Abstract: As is known, one of the priority directions of research
works of natural sciences is introduction of applied section of
contemporary mathematics as approximate and numerical methods to
solving integral equation into practice. We fare with the solving of
integral equation while studying many phenomena of nature to whose
numerically solving by the methods of quadrature are mainly applied.
Taking into account some deficiency of methods of quadrature for
finding the solution of integral equation some sciences suggested of
the multistep methods with constant coefficients. Unlike these papers,
here we consider application of hybrid methods to the numerical
solution of Volterra integral equation. The efficiency of the suggested
method is proved and a concrete method with accuracy order p = 4
is constructed. This method in more precise than the corresponding
known methods.
Abstract: In switch mode power inverters, small sized inverters
can be obtained by increasing the switching frequency. Switching
frequency increment causes high driver losses. Also, high dt
di
and
dt
dv
produced by the switching action creates high Electromagnetic
Interference (EMI) and Radio Frequency Interference (RFI). In this
paper, a series half bridge series resonant inverter circuit is simulated
and evaluated practically to demonstrate the turn-on and turn-off
conditions during zero or close to zero voltage switching. Also, the
reverse recovery current effects of the body diode of the MOSFETs
were investigated by operating above and below resonant frequency.
Abstract: One of the key research issues in wireless sensor networks (WSNs) is how to efficiently deploy sensors to cover an area. In this paper, we present a Fishnet Based Dispatch Scheme (FiBDS) with energy aware mobility and interest based sensing angle. We propose two algorithms, one is FiBDS centralized algorithm and another is FiBDS distributed algorithm. The centralized algorithm is designed specifically for the non-time critical applications, commonly known as non real-time applications while the distributed algorithm is designed specifically for the time critical applications, commonly known as real-time applications. The proposed dispatch scheme works in a phase-selection manner. In this in each phase a specific constraint is dealt with according to the specified priority and then moved onto the next phase and at the end of each only the best suited nodes for the phase are chosen. Simulation results are presented to verify their effectiveness.
Abstract: Eco-driving allows the driver to optimize his/her behaviour in order to achieve several types of benefits: reducing pollution emissions, increasing road safety, and fuel saving. One of the main rules for adopting eco-driving is to anticipate the traffic events by avoiding strong acceleration or braking and maintaining a steady speed when possible. Therefore, drivers have to comply with speed limits and time headway. The present study explored the role of three types of motivation and social norms in predicting French drivers- intentions to comply with speed limits and time headway as eco-driving practices as well as examine the variations according to gender and age. 1234 drivers with ages between 18 and 75 years old filled in a questionnaire which was presented as part of an online survey aiming to better understand the drivers- road habits. It included items assessing: a) behavioural intentions to comply with speed limits and time headway according to three types of motivation: reducing pollution emissions, increasing road safety, and fuel saving, b) subjective and descriptive social norms regarding the intention to comply with speed limits and time headway, and c) sociodemographical variables. Drivers expressed their intention to frequently comply with speed limits and time headway in the following 6 months; however, they showed more intention to comply with speed limits as compared to time headway regardless of the type of motivation. The subjective injunctive norms were significantly more important in predicting drivers- intentions to comply with speed limits and time headway as compared to the descriptive norms. In addition, the most frequently reported type of motivation for complying with speed limits and time headway was increasing road safety followed by fuel saving and reducing pollution emissions, hence underlining a low motivation to practice eco-driving. Practical implications of the results are discussed.
Abstract: Decision making preferences to certain criteria
usually focus on positive degrees without considering the negative
degrees. However, in real life situation, evaluation becomes more
comprehensive if negative degrees are considered concurrently.
Preference is expected to be more effective when considering both
positive and negative degrees of preference to evaluate the best
selection. Therefore, the aim of this paper is to propose the
conflicting bifuzzy preference relations in group decision making by
utilization of a novel score function. The conflicting bifuzzy
preference relation is obtained by introducing some modifications on
intuitionistic fuzzy preference relations. Releasing the intuitionistic
condition by taking into account positive and negative degrees
simultaneously and utilizing the novel score function are the main
modifications to establish the proposed preference model. The
proposed model is tested with a numerical example and proved to be
simple and practical. The four-step decision model shows the
efficiency of obtaining preference in group decision making.
Abstract: Students often adopt routine practicing as learning
strategy for mathematics. The reason is they are often bound and
trained to solving conventional-typed questions in Mathematics in
high school. This will be problematic if students further consolidate
this practice in university. Therefore, the Department of Mathematics
emphasized and integrated the Discovery-enriched approach in the
undergraduate curriculum. This paper presents the details of
implementing the Discovery-enriched Curriculum by providing
adequate platform for project-learning, expertise for guidance and
internship opportunities for students majoring in Mathematics. The
Department also provided project-learning opportunities to
mathematics courses targeted for students majoring in other science or
engineering disciplines. The outcome is promising: the research
ability and problem solving skills of students are enhanced.
Abstract: The production of glass, ceramic materials and many non-ferrous metals (Zn, Cu, Pb, etc.), ferrous metals (pig iron) and others is connected with the use of a considerable number of initial solid raw materials. Before carrying out the basic technological processes (oxidized roasting, melting, agglomeration, baking) it is necessary to mix and homogenize the raw materials that have different chemical and phase content, granulometry and humidity. For this purpose zinc sulfide concentrates differing in origin are studied for their more complete characteristics using chemical, X-ray diffraction analyses, DTA and TGA as well as Mössbauer spectroscopy. The phases established in most concentrates are: β-ZnS, mZnS.nFeS, FeS2, CuFeS2, PbS, SiO2 (α-quartz). With the help of the developed by us a Web-based information system for a continued period of time different mix proportions from zinc concentrates are calculated and used in practice (roasting in fluidized bed reactor), which have to conform to the technological requirements of the zinc hydrometallurgical technological scheme.
Abstract: Monitoring lightning electromagnetic pulses (sferics) and other terrestrial as well as extraterrestrial transient radiation signals is of considerable interest for practical and theoretical purposes in astro- and geophysics as well as meteorology. Managing a continuous flow of data, automation of the analysis and classification process is important. Features based on a combination of wavelet and statistical methods proved efficient for this task and serve as input into a radial basis function network that is trained to discriminate transient shapes from pulse like to wave like. We concentrate on signals in the Very Low Frequency (VLF, 3 -30 kHz) range in this paper, but the developed methods are independent of this specific choice.
Abstract: Landscape connectivity combines a description of the
physical structure of the landscape with special species- response to
that structure, which forms the theoretical background of applying
landscape connectivity principles in the practices of landscape
planning and design. In this study, a residential development project in
the southern United States was used to explore the meaning of
landscape connectivity and its application in town planning. The vast
rural landscape in the southern United States is conspicuously
characterized by the hedgerow trees or groves. The patchwork
landscape of fields surrounded by high hedgerows is a traditional and
familiar feature of the American countryside. Hedgerows are in effect
linear strips of trees, groves, or woodlands, which are often critical
habitats for wildlife and important for the visual quality of the
landscape. Based on geographic information system (GIS) and
statistical analysis (FRAGSTAT), this study attempts to quantify the
landscape connectivity characterized by hedgerows in south Alabama
where substantial areas of authentic hedgerow landscape are being
urbanized due to the ever expanding real estate industry and high
demand for new residential development. The results of this study
shed lights on how to balance the needs of new urban development and
biodiversity conservation by maintaining a higher level of landscape
connectivity, thus will inform the design intervention.
Abstract: This paper deals with a novel approach of power
transformers diagnostics. This approach identifies the exact location
and the range of a fault in the transformer and helps to reduce
operation costs related to handling of the faulty transformer, its
disassembly and repair. The advantage of the approach is a
possibility to simulate healthy transformer and also all faults, which
can occur in transformer during its operation without its
disassembling, which is very expensive in practice. The approach is
based on creating frequency dependent impedance of the transformer
by sweep frequency response analysis measurements and by 3D FE
parametrical modeling of the fault in the transformer. The parameters
of the 3D FE model are the position and the range of the axial short
circuit. Then, by comparing the frequency dependent impedances of
the parametrical models with the measured ones, the location and the
range of the fault is identified. The approach was tested on a real
transformer and showed high coincidence between the real fault and
the simulated one.
Abstract: This paper presents an optimal design of poly-phase induction motor using Quadratic Interpolation based Particle Swarm Optimization (QI-PSO). The optimization algorithm considers the efficiency, starting torque and temperature rise as objective function (which are considered separately) and ten performance related items including harmonic current as constraints. The QI-PSO algorithm was implemented on a test motor and the results are compared with the Simulated Annealing (SA) technique, Standard Particle Swarm Optimization (SPSO), and normal design. Some benchmark problems are used for validating QI-PSO. From the test results QI-PSO gave better results and more suitable to motor-s design optimization. Cµ code is used for implementing entire algorithms.
Abstract: Analytical seismic response of multi-story building
supported on base isolation system is investigated under real
earthquake motion. The superstructure is idealized as a shear type
flexible building with lateral degree-of-freedom at each floor. The
force-deformation behaviour of the isolation system is modelled by
the bi-linear behaviour which can be effectively used to model all
isolation systems in practice. The governing equations of motion of
the isolated structural system are derived. The response of the system
is obtained numerically by step-by-method under three real recorded
earthquake motions and pulse motions associated in the near-fault
earthquake motion. The variation of the top floor acceleration, interstory
drift, base shear and bearing displacement of the isolated
building is studied under different initial stiffness of the bi-linear
isolation system. It was observed that the high initial stiffness of the
isolation system excites higher modes in base-isolated structure and
generate floor accelerations and story drift. Such behaviour of the
base-isolated building especially supported on sliding type of
isolation systems can be detrimental to sensitive equipment installed
in the building. On the other hand, the bearing displacement and base
shear found to reduce marginally with the increase of the initial
stiffness of the initial stiffness of the isolation system. Further, the
above behaviour of the base-isolated building was observed for
different parameters of the bearing (i.e. post-yield stiffness and
characteristic strength) and earthquake motions (i.e. real time history
as well as pulse type motion).
Abstract: To solve the quick and accurate level-adjusting
problem in the process of spacecraft precise mating, automatic leveling
and equalizing hoist device for spacecraft is developed. Based on
lifting point adjustment by utilizing XY-workbench, the leveling and
equalizing controller by a self-adaptive control algorithm is proposed.
By simulation analysis and lifting test using engineering prototype,
validity and reliability of the hoist device is verified, which can meet
the precision mating requirements of practical applications for
spacecraft.
Abstract: In the present paper, we use generalized B-Spline curve in trigonometric form on circular domain, to capture the transcendental nature of circle involute curve and uncertainty characteristic of design. The required involute curve get generated within the given tolerance limit and is useful in gear design.
Abstract: Global Software Development (GSD) projects are
passing through different boundaries of a company, country and even
in other continents where time zone differs between both sites.
Beside many benefits of such development, research declared plenty
of negative impacts on these GSD projects. It is important to
understand problems which may lie during the execution of GSD
project with different time zones. This research project discussed and
provided different issues related to time delays in GSD projects. In
this paper, authors investigated some of the time delay factors which
usually lie in GSD projects with different time zones. This
investigation is done through systematic review of literature.
Furthermore, the practices to overcome these delay factors which
have already been reported in literature and GSD organizations are
also explored through literature survey and case studies.
Abstract: A prototype for audio and video capture and compression in real time on a Linux platform has been developed. It is able to visualize both the captured and the compressed video at the same time, as well as the captured and compressed audio with the goal of comparing their quality. As it is based on free code, the final goal is to run it in an embedded system running Linux. Therefore, we would implement a node to capture and compress such multimedia information. Thus, it would be possible to consider the project within a larger one aimed at live broadcast of audio and video using a streaming server which would communicate with our node. Then, we would have a very powerful and flexible system with several practical applications.
Abstract: Collaborative working environments for distance
education can be considered as a more generic form of contemporary
remote labs. At present, the majority of existing real laboratories are
not constructed to allow the involved participants to collaborate in
real time. To make this revolutionary learning environment possible
we must allow the different users to carry out an experiment
simultaneously. In recent times, multi-user environments are
successfully applied in many applications such as air traffic control
systems, team-oriented military systems, chat-text tools, multi-player
games etc. Thus, understanding the ideas and techniques behind these
systems could be of great importance in the contribution of ideas to
our e-learning environment for collaborative working. In this
investigation, collaborative working environments from theoretical
and practical perspectives are considered in order to build an
effective collaborative real laboratory, which allows two students or
more to conduct remote experiments at the same time as a team. In
order to achieve this goal, we have implemented distributed system
architecture, enabling students to obtain an automated help by either
a human tutor or a rule-based e-tutor.
Abstract: Quality of Service (QoS) Routing aims to find path between source and destination satisfying the QoS requirements which efficiently using the network resources and underlying routing algorithm and to fmd low-cost paths that satisfy given QoS constraints. One of the key issues in providing end-to-end QoS guarantees in packet networks is determining feasible path that satisfies a number of QoS constraints. We present a Optimized Multi- Constrained Routing (OMCR) algorithm for the computation of constrained paths for QoS routing in computer networks. OMCR applies distance vector to construct a shortest path for each destination with reference to a given optimization metric, from which a set of feasible paths are derived at each node. OMCR is able to fmd feasible paths as well as optimize the utilization of network resources. OMCR operates with the hop-by-hop, connectionless routing model in IP Internet and does not create any loops while fmding the feasible paths. Nodes running OMCR not necessarily maintaining global view of network state such as topology, resource information and routing updates are sent only to neighboring nodes whereas its counterpart link-state routing method depend on complete network state for constrained path computation and that incurs excessive communication overhead.
Abstract: As the enormous amount of on-line text grows on the
World-Wide Web, the development of methods for automatically
summarizing this text becomes more important. The primary goal of
this research is to create an efficient tool that is able to summarize
large documents automatically. We propose an Evolving
connectionist System that is adaptive, incremental learning and
knowledge representation system that evolves its structure and
functionality. In this paper, we propose a novel approach for Part of
Speech disambiguation using a recurrent neural network, a paradigm
capable of dealing with sequential data. We observed that
connectionist approach to text summarization has a natural way of
learning grammatical structures through experience. Experimental
results show that our approach achieves acceptable performance.
Abstract: The creation of a sustainable future depends on the knowledge and involvement of the people, as well as an understanding of the consequences of individual actions. Construction industry has long been associated with the detrimental effects to our mother earth. In Malaysia, the government, professional bodies and private companies are beginning to take heed in the necessity to reduce this environmental problem without restraining the need for development. This paper focuses on the actions undertaken by the Malaysian government, non-government organizations and construction players in promoting sustainability in construction. To ensure that those concerted efforts are not only skin deep in its impact, a survey was conducted to investigate the awareness of the developers regarding this issue and whether those developers has absorb the concept of sustainable construction in their current practices. The survey revealed that although the developers are aware of the rising issues on sustainability, little efforts are generated from them in implementing it. More effort is necessary to boost this application and further stimulate actions and strategies towards a sustainable built environment.