Abstract: An unconventional composite inorganic ceramic
membrane capable of enhancing carbon dioxide emission decline was
fabricated and tested at laboratory scale in conformism to various
environmental guidelines and also to mitigate the effect of global
warming. A review of the existing membrane technologies for carbon
capture including the relevant gas transport mechanisms is presented.
Single gas permeation experiments using silica modified ceramic
membrane with internal diameter 20mm, outside diameter 25mm and
length of 368mm deposited on a macro porous support was carried
out to investigate individual gas permeation behaviours at different
pressures at room temperature. Membrane fabrication was achieved
using after a dip coating method. Nitrogen, Carbon dioxide, Argon,
Oxygen and Methane pure gases were used to investigate their
individual permeation rates at various pressures. Results show that
the gas flow rate increases with pressure drop. However above a
pressure of 3bar, CO2 permeability ratio to that of the other gases
indicated control of a more selective surface adsorptive transport
mechanism.
Abstract: Polymer Electrolyte Membrane Fuel Cell (PEMFC) is
such a time-vary nonlinear dynamic system. The traditional linear
modeling approach is hard to estimate structure correctly of PEMFC
system. From this reason, this paper presents a nonlinear modeling of
the PEMFC using Neural Network Auto-regressive model with
eXogenous inputs (NNARX) approach. The multilayer perception
(MLP) network is applied to evaluate the structure of the NNARX
model of PEMFC. The validity and accuracy of NNARX model are
tested by one step ahead relating output voltage to input current from
measured experimental of PEMFC. The results show that the obtained
nonlinear NNARX model can efficiently approximate the dynamic
mode of the PEMFC and model output and system measured output
consistently.
Abstract: This work is the first dowel in a rather wide research
activity in collaboration with Euro Mediterranean Center for Climate
Changes, aimed at introducing scalable approaches in Ocean
Circulation Models. We discuss designing and implementation of
a parallel algorithm for solving the Variational Data Assimilation
(DA) problem on Graphics Processing Units (GPUs). The algorithm
is based on the fully scalable 3DVar DA model, previously proposed
by the authors, which uses a Domain Decomposition approach
(we refer to this model as the DD-DA model). We proceed with
an incremental porting process consisting of 3 distinct stages:
requirements and source code analysis, incremental development of
CUDA kernels, testing and optimization. Experiments confirm the
theoretic performance analysis based on the so-called scale up factor
demonstrating that the DD-DA model can be suitably mapped on
GPU architectures.
Abstract: Latin hypercube designs (LHDs) have been applied in
many computer experiments among the space-filling designs found in
the literature. A LHD can be randomly generated but a randomly
chosen LHD may have bad properties and thus act poorly in
estimation and prediction. There is a connection between Latin
squares and orthogonal arrays (OAs). A Latin square of order s
involves an arrangement of s symbols in s rows and s columns, such
that every symbol occurs once in each row and once in each column
and this exists for every non-negative integer s. In this paper, a
computer program was written to construct orthogonal array-based
Latin hypercube designs (OA-LHDs). Orthogonal arrays (OAs) were
constructed from Latin square of order s and the OAs constructed
were afterward used to construct the desired Latin hypercube designs
for three input variables for use in computer experiments. The LHDs
constructed have better space-filling properties and they can be used
in computer experiments that involve only three input factors.
MATLAB 2012a computer package (www.mathworks.com/) was
used for the development of the program that constructs the designs.
Abstract: One of the main challenges in using the Discrete
Element Method (DEM) is to specify the correct input parameter
values. In general, the models are sensitive to the input parameter
values and accurate results can only be achieved if the correct values
are specified. For the linear contact model, micro-parameters such as
the particle density, stiffness, coefficient of friction, as well as the
particle size and shape distributions are required. There is a need for
a procedure to accurately calibrate these parameters before any
attempt can be made to accurately model a complete bulk materials
handling system. Since DEM is often used to model applications in
the mining and quarrying industries, a calibration procedure was
developed for materials that consist of relatively large (up to 40 mm
in size) particles. A coarse crushed aggregate was used as the test
material. Using a specially designed large shear box with a diameter
of 590 mm, the confined Young’s modulus (bulk stiffness) and
internal friction angle of the material were measured by means of the
confined compression test and the direct shear test respectively. DEM
models of the experimental setup were developed and the input
parameter values were varied iteratively until a close correlation
between the experimental and numerical results was achieved. The
calibration process was validated by modelling the pull-out of an
anchor from a bed of material. The model results compared well with
experimental measurement.
Abstract: An experimental and analytical research on shear
buckling of a comparably large polymer composite I-section is
presented. It is known that shear buckling load of a large span
composite beam is difficult to determine experimentally. In order to
sensitively detect shear buckling of the tested I-section, twenty strain
rosettes and eight displacement sensors were applied and attached on
the web and flange surfaces. The tested specimen was a pultruded
composite beam made of vinylester resin, E-glass, carbon fibers and
micro-fillers. Various coupon tests were performed before the shear
buckling test to obtain fundamental material properties of the Isection.
An asymmetric four-point bending loading scheme was
utilized for the shear test. The loading scheme resulted in a high shear
and almost zero moment condition at the center of the web panel. The
shear buckling load was successfully determined after analyzing the
obtained test data from strain rosettes and displacement sensors. An
analytical approach was also performed to verify the experimental
results and to support the discussed experimental program.
Abstract: This paper investigates the benefits of deliberately
unbalancing both operation time means (MTs) and unreliability
(failure and repair rates) for non-automated production lines. The
lines were simulated with various line lengths, buffer capacities,
degrees of imbalance and patterns of MT and unreliability imbalance.
Data on two performance measures, namely throughput (TR) and
average buffer level (ABL) were gathered, analyzed and compared to
a balanced line counterpart. A number of conclusions were made
with respect to the ranking of configurations, as well as to the
relationships among the independent design parameters and the
dependent variables. It was found that the best configurations are a
balanced line arrangement and a monotone decreasing MT order,
coupled with either a decreasing or a bowl unreliability configuration,
with the first generally resulting in a reduced TR and the second
leading to a lower ABL than those of a balanced line.
Abstract: During the post-Civil War era, the city of Nashville,
Tennessee, had the highest mortality rate in the United States. The
elevated death and disease rates among former slaves were
attributable to lack of quality healthcare. To address the paucity of
healthcare services, Meharry Medical College, an institution with the
mission of educating minority professionals and serving the
underserved population, was established in 1876.
Purpose: The social ecological framework and partial least squares
(PLS) path modeling were used to quantify the impact of
socioeconomic status and adverse health outcome on primary care
professionals serving the disadvantaged community. Thus, the study
results could demonstrate the accomplishment of the College’s
mission of training primary care professionals to serve in underserved
areas.
Methods: Various statistical methods were used to analyze alumni
data from 1975 – 2013. K-means cluster analysis was utilized to
identify individual medical and dental graduates in the cluster groups
of the practice communities (Disadvantaged or Non-disadvantaged
Communities). Discriminant analysis was implemented to verify the
classification accuracy of cluster analysis. The independent t-test was
performed to detect the significant mean differences of respective
clustering and criterion variables. Chi-square test was used to test if
the proportions of primary care and non-primary care specialists are
consistent with those of medical and dental graduates practicing in
the designated community clusters. Finally, the PLS path model was
constructed to explore the construct validity of analytic model by
providing the magnitude effects of socioeconomic status and adverse
health outcome on primary care professionals serving the
disadvantaged community.
Results: Approximately 83% (3,192/3,864) of Meharry Medical
College’s medical and dental graduates from 1975 to 2013 were
practicing in disadvantaged communities. Independent t-test confirmed the content validity of the cluster analysis model. Also, the
PLS path modeling demonstrated that alumni served as primary care
professionals in communities with significantly lower socioeconomic
status and higher adverse health outcome (p < .001). The PLS path
modeling exhibited the meaningful interrelation between primary
care professionals practicing communities and surrounding
environments (socioeconomic statues and adverse health outcome),
which yielded model reliability, validity, and applicability.
Conclusion: This study applied social ecological theory and
analytic modeling approaches to assess the attainment of Meharry
Medical College’s mission of training primary care professionals to
serve in underserved areas, particularly in communities with low
socioeconomic status and high rates of adverse health outcomes. In
summary, the majority of medical and dental graduates from Meharry
Medical College provided primary care services to disadvantaged
communities with low socioeconomic status and high adverse health
outcome, which demonstrated that Meharry Medical College has
fulfilled its mission. The high reliability, validity, and applicability of
this model imply that it could be replicated for comparable
universities and colleges elsewhere.
Abstract: Introduction: There are multiple social, individual and
cultural factors that influence an individual’s decision to adopt family
planning methods especially among non-users in patriarchal societies
like Pakistan. Non-users, if targeted efficiently, can contribute
significantly to country’s CPR. A research study showed that nonusers
if convinced to adopt lactational amenorrhea method can shift
to long term methods in future. Research shows that if non users are
targeted efficiently a 59% reduction in unintended pregnancies in
Saharan Africa and South-Central and South-East Asia is anticipated.
Methods: We did secondary data analysis on Pakistan
Demographic Heath Survey (2012-13) dataset. Use of contraception
(never-use/ever-use) was the outcome variable. At univariate level
Chi-square/Fisher Exact test was used to assess relationship of
baseline covariates with contraception use. Then variables to be
incorporated in the model were checked for multicollinearity,
confounding and interaction. Then binary logistic regression (with an
urban-rural stratification) was done to find relationship between
contraception use and baseline demographic and social variables.
Results: The multivariate analyses of the study showed that
younger women (≤ 29 years)were more prone to be never users as
compared to those who were >30 years and this trend was seen in
urban areas (AOR 1.92, CI 1.453-2.536) as well as rural areas (AOR
1.809, CI 1.421-2.303). While looking at regional variation, women
from urban Sindh (AOR 1.548, CI 1.142-2.099) and urban
Balochistan (AOR 2.403, CI 1.504-3.839) had more never users as
compared to other urban regions. Women in the rich wealth quintile
were more never users and this was seen both in urban and rural
localities (urban (AOR 1.106 CI .753-1.624); rural areas (AOR 1.162,
CI .887-1.524)) even though these were not statistically significant.
Women idealizing more children (>4) are more never users as
compared to those idealizing less children in both urban (AOR 1.854,
CI 1.275-2.697) and rural areas (AOR 2.101, CI 1.514-2.916).
Women who never lost a pregnancy were more inclined to be nonusers
in rural areas (AOR 1.394, CI 1.127-1.723) .Women familiar
with only traditional or no method had more never users in rural areas
(AOR 1.717, CI 1.127-1.723) but in urban areas it wasn’t significant.
Women unaware of Lady Health Worker’s presence in their area
were more never users especially in rural areas (AOR 1.276, CI
1.014-1.607). Women who did not visit any care provider were more
never users (urban (AOR 11.738, CI 9.112-15.121) rural areas (AOR
7.832, CI 6.243-9.826)).
Discussion/Conclusion: This study concluded that government,
policy makers and private sector family planning programs should
focus on the untapped pool of never users (younger women from underserved provinces, in higher wealth quintiles, who desire more
children.). We need to make sure to cover catchment areas where
there are less LHWs and less providers as ignorance to modern
methods and never been visited by an LHW are important
determinants of never use. This all is in sync with previous literate
from similar developing countries.
Abstract: This study attempts to identify the factors influencing
on women empowerment of rural area in Sri Lanka through micro
finance services. Data were collected from one hundred (100) rural
women involving self-employment activities through a questionnaire
using direct personal interviews. Judgment and Convenience Random
sampling technique was used to select the sample size from three
Divisional Secretariat divisions of Kandawalai, Poonakari and
Karachchi in Kilinochchi District. The factor analysis was performed
on fourteen (14) variables for screening and reducing the variables to
identify the influencing factors on empowerment. Multiple regression
analysis was used to identify the relationship between the three
empowerment factors and the impact of micro finance on overall
empowerment of rural women. The result of this study summarized
the variables into three factors namely decision making, freedom to
mobility and family support and which are positively associated with
empowerment. In addition to this the value of adjusted R2 is 0.248
indicates that all the variables extracted can be explained 24.8% of
the variation in the women empowerment through microfinance.
Independent variables of these three factors have positive correlation
with women empowerment as well as significant values at 5 percent
level.
Abstract: Present study is carried out on six lane divided urban
arterial road in Patna and Pune city of India. Both the road having
distinct differences in terms of the vehicle composition and the road
side parking. Arterial road in Patan city has 33% of non-motorized
mode, whereas Pune arterial road dominated by 65% of Two wheeler.
Also road side parking is observed in Patna city. The field studies
using videography techniques are carried out for traffic data
collection. Data are extracted for one minute duration for vehicle
composition, speed variation and flow rate on selected arterial road of
the two cities. Speed flow relationship is developed and capacity is
determine. Equivalency factor in terms of dynamic car unit is
determine to represent the vehicle is single unit. The variation in the
capacity due to side friction, presence of non motorized traffic and
effective utilization of lane width is compared at concluding remarks.
Abstract: Moringa oleifera is a nutritious vegetable tree with
varieties of potential uses, as almost every part of the Moringa
oleifera tree can be used for food. This study was conducted in Oyo
State, Nigeria, to find out the level of acceptability of Moringa
oleifera diversified products among rural and urban dwellers.
Purposive sampling was used to select two local governments’ areas.
Stratified sampling technique was also used to select one community
each from rural and urban areas while snowball sampling technique
was used to select ten respondents each from the two communities,
making a total number of forty respondents. Data were analyzed
using frequencies, percentages, Chi-square, Pearson Product Moment
Correlation and regression analysis. Result from the study revealed
that majority of the respondents (80%) fell within the age range of
20-49 years and 55% of them were male, 55% were married, 70% of
them were Christians, 80% of them had tertiary education. The result
also showed that 85% were aware of the Moringa plant and (65%) of
them have consumed Moringa oleifera and the perception statements
on the benefits of Moringa oleifera indicated that (52.5%) of the
respondents rated Moringa oleifera to be favorable, most of them had
high acceptability for Moringa egusi soup, Moringa tea, Moringa pap
and yam pottage with Moringa. The result of the hypotheses testing
showed that there is a significant relationship between sex of the
respondents and acceptability of the diversified Moringa oleifera
products (x2=6.465, p = 0.011). There is also a significant
relationship between family size of the respondents level of
acceptability of the Moringa oleifera products (r = 0.327, p = 0.040).
Based on the level of acceptability of Moringa oleifera diversified
products; the plant is of great economic importance to the populace.
Therefore, there should be more public awareness through the media
to enlighten people on the beneficial effects of Moringa oleifera.
Abstract: The past two decades, Thailand faced the natural
disasters, for instance, Gay typhoon in 1989, tsunami in 2004, and
huge flood in 2011. The disaster management in Thailand was
improved both structure and mechanism for cope with the natural
disaster since 2007. However, the natural disaster management in
Thailand has various problems, for examples, cooperation between
related an organizations have not unity, inadequate resources, the
natural disaster management of public sectors not proactive, people
has not awareness the risk of the natural disaster, and communities
did not participate in the natural disaster management.
Objective of this study is to find the methods for capacity building
in the natural disaster management of Thailand. The concept and
information about the capacity building and the natural disaster
management of Thailand were reviewed and analyzed by classifying
and organizing data. The result found that the methods for capacity
building in the natural disaster management of Thailand should be
consist of 1) link operation and information in the natural disaster
management between nation, province, local and community levels,
2) enhance competency and resources of public sectors which relate
to the natural disaster management, 3) establish proactive natural
disaster management both planning and implementation, 4)
decentralize the natural disaster management to local government
organizations, 5) construct public awareness in the natural disaster
management to community, 6) support Community Based Disaster
Risk Management (CBDRM) seriously, and 7) emphasis on
participation in the natural disaster management of all stakeholders.
Abstract: High pressure turbine (HPT) blades of DV – 2 jet
engines are made from Ni – based superalloy. This alloy was
originally manufactured in the Soviet Union and referred as ŽS6K.
For improving alloy’s high temperature resistance are blades coated
with Al – Si diffusion layer. A regular operation temperature of HPT
blades vary from 705°C to 750°C depending on jet engine regime.
An overcrossing working temperature range causes degradation of
the protective coating as well as base material which microstructure
is formed by the gamma matrix and strengthening phase gamma
prime (forming small particles in the microstructure). Diffusion
processes inside the material during exposition of the material to high
temperatures causes mainly coarsening of the gamma prime particles,
thus decreasing its strengthening effect. Degradation of the Al – Si
coating caused its thickness growth. All the microstructure changes
and coating layer thickness growth results in decreasing of the turbine
blade operation lifetime.
Abstract: In the past few years, the amount of malicious software
increased exponentially and, therefore, machine learning algorithms
became instrumental in identifying clean and malware files through
(semi)-automated classification. When working with very large
datasets, the major challenge is to reach both a very high malware
detection rate and a very low false positive rate. Another challenge
is to minimize the time needed for the machine learning algorithm to
do so. This paper presents a comparative study between different
machine learning techniques such as linear classifiers, ensembles,
decision trees or various hybrids thereof. The training dataset consists
of approximately 2 million clean files and 200.000 infected files,
which is a realistic quantitative mixture. The paper investigates the
above mentioned methods with respect to both their performance
(detection rate and false positive rate) and their practicability.
Abstract: The objective of present research paper is to highlight
the importance of measuring advertisement effectiveness in print
media and to develop a conceptual model for advertisement
effectiveness. The developed model is based on dimensions on which
advertisement effectiveness depends and on the dimensions which are
used to measure the effectiveness. An in-depth and extensive
literature review is carried out to understand the concept of
advertisement effectiveness and its various determinants in context of
print media. Based on the insights gained, a conceptual framework
for advertisement effectiveness is presented. The model is an attempt
to uncover the relatively less explored area of advertisement
effectiveness in Indian advertising scenario. It is believed that present
work will encourage scholars and academicians to further explore the
area and will offer conceptual assistance and a fresh direction in the
domain of advertisement effectiveness.
Abstract: Proposed paper dealt with the modelling and analysis of induction motor based on the mathematical expression using the graphical programming environment of Laboratory Virtual Instrument Engineering Workbench (LabVIEW). Induction motor modelling with the mathematical expression enables the motor to be simulated with the various required parameters. Owing to the invention of variable speed drives study about the induction motor characteristics became complex. In this simulation motor internal parameter such as stator resistance and reactance, rotor resistance and reactance, phase voltage, frequency and losses will be given as input. By varying the speed of motor corresponding parameters can be obtained they are input power, output power, efficiency, torque induced, slip and current.
Abstract: Non contact evaluation of the thickness of paint
coatings can be attempted by different destructive and nondestructive
methods such as cross-section microscopy, gravimetric mass
measurement, magnetic gauges, Eddy current, ultrasound or
terahertz. Infrared thermography is a nondestructive and non-invasive
method that can be envisaged as a useful tool to measure the surface
thickness variations by analyzing the temperature response. In this
paper, the thermal quadrupole method for two layered samples heated
up with a pulsed excitation is firstly used. By analyzing the thermal
responses as a function of thermal properties and thicknesses of both
layers, optimal parameters for the excitation source can be identified.
Simulations show that a pulsed excitation with duration of ten
milliseconds allows obtaining a substrate-independent thermal
response. Based on this result, an experimental setup consisting of a
near-infrared laser diode and an Infrared camera was next used to
evaluate the variation of paint coating thickness between 60 μm and
130 μm on two samples. Results show that the parameters extracted
for thermal images are correlated with the estimated thicknesses by
the Eddy current methods. The laser pulsed thermography is thus an
interesting alternative nondestructive method that can be moreover
used for nonconductive substrates.
Abstract: The paper presents a method for a simple and
immediate motion planning of a SCARA robot, whose end-effector
has to move along a given trajectory; the calculation procedure
requires the user to define in analytical form or by points the
trajectory to be followed and to assign the curvilinear abscissa as
function of the time. On the basis of the geometrical characteristics
of the robot, a specifically developed program determines the motion
laws of the actuators that enable the robot to generate the required
movement; this software can be used in all industrial applications for
which a SCARA robot has to be frequently reprogrammed, in order
to generate various types of trajectories with different motion times.
Abstract: We proposed a Hyperbolic Gompertz Growth Model
(HGGM), which was developed by introducing a shape parameter
(allometric). This was achieved by convoluting hyperbolic sine
function on the intrinsic rate of growth in the classical gompertz
growth equation. The resulting integral solution obtained
deterministically was reprogrammed into a statistical model and used
in modeling the height and diameter of Pines (Pinus caribaea). Its
ability in model prediction was compared with the classical gompertz
growth model, an approach which mimicked the natural variability of
height/diameter increment with respect to age and therefore provides
a more realistic height/diameter predictions using goodness of fit
tests and model selection criteria. The Kolmogorov Smirnov test and
Shapiro-Wilk test was also used to test the compliance of the error
term to normality assumptions while the independence of the error
term was confirmed using the runs test. The mean function of top
height/Dbh over age using the two models under study predicted
closely the observed values of top height/Dbh in the hyperbolic
gompertz growth models better than the source model (classical
gompertz growth model) while the results of R2, Adj. R2, MSE and
AIC confirmed the predictive power of the Hyperbolic Gompertz
growth models over its source model.