Abstract: A Data Warehouses is a repository of information
integrated from source data. Information stored in data warehouse is
the form of materialized in order to provide the better performance
for answering the queries. Deciding which appropriated views to be
materialized is one of important problem. In order to achieve this
requirement, the constructing search space close to optimal is a
necessary task. It will provide effective result for selecting view to be
materialized. In this paper we have proposed an approach to reoptimize
Multiple View Processing Plan (MVPP) by using global
common subexpressions. The merged queries which have query
processing cost not close to optimal would be rewritten. The
experiment shows that our approach can help to improve the total
query processing cost of MVPP and sum of query processing cost
and materialized view maintenance cost is reduced as well after views
are selected to be materialized.
Abstract: A frictionless contact problem for a two-layer orthotropic elastic medium loaded through a rigid flat stamp is considered. It is assumed that tensile tractions are not allowed and only compressive tractions can be transmitted across the interface. In the solution, effect of gravity is taken into consideration. If the external load on the rigid stamp is less than or equal to a critical value, continuous contact between the layers is maintained. The problem is expressed in terms of a singular integral equation by using the theory of elasticity and the Fourier transforms. Numerical results for initial separation point, critical separation load and contact stress distribution are presented.
Abstract: This research paper presents the CFD analysis of
oscillating airfoil during pitch cycle. Unsteady subsonic flow is
simulated for pitching airfoil at Mach number 0.283 and Reynolds
number 3.45 millions. Turbulent effects are also considered for this
study by using K-ω SST turbulent model. Two-dimensional unsteady
compressible Navier-Stokes code including two-equation turbulence
model and PISO pressure velocity coupling is used. Pressure based
implicit solver with first order implicit unsteady formulation is used.
The simulated pitch cycle results are compared with the available
experimental data. The results have a good agreement with the
experimental data. Aerodynamic characteristics during pitch cycles
have been studied and validated.
Abstract: Commercial hydroxyapatite (HA) was reinforced by
adding 2, 5, and 10 wt % of 28.5%CaO-28.5%P2O5-38%Na2 O-
5%CaF2 based glass and then sintered. Although HA shows good
biocompatibility with the human body, its applications are limited to
non load-bearing areas and coatings due to its poor mechanical
properties. These mechanical properties can be improved
substantially with addition of glass ceramics by sintering. In this
study, the effects of sintering hydroxyapatite with above specified
phosphate glass additions are quantified. Each composition was
sintered over a range of temperatures. Scanning electron microscopy
and x-ray diffraction were used to characterize the microstructure and
phases of the composites. The density, microhardness, and
compressive strength were measured using Archimedes Principle,
Vickers Microhardness Tester (at 0.98 N), and Instron Universal
Testing Machine (cross speed of 0.5 mm/min) respectively. These
results were used to indicate which composition provided suitable
material for use in hard tissue replacement. Composites containing 10
wt % glass additions formed dense HA/TCP (tricalcium phosphate)
composite materials possessing good compressive strength and
hardness than HA. In-vitro bioactivity was assessed by evaluating
changes in pH and Ca2+ ion concentration of SBF-simulated body
fluid on immersion of these composites in it for two weeks.
Abstract: A one-step conservative level set method, combined with a global mass correction method, is developed in this study to simulate the incompressible two-phase flows. The present framework do not need to solve the conservative level set scheme at two separated steps, and the global mass can be exactly conserved. The present method is then more efficient than two-step conservative level set scheme. The dispersion-relation-preserving schemes are utilized for the advection terms. The pressure Poisson equation solver is applied to GPU computation using the pCDR library developed by National Center for High-Performance Computing, Taiwan. The SMP parallelization is used to accelerate the rest of calculations. Three benchmark problems were done for the performance evaluation. Good agreements with the referenced solutions are demonstrated for all the investigated problems.
Abstract: Facial expression analysis is rapidly becoming an
area of intense interest in computer science and human-computer
interaction design communities. The most expressive way humans
display emotions is through facial expressions. In this paper we
present a method to analyze facial expression from images by
applying Gabor wavelet transform (GWT) and Discrete Cosine
Transform (DCT) on face images. Radial Basis Function (RBF)
Network is used to classify the facial expressions. As a second stage,
the images are preprocessed to enhance the edge details and non
uniform down sampling is done to reduce the computational
complexity and processing time. Our method reliably works even
with faces, which carry heavy expressions.
Abstract: The effects of different parameters on the
hydrodynamics of trickle bed reactors were discussed for Newtonian
and non-Newtonian foaming systems. The varying parameters are
varying liquid velocities, gas flow velocities and surface tension. The
range for gas velocity is particularly large, thanks to the use of dense
gas to simulate very high pressure conditions. This data bank has
been used to compare the prediction accuracy of the different
trendlines and transition points from the literature. More than 240
experimental points for the trickle flow (GCF) and foaming pulsing
flow (PF/FPF) regime were obtained for present study.
Hydrodynamic characteristics involving dynamic liquid saturation
significantly influenced by gas and liquid flow rates. For 15 and 30
ppm air-aqueous surfactant solutions, dynamic liquid saturation
decreases with higher liquid and gas flow rates considerably in high
interaction regime. With decrease in surface tension i.e. for 45 and 60
ppm air-aqueous surfactant systems, effect was more pronounced
with decreases dynamic liquid saturation very sharply during regime
transition significantly at both low liquid and gas flow rates.
Abstract: Judgment is affected by many agents and distortion in this assessment is unpreventable. Personality dimensions are among those factors that interfere with the distortion. In this research, the relations between personality dimensions of subject and his judgment on friends- personality dimensions is investigated. One-hundred friend couples completed both NEO Five Factor Inventory (NEOFFI) and Ahvaz Reality Distortion Inventory (ARDI) to make judgments about themselves and their friends. Observations show that judge-s Agreement and Neuroticism dimensions are impressed by reality distortion. On the other hand, this reality distortion interferes with one-s evaluation of his friend-s Agreement, Neuroticism, and Conscientiousness dimensions. Conscientiousness with suppressive effect on judge-s other dimensions plays the irrelevant role on personality judgment. Therefore, observer-rating tools which are used as a conventional criterion seem to be not valid because of the reality distortion due to judge-s personality dimensions.
Abstract: In this study, hydroxyapatite (HA) composites are
prepared on addition of 30%CaO-30%P2O5-40%Na2 O based glass to
pure HA, in proportion of 2, 5, and 10 wt %. Each composition was
sintered over a range of temperatures. The quantitative phase
analysis was carried out using XRD and the microstructures were
studied using SEM. The density, microhardness, and compressive
strength have shown increase with the increasing amount of glass
addition. The resulting composites have chemical compositions that
are similar to the inorganic constituent of the mineral part of bone,
and constitutes trace elements like Na. X-ray diffraction showed no
decomposition of HA to secondary phases, however, the glass
reinforced-HA composites contained a HA phase and variable
amounts of tricalcium phosphate phase, depending on the amount of
bioglass added. The HA-composite material exhibited higher
compressive strength compared to sintered HA. The HA composite
reinforced with 10 wt % bioglass showed highest bioactivity level.
Abstract: Sputter deposition processes, especially for sputtering
from metal targets, are well investigated. For practical reasons, i.e.
for industrial processes, energetic considerations for sputter
deposition are useful in order to optimize the sputtering process. In
particular, for substrates at floating conditions it is required to obtain
energetic conditions during film growth that enables sufficient dense
metal films of good quality. The influence of ion energies, energy
density and momentum transfer is thus examined both for sputtering
at the target as well as during film growth. Different regimes
dominated by ion energy, energy density and momentum transfer
were identified by using different plasma sources and by varying
power input, pressure and bias voltage.
Abstract: Finite element method was applied to model damage
development in the femoral neck during a sideways fall. The femoral
failure was simulated using the maximum principal strain criterion.
The evolution of damage was consistent with previous studies. It was
initiated by compressive failure at the junction of the superior aspect
of the femoral neck and the greater trochanter. It was followed by
tensile failure that occurred at the inferior aspect of the femoral neck
before a complete transcervical fracture was observed. The estimated
failure line was less than 50° from the horizontal plane (Pauwels type
II).
Abstract: The PAX6, a transcription factor, is essential for the morphogenesis of the eyes, brain, pituitary and pancreatic islets. In rodents, the loss of Pax6 function leads to central nervous system defects, anophthalmia, and nasal hypoplasia. The haplo-insufficiency of Pax6 causes microphthalmia, aggression and other behavioral abnormalities. It is also required in brain patterning and neuronal plasticity. In human, heterozygous mutation of Pax6 causes loss of iris [aniridia], mental retardation and glucose intolerance. The 3- deletion in Pax6 leads to autism and aniridia. The phenotypes are variable in peneterance and expressivity. However, mechanism of function and interaction of PAX6 with other proteins during development and associated disease are not clear. It is intended to explore interactors of PAX6 to elucidated biology of PAX6 function in the tissues where it is expressed and also in the central regulatory pathway. This report describes In-silico approaches to explore interacting proteins of PAX6. The models show several possible proteins interacting with PAX6 like MITF, SIX3, SOX2, SOX3, IPO13, TRIM, and OGT. Since the Pax6 is a critical transcriptional regulator and master control gene of eye and brain development it might be interacting with other protein involved in morphogenesis [TGIF, TGF, Ras etc]. It is also presumed that matricelluar proteins [SPARC, thrombospondin-1 and osteonectin etc] are likely to interact during transport and processing of PAX6 and are somewhere its cascade. The proteins involved in cell survival and cell proliferation can also not be ignored.
Abstract: Gas turbine air inlet cooling is a useful method for
increasing output for regions where significant power demand and
highest electricity prices occur during the warm months. Inlet air
cooling increases the power output by taking advantage of the gas
turbine-s feature of higher mass flow rate when the compressor inlet
temperature decreases. Different methods are available for reducing
gas turbine inlet temperature. There are two basic systems currently
available for inlet cooling. The first and most cost-effective system is
evaporative cooling. Evaporative coolers make use of the evaporation
of water to reduce the gas turbine-s inlet air temperature. The second
system employs various ways to chill the inlet air. In this method, the
cooling medium flows through a heat exchanger located in the inlet
duct to remove heat from the inlet air. However, the evaporative
cooling is limited by wet-bulb temperature while the chilling can cool
the inlet air to temperatures that are lower than the wet bulb
temperature. In the present work, a thermodynamic model of a gas
turbine is built to calculate heat rate, power output and thermal
efficiency at different inlet air temperature conditions. Computational
results are compared with ISO conditions herein called "base-case".
Therefore, the two cooling methods are implemented and solved for
different inlet conditions (inlet temperature and relative humidity).
Evaporative cooler and absorption chiller systems results show that
when the ambient temperature is extremely high with low relative
humidity (requiring a large temperature reduction) the chiller is the
more suitable cooling solution. The net increment in the power output
as a function of the temperature decrease for each cooling method is
also obtained.
Abstract: We study in this paper the effect of the scene
changing on image sequences coding system using Embedded
Zerotree Wavelet (EZW). The scene changing considered here is the
full motion which may occurs. A special image sequence is generated
where the scene changing occurs randomly. Two scenarios are
considered: In the first scenario, the system must provide the
reconstruction quality as best as possible by the management of the
bit rate (BR) while the scene changing occurs. In the second scenario,
the system must keep the bit rate as constant as possible by the
management of the reconstruction quality. The first scenario may be
motivated by the availability of a large band pass transmission
channel where an increase of the bit rate may be possible to keep the
reconstruction quality up to a given threshold. The second scenario
may be concerned by the narrow band pass transmission channel
where an increase of the bit rate is not possible. In this last case,
applications for which the reconstruction quality is not a constraint
may be considered. The simulations are performed with five scales
wavelet decomposition using the 9/7-tap filter bank biorthogonal
wavelet. The entropy coding is performed using a specific defined
binary code book and EZW algorithm. Experimental results are
presented and compared to LEAD H263 EVAL. It is shown that if
the reconstruction quality is the constraint, the system increases the
bit rate to obtain the required quality. In the case where the bit rate
must be constant, the system is unable to provide the required quality
if the scene change occurs; however, the system is able to improve
the quality while the scene changing disappears.
Abstract: MATCH project [1] entitle the development of an
automatic diagnosis system that aims to support treatment of colon
cancer diseases by discovering mutations that occurs to tumour
suppressor genes (TSGs) and contributes to the development of
cancerous tumours. The constitution of the system is based on a)
colon cancer clinical data and b) biological information that will be
derived by data mining techniques from genomic and proteomic
sources The core mining module will consist of the popular, well
tested hybrid feature extraction methods, and new combined
algorithms, designed especially for the project. Elements of rough
sets, evolutionary computing, cluster analysis, self-organization maps
and association rules will be used to discover the annotations
between genes, and their influence on tumours [2]-[11].
The methods used to process the data have to address their high
complexity, potential inconsistency and problems of dealing with the
missing values. They must integrate all the useful information
necessary to solve the expert's question. For this purpose, the system
has to learn from data, or be able to interactively specify by a domain
specialist, the part of the knowledge structure it needs to answer a
given query. The program should also take into account the
importance/rank of the particular parts of data it analyses, and adjusts
the used algorithms accordingly.
Abstract: The major part of light weight timber constructions
consists of insulation. Mineral wool is the most commonly used
insulation due to its cost efficiency and easy handling. The fiber
orientation and porosity of this insulation material enables flowthrough.
The air flow resistance is low. If leakage occurs in the
insulated bay section, the convective flow may cause energy losses
and infiltration of the exterior wall with moisture and particles. In
particular the infiltrated moisture may lead to thermal bridges and
growth of health endangering mould and mildew. In order to prevent
this problem, different numerical calculation models have been
developed. All models developed so far have a potential for
completion. The implementation of the flow-through properties of
mineral wool insulation may help to improve the existing models.
Assuming that the real pressure difference between interior and
exterior surface is larger than the prescribed pressure difference in the
standard test procedure for mineral wool ISO 9053 / EN 29053,
measurements were performed using the measurement setup for
research on convective moisture transfer “MSRCMT".
These measurements show, that structural inhomogeneities of
mineral wool effect the permeability only at higher pressure
differences, as applied in MSRCMT. Additional microscopic
investigations show, that the location of a leak within the
construction has a crucial influence on the air flow-through and the
infiltration rate. The results clearly indicate that the empirical values
for the acoustic resistance of mineral wool should not be used for the
calculation of convective transfer mechanisms.
Abstract: In the area where the high quality water is not
available, unconventional water sources are used to irrigate.
Household leachate is one of the sources which are used in dry and
semi dry areas in order to water the barer trees and plants. It meets
the plants needs and also has some effects on the soil, but at the same
time it might cause some problems as well. This study in order to
evaluate the effect of using Compost leachate on the density of soil
iron in form of a statistical pattern called ''Split Plot'' by using two
main treatments, one subsidiary treatment and three repetitions of the
pattern in a three month period. The main N treatments include:
irrigation using well water as a blank treatments and the main I
treatments include: irrigation using leachate and well water
concurrently. Some subsidiary treatments were DI (Drop Irrigation)
and SDI (Sub Drop Irrigation). Then in the established plots, 36
biannual pine and cypress shrubs were randomly grown. Two months
later the treatment begins. The results revealed that there was a
significant variation between the main treatment and the instance
regarding pH decline in the soil which was related to the amount of
leachate injected into the soil. After some time and using leachate the
pH level fell, as much as 0.46 and also increased due to the great
amounts of leachate. The underneath drop irrigation ends in better
results than sub drop irrigation since it keeps the soil texture fixed.
Abstract: Perturbed-Chain Statistical Association Fluid Theory (PC-SAFT) equation of state (EOS) is a modified SAFT EOS with three pure component specific parameters: segment number (m), diameter (σ) and energy (ε). These PC-SAFT parameters need to be determined for each component under the conditions of interest by fitting experimental data, such as vapor pressure, density or heat capacity. PC-SAFT parameters for propane, ethylene and hydrogen in supercritical region were successfully estimated by fitting experimental density data available in literature. The regressed PCSAFT parameters were compared with the literature values by means of estimating pure component density and calculating average absolute deviation between the estimated and experimental density values. PC-SAFT parameters available in literature especially for ethylene and hydrogen estimated density in supercritical region reasonably well. However, the regressed PC-SAFT parameters performed better in supercritical region than the PC-SAFT parameters from literature.
Abstract: Demolitions of buildings have created a lot of waste
and one of it is clay bricks. The waste clay bricks were ground to
roughly cement fineness and used to partially replaced cement at
10%, 20% and 30% with w/b ratio of 0.6 and tested at 7, 28, 60, 90
and 120 days. The result shows that the compressive strength of GCB
concrete increases over age however, decreases as the level of
replacements increases. It was also found that 10% replacement of
GCB gave the highest compressive strength, however for optimum
replacement, 30% was chosen as it still attained strength of grade 30
concrete. In terms of durability performances, results show that GCB
replacement up to 30% was found to be efficient in reducing water
absorption as well as water permeability. These studies show that
GCB has the potential to be used as partial cement replacement in
making concrete.
Abstract: Kepsut-Dursunbey volcanic field (KDVF) is located
in NW Turkey and contains various products of the post-collisional
Neogene magmatic activity. Two distinct volcanic suites have been
recognized; the Kepsut volcanic suite (KVS) and the Dursunbey
volcanic suite (DVS). The KVS includes basaltic trachyandesitebasaltic
andesite-andesite lavas and associated pyroclastic rocks. The
DVS consists of dacite-rhyodacite lavas and extensive pumice-ash
fall and flow deposits. Petrographical features (i.e. existence of
xenocrysts, glomerocrysts, and mixing-compatible textures) and
mineral chemistry of phenocryst assemblages of both suites provide
evidence for magma mixing/AFC. Calculated crystallization
pressures and temperatures give values of 5.7–7.0 kbar and 927–982
°C for the KVS and 3.7–5.3 kbar and 783-787°C for the DVS,
indicating separate magma reservoirs and crystallization in magma
chambers at deep and mid crustal levels, respectively. These
observations support the establishment and evolution of KDVF
magma system promoted by episodic basaltic inputs which may
generate and mix with crustal melts.