. The anti-greenhouse effect of clusters was
defined as the difference of increases of average global temperature
of the Earth, caused by absorption of IR radiation by free water
molecules forming clusters, and absorption of clusters themselves.
The greenhouse effect caused by clusters makes 0.53 K, and the antigreenhouse
one is equal to 1.14 K. The increase of concentration of
CO2 in the atmosphere does not always correlate with the
amplification of greenhouse effect.
Abstract: An efficient reintegration of the disabled people in the
family and society should be fulfilled; hence it is strongly needful to assist their diminished functions or to replace the totally lost
functions. Assistive technology helps in neutralizing the impairment.
Recent advancements in embedded systems have opened up a vast
area of research and development for affordable and portable assistive devices for the visually impaired. Granted there are many assistive devices on the market that are able to detect obstacles, and numerous research and development currently in process to
alleviate the cause, unfortunately the cost of devices, size of
devices, intrusiveness and higher learning curve prevents the visually impaired from taking advantage of available devices. This
project aims at the design and implementation of a detachable unit
which is robust, low cost and user friendly, thus, trying to
aggrandize the functionality of the existing white cane, to concede above-knee obstacle detection. The designed obstruction detector
uses ultrasound sensors for detecting the obstructions before direct contact. It bestows haptic feedback to the user in accordance with the position of the obstacle.
Abstract: A gradient learning method to regulate the trajectories
of some nonlinear chaotic systems is proposed. The method is
motivated by the gradient descent learning algorithms for neural
networks. It is based on two systems: dynamic optimization system
and system for finding sensitivities. Numerical results of several
examples are presented, which convincingly illustrate the efficiency
of the method.