Abstract: Experimental studies to investigate the depth of the
scour conducted at a side-weir intersection located at the 1800 curved
flume which located Hydraulic Laboratory of Yıldız Technical
University, Istanbul, Turkey. Side weirs were located at the middle of
the straight part of the main channel. Three different lengths (25, 40
and 50 cm) and three different weir crest height (7, 10 and 12 cm) of
the side weir placed on the side weir station. There is no scour when
the material is only kaolin. Therefore, the cohesive bed was prepared
by properly mixing clay material (kaolin) with 31% sand in all
experiments. Following 24h consolidation time, in order to observe
the effect of flow intensity on the scour depth, experiments were
carried out for five different upstream Froude numbers in the range of
0.33-0.81.
As a result of this study the relation between scour depth and
upstream flow intensity as a function of time have been established.
The longitudinal velocities decreased along the side weir; towards the
downstream due to overflow over the side-weirs. At the beginning,
the scour depth increases rapidly with time and then asymptotically
approached constant values in all experiments for all side weir
dimensions as in non-cohesive sediment. Thus, the scour depth
reached equilibrium conditions. Time to equilibrium depends on the
approach flow intensity and the dimensions of side weirs. For
different heights of the weir crest, dimensionless scour depths
increased with increasing upstream Froude number. Equilibrium
scour depths which formed 7 cm side-weir crest height were obtained
higher than that of the 12 cm side-weir crest height. This means when
side-weir crest height increased equilibrium scour depths decreased.
Although the upstream side of the scour hole is almost vertical, the
downstream side of the hole is inclined.
Abstract: Al6061 alloy base matrix, reinforced with particles of
silicon carbide (10 wt %) and Graphite powder (1wt%), known as
hybrid composites have been fabricated by liquid metallurgy route
(stir casting technique) and optimized at different parameters like
applied load, sliding speed and sliding distance by taguchi method. A
plan of experiment generated through taguchi technique was used to
perform experiments based on L27 orthogonal array. The developed
ANOVA and regression equations are used to find the optimum
coefficient of friction and wear under the influence of applied load,
sliding speed and sliding distance. On the basis of “smaller the best”
the dry sliding wear resistance was analysed and finally confirmation
tests were carried out to verify the experimental results.
Abstract: Purpose: The study aimed to assess the depressant or
antidepressant effects of several Nonsteroidal Anti-Inflammatory
Drugs (NSAIDs) in mice: the selective cyclooxygenase-2 (COX-2)
inhibitor meloxicam, and the non-selective COX-1 and COX-2
inhibitors lornoxicam, sodium metamizole, and ketorolac. The
current literature data regarding such effects of these agents are
scarce.
Materials and methods: The study was carried out on NMRI mice
weighing 20-35 g, kept in a standard laboratory environment. The
study was approved by the Ethics Committee of the University of
Medicine and Pharmacy „Carol Davila”, Bucharest. The study agents
were injected intraperitoneally, 10 mL/kg body weight (bw) 1 hour
before the assessment of the locomotor activity by cage testing (n=10
mice/ group) and 2 hours before the forced swimming tests (n=15).
The study agents were dissolved in normal saline (meloxicam,
sodium metamizole), ethanol 11.8% v/v in normal saline (ketorolac),
or water (lornoxicam), respectively. Negative and positive control
agents were also given (amitryptilline in the forced swimming test).
The cage floor used in the locomotor activity assessment was divided
into 20 equal 10 cm squares. The forced swimming test involved
partial immersion of the mice in cylinders (15/9cm height/diameter)
filled with water (10 cm depth at 28C), where they were left for 6
minutes. The cage endpoint used in the locomotor activity assessment
was the number of treaded squares. Four endpoints were used in the
forced swimming test (immobility latency for the entire 6 minutes,
and immobility, swimming, and climbing scores for the final 4
minutes of the swimming session), recorded by an observer that was
„blinded” to the experimental design. The statistical analysis used the
Levene test for variance homogeneity, ANOVA and post-hoc
analysis as appropriate, Tukey or Tamhane tests.
Results: No statistically significant increase or decrease in the
number of treaded squares was seen in the locomotor activity
assessment of any mice group. In the forced swimming test,
amitryptilline showed an antidepressant effect in each experiment, at
the 10 mg/kg bw dosage. Sodium metamizole was depressant at 100
mg/kg bw (increased the immobility score, p=0.049, Tamhane test),
but not in lower dosages as well (25 and 50 mg/kg bw). Ketorolac
showed an antidepressant effect at the intermediate dosage of 5
mg/kg bw, but not so in the dosages of 2.5 and 10 mg/kg bw,
respectively (increased the swimming score, p=0.012, Tamhane test).
Meloxicam and lornoxicam did not alter the forced swimming
endpoints at any dosage level.
Discussion: 1) Certain NSAIDs caused changes in the forced
swimming patterns without interfering with locomotion. 2) Sodium
metamizole showed a depressant effect, whereas ketorolac proved
antidepressant. Conclusion: NSAID-induced mood changes are not
class effects of these agents and apparently are independent of the
type of inhibited cyclooxygenase (COX-1 or COX-2).
Disclosure: This paper was co-financed from the European Social
Fund, through the Sectorial Operational Programme Human Resources Development 2007-2013, project number POSDRU /159
/1.5 /S /138907 "Excellence in scientific interdisciplinary research,
doctoral and postdoctoral, in the economic, social and medical fields
-EXCELIS", coordinator The Bucharest University of Economic
Studies.
Abstract: Advanced treatments such as forward osmosis (FO)
can be used to separate or reject nutrients from secondary treated
effluents. Forward osmosis uses the chemical potential across the
membrane, which is the osmotic pressure gradient, to induce water to
flow through the membrane from a feed solution (FS) into a draw
solution (DS). The performance of FO is affected by the membrane
characteristics, composition of the FS and DS, and operating
conditions. The aim of this study was to investigate the optimum
velocity and temperature for nutrient rejection and water flux
performance in FO treatments. MgCl2 was used as the DS in the FO
process. The results showed that higher cross flow velocities yielded
higher water fluxes. High rejection of nutrients was achieved by using
a moderate cross flow velocity at 0.25 m/s. Nutrient rejection was
insensitive to temperature variation, whereas water flux was
significantly impacted by it. A temperature of 25°C was found to be
good for nutrient rejection.
Abstract: The concentrations of heavy metals in sediments of
Qua Iboe River Estuary (QIRE) were monitored at four different
sampling locations in wet and dry seasons. A preliminary survey to
determine the four sampling stations along the river continuum
showed that the area spanned between
Abstract: Microstructural and hardening changes of
Fe-0.2wt.%V alloy and pure Fe irradiated with 100 keV hydrogen ions
at room temperature were investigated. It was found that dislocation
density varies dramatically after irradiation, ranging from dislocation
free to dense areas with tangled and complex dislocation
configuration. As the irradiated Fe-0.2wt.%V samples were annealed
at 773 K, the irradiation-induced dislocation loops disappear, while
many small precipitates with enriched C distribute in the matrix. Some
large precipitates with enriched V were also observed. The hardness of
Fe-0.2wt.%V alloy and pure Fe increases after irradiation, which
ascribes to the formation of dislocation loops in the irradiated
specimens. Compared with pure Fe, the size of the
irradiation-introduced dislocation loops in Fe-0.2wt.%V alloy
decreases and the density increases, the change of the hardness also
decreases.
Abstract: Dielectric ceramic samples in the BaO-Re2O3-TiO2
ternary system were synthesized with structural formula Ba2-
xRe4+2x/3Ti8O24 where Re= rare earth metal and Re= Sm and La where
x varies from 0.0 to 0.6 with step size 0.1. Polycrystalline samples
were prepared by the conventional solid state reaction technique. The
dielectric, electrical and impedance analysis of all the samples in the
frequency range 1KHz- 1MHz at room temperature (25°C) have been
done to get the understanding of electrical conduction and dielectric
relaxation and their correlation. Dielectric response of the samples at
lower frequencies shows dielectric dispersion while at higher
frequencies it shows dielectric relaxation. The ac conductivity is well
fitted by the Jonscher law. The spectroscopic data in the impedance
plane confirms the existence of grain contribution to the relaxation.
All the properties are found out to be function of frequency as well as
the amount of substitution.
Abstract: In the present study, RBF neural networks were used
for predicting the performance and emission parameters of a
biodiesel engine. Engine experiments were carried out in a 4 stroke
diesel engine using blends of diesel and Honge methyl ester as the
fuel. Performance parameters like BTE, BSEC, Tex and emissions
from the engine were measured. These experimental results were
used for ANN modeling.
RBF center initialization was done by random selection and by
using Clustered techniques. Network was trained by using fixed and
varying widths for the RBF units. It was observed that RBF results
were having a good agreement with the experimental results.
Networks trained by using clustering technique gave better results
than using random selection of centers in terms of reduced MRE and
increased prediction accuracy. The average MRE for the performance
parameters was 3.25% with the prediction accuracy of 98% and for
emissions it was 10.4% with a prediction accuracy of 80%.
Abstract: To understand the friction stir welding process, it is
very important to know the nature of the material flow in and around
the tool. The process is a combination of both thermal as well as
mechanical work i.e. it is a coupled thermo-mechanical process.
Numerical simulations are very much essential in order to obtain a
complete knowledge of the process as well as the physics underlying
it. In the present work a model based approach is adopted in order to
study material flow. A thermo-mechanical based CFD model is
developed using a Finite Element package, Comsol Multiphysics.
The fluid flow analysis is done. The model simultaneously predicts
shear strain fields, shear strain rates and shear stress over the entire
workpiece for the given conditions. The flow fields generated by the
streamline plot give an idea of the material flow. The variation of
dynamic viscosity, velocity field and shear strain fields with various
welding parameters is studied. Finally the result obtained from the
above mentioned conditions is discussed elaborately and concluded.
Abstract: This paper presents a rank correlation curve. The
traditional correlation coefficient is valid for both continuous
variables and for integer variables using rank statistics. Since
the correlation coefficient has already been established in rank
statistics by Spearman, such a calculation can be extended to
the correlation curve.
This paper presents two survey questions. The survey
collected non-continuous variables. We will show weak to
moderate correlation. Obviously, one question has a negative
effect on the other. A review of the qualitative literature
can answer which question and why. The rank correlation
curve shows which collection of responses has a positive
slope and which collection of responses has a negative slope.
Such information is unavailable from the flat, ”first-glance”
correlation statistics.
Abstract: Quantitative radiobiological models can be used to
assess the optimum clinical outcome from sophisticated therapeutic
modalities by calculating tumor control probability (TCP) and normal
tissue complication probability (NTCP). In this study two 3D-CRT
and an IMRT treatment plans were developed with an initial
prescription dose of 60 Gy in 2 Gy/fraction to prostate. Sensitivity of
TCP and Complication free tumor control probability (P+) to the
different values of α/β ratio was investigated for various prescription
doses planned to be delivered in either a fixed number of fractions (I)
or in a fixed dose per fraction (II) in each of the three different
treatment plans. High dose/fraction and high α/β value result in
comparatively smaller P+ and IMRT plans resulted in the highest P+,
mainly due to the decrease in NTCP. If α/β is lower than expected,
better tumor control can be achieved by increasing dose/fraction but
decreasing the number of fractions.
Abstract: In this research article of modeling Underwater
Wireless Sensor Network Simulators, we provide a comprehensive
overview of the various currently available simulators used in UWSN
modeling. In this work, we compare their working environment,
software platform, simulation language, key features, limitations and
corresponding applications. Based on extensive experimentation and
performance analysis, we provide their efficiency for specific
applications. We have also provided guidelines for developing
protocols in different layers of the protocol stack, and finally these
parameters are also compared and tabulated. This analysis is
significant for researchers and designers to find the right simulator
for their research activities.
Abstract: The posterior reference for the ala tragal line is a
cause of confusion, with different authors suggesting different
locations as to the superior, middle or inferior part of the tragus. This
study was conducted on 200 subjects to evaluate if any correlation
exists between the variation of angulation of palatal throat form and
the relative parallelism of occlusal plane to ala-tragal line at different
tragal levels. A custom made Occlusal Plane Analyzer was used to
check the parallelism between the ala-tragal line and occlusal plane.
A lateral cephalogram was shot for each subject to measure the
angulation of the palatal throat form. Fisher’s exact test was used to
evaluate the correlation between the angulation of the palatal throat
form and the relative parallelism of occlusal plane to the ala tragal
line. Also, a classification was formulated for the palatal throat form,
based on confidence interval. From the results of the study, the
inferior part, middle part and superior part of the tragus were seen as
the reference points in 49.5%, 32% and 18.5% of the subjects
respectively. Class I palatal throat form (41degree-50 degree), Class
II palatal throat form (below 41 degree) and Class III palatal throat
form (above 50 degree) were seen in 42%, 43% and 15% of the
subjects respectively. It was also concluded that there is no
significant correlation between the variation in the angulations of the
palatal throat form and the relative parallelism of occlusal plane to
the ala-tragal line.
Abstract: We propose new multiple-channel piezoelectric (PZT)
actuated tunable optical filter based on racetrack multi-ring
resonators for wavelength de-multiplexing network applications. We
design tunable eight-channel wavelength de-multiplexer consisting of
eight cascaded PZT actuated tunable multi-ring resonator filter with a
channel spacing of 1.6nm. The filter for each channel is basically
structured on a suspended beam, sandwiched with piezoelectric
material and built in integrated ring resonators which are placed on
the middle of the beam to gain uniform stress and linearly varying
longitudinal strain. A reference single mode serially coupled multi
stage racetrack ring resonator with the same radii and coupling length
is designed with a line width of 0.8974nm with a flat top pass band at
1dB of 0.5205nm and free spectral range of about 14.9nm. In each
channel, a small change in the perimeter of the rings is introduced to
establish the shift in resonance wavelength as per the defined channel
spacing. As a result, when a DC voltage is applied, the beams will
elongate, which involves mechanical deformation of the ring
resonators that induces a stress and a strain, which brings a change in
refractive index and perimeter of the rings leading to change in the
output spectrum shift providing the tunability of central wavelength
in each channel. Simultaneous wave length shift as high as
45.54pm/
Abstract: In wastewater treatment processes, aeration introduces
air into a liquid. In these systems, air is introduced by different
devices submerged in the wastewater. Smaller bubbles result in more
bubble surface area per unit of volume and higher oxygen transfer
efficiency. Jet pumps are devices that use air bubbles and are widely
used in wastewater treatment processes. The principle of jet pumps is
their ability to transfer energy of one fluid, called primary or motive,
into a secondary fluid or gas. These pumps have no moving parts and
are able to work in remote areas under extreme conditions. The
objective of this work is to study experimentally the characteristics of
the jet pump and the size of air bubbles in the laboratory water tank.
The effect of flow rate ratio on pump performance is investigated in
order to have a better understanding about pump behavior under
various conditions, in order to determine the efficiency of receiving
air bubbles different sizes. The experiments show that we should take
care when increasing the flow rate ratio while seeking to decrease
bubble size in the outlet flow. This study will help improve and
extend the use of the jet pump in many practical applications.
Abstract: A field study was conducted to evaluate the efficacy of
safflower plant for phytoremediation of contaminated soils. The
experiment was performed on an agricultural fields contaminated by
the Non-Ferrous-Metal Works near Plovdiv, Bulgaria. Field
experiments with randomized complete block design with five
treatments (control, compost amendments added at 20 and 40 t/daa,
and vermicompost amendments added at 20 and 40 t/daa) were
carried out. The quality of safflower seeds and oil (heavy metals and
fatty acid composition) were determined. Tested organic amendments
significantly influenced the chemical composition of safflower seeds
and oil. The compost and vermicompost treatments significantly
reduced heavy metals concentration in safflower seeds and oils, but
the effect differed among them. Addition of vermicompost and
compost leads to an increase in the content of palmitic acid and
linoleic acid, and a decrease in the stearic and oleic acids compared
with the control. A significant increase in the quantity of saturated
acids was observed in the variants with 20 t/daa of compost and 20
t/daa of vermicompost (9.1 and 8.9% relative to the control).
Safflower is a plant which is tolerant to heavy metals and can be
successfully used in the phytoremediation of heavy metal
contaminated soils. The processing of seeds to oil and using the
obtained oil for nutritional purposes will greatly reduce the cost of
phytoremediation.
Abstract: Due to the continuous increment of the load demand,
identification of weaker buses, improvement of voltage profile and
power losses in the context of the voltage stability problems has
become one of the major concerns for the larger, complex,
interconnected power systems. The objective of this paper is to
review the impact of Flexible AC Transmission System (FACTS)
controller in Wind generators connected electrical network for
maintaining voltage stability. Wind energy could be the growing
renewable energy due to several advantages. The influence of wind
generators on power quality is a significant issue; non uniform power
production causes variations in system voltage and frequency.
Therefore, wind farm requires high reactive power compensation; the
advances in high power semiconducting devices have led to the
development of FACTS. The FACTS devices such as for example
SVC inject reactive power into the system which helps in maintaining
a better voltage profile. The performance is evaluated on an IEEE 14
bus system, two wind generators are connected at low voltage buses
to meet the increased load demand and SVC devices are integrated at
the buses with wind generators to keep voltage stability. Power
flows, nodal voltage magnitudes and angles of the power network are
obtained by iterative solutions using MIPOWER.
Abstract: Durian is the flagship fruit of Mindanao and there is
an abundance of several cultivars with many confusing identities/
names.
The project was conducted to develop procedure for reliable and
rapid detection and sorting of durian planting materials. Moreover, it
is also aimed to establish specific genetic or DNA markers for routine
testing and authentication of durian cultivars in question.
The project developed molecular procedures for routine testing.
SSR primers were also screened and identified for their utility in
discriminating durian cultivars collected.
Results of the study showed the following accomplishments:
1. Twenty (29) SSR primers were selected and identified based on
their ability to discriminate durian cultivars,
2. Optimized and established standard procedure for identification
and authentication of Durian cultivars
3. Genetic profile of durian is now available at Biotech Unit
Our results demonstrate the relevance of using molecular
techniques in evaluating and identifying durian clones. The most
polymorphic primers tested in this study could be useful tools for
detecting variation even at the early stage of the plant especially for
commercial purposes. The process developed combines the efficiency
of the microsatellites development process with the optimization of
non-radioactive detection process resulting in a user-friendly protocol
that can be performed in two (2) weeks and easily incorporated into
laboratories about to start microsatellite development projects. This
can be of great importance to extend microsatellite analyses to other
crop species where minimal genetic information is currently
available. With this, the University can now be a service laboratory
for routine testing and authentication of durian clones.
Abstract: The secondary alloy A226 is used for many
automotive casting produced by mould casting and high pressure die
casting. This alloy has excellent castability, good mechanical
properties and cost-effectiveness. Production of primary aluminium
alloys belong to heavy source fouling of life environs. The European
Union calls for the emission reduction and reduction in energy
consumption therefore increase production of recycled (secondary)
aluminium cast alloys. The contribution is deal with influence of
recycling on the quality of the casting made from A226 in automotive
industry. The properties of the casting made from secondary
aluminium alloys were compared with the required properties of
primary aluminium alloys. The effect of recycling on microstructure
was observed using combination different analytical techniques (light
microscopy upon black-white etching, scanning electron microscopy
- SEM upon deep etching and energy dispersive X-ray analysis -
EDX). These techniques were used for the identification of the
various structure parameters, which was used to compare secondary
alloy microstructure with primary alloy microstructure.
Abstract: Edge is variation of brightness in an image. Edge
detection is useful in many application areas such as finding forests,
rivers from a satellite image, detecting broken bone in a medical
image etc. The paper discusses about finding edge of multiple aerial
images in parallel. The proposed work tested on 38 images 37
colored and one monochrome image. The time taken to process N
images in parallel is equivalent to time taken to process 1 image in
sequential. Message Passing Interface (MPI) and Open Computing
Language (OpenCL) is used to achieve task and pixel level
parallelism respectively.