Abstract: The use of power system stabilizers (PSSs) to damp
power system swing mode of oscillations is practical important. Our
purpose is to retune the power system stabilizer (PSS1A) parameters
in Unitrol D produced by ABB– was installed in 1995in Benghazi
North Power Plants (BNPPs) at General Electricity Company of
Libya (GECOL). The optimal values of the power system stabilizer
(PSS1A) parameters are determined off-line by a particle swarm
optimization technique (PSO). The objective is to damp the local and
inter-area modes of oscillations that occur following power system
disturbances. The retuned power system stabilizer (PSS1A) can cope
with large disturbance at different operating points and has enhanced
power system stability.
Abstract: A Comparison and evaluation of the different
condition monitoring (CM) techniques was applied experimentally
on RC e.g. Dynamic cylinder pressure and crankshaft Instantaneous
Angular Speed (IAS), for the detection and diagnosis of valve faults
in a two - stage reciprocating compressor for a programme of
condition monitoring which can successfully detect and diagnose a
fault in machine. Leakage in the valve plate was introduced
experimentally into a two-stage reciprocating compressor. The effect
of the faults on compressor performance was monitored and the
differences with the normal, healthy performance noted as a fault
signature been used for the detection and diagnosis of faults.
The paper concludes with what is considered to be a unique
approach to condition monitoring. First, each of the two most useful
techniques is used to produce a Truth Table which details the
circumstances in which each method can be used to detect and
diagnose a fault. The two Truth Tables are then combined into a
single Decision Table to provide a unique and reliable method of
detection and diagnosis of each of the individual faults introduced
into the compressor. This gives accurate diagnosis of compressor
faults.
Abstract: This paper presents the modeling results of an
innovative system for the temperature control in the interior
compartment of a stationary automobile facing the solar energy from
the sun. A very thin layer of PCM inside a pouch placed in the
ceiling of the car in which the heating energy is absorbed and release
with melting and solidification of phase change materials. As a result
the temperature of the car interior is maintained in the comfort
condition. The amount of required PCM has been calculated to be
about 755 g. The PCM-temperature controlling system is simple and
has a potential to be implemented as a practical solution to prevent
undesirable heating of the automobile-s cabin.
Abstract: In the past few decades, researchers have witnessed a
paradigm shift in Human Resource Management-from individual
performance to organizational outcomes with the role of Human
resource (HR) managers becoming increasingly significant to the
organization. In such a context, it is important to examine HR
practices from a strategic perspective on the sustained competitive
advantage (SCA) of the organizations. The present study explores
how Indian organisations look at their human resources strategically
when faced with competitive environment. Also, it explores strategic
initiatives being taken to manage human resources within the
organisations and how these initiatives promote SCA in terms of
enhancing the overall customer-centric delivery of goods and
services.
Abstract: The main objective of this paper is to analyse the influence of preparation and control of orders on performance. The focused activities explored in this research are: procurement, production and distribution. These changes in performance were obtained through improvement of the supply chain. It is proved using all the company activities that it is possible to increase de efficiency and do services in an adequate way, placing the products in the market efficiently. For that, it was explored the importance of the supply chain, with privilege to the practical environment and the quantification of the obtained results.
Abstract: We study dynamic instability in high-rise steel moment
resisting frames (SMRFs) subjected to synthetic long-period ground
motions caused by hypothetical huge subduction earthquakes. Since
long duration as well as long dominant periods is a characteristic of
long-period ground motions, interstory drifts may enter the negative
postyield stiffness range many times when high-rise buildings are
subjected to long-period ground motions. Through the case studies of
9 high-rise SMRFs designed in accordance with the Japanese design
practice in 1980s, we demonstrate that drifting, or accumulation of
interstory drifts in one direction, occurs at the lower stories of the
SMRFs, if their natural periods are close to the dominant periods of the
long-period ground motions. The drifting led to residual interstory
drift ratio over 0.01, or to collapse if the design base shear was small.
Abstract: Obfuscation is a low cost software protection
methodology to avoid reverse engineering and re engineering of
applications. Source code obfuscation aims in obscuring the source
code to hide the functionality of the codes. This paper proposes an
Array data transformation in order to obfuscate the source code
which uses arrays. The applications using the proposed data
structures force the programmer to obscure the logic manually. It
makes the developed obscured codes hard to reverse engineer and
also protects the functionality of the codes.
Abstract: There have been different approaches to compute the
analytic instantaneous frequency with a variety of background reasoning
and applicability in practice, as well as restrictions. This paper presents an adaptive Fourier decomposition and (α-counting) based
instantaneous frequency computation approach. The adaptive Fourier
decomposition is a recently proposed new signal decomposition
approach. The instantaneous frequency can be computed through the so called mono-components decomposed by it. Due to the fast energy
convergency, the highest frequency of the signal will be discarded by the adaptive Fourier decomposition, which represents the noise of
the signal in most of the situation. A new instantaneous frequency
definition for a large class of so-called simple waves is also proposed
in this paper. Simple wave contains a wide range of signals for which
the concept instantaneous frequency has a perfect physical sense.
The α-counting instantaneous frequency can be used to compute the highest frequency for a signal. Combination of these two approaches one can obtain the IFs of the whole signal. An experiment is demonstrated the computation procedure with promising results.
Abstract: Recently, neural networks have shown good
results for detection of a certain pattern in a given image. In
our previous papers [1-5], a fast algorithm for pattern
detection using neural networks was presented. Such
algorithm was designed based on cross correlation in the
frequency domain between the input image and the weights
of neural networks. Image conversion into symmetric shape
was established so that fast neural networks can give the
same results as conventional neural networks. Another
configuration of symmetry was suggested in [3,4] to improve
the speed up ratio. In this paper, our previous algorithm for
fast neural networks is developed. The frequency domain
cross correlation is modified in order to compensate for the
symmetric condition which is required by the input image.
Two new ideas are introduced to modify the cross correlation
algorithm. Both methods accelerate the speed of the fast
neural networks as there is no need for converting the input
image into symmetric one as previous. Theoretical and
practical results show that both approaches provide faster
speed up ratio than the previous algorithm.
Abstract: Nowadays, where most of the leading economies are
service oriented and e-business is being widely used for their
management, supply chain management has become one of the most
studied and practiced fields. Quality has an important role on today-s
business processes, so it is important to understand the impact of IT
service quality on the performance of supply chains. This paper will
start by analyzing the Supply Chain Operations Reference (SCOR)
model and each of its five activities: Plan, Source, Make, Delivery,
and Return. This article proposes a framework for analyzing Effect of
IT Service Quality on Supply Chain Performance. Using the
proposed framework, hypotheses are framed for the direct effect of IT
service quality on Supply Chain Performance and its indirect effect
through effective Supply Chain Management. The framework will be
validated empirically based on the surveys of executives of various
organizations and statistical analyses of the data collected.
Abstract: This paper describes how the correct endian mode of
the TMS320C6713 DSK board can be identified. It also explains how
the TMS320C6713 DSK board can be used in the little endian and in
the big endian modes for assembly language programming in
particular and for signal processing in general. Similarly, it discusses
how crucially important it is for a user of the TMS320C6713 DSK
board to identify the mode of operation and then use it correctly
during the development stages of the assembly language
programming; otherwise, it will cause unnecessary confusion and
erroneous results as far as storing data into the memory and loading
data from the memory is concerned. Furthermore, it highlights and
strongly recommends to the users of the TMS320C6713 DSK board
to be aware of the availability and importance of various display
options in the Code Composer Studio (CCS) for correctly
interpreting and displaying the desired data in the memory. The
information presented in this paper will be of great importance and
interest to those practitioners and developers who wants to use the
TMS320C6713 DSK board for assembly language programming as
well as input-output signal processing manipulations. Finally,
examples that clearly illustrate the concept are presented.
Abstract: Buildings and associated construction methods have a significant impact on the environment. As construction activity increases in Kuwait, there is a need to create design and construction strategies which will minimize the environmental impact of new buildings. Green construction is a design philosophy intended to improve the sustainability of construction by the minimization of resource depletion and CO2 emissions throughout the life cycle of buildings. This paper presents and discusses the results of a survey that was conducted in Kuwait, with the objective of investigating the awareness of developers and other stakeholders regarding their understanding and use of green construction strategies. The results of the survey demonstrate that whilst there seems to be a reasonable level of awareness amongst the stakeholders, this awareness is not currently well reflected in the design and construction practices actually being applied. It is therefore concluded is there is a pressing need for intervention from Government in order that the use of sustainable green design and construction strategies becomes the norm in Kuwait.
Abstract: In a product development process, understanding the functional behavior of the system, the role of components in achieving functions and failure modes if components/subsystem fails its required function will help develop appropriate design validation and verification program for reliability assessment. The integration of these three issues will help design and reliability engineers in identifying weak spots in design and planning future actions and testing program. This case study demonstrate the advantage of unascertained theory described in the subjective cognition uncertainty, and then applies blind number (BN) theory in describing the uncertainty of the mechanical system failure process and the same time used the same theory in bringing out another mechanical reliability system model. The practical calculations shows the BN Model embodied the characters of simply, small account of calculation but betterforecasting capability, which had the value of macroscopic discussion to some extent.
Abstract: For any country the project management has been a
vital part for its development. The highly competitive business world
has created tremendous pressure on the project managers to achieve
success. The pressure is derived from survival and profit building in
business organizations which compels the project managers to pursue
unethical practices. As a result unethical activities in business
projects can be found easily where situations or issues arise due to
dubious business practice, high corruption, or absolute violation of
the law. The recent spur on Commonwealth games to be organized in
New Delhi indicates towards the same. It has been seen that the
project managers mainly focus on cost, time, and quality rather than
social impact and long term effects of the project. Surprisingly the
literature as well as the practitioner-s perspective also does not
identify the role of ethics in project success. This paper identifies
ethics as the fourth most important dimension in the project based
organizations. The paper predicts that the approach of considering
ethics will result in sustainability of the project. It will increase
satisfaction and loyalty of the customers as well as create harmony,
trust, brotherhood, values and morality among the team members.
This paper is conceptual in nature as inadequate literature exists
linking the project success with an ethical approach.
Abstract: It is important problems to increase the detection rates
and reduce false positive rates in Intrusion Detection System (IDS).
Although preventative techniques such as access control and
authentication attempt to prevent intruders, these can fail, and as a
second line of defence, intrusion detection has been introduced. Rare
events are events that occur very infrequently, detection of rare
events is a common problem in many domains. In this paper we
propose an intrusion detection method that combines Rough set and
Fuzzy Clustering. Rough set has to decrease the amount of data and
get rid of redundancy. Fuzzy c-means clustering allow objects to
belong to several clusters simultaneously, with different degrees of
membership. Our approach allows us to recognize not only known
attacks but also to detect suspicious activity that may be the result of
a new, unknown attack. The experimental results on Knowledge
Discovery and Data Mining-(KDDCup 1999) Dataset show that the
method is efficient and practical for intrusion detection systems.
Abstract: This paper discusses a curriculum approach that will
give emphasis on practical portions of teaching network security
subjects in information and communication technology courses. As
we are well aware, the need to use a practice and application oriented
approach in education is paramount. Research on active learning and
cooperative groups have shown that students grasps more and have
more tendency towards obtaining and realizing soft skills like
leadership, communication and team work as opposed to the more
traditional theory and exam based teaching and learning. While this
teaching and learning paradigm is relatively new in Malaysia, it has
been practiced widely in the West. This paper examines a certain
approach whereby students learning wireless security are divided into
and work in small and manageable groups where there will be 2
teams which consist of black hat and white hat teams. The former
will try to find and expose vulnerabilities in a wireless network while
the latter will try their best to prevent such attacks on their wireless
networks using hardware, software, design and enforcement of
security policy and etc. This paper will try to show that the approach
taken plus the use of relevant and up to date software and hardware
and with suitable environment setting will hopefully expose students
to a more fruitful outcome in terms of understanding of concepts,
theories and their motivation to learn.
Abstract: Most of the commercial gluten free products are
nutritionally inferior when compared to gluten containing
counterparts as manufacturers most often use the refined flours and
starches. So it is possible that people on gluten free diet have low
intake of fibre content. The foxtail millet flour and copra meal are
gluten free and have high fibre and protein contents. The formulation
of fibre rich gluten free cookies was optimized by response surface
methodology considering independent process variables as proportion
of Foxtail millet (Setaria italica) flour in mixed flour, fat content and
guar gum. The sugar, sodium chloride, sodium bicarbonates and
water were added in fixed proportion as 60, 1.0, 0.4 and 20% of
mixed flour weight, respectively. Optimum formulation obtained for
maximum spread ratio, fibre content, surface L-value, overall
acceptability and minimum breaking strength were 80% foxtail millet
flour in mixed flour, 42.8 % fat content and 0.05% guar gum.
Abstract: Milk is a very important nutrient. Low productivity is
a problem of Turkish dairy farming. During recent years, Turkish government has supported cooperatives that assist milk producers and
encouraged farmers to become cooperative members. Turkish
government established several ways to support specially smallholders. For example Ministry of Agriculture and Rural Affairs
(MARA) provided two to four cows to villagers on a grant or loan basis with a long repayment period at low interest rates by
cooperatives. Social Support Project in Rural Areas (SSPRA) is
another support program targeting only disadvantaged people,
especially poor villager. Both programs have a very strong social
support component and similar objectives. But there are minor
differences between them in terms of target people, terms and conditions of the credit supplied Isparta province in Mediterranean region of Turkey is one of the
supported regions. MARA distributed dairy cows to 1072 farmers through 16 agricultural cooperatives in Isparta province in the context
of SSPRA. In this study, economic-social impacts on dairy cattle project
implemented through cooperatives were examined in Isparta. Primary data were collected from 12 cooperatives- president. The
data were obtained by personal interview through a questionnaire and
to cooperatives and given to farms benefiting from the project in
order to reveal the economic and social developments.
Finding of the study revealed that project provided new job
opportunities and improved quality of livestock. It was found that producers who benefited from the project were more willing to
participate in cooperative or other producer organizations.
Abstract: High Performance Work Systems (HPWS) generally give rise to positive impacts on employees by increasing their commitments in workplaces. While some argued this actually have considerable negative impacts on employees with increasing possibilities of imposing strains caused by stress and intensity of such work places. Do stressful workplaces hamper employee commitment? The author has tried to find the answer by exploring linkages between HPWS practices and its impact on employees in Japanese organizations. How negative outcomes like job intensity and workplaces and job stressors can influence different forms of employees- commitments which can be a hindrance to their performance. Design: A close ended questionnaire survey was conducted amongst 16 large, medium and small sized Japanese companies from diverse industries around Chiba, Saitama, and Ibaraki Prefectures and in Tokyo from the month of October 2008 to February 2009. Questionnaires were aimed to the non managerial employees- perceptions of HPWS practices, their behavior, working life experiences in their work places. A total of 227 samples are used for analysis in the study. Methods: Correlations, MANCOVA, SEM Path analysis using AMOS software are used for data analysis in this study. Findings: Average non-managerial perception of HPWS adoption is significantly but negatively correlated to both work place Stressors and Continuous commitment, but positively correlated to job Intensity, Affective, Occupational and Normative commitments in different workplaces at Japan. The path analysis by SEM shows significant indirect relationship between Stressors and employee Affective organizational commitment and Normative organizational commitments. Intensity also has a significant indirect effect on Occupational commitments. HPWS has an additive effect on all the outcomes variables. Limitations: The sample size in this study cannot be a representative to the entire population of non-managerial employees in Japan. There were no respondents from automobile, pharmaceuticals, finance industries. The duration of the survey coincided in a period when Japan as most of the other countries is under going recession. Biases could not be ruled out completely. We must take cautions in interpreting the results of studies as they cannot be generalized. And the path analysis cannot provide the complete causality of the inter linkages between the variables used in the study. Originality: There have been limited studies on linkages in HPWS adoptions and their impacts on employees- behaviors and commitments in Japanese workplaces. This study may provide some ingredients for further research in the fields of HRM policies and practices and their linkages on different forms of employees- commitments.
Abstract: Response surface methodology (RSM) is a very
efficient tool to provide a good practical insight into developing new
process and optimizing them. This methodology could help
engineers to raise a mathematical model to represent the behavior of
system as a convincing function of process parameters.
Through this paper the sequential nature of the RSM surveyed for process
engineers and its relationship to design of experiments (DOE), regression
analysis and robust design reviewed. The proposed four-step procedure in
two different phases could help system analyst to resolve the parameter
design problem involving responses. In order to check accuracy of the
designed model, residual analysis and prediction error sum of squares
(PRESS) described.
It is believed that the proposed procedure in this study can resolve a
complex parameter design problem with one or more responses. It can be
applied to those areas where there are large data sets and a number of
responses are to be optimized simultaneously. In addition, the proposed
procedure is relatively simple and can be implemented easily by using
ready-made standard statistical packages.