Abstract: New generation mobile communication networks have
the ability of supporting triple play. In order that, Orthogonal
Frequency Division Multiplexing (OFDM) access techniques have
been chosen to enlarge the system ability for high data rates
networks. Many of cross-layer modeling and optimization schemes
for Quality of Service (QoS) and capacity of downlink multiuser
OFDM system were proposed. In this paper, the Maximum Weighted
Capacity (MWC) based resource allocation at the Physical (PHY)
layer is used. This resource allocation scheme provides a much better
QoS than the previous resource allocation schemes, while
maintaining the highest or nearly highest capacity and costing similar
complexity. In addition, the Delay Satisfaction (DS) scheduling at the
Medium Access Control (MAC) layer, which allows more than one
connection to be served in each slot is used. This scheduling
technique is more efficient than conventional scheduling to
investigate both of the number of users as well as the number of
subcarriers against system capacity. The system will be optimized for
different operational environments: the outdoor deployment scenarios
as well as the indoor deployment scenarios are investigated and also
for different channel models. In addition, effective capacity approach
[1] is used not only for providing QoS for different mobile users, but
also to increase the total wireless network's throughput.
Abstract: DNA microarrays allow the measurement of expression levels for a large number of genes, perhaps all genes of an organism, within a number of different experimental samples. It is very much important to extract biologically meaningful information from this huge amount of expression data to know the current state of the cell because most cellular processes are regulated by changes in gene expression. Association rule mining techniques are helpful to find association relationship between genes. Numerous association rule mining algorithms have been developed to analyze and associate this huge amount of gene expression data. This paper focuses on some of the popular association rule mining algorithms developed to analyze gene expression data.
Abstract: Nowadays, power systems, energy generation by wind
has been very important. Noting that the production of electrical
energy by wind turbines on site to several factors (such as wind speed
and profile site for the turbines, especially off the wind input speed,
wind rated speed and wind output speed disconnect) is dependent. On
the other hand, several different types of turbines in the market there.
Therefore, selecting a turbine that its capacity could also answer the
need for electric consumers the efficiency is high something is
important and necessary. In this context, calculating the amount of
wind power to help optimize overall network, system operation, in
determining the parameters of wind power is very important.
In this article, to help calculate the amount of wind power plant,
connected to the national network in the region Manjil wind,
selecting the best type of turbine and power delivery profile
appropriate to the network using Monte Carlo method has been.
In this paper, wind speed data from the wind site in Manjil, as minute
and during the year has been. Necessary simulations based on
Random Numbers Simulation method and repeat, using the software
MATLAB and Excel has been done.
Abstract: Square pipes (pipes with square cross sections) are
being used for various industrial objectives, such as machine
structure components and housing/building elements. The utilization
of them is extending rapidly and widely. Hence, the out-put of those
pipes is increasing and new application fields are continually
developing.
Due to various demands in recent time, the products have to
satisfy difficult specifications with high accuracy in dimensions. The
reshaping process design of pipes with square cross sections;
however, is performed by trial and error and based on expert-s
experience.
In this paper, a computer-aided simulation is developed based on
the 2-D elastic-plastic method with consideration of the shear
deformation to analyze the reshaping process. Effect of various
parameters such as diameter of the circular pipe and mechanical
properties of metal on product dimension and quality can be
evaluated by using this simulation. Moreover, design of reshaping
process include determination of shrinkage of cross section,
necessary number of stands, radius of rolls and height of pipe at each
stand, are investigated. Further, it is shown that there are good
agreements between the results of the design method and the
experimental results.
Abstract: Oxyleotris marmorata is considered as
undomesticated fish, and its culture occasionally faces a problem of
food deprivation. The present study aims to evaluate alteration of
hematological indices, blood chemical associated with liver function
during 4 weeks of fasting. A non-linear relationships between fasting
days and hematological parameters (red blood cell number; y = -
0.002x2 + 0.041x + 1.249; R2=0.915, P0.05), mean corpuscular
volume; y = -0.180x2 + 2.183x + 149.61; R2=0.732, P>0.05, mean
corpuscular hemoglobin; y = -0.041x2 + 0.862x + 29.864; R2=0.818,
P>0.05 and mean corpuscular hemoglobin concentration; y = -
0.044x2 + 0.711x + 21.580; R2=0.730, P>0.05) were demonstrated.
Significant change in hematocrit (Ht) during fasting period was
observed. Ht elevated sharply increase at the first weeks of fasting
period. Higher Ht also was detected during week 2-4 of fasting time.
The significant reduction of hepatosomatic index was observed (y = -
0.007x2 - 0.096x + 1.414; R2=0.968, P0.05, serum glutamic oxaloacetic transaminase;
y = 0.005x2 – 0.201x2 + 1.297x + 33.256; R2=1, P0.05). Taken together, prolonged fasting has
deleterious effects on hematological indices, liver mass and enzyme
associated in liver function. The marked adverse effects occurred
after the first week of fasting state.
Abstract: This is an application research presenting the
improvement of production quality using the six sigma solutions and
the analyses of benefit-cost ratio. The case of interest is the
production of tile-concrete. Such production has faced with the
problem of high nonconforming products from an inappropriate
surface coating and had low process capability based on the strength
property of tile. Surface coating and tile strength are the most critical
to quality of this product. The improvements followed five stages of
six sigma solutions. After the improvement, the production yield was
improved to 80% as target required and the defective products from
coating process was remarkably reduced from 29.40% to 4.09%. The
process capability based on the strength quality was increased from
0.87 to 1.08 as customer oriented. The improvement was able to save
the materials loss for 3.24 millions baht or 0.11 million dollars. The
benefits from the improvement were analyzed from (1) the reduction
of the numbers of non conforming tile using its factory price for
surface coating improvement and (2) the materials saved from the
increment of process capability. The benefit-cost ratio of overall
improvement was high as 7.03. It was non valuable investment in
define, measure, analyses and the initial of improve stages after that
it kept increasing. This was due to there were no benefits in define,
measure, and analyze stages of six sigma since these three stages
mainly determine the cause of problem and its effects rather than
improve the process. The benefit-cost ratio starts existing in the
improve stage and go on. Within each stage, the individual benefitcost
ratio was much higher than the accumulative one as there was an
accumulation of cost since the first stage of six sigma. The
consideration of the benefit-cost ratio during the improvement
project helps make decisions for cost saving of similar activities
during the improvement and for new project. In conclusion, the
determination of benefit-cost ratio behavior through out six sigma
implementation period provides the useful data for managing quality
improvement for the optimal effectiveness. This is the additional
outcome from the regular proceeding of six sigma.
Abstract: This study performs a comparative analysis of the 21 Greek Universities in terms of their public funding, awarded for covering their operating expenditure. First it introduces a DEA/MCDM model that allocates the fund into four expenditure factors in the most favorable way for each university. Then, it presents a common, consensual assessment model to reallocate the amounts, remaining in the same level of total public budget. From the analysis it derives that a number of universities cannot justify the public funding in terms of their size and operational workload. For them, the sufficient reduction of their public funding amount is estimated as a future target. Due to the lack of precise data for a number of expenditure criteria, the analysis is based on a mixed crisp-ordinal data set.
Abstract: The design of a modern aircraft is based on three pillars: theoretical results, experimental test and computational simulations.
As a results of this, Computational Fluid Dynamic (CFD) solvers are
widely used in the aeronautical field. These solvers require the correct
selection of many parameters in order to obtain successful results. Besides, the computational time spent in the simulation depends on
the proper choice of these parameters.
In this paper we create an expert system capable of making an
accurate prediction of the number of iterations and time required for the convergence of a computational fluid dynamic (CFD) solver.
Artificial neural network (ANN) has been used to design the expert system. It is shown that the developed expert system is capable of making an accurate prediction the number of iterations and time
required for the convergence of a CFD solver.
Abstract: Reconfigurable optical add/drop multiplexers
(ROADMs) can be classified into three categories based on their
underlying switching technologies. Category I consists of a single
large optical switch; category II is composed of a number of small
optical switches aligned in parallel; and category III has a single
optical switch and only one wavelength being added/dropped. In this
paper, to evaluate the wavelength-routing capability of ROADMs of
category-II in dynamic optical networks,the dynamic traffic models
are designed based on Bernoulli, Poisson distributions for smooth
and regular types of traffic. Through Analytical and Simulation
results, the routing power of cat-II of ROADM networks for two
traffic models are determined.
Abstract: Foundation of tower crane serves to ensure stability
against vertical and horizontal forces. If foundation stress is not
sufficient, tower crane may be subject to overturning, shearing or
foundation settlement. Therefore, engineering review of stable support
is a highly critical part of foundation design. However, there are not
many professionals who can conduct engineering review of tower
crane foundation and, if any, they have information only on a small
number of cranes in which they have hands-on experience. It is also
customary to rely on empirical knowledge and tower crane renter-s
recommendations rather than designing foundation on the basis of
engineering knowledge. Therefore, a foundation design automation
system considering not only lifting conditions but also overturning
risk, shearing and vertical force may facilitate production of foolproof
foundation design for experts and enable even non-experts to utilize
professional knowledge that only experts can access now. This study
proposes Automatic Design Algorithm for the Tower Crane
Foundations considering load and horizontal force.
Abstract: In this paper, we proposed a new routing protocol for
Unmanned Aerial Vehicles (UAVs) that equipped with directional
antenna. We named this protocol Directional Optimized Link State
Routing Protocol (DOLSR). This protocol is based on the well
known protocol that is called Optimized Link State Routing Protocol
(OLSR). We focused in our protocol on the multipoint relay (MPR)
concept which is the most important feature of this protocol. We
developed a heuristic that allows DOLSR protocol to minimize
the number of the multipoint relays. With this new protocol the
number of overhead packets will be reduced and the End-to-End
delay of the network will also be minimized. We showed through
simulation that our protocol outperformed Optimized Link State
Routing Protocol, Dynamic Source Routing (DSR) protocol and Ad-
Hoc On demand Distance Vector (AODV) routing protocol in
reducing the End-to-End delay and enhancing the overall
throughput. Our evaluation of the previous protocols was based
on the OPNET network simulation tool.
Abstract: Heterogeneity of solid waste characteristics as well as the complex processes taking place within the landfill ecosystem motivated the implementation of soft computing methodologies such as artificial neural networks (ANN), fuzzy logic (FL), and their combination. The present work uses a hybrid ANN-FL model that employs knowledge-based FL to describe the process qualitatively and implements the learning algorithm of ANN to optimize model parameters. The model was developed to simulate and predict the landfill gas production at a given time based on operational parameters. The experimental data used were compiled from lab-scale experiment that involved various operating scenarios. The developed model was validated and statistically analyzed using F-test, linear regression between actual and predicted data, and mean squared error measures. Overall, the simulated landfill gas production rates demonstrated reasonable agreement with actual data. The discussion focused on the effect of the size of training datasets and number of training epochs.
Abstract: The inherent iterative nature of product design and development poses significant challenge to reduce the product design and development time (PD). In order to shorten the time to market, organizations have adopted concurrent development where multiple specialized tasks and design activities are carried out in parallel. Iterative nature of work coupled with the overlap of activities can result in unpredictable time to completion and significant rework. Many of the products have missed the time to market window due to unanticipated or rather unplanned iteration and rework. The iterative and often overlapped processes introduce greater amounts of ambiguity in design and development, where the traditional methods and tools of project management provide less value. In this context, identifying critical metrics to understand the iteration probability is an open research area where significant contribution can be made given that iteration has been the key driver of cost and schedule risk in PD projects. Two important questions that the proposed study attempts to address are: Can we predict and identify the number of iterations in a product development flow? Can we provide managerial insights for a better control over iteration? The proposal introduces the concept of decision points and using this concept intends to develop metrics that can provide managerial insights into iteration predictability. By characterizing the product development flow as a network of decision points, the proposed research intends to delve further into iteration probability and attempts to provide more clarity.
Abstract: Under-representation of women in leadership positions" is still a general phenomenon in Germany despite the high number of implemented measures. The under-representation of female executives in the aviation sector is even worse. In this context our research hypothesis is that the representation and acceptance of women in management positions is determined by corporate culture.
Abstract: The aim of the present study is to analyze the generation of osteoporotic vertebral bone induced by lack of calcium during growth period and analyze its effects for disc degeneration, based on biomechanical and histomorphometrical study. Mechanical and histomorphological characteristics of lumbar vertebral bones and discs of rats with calcium free diet (CFD) were detected and tracked by using high resolution in-vivo micro-computed tomography (in-vivo micro-CT), finite element (FE) and histological analysis. Twenty female Sprague-Dawley rats (6 weeks old, approximate weight 170g) were randomly divided into two groups (CFD group: 10, NOR group: 10). The CFD group was maintained on a refmed calcium-controlled semisynthetic diet without added calcium, to induce osteoporosis. All lumbar (L 1-L6) were scanned by using in vivo micro-CT with 35i.un resolution at 0, 4, 8 weeks to track the effects of CFD on the generation of osteoporosis. The fmdings of the present study indicated that calcium insufficiency was the main factor in the generation of osteoporosis and it induced lumbar vertebral disc degeneration. This study is a valuable experiment to firstly evaluate osteoporotic vertebral bone and disc degeneration induced by lack of calcium during growth period from a biomechanical and histomorphometrical point of view.
Abstract: Limited competition has been a serious concern in infrastructure procurement. Importantly, however, there are normally a number of potential bidders initially showing interest in proposed projects. This paper focuses on tackling the question why these initially interested bidders fade out. An empirical problem is that no bids of fading-out firms are observable. They could decide not to enter the process at the beginning of the tendering or may be technically disqualified at any point in the selection process. The paper applies the double selection model to procurement data from road development projects in developing countries and shows that competition ends up restricted, because bidders are self-selective and auctioneers also tend to limit participation depending on the size of contracts.Limited competition would likely lead to high infrastructure procurement costs, threatening fiscal sustainability and economic growth.
Abstract: In the paper the mathematical model of tumor
growth is considered. New capillary network formation,
which supply cancer cells with the nutrients, is taken into the
account. A formula estimating a tumor growth in connection
with the number of capillaries is obtained.
Abstract: Although so far, many methods for ranking fuzzy numbers
have been discussed broadly, most of them contained some shortcomings,
such as requirement of complicated calculations, inconsistency
with human intuition and indiscrimination. The motivation of
this study is to develop a model for ranking fuzzy numbers based
on the lexicographical ordering which provides decision-makers with
a simple and efficient algorithm to generate an ordering founded on
a precedence. The main emphasis here is put on the ease of use
and reliability. The effectiveness of the proposed method is finally
demonstrated by including a comprehensive comparing different
ranking methods with the present one.
Abstract: The present study focuses on the discussion over the
parameter of Artificial Neural Network (ANN). Sensitivity analysis is
applied to assess the effect of the parameters of ANN on the prediction
of turbidity of raw water in the water treatment plant. The result shows
that transfer function of hidden layer is a critical parameter of ANN.
When the transfer function changes, the reliability of prediction of
water turbidity is greatly different. Moreover, the estimated water
turbidity is less sensitive to training times and learning velocity than
the number of neurons in the hidden layer. Therefore, it is important to
select an appropriate transfer function and suitable number of neurons
in the hidden layer in the process of parameter training and validation.
Abstract: This research proposes an algorithm for the simulation
of time-periodic unsteady problems via the solution unsteady Euler
and Navier-Stokes equations. This algorithm which is called Time
Spectral method uses a Fourier representation in time and hence
solve for the periodic state directly without resolving transients
(which consume most of the resources in a time-accurate scheme).
Mathematical tools used here are discrete Fourier transformations. It
has shown tremendous potential for reducing the computational cost
compared to conventional time-accurate methods, by enforcing
periodicity and using Fourier representation in time, leading to
spectral accuracy. The accuracy and efficiency of this technique is
verified by Euler and Navier-Stokes calculations for pitching airfoils.
Because of flow turbulence nature, Baldwin-Lomax turbulence
model has been used at viscous flow analysis. The results presented
by the Time Spectral method are compared with experimental data. It
has shown tremendous potential for reducing the computational cost
compared to the conventional time-accurate methods, by enforcing
periodicity and using Fourier representation in time, leading to
spectral accuracy, because results verify the small number of time
intervals per pitching cycle required to capture the flow physics.