Abstract: The quest for alternatefuels for a CI engine has
become all the more imperative considering its importance in the
economy of a nation and from the standpoint of preserving the environment. Reported in this paper are the combustion performance and P-θ characteristics of a CI engine operating on B20 biodiesel fuel derived from Jatropha oil.Itis observed that the twin effect of advancing the injection timing and increasing the injector opening pressure (IOP) up to 220 barhas resulted in minimum brake specific
energy consumption and higherpeak pressure. It is also observed that
the crank angle of occurrence of peak pressure progressestowards top
dead center (TDC) as the timing is advanced and IOP is increased.
Abstract: The paper discusses a computationally efficient
method for the design of prototype filters required for the
implementation of an M-band cosine modulated filter bank. The
prototype filter is formulated as an optimum interpolated FIR filter.
The optimum interpolation factor requiring minimum number of
multipliers is used. The model filter as well as the image suppressor
will be designed using the Kaiser window. The method will seek to
optimize a single parameter namely cutoff frequency to minimize the
distortion in the overlapping passband.
Abstract: Gas hydrates can agglomerate and block multiphase oil and gas pipelines when water is present at hydrate forming conditions. Using "Cold Flow Technology", the aim is to condition gas hydrates so that they can be transported as a slurry mixture without a risk of agglomeration. During the pipeline shut down however, hydrate particles may settle in bends and build hydrate plugs. An experimental setup has been designed and constructed to study the flow of such plugs at start up operations. Experiments have been performed using model fluid and model hydrate particles. The propagations of initial plugs in a bend were recorded with impedance probes along the pipe. The experimental results show a dispersion of the plug front. A peak in pressure drop was also recorded when the plugs were passing the bend. The evolutions of the plugs have been simulated by numerical integration of the incompressible mass balance equations, with an imposed mixture velocity. The slip between particles and carrier fluid has been calculated using a drag relation together with a particle-fluid force balance.
Abstract: In research on natural ventilation, and passive cooling
with forced convection, is essential to know how heat flows in a solid
object and the pattern of temperature distribution on their surfaces,
and eventually how air flows through and convects heat from the
surfaces of steel under roof. This paper presents some results from
running the computational fluid dynamic program (CFD) by
comparison between natural ventilation and forced convection within
roof attic that is received directly from solar radiation. The CFD
program for modeling air flow inside roof attic has been modified to
allow as two cases. First case, the analysis under natural ventilation,
is closed area in roof attic and second case, the analysis under forced
convection, is opened area in roof attic. These extend of all cases to
available predictions of variations such as temperature, pressure, and
mass flow rate distributions in each case within roof attic. The
comparison shows that this CFD program is an effective model for
predicting air flow of temperature and heat transfer coefficient
distribution within roof attic. The result shows that forced convection
can help to reduce heat transfer through roof attic and an around area
of steel core has temperature inner zone lower than natural
ventilation type. The different temperature on the steel core of roof
attic of two cases was 10-15 oK.
Abstract: The development of the signal compression
algorithms is having compressive progress. These algorithms are
continuously improved by new tools and aim to reduce, an average,
the number of bits necessary to the signal representation by means of
minimizing the reconstruction error. The following article proposes
the compression of Arabic speech signal by a hybrid method
combining the wavelet transform and the linear prediction. The
adopted approach rests, on one hand, on the original signal
decomposition by ways of analysis filters, which is followed by the
compression stage, and on the other hand, on the application of the
order 5, as well as, the compression signal coefficients. The aim of
this approach is the estimation of the predicted error, which will be
coded and transmitted. The decoding operation is then used to
reconstitute the original signal. Thus, the adequate choice of the
bench of filters is useful to the transform in necessary to increase the
compression rate and induce an impercevable distortion from an
auditive point of view.
Abstract: The fluid mechanics principle is used extensively in
designing axial flow fans and their associated equipment. This paper presents a computational fluid dynamics (CFD) modeling of air flow
distribution from a radiator axial flow fan used in an acid pump truck Tier4 (APT T4) Repower. This axial flow fan augments the transfer
of heat from the engine mounted on the APT T4.
CFD analysis was performed for an area weighted average static pressure difference at the inlet and outlet of the fan. Pressure contours, velocity vectors, and path lines were plotted for detailing
the flow characteristics for different orientations of the fan blade. The results were then compared and verified against known theoretical observations and actual experimental data. This study
shows that a CFD simulation can be very useful for predicting and understanding the flow distribution from a radiator fan for further
research work.
Abstract: This paper presents image compression with wavelet based method. The wavelet transformation divides image to low- and high pass filtered parts. The traditional JPEG compression technique requires lower computation power with feasible losses, when only compression is needed. However, there is obvious need for wavelet based methods in certain circumstances. The methods are intended to the applications in which the image analyzing is done parallel with compression. Furthermore, high frequency bands can be used to detect changes or edges. Wavelets enable hierarchical analysis for low pass filtered sub-images. The first analysis can be done for a small image, and only if any interesting is found, the whole image is processed or reconstructed.
Abstract: This paper examines many mathematical methods for
molding the hourly price forward curve (HPFC); the model will be
constructed by numerous regression methods, like polynomial
regression, radial basic function neural networks & a furrier series.
Examination the models goodness of fit will be done by means of
statistical & graphical tools. The criteria for choosing the model will
depend on minimize the Root Mean Squared Error (RMSE), using the
correlation analysis approach for the regression analysis the optimal
model will be distinct, which are robust against model
misspecification. Learning & supervision technique employed to
determine the form of the optimal parameters corresponding to each
measure of overall loss. By using all the numerical methods that
mentioned previously; the explicit expressions for the optimal model
derived and the optimal designs will be implemented.
Abstract: In this paper, an authentication system using keystroke dynamics is presented. We introduced pressure sensing for the improvement of the accuracy of measurement and durability against intrusion using key-logger, and so on, however additional instrument is needed. As the result, it has been found that the pressure sensing is also effective for estimation of real moment of keystroke.
Abstract: Jacobs, A.B. (1993) stated that "When I think of a city,
the first thing that comes to mind is the street. If the street is
interesting, the rest of the city is interesting. If the street is mundane,
the city is also mundane." In this statement, he expresses the
importance of the streetscape and the street environment. The
objective of this paper is to analyze the spatial relationships of the
streetscape that affect the general public's preference of the cityscape.
Furthermore, this research focuses on the important role that
streetscape plays in public perception of the city by the pedestrians
who experience it daily. The subject of this paper is eight of the
"Design Seoul Street."The analysis and survey results show the
preference criteria that affect the streetscape and ultimately the
cityscape. This research endeavor shows that differences in physical
form, shape, size, color, locations, and context are important.
Abstract: In this study, the thermal and mechanical properties of
basalt fibre reinforced concrete were investigated. The volume
fractions of basalt fibre of (0.1, 0.2, 0.3, and 0.5% by total mix
volume) were used. Properties such as heat transfer, compressive and
splitting tensile strengths were examined. Results indicated that the
strength increases with increase the fibre content till 0.3% then there
is a slight reduction when 0.5% fibre used. Lower amount of heat
conducted through the thickness of concrete specimens than the
conventional concrete was also recorded.
Abstract: In this work, we present a comparison between two
techniques of image compression. In the first case, the image is
divided in blocks which are collected according to zig-zag scan. In
the second one, we apply the Fast Cosine Transform to the image,
and then the transformed image is divided in blocks which are
collected according to zig-zag scan too. Later, in both cases, the
Karhunen-Loève transform is applied to mentioned blocks. On the
other hand, we present three new metrics based on eigenvalues for a
better comparative evaluation of the techniques. Simulations show
that the combined version is the best, with minor Mean Absolute
Error (MAE) and Mean Squared Error (MSE), higher Peak Signal to
Noise Ratio (PSNR) and better image quality. Finally, new technique
was far superior to JPEG and JPEG2000.
Abstract: Delayed wound healing in diabetes is primarily
associated with hyperglycemia, over-expression of inflammatory
marker, oxidative stress and delayed collagen synthesis. This
unmanaged wound is producing high economic burden on the
society. Thus research is required to develop new and effective
treatment strategies to deal with this emerging issue. Our present
study incorporates the evaluation of wound healing effects of 50%
ethanol extract of Ocimum sanctum (OSE) in streptozotocin
(45mg/kg)-induced diabetic rats with concurrent wound ulcer. The
animals showing diabetes (Blood glucose level >140 and
Abstract: This paper deals with a novel technique for the
fabrication of Spiral grooves in a dynamic thrust bearing. The main
scheme proposed in this paper is to fabricate the microgrooves using
desktop forming system. This process has advantages compared to the
conventional electro-chemical machining in the viewpoint of a higher
productivity. For this reason, a new testing apparatus is designed and
built for press forming microgrooves on a surface of the thrust bearing.
The material used in this study is sintered Cu-Fe alloy. The effects of
the forming load on the performance of micro press forming are
experimentally investigated. From the experimental results, formed
depths are closed to the target ones with increasing the forming load.
Abstract: Cement stabilization has been widely used for
improving the strength and stiffness of soft clayey soils. Cement
treated soil specimens used to investigate the stress-strain behaviour in
the laboratory study are usually cured for 7 days. This paper examines
the effects of curing time on the strength and stress strain behaviour of
cement treated marine clay under triaxial loading condition.
Laboratory-prepared cement treated Singapore marine clay with
different mix proportion S-C-W (soil solid-cement solid-water) and
curing time (7 days to 180 days) was investigated through conducting
unconfined compressive strength test and triaxial test. The results
show that the curing time has a significant effect on the unconfined
compressive strength u q , isotropic compression behaviour and stress
strain behaviour. Although the primary yield loci of the cement treated
soil specimens with the same mix proportion expand with curing time,
they are very narrowly banded and have nearly the same shape after
being normalized by isotropic compression primary stress '
py p . The
isotropic compression primary yield stress '
py p was shown to be
linearly related to unconfined compressive strength u q for specimens
with different curing time and mix proportion. The effect of curing
time on the hardening behaviour will diminish with consolidation
stress higher than isotropic compression primary yield stress but its
damping rate is dependent on the cement content.
Abstract: In this paper, Selective Adaptive Parallel Interference Cancellation (SA-PIC) technique is presented for Multicarrier Direct Sequence Code Division Multiple Access (MC DS-CDMA) scheme. The motivation of using SA-PIC is that it gives high performance and at the same time, reduces the computational complexity required to perform interference cancellation. An upper bound expression of the bit error rate (BER) for the SA-PIC under Rayleigh fading channel condition is derived. Moreover, the implementation complexities for SA-PIC and Adaptive Parallel Interference Cancellation (APIC) are discussed and compared. The performance of SA-PIC is investigated analytically and validated via computer simulations.
Abstract: Sedimentation in reservoirs and the corresponding
loss of storage capacity is one of the most serious problems in dam
engineering. Pressurized flushing, a way to remove sediments from the reservoir, is flushing under a pressurized flow condition and
nearly constant water level. Pressurized flushing has only local
effects around the outlet. Sediment in the vicinity of the outlet openings is scoured and a funnel shaped crater is created. In this study, the temporal development of flushing cone under various
hydraulic conditions was studied experimentally. Time variations of
parameters such as maximum length and width of flushing and also
depth of scouring cone was measured. Results indicated that an
increase in flow velocity (and consequently in Froude number)
established new hydraulically conditions for flushing mechanism and
so a sudden growth was observed in the amount of sediment released
and also scouring dimenssions. In addition, a set of nondimensional
relationships were identified for temporal variations of flushing scour
dimenssions, which can eventuallt be used to estimate the development of flushing cone.
Abstract: Fermented beverages have high expression in the
market for beverages in general, is increasingly valued in situations
where the characteristic aroma and flavor of the material that gave
rise to them are kept after processing. This study aimed to develop a
distilled beverage from passion fruit, and assess, by sensory tests and
chromatographic profile, the influence of different treatments (FM1-
spirit with pulp addiction and FM2 – spirit with bigger ratio of pulp
in must) in the setting of volatiles in the fruit drink, and performing
chemical characterization taking into account the main parameters of
quality established by the legislation. The chromatograms and the
first sensorial tests had indicated that sample FM1 possess better
characteristics of aroma, as much of how much quantitative the
qualitative point of view. However, it analyzes it sensorial end
(preference test) disclosed the biggest preference of the cloth provers
for sample FM2-2 (note 7.93), being the attributes of decisive color
and flavor in this reply, confirmed for the observed values lowest of
fixed and total acidity in the samples of treatment FM2.
Abstract: In order to calculate the flexural strength of
normal-strength concrete (NSC) beams, the nonlinear actual concrete
stress distribution within the compression zone is normally replaced
by an equivalent rectangular stress block, with two coefficients of α
and β to regulate the intensity and depth of the equivalent stress
respectively. For NSC beams design, α and β are usually assumed
constant as 0.85 and 0.80 in reinforced concrete (RC) codes. From an
earlier investigation of the authors, α is not a constant but significantly
affected by flexural strain gradient, and increases with the increasing
of strain gradient till a maximum value. It indicates that larger
concrete stress can be developed in flexure than that stipulated by
design codes. As an extension and application of the authors- previous
study, the modified equivalent concrete stress block is used here to
produce a series of design charts showing the maximum design limits
of flexural strength and ductility of singly- and doubly- NSC beams,
through which both strength and ductility design limits are improved
by taking into account strain gradient effect.
Abstract: We consider the development of an eight order Adam-s
type method, with A-stability property discussed by expressing them
as a one-step method in higher dimension. This makes it suitable
for solving variety of initial-value problems. The main method and
additional methods are obtained from the same continuous scheme
derived via interpolation and collocation procedures. The methods
are then applied in block form as simultaneous numerical integrators
over non-overlapping intervals. Numerical results obtained using the
proposed block form reveals that it is highly competitive with existing
methods in the literature.